| 铜铝复合板渐进成形回弹缺陷研究 |
| |
| 引用本文： | 秦勤,何流,李程,臧勇.铜铝复合板渐进成形回弹缺陷研究[J].中国机械工程,2021,32(3):348. |
| |
| 作者姓名： | 秦勤 何流 李程 臧勇 |
| |
| 作者单位： | 1.北京科技大学机械工程学院，北京，100083
2.北京科技大学顺德研究生院，佛山，520300 |
| |
| 基金项目： | 广东省基础与应用研究基金(2019B1515120070);
北京科技大学顺德研究生院科技创新专项资金(BK19BE009) |
| |
| 摘 要： | 为了讨论不同工艺参数对复合板渐进成形回弹的影响，建立了包含工具头、复合板材和复合界面的三维有限元模型,通过对比T形剥离结果得到复合界面内聚力单元参数，通过实验验证了有限元模型的可靠性。实验结果表明，成形角对双金属复合板渐进成形回弹最敏感，工具头直径对回弹敏感度最低,另外，内聚力单元能有效模拟双金属复合板结合界面，模拟误差仅为7.9%。分析结果表明，单层下压量、板厚、工具头直径都与回弹量成正相关，成形角与回弹量成负相关，成形角从30°增大至60°时回弹量减小21%。
|
| 关 键 词： | 铜铝复合板 渐进成形 有限元分析 内聚力单元 回弹缺陷 |
Research on Springback Defects in Incremental Forming of Cu-Al Bimetal |
| |
| QIN Qin,HE Liu,LI Cheng,ZANG Yong.Research on Springback Defects in Incremental Forming of Cu-Al Bimetal[J].China Mechanical Engineering,2021,32(3):348. |
| |
| Authors: | QIN Qin HE Liu LI Cheng ZANG Yong |
| |
| Affiliation: | 1.School of Mechanical Engineering,University of Science and Technology Beijing,Beijing，100083
2.Shunde Graduate School，University of Science and Technology Beijing,Foshan，Guangdong,520300 |
| |
| Abstract: | In order to discuss the influences of different processing parameters on springback in incremental forming of bimetals, a three-dimensional model was established including the tool head, laminated sheet and composite interface. The parameters of the interface cohesion elements were obtained by comparing the results of T-peeling, and the reliability of the finite element model was verified through experiments. The experimental results show that the forming angle is the most critical factor affecting the springback, and tool diameter is least sensitive to springback. In addition, the cohesive element may effectively simulate the interface of the laminated sheets, and the simulation error is only 7.9%. The analysis shows that the step-down size, sheet thickness and tool diameter are positively related to the springback values, the forming angle is negatively related to the springback ones. And the springback value decreases by 21% as the forming angle increases from 30° to 60°. |
| |
| Keywords: | Cu-Al bimetal incremental forming finite element analysis cohesive element springback defect |
| 本文献已被 CNKI 等数据库收录！ |
| 点击此处可从《中国机械工程》浏览原始摘要信息 |
|
点击此处可从《中国机械工程》下载全文 |
