离心泵作透平最佳工况点下的瞬态流动特性分析

doi:10.3901/JME.2021.22.395

机械工程学报 ›› 2021, Vol. 57 ›› Issue (22): 395-405.doi: 10.3901/JME.2021.22.395

扫码分享

离心泵作透平最佳工况点下的瞬态流动特性分析

林通^1,2, 李晓俊¹, 朱祖超¹, 谢华东², 胡建新¹

1. 浙江理工大学流体传输系统技术国家地方联合实验室杭州 310018;
2. 江西应用技术职业学院机械与电子工程学院赣州 341000

收稿日期:2020-11-01 修回日期:2021-08-06 出版日期:2021-11-20 发布日期:2022-02-28
通讯作者: 朱祖超(通信作者),男,1966年出生,博士,教授,博士研究生导师。主要研究方向为流体输送与装备、智能传输装备开发及工程。E-mail:zhuzuchao@zstu.edu.cn
作者简介:林通,男,1992年出生,博士研究生,讲师。主要研究方向为液力透平。E-mail:tlin9243@sina.com
基金资助:
国家自然科学基金（U1709209，51536008，U2006221，51906224，51906223）、浙江省重点研发计划（2020C01027）和江西省教育厅科学技术研究（GJJ191344）资助项目。

Analysis of the Unsteady Flow Characteristics of Chemical Centrifugal Pump as Turbine at the Best Efficiency Point Condition

LIN Tong^1,2, LI Xiaojun¹, ZHU Zuchao¹, XIE Huadong², HU Jianxin¹

1. National-Provincial Joint Engineering Laboratory for Fluid Transmission System Technology, Zhejiang Sci-Tech University, Hangzhou 310018;
2. School of Mechanical and Electronic Engineering, Jiangxi College of Applied Technology, Ganzhou 341000

Received:2020-11-01 Revised:2021-08-06 Online:2021-11-20 Published:2022-02-28

摘要/Abstract

摘要： 为揭示离心泵作透平在最佳工况点下主要过流部件的瞬态流动特性，采用修正的PANS模型对一台比转速为90的离心泵作透平的瞬态流动特性进行数值模拟，通过试验验证数值计算的准确性；根据叶片的进、出口速度三角形计算理论最佳工况点，并对最佳工况下叶栅内部的流动规律进行预测；对蜗壳、叶轮在最佳工况点下的内部瞬态流动特性进行分析。结果表明，叶轮理论进、出口最佳工况点分别为55 m³/h、108 m³/h，实际最佳工况点为80 m³/h；叶片与蜗壳隔舌的动静干涉会促进隔舌前缘旋涡的脱落，当叶轮前缘与隔舌前缘平齐时，蜗壳内压力脉动强度最低；叶栅内旋涡的脱落频率约为2f_n，涡量的演变主要由其输运方程中的拉伸项及科氏力项共同主导；吸力面附近涡量的演变对叶轮前、中部流道内的压力脉动影响较大，而叶片尾缘涡量的演变对叶轮出口处的压力脉动影响较大。研究结果可为提高离心泵作透平在余能回收系统中的运行稳定性提供参考。

关键词: 离心泵, 液力透平, 最佳工况, 瞬态流动特性, 数值模拟

Abstract: Considering that the self-developed deep-sea electric pump operates under off-design conditions, its internal unsteady fluid radial force may cause vibration of the pump and even bring harm to the whole mining system. At present, it is impossible to calculate the radial force directly through theoretical formula. Therefore, the experimental and numerical simulation methods are used to study the regular and the production mechanism. Firstly, the accuracy of the numerical simulation method is verified by hydraulic performance test of the electric pump, and then the pressure distribution in the six-stage deep-sea electric pump and the radial force distribution of the fluid in the pump and its generating mechanism are studied. Finally, the radial force distribution law of two-stage deep-sea electric pump under different flow rates is compared and analyzed. The results show that the radial force in impeller at all stages varies periodically, and the stronger the regularity is at the last stage; the change period of radial force in impeller at all stages is related to the number of impeller blades. When other parameters remain unchanged, the smaller the flow rate is, the greater the radial force is, and the stronger the fluctuation is.

