| 筒形件冷挤压凹模强度设计及结构优化 |
| |
| 引用本文： | 鲁志兵,王成勇,张心怡,张鹏,王思艳,王源.筒形件冷挤压凹模强度设计及结构优化[J].中国机械工程,2015,26(23):3228-3233. |
| |
| 作者姓名： | 鲁志兵 王成勇 张心怡 张鹏 王思艳 王源 |
| |
| 作者单位： | 合肥工业大学,合肥,230009 |
| |
| 基金项目： | 国家自然科学基金资助项目（51275146）；教育部科学研究重大项目（311025）；安徽省自然科学基金资助项目(1208085ME71)；留学回国人员科研启动基金资助 |
| |
| 摘 要： | 基于厚壁圆筒理论,分析了整体式凹模工作载荷特点，讨论了单纯通过增加壁厚来提高模具强度的局限性。为提高承载能力，探讨了多层预应力组合凹模方案。基于第四强度理论，推导了n层组合凹模承受内压的数学表达式。采用Lagrange乘子法对组合凹模参数进行了优化设计,推导了n层组合凹模各层最佳径比分配、凹模极限内压、套缩界面残余压力及最优过盈量等设计变量的计算式。以三层组合凹模为算例，运用理论分析和数值模拟相结合的方法，对上述n层组合凹模的各设计变量计算式进行了验证，结果表明两者的结果吻合较好。
|
| 关 键 词： | 挤压凹模 强度设计 结构优化 Lagrange乘子法 |
Strength Design and Structural Optimization of Cold Extrusion Die for Cylindrical Workpieces |
| |
| Lu Zhibing,Wang Chengyong,Zhang Xinyi,Zhang Peng,Wang Siyan,Wang Yuan.Strength Design and Structural Optimization of Cold Extrusion Die for Cylindrical Workpieces[J].China Mechanical Engineering,2015,26(23):3228-3233. |
| |
| Authors: | Lu Zhibing Wang Chengyong Zhang Xinyi Zhang Peng Wang Siyan Wang Yuan |
| |
| Affiliation: | Hefei University of Technology,Hefei,230009 |
| |
| Abstract: | Based on the theories of thick-walled cylinder, the mechanical characteristics of integral die under working conditions were analyzed and the calculation results show that it is difficult to increase the die strength only by increasing the wall thickness. In order to improve the load supporting capacity of the die, the scheme of prestressed multilayer the die was discussed. Based on the fourth failure criteria,a mathematical expression of n-layer combinatorial die under internal pressure was deduced. Lagrange multiplier method was used to obtain the optimum design parameters of combinatorial die. The design formulas of optimum diameter ratio of each layer, the limit loading pressure，the residual pressure in shrinkage interface and optimum radial magnitude of interference were investigated. Through the optimum design of three-layer combinatorial die, the derived formulas was verified using two methods of theoretical analysis and numerical simulation.The investigation shows that the simulation results are consistent with the theoretical ones. |
| |
| Keywords: | extrusion die strength design structure optimization Lagrange multiplier method |
| 本文献已被 CNKI 等数据库收录！ |
| 点击此处可从《中国机械工程》浏览原始摘要信息 |
|
点击此处可从《中国机械工程》下载全文 |
|
