| 加热温度对Al-Si涂层热成形钢组织及性能的影响 |
| |
| 引用本文： | 陈忠.加热温度对Al-Si涂层热成形钢组织及性能的影响[J].金属热处理,2022,47(10):228-233. |
| |
| 作者姓名： | 陈忠 |
| |
| 作者单位： | 中国宝武中央研究院马钢技术中心, 安徽 马鞍山 243002 |
| |
| 摘 要： | 利用粗糙度仪、扫描电镜、硬度计、辉光放电原子发射光谱仪等检测方法,研究分析了热冲压成形工艺过程中的加热温度对Al-Si涂层22MnB5热成形钢组织及性能的影响。结果表明,随着加热温度的升高,Fe沿垂直于表面方向由热成形钢基体向Al-Si涂层表面的迁移量逐渐增大,O沿垂直于表面方向由Al-Si涂层表面向热成形钢基体的迁移量逐渐增大,且迁移的最大深度约为2.80 μm。Fe沿垂直于表面方向由热成形钢基体向Al-Si涂层表面的迁移量直接决定了Fe-Al-Si相的形态、生成位置及界面结合层厚度。随着加热温度的升高,Al-Si涂层表面粗糙度Ra、峰值计数Rpc值先增大后减小;当加热温度为930 ℃时,涂层表面粗糙度Ra达到最大值1.89 μm,峰值计数Rpc值达到最大值218。随着加热温度的升高,Al-Si涂层总厚度从27.78 μm增加至40.46 μm,界面结合层厚度从1.08 μm增加至15.11 μm。当加热温度为930 ℃时,热成形钢基体的硬度达到最大值505 HV0.2。
|
| 关 键 词： | 22MnB5热成形钢 Al-Si涂层 加热温度 元素迁移 组织与性能 |
| 收稿时间： | 2022-04-18 |
Influence of heating temperature on microstructure and properties of hot stamped steel with Al-Si coating |
| |
| Chen Zhong.Influence of heating temperature on microstructure and properties of hot stamped steel with Al-Si coating[J].Heat Treatment of Metals,2022,47(10):228-233. |
| |
| Authors: | Chen Zhong |
| |
| Affiliation: | Masteel Technology Center of China Baowu Central Research Institute, Maanshan Anhui 243002, China |
| |
| Abstract: | Influence of heating temperature during hot stamping process on microstructure and properties of 22MnB5 hot stamped steel with Al-Si coating was researched by means of roughness meter, scanning electron microscope, hardness tester and glow discharge atomic emission spectrometer, respectively. The results indicate that with the increase of heating temperature, the migration amount of Fe from hot stamped steel substrate to coating surface along the direction perpendicular to surface becomes larger gradually. Meanwhile, the migration amount of O from coating surface to hot stamped steel substrate along the direction perpendicular to surface becomes larger gradually, and the maximum migration depth is about 2.80 μm. The migration amount of Fe from hot stamped steel substrate to Al-Si coating surface along the direction perpendicular to surface directly determines the morphology, formation position of Fe-Al-Si phase and interface bonding layer thickness. As the heating temperature rises, the surface roughness Ra and peak count value Rpc of Al-Si coating increase at first, and then decrease; when the heating temperature is 930 ℃, the surface roughness Ra and peak count value Rpc reach maximum values of 1.89 μm and 218, respectively. With the increase of heating temperature, the total thickness of Al-Si coating increases from 27.78 μm to 40.46 μm, the thickness of interface bonding layer increases from 1.08 μm to 15.11 μm. When heating temperature is 930 ℃, the hardness of the hot stamped steel substrate reaches maximum value of 505 HV0.2. |
| |
| Keywords: | 22MnB5 hot stamped steel Al-Si coating heating temperature element migration microstructure and properties |
|
| 点击此处可从《金属热处理》浏览原始摘要信息 |
|
点击此处可从《金属热处理》下载全文 |
|