Key words: centrifugal pump, hydraulic turbine, optimal working condition, unsteady flow characteristics, numerical simulation

中图分类号:

TH311

林通, 李晓俊, 朱祖超, 谢华东, 胡建新. 离心泵作透平最佳工况点下的瞬态流动特性分析[J]. 机械工程学报, 2021, 57(22): 395-405.

LIN Tong, LI Xiaojun, ZHU Zuchao, XIE Huadong, HU Jianxin. Analysis of the Unsteady Flow Characteristics of Chemical Centrifugal Pump as Turbine at the Best Efficiency Point Condition[J]. Journal of Mechanical Engineering, 2021, 57(22): 395-405.

参考文献

[1] LYDON T, COUGHLAN P, MCNABOLA A. Pressure management and energy recovery in water distribution networks:Development of design and selection methodologies using three pump-as-turbine case studies[J]. Renewable Energy, 2017, 114:1038-1050.
[2] LIMA G M, LUVIZOTTO E, BRENTAN B M. Selection and location of pumps as turbines substituting pressure reducing valves[J]. Renewable Energy, 2017, 109:392-405.
[3] SINGH A D S C P. Influence of nonflow zone(back cavity) geometry on the performance of pumps as turbines[J]. Journal of Fluids Engineering, 2018, 104:121107-1-121107-13.
[4] DELGADO J, FERREIRA J P, COVAS D I C, et al. Variable speed operation of centrifugal pumps running as turbines:Experimental investigation[J]. Renewable Energy, 2019, 142:437-450.
[5] SANJAY V J, RAJESH N P. Experimental investigations of cavitation characteristics of pump running in turbine mode[J]. Journal of Energy Engineering, 2017, 143(1):12.
[6] 代翠, 孔繁余, 董亮, 等. 基于响应面法的离心泵作透平水力和声学性能优化[J]. 农业工程学报, 2015, 31(15):40-47. DAI Cui, KONG Fanyu, DONG Liang, et al. Hydraulic and acoustic property optimization for centrifugal pump as turbine based on response surface method[J]. Transactions of the Chinese Society of Agricultural Engineering, 2015, 31(15):40-47.
[7] 王桃, 孔繁余, 刘莹莹, 等. 叶片进口安放角对泵作透平外特性影响的数值模拟与验证[J]. 农业工程学报, 2017, 33(15):98-104. WANG Tao, KONG Fanyu, LIU Yingying, et al. Numerical simulation and validation of effects of blade inlet angle on performance of pump-as-turbine[J]. Transactions of the Chinese Society of Agricultural Engineering, 2017, 33(15):98-104.
[8] 董亮, 代翠, 孔繁余, 等. 叶片出口安放角对离心泵作透平噪声的影响[J]. 农业工程学报, 2015, 31(6):69-75. DONG Liang, DAI Cui, KONG Fanyu, et al. Impact of blade outlet angle on acoustic of centrifugal pump as turbine[J]. Transactions of the Chinese Society of Agricultural Engineering, 2015, 31(6):69-75.
[9] YANG S S, WANG C, CHEN K, et al. Research on blade thickness influencing pump as turbine[J]. Advances in Mechanical Engineering, 2015(6):190530.
[10] YANG S S, KONG F Y, QU X Y, et al. Influence of blade number on the performance and pressure pulsations in a pump used as a turbine[J]. Journal of Fluids Engineering2012, 134:10.
[11] YANG S S, LI H L, KONG F Y, et al. Effects of the radial gap between impeller tips and volute tongue influencing the performance and pressure pulsations of pump as turbine[J]. Journal of Fluids Engineering, 2014, 136:054501-1-054501-8.
[12] YANG S S, LIU H L, KONG F Y, et al. Experimental, numerical, and theoretical research on impeller diameter influencing centrifugal pump-as-turbine[J]. Journal of Energy Engineering, 2013, 139:299-307.
[13] SU X, HUANG S, LI Y, et al. Numerical and experimental research on multi-stage pump as turbine system[J]. International Journal of Green Energy, 2017, 14:996-1004.
