| 无取向电工钢冶炼过程氧含量控制 |
| |
| 引用本文： | 郭飞虎,仇圣桃,乔家龙,刘磊.无取向电工钢冶炼过程氧含量控制[J].特殊钢,2019,40(4):38-42. |
| |
| 作者姓名： | 郭飞虎 仇圣桃 乔家龙 刘磊 |
| |
| 作者单位： | 1安徽工业大学冶金工程学院，马鞍山243002；
2钢铁研究总院连鮮技术国家工程研究中心，北京100081 |
| |
| 基金项目： | 国家重点研发计划资助(2016YFB0300305) |
| |
| 摘 要： | 无取向硅钢的磁性能与钢的洁净度水平密切相关。为实现对无取向电工钢冶炼过程氧含量的合理控制,分析了无取向电工钢冶炼过程碳氧含量变化数据,热力学计算转炉终点临界碳含量与炉渣αFeO。结果表明:随着转炉终点碳含量的降低,终点氧含量升高且波动范围大,合理出钢碳含量应控制为0.03%～0.05%;为满足炉渣中T.Fe≤24%的现场生产要求,终点碳含量应高于0.031%;钢包底吹氩气可有效降低钢液中过剩氧,降低钢液的平均碳氧积;据现场生产数据,RH精炼前理想碳、氧含量应控制为0.025%～0.035%和500×10-6～650×10-6,相应转炉终点碳含量控制为0.03%～0.04%。
|
| 收稿时间： | 2019-03-15 |
Controlling Oxygen in Steelmaking Process of Non-Oriented Electrical Steel |
| |
| Guo Feihu,Qiu Shengtao,Qiao Jialong,Liu Lei.Controlling Oxygen in Steelmaking Process of Non-Oriented Electrical Steel[J].Special Steel,2019,40(4):38-42. |
| |
| Authors: | Guo Feihu Qiu Shengtao Qiao Jialong Liu Lei |
| |
| Affiliation: | 1 College of Metallurgical Engineering, Anhui University of Technology, Ma'anshan 243002 ；
2 Engineering and Research Center for Continuous Casting Technology, Central Iron and Steel Research Institute, Beijing 100081 |
| |
| Abstract: | Abstract The magnetic properties of non-oriented electrical steels are closely related to the cleanliness level. In order to achieve reasonable control of oxygen in non-oriented electrical steel smelting process,the change of carbon and oxygen content were analyzed, the critical carbon content at the end-point of BOF and αFeO in slag were also calculated. The results show that with the decrease of end-point carbon content, the end-point oxygen content increases and fluctuates widely. The ideal carbon content in tapping should be controlled at 0. 03% ~0. 05%. It is required that the content of T. Fe in slag should be ≤ 24% and the end-point carbon content should be higher than 0.031%. Ladle botton argon blowing can effectively reduce excess oxygen and decrease carbon-oxygen product in molten steel. According to production data, the ideal carbon and oxygen content should be controlled at 0.025% ~0. 035% and 500 X 10-6 ~650 X 10-6 before RH refining, and the end-point carbon content of BOF should be controlled at 0.03% ~0.04%. |
| |
| Keywords: | |
| 本文献已被 CNKI 等数据库收录！ |
| 点击此处可从《特殊钢》浏览原始摘要信息 |
|
点击此处可从《特殊钢》下载全文 |
|
