| 逆变焊接电源的离散建模与最少拍控制 |
| |
| 引用本文： | 朱志明,杨中宇,汤莹莹,夏铸亮.逆变焊接电源的离散建模与最少拍控制[J].焊接学报,2016,37(6):19-22,64. |
| |
| 作者姓名： | 朱志明 杨中宇 汤莹莹 夏铸亮 |
| |
| 作者单位： | 1.清华大学 机械工程系, 北京 100084;清华大学 先进成形制造教育部重点实验室, 北京 100084 |
| |
| 基金项目： | 国家自然科学基金资助项目(51075231)；铁道部科技研究开发计划重大资助项目(2008G001－C)；国家科技重大专项资助项目(2012ZX04012011) |
| |
| 摘 要： | 逆变焊接电源所采用的全桥、半桥等功率变换电路可以等效为Buck变换器。在对Buck变换器离散建模的基础上，通过直接时域推导，建立了可用于逆变焊接电源闭环控制的最少拍控制律。所构建的控制算法充分考虑了模型参数与实际参数之间误差的影响。输出滤波电感的变化影响最少拍控制的稳定性和控制效果。稳定条件为模型所用最大电感值不超过实际电感值的1。67倍。结果表明，当模型电感值和实际电感值相等时，系统为最少拍控制。在模型参数和实际负载参数匹配时，系统实现了“没有稳态误差、不存在输出纹波、输出幅值受限”的最少拍控制。
|
| 关 键 词： | 逆变焊接电源 最少拍控制 Buck变换器 离散建模 稳定性分析 |
| 收稿时间： | 2014/8/19 0:00:00 |
Discrete modeling and deadbeat control of inverter welding power supply |
| |
| ZHU Zhiming,YANG Zhongyu,TANG Yingying and XIA Zhuliang.Discrete modeling and deadbeat control of inverter welding power supply[J].Transactions of The China Welding Institution,2016,37(6):19-22,64. |
| |
| Authors: | ZHU Zhiming YANG Zhongyu TANG Yingying and XIA Zhuliang |
| |
| Affiliation: | 1.Department of Mechanical Engineering, Tsinghua University, Beijing 100084, China;Key Lab. for Advanced Materials Processing Technology, Ministry of Education, Tsinghua University, Beijing 100084, China2.Department of Mechanical Engineering, Tsinghua University, Beijing 100084, China |
| |
| Abstract: | Power converters of inverter welding power supply with full-bridge or half-bridge topologies can be equivalent to Buck converter. Based on discrete modeling of Buck converter, the deadbeat control law, which could be applied to the closed-loop control of inverter welding power supply, is established by using direct time-domain derivation. The control algorithm takes a full consideration to the influence of the deviation between model parameters and actual parameters. The stability and control effect of designed deadbeat control are affected by the variation of output filter inductance. The stability condition is that the maximum inductance value used in the model is no more than 1.67 times of the actual inductance value. The simulation results show that, the system is deadbeat control only when the model inductance value equals the actual inductance value; there is no steady-state error, output ripple and overshoot by designed deadbeat control in the matching situation of model parameters and actual load parameters. |
| |
| Keywords: | inverter welding power supply deadbeat control Buck converter discrete modeling stability analysis |
| 本文献已被 CNKI 万方数据 等数据库收录！ |
| 点击此处可从《焊接学报》浏览原始摘要信息 |
|
点击此处可从《焊接学报》下载全文 |
|