[14] BINAMA M, SU W T, CAI W H, et al. Blade trailing edge position influencing pump as turbine (PAT) pressure field under part-load conditions[J]. Renewable Energy, 2019, 136:33-47.
[15] GAO Y, DANG R. Numerical characterization of the effects of flow rate on pressure and velocity distribution of pump as turbine[J]. Current Science, 2019, 117:57-63.
[16] PÁSCOA J C, SILVA F J, PINHEIRO J S, et al. Accuracy details in realistic CFD modeling of an industrial centrifugal pump in direct and reverse modes[J]. Journal of Thermal Science, 2010, 19:491-499.
[17] 王晓晖, 杨军虎, 郭艳磊, 等. 反转泵液力透平速度滑移机理[J]. 机械工程学报, 2018, 54(24):189-196. WANG Xiaohui, YANG Junhu, GUO Yanlei, et al. Research on slip phenomenon of pumps as turbines[J]. Journal of Mechanical Engineering, 2018, 54(24):189-196.
[18] 韩伟, 李雪峰, 陈昊, 等. 液力透平动静叶栅内的流动特性[J]. 流体机械, 2017, 45(2):46-49, 56. HAN Wei, LI Xuefeng, CHEN Hao, et al. Flow characteristics of the rotor-stator cascades in a hydraulic turbine[J]. Fluid Machinery, 2017, 45(2):46-49, 56.
[19] 代翠, 孔繁余, 董亮, 等. 泵作透平尾水管压力脉动特性分析与试验[J]. 中南大学学报, 2015, 46(8):3131-3137. DAI Cui, KONG Fanyu, DONG Liang, et al. Analysis and experimental investigation of pressure fluctuation in draft tube of pump as turbine[J]. Journal of Central South University, 2015, 46(8):3131-3137.
[20] 崔宝玲, 许文静, 朱祖超, 等. 低比转速复合叶轮离心泵内的非定常流动特性[J]. 化工学报, 2011, 62(11):3093-3100. CUI Baoling, XU Wenjing, ZHU Zuchao, et al. Unsteady flow characteristics in low-specific-speed centrifugal pump with complex impeller[J]. CIESC Journal, 2011, 62(11):3093-3100.
[21] 施卫东, 杨阳, 周岭, 等. 潜水泵缩比模型的相似性验证与内部流场分析[J]. 农业工程学报, 2017, 33(3):50-57. SHI Weidong, YANG Yang, ZHOU Ling, et al. Verification of comparability and analysis of inner flow fields on scaling models of submersible well pump[J]. Transactions of the Chinese Society of Agricultural Engineering, 2017, 33(3):50-57.
[22] SPALART P R, SHUR M. On the sensitization of turbulence models to rotation and curvature[J]. Aerospace Science&Technology, 1997, 1(5):297-302.
[23] WANG T, KONG F, XIA B, et al. The method for determining blade inlet angle of special impeller using in turbine mode of centrifugal pump as turbine[J]. Renewable Energy, 2017, 109:518-528.
[24] WANG T, WANG C, KONG F, et al. Theoretical, experimental, and numerical study of special impeller used in turbine mode of centrifugal pump as turbine[J]. Energy, 2017, 130:473-485.
[25] CHIRAG T, DAHLHAUG O G. Interaction between trailing edge wake and vortex rings in a francis turbine at runaway condition:Compressible large eddy simulation[J]. Physics of Fluids, 2018, 30(7):75101.
[26] 顾延东, 袁寿其, 裴吉, 等. 泵叶轮出口宽度对蜗壳内压力脉动强度的影响[J]. 哈尔滨工程大学学报, 2017, 38(7):1023-1030. GU Yandong, YUAN Shouqi, PEI Ji, et al. Effects of the outlet width of pump impeller on pressure fluctuation intensity in volute[J]. Journal of Harbin Engineering University, 2017, 38(7):1023-1030.
[27] JI B, LUO X, ARNDT R, et al. Large eddy simulation and theoretical investigations of the transient cavitating vortical flow structure around a NACA66 hydrofoil[J]. International Journal of Multiphase Flow, 2015(68):121-134.
[28] HUANG R, JI B, LUO X, et al. Numerical investigation of cavitation-vortex interaction in a mixed-flow waterjet pump[J]. Journal of Mechanical Science and Technology, 2015, 29(9):3707-3716.

离心泵作透平最佳工况点下的瞬态流动特性分析

Analysis of the Unsteady Flow Characteristics of Chemical Centrifugal Pump as Turbine at the Best Efficiency Point Condition

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	王立新, 张硕研, 闫世兴, 董世运. 猪笼草滑移区微纳复合结构液滴浸润程度的数值模拟[J]. 机械工程学报, 2022, 58(3): 203-212.
[2]	尹立孟, 苏子龙, 左存果, 张中文, 姚宗湘, 王刚, 王善林, 陈玉华. Cu/SAC305/Cu微焊点的剪切蠕变试验及数值模拟[J]. 机械工程学报, 2022, 58(2): 300-306.
[3]	王志远, 邢志国, 王海斗, 单徳彬. 液滴在固体织构化表面上的润湿行为研究现状[J]. 机械工程学报, 2022, 58(1): 124-144.
[4]	赵文勇, 曹熙勇, 杜心伟, 魏艳红, 刘仁培, 陈纪城. CMT电弧增材制造过程传热传质数值模拟[J]. 机械工程学报, 2022, 58(1): 267-276.
[5]	梁伟, 郑颖, 邓德安. 外拘束对铝合金薄板结构焊接变形的影响[J]. 机械工程学报, 2021, 57(6): 70-77.
[6]	尹东杨, 陈晓川, 鲍劲松. 基于磨料水射流的三维编织复合材料铣削技术研究[J]. 机械工程学报, 2021, 57(5): 273-280.
[7]	杜冰, 赵翀昊, 谢军, 李晗, 赵长财, 杜之明. 应力加载路径对板壳塑性起皱失稳极限的影响研究[J]. 机械工程学报, 2021, 57(4): 83-91.
[8]	彭敬辉, 张亚运, 徐阳, 杨睿, 袁立鹏, 李松晶. 基于遗传算法的小型化液压油源用错列翅片式换热器优化研究[J]. 机械工程学报, 2021, 57(24): 49-57.
[9]	姚静, 刘翔宇, 李曼迪, 孔德才, 胡建军. 一种小型化迷宫液压油箱设计与性能分析[J]. 机械工程学报, 2021, 57(24): 83-92.
[10]	杨苑铎, 李洋, 李一昂, 王柏村, 敖三三, 罗震. 碳纤维增强热塑性复合材料超声波焊接研究进展[J]. 机械工程学报, 2021, 57(22): 130-156.
[11]	康娅娟, 刘少军, 姜永明. 多级深海输送电泵叶轮径向不平衡力研究[J]. 机械工程学报, 2021, 57(22): 406-415.
[12]	康娅娟, 刘少军. 深海采矿提升系统研究综述[J]. 机械工程学报, 2021, 57(20): 232-243.
[13]	方玉建, 张敏, 孙先朋, 张金凤, 瞿晔飞. 机械搅拌槽内非牛顿流体内流特性研究[J]. 机械工程学报, 2021, 57(20): 244-253.
[14]	秦国梁, 耿培皓, 陈永, 任文建. 铝/钢异种金属MIG电弧熔-钎焊接界面应力演变数值分析[J]. 机械工程学报, 2021, 57(2): 87-96.
[15]	张嘉, 吴奇. Inconel718微环形零件激光增材制造残余应力数值分析[J]. 机械工程学报, 2021, 57(18): 172-181.