Control of Microstructure and Orientation in Solution-Deposited BaTiO3 and SrTiO3 Thin Films

Columnar and highly oriented (100) BaTiO₃ and SrTiO₃ thin films were prepared by a chelate-type chemical solution deposition (CSD) process by manipulation of film deposition conditions and seeded growth techniques. Randomly oriented columnar films were prepared on platinum-coated Si substrates by a multilayering process in which nucleation of the perovskite phase was restricted to the substrate or underlying layers by control of layer thickness. The columnar films displayed improvements in dielectric constant and dielectric loss compared to the fine-grain equiaxed films that typically result from CSD methods. Highly oriented BaTiO₃ and SrTiO₃ thin films were fabricated on LaAlO₃ by a seeded growth process that appeared to follow a standard "two-step" growth mechanism that has been previously reported. The film transformation process involved the bulk nucleation of BaTiO₃ throughout the film, followed by the consumption of this matrix by an epitaxial overgrowth process originating at the seed layer. Both BaTiO₃ and PbTiO₃ seed layers were effective in promoting the growth of highly oriented (100) BaTiO₃ films. Based on the various processing factors that can influence thin film microstructure, the decomposition pathway involving the formation of BaCO₃ and TiO₂ appeared to dictate thin film microstructural evolution.     

Synthesis of Micron-Scale Platelet BaTiO3

Micron-scale platelet barium titanate was synthesized using a twostep molten salt and topochemical technique. Plate-like BaBi₄Ti₄O₁₅ was first synthesized as a precursor by molten salt synthesis. Then, Bi³⁺ in the precursor was replaced by Ba²⁺ and formed perovskite-structure BaTiO₃ through a topochemical reaction. The BaTiO₃ single crystals have an average size of 5–10 μm and a thickness of 0.5 μm. The purpose of this article is to control the particle shape with desired structure. High aspect ratio BaTiO₃ platelets are suitable templates to obtain textured ceramics (especially Pb(Mg_1/3Nb_2/3)O₃–32.5PbTiO₃) by the templated grain growth process.     

Hydrothermal Processing of PbTiO3 and PbTiO3/Polymer Thin Films from Titanium Metallo-organic Precursors

PbTiO₃ and PbTiO₃/polymer thin films were synthesized from metallo-organic precursors on metallized quartz substrates. Titanium dimethoxy dineodecanoate (TDD) was spin-cast onto the substrates and converted to polycrystalline TiO₂ via hydrolysis in deionized water for 5 h at 80°C. Polycrystalline PbTiO₃ films were then formed by reacting the TiO₂ films for 4 h at 200°C in aqueous solutions of KOH and Pb(CH₃COO)₂·3H₂O. Low KOH concentrations suppressed film coarsening, thereby facilitating the formation of fine-grain continuous PbTiO₃ films. PbTiO₃/polymer thin films were processed as above after first dissolving TDD and a polystyrene/polybutadiene block copolymer in p -xylene. PbTiO₃ and PbTiO₃/polymer films had relative permittivities of ≈56 and 34 and dielectric strengths of ≈250 and 850 kV/cm, respectively.     

Interfacial Reaction of BaTiO3 Ceramics with PbO–B2O3 Glasses

Interfacial reactions of pure, lead-, and zirconium-substituted BaTiO₃ ceramics with PbOB₂O₃ glasses were studied, with an emphasis on the effect of glass composition. Microstructures were analyzed by scanning electron microscopy and electron-probe microanalysis aided with X-ray diffractometry of powder mixtures in the system BaTiO₃PbOB₂O₃ heated at 850°C. The interfacial microstructures were divided into two types, depending on the glass composition. The first type was characterized by precipitates of TiO₂ dispersed in the glass matrix. Extended heating or limited glass volume resulted in the formation of a continuous layer of BaTi(BO₃)₂. The second type of microstructure was characterized by a lead-rich perovskite phase, which developed at the glass/ceramic interfacial region. Growth kinetics for this phase denied the diffusion-controlled mechanism. The substitution of lead in BaTiO₃ enhanced the penetration of glass into the ceramics along the grain boundaries and developed a coreshell structure.     

Grain-Boundary Migration and Dielectric Properties of Semiconducting SrTiO3 in the SrTiO3-BaTiO3-CaTiO3 System

Chemically induced grain-boundary migration and its effects on the interface and dielectric properties of semiconducting SrTiO₃ have been investigated. Strontium titanate specimens that had been doped with 0.2 mol% of Nb₂O₅ were sintered in 5H₂/95N₂. The sintered specimens were diffusion annealed at 1400°C in 5H₂/95N₂ with BaTiO₃ or 0.5BaTiO₃-0.5CaTiO₃ (mole fraction) packing powder. The grain boundaries of the annealed specimens were oxidized in air. In the case of BaTiO₃ packing, grain-boundary migration occurred with the diffusion of BaTiO₃ along the grain boundary. The effective dielectric constant of the specimen decreased gradually as the temperature increased but showed two peaks, possibly because of barium enrichment at the grain boundary and an oxidized Sr(Ba)TiO₃ layer. In the case of 0.5BaTiO₃-0.5CaTiO₃ packing, although barium and calcium were present at the grain boundary of the specimen, no boundary migration occurred, as in a previous investigation. With the diffusion of barium and calcium, the resistivity of the specimen increased and the variation of the effective dielectric constant with temperature was much reduced, in comparison to those without solute diffusion. These enhanced properties were attributed to the solute enrichment and the formation of a thin diffusional Sr(Ba,Ca)TiO₃ layer at the grain boundary.     

Formation of BaTiO3 from BaCO3 and TiO2 in Air and in CO2

The formation of BaTiO₃ from equimolar BaCO₃ and TiO₂ (rutile) mixtures was studied in air and in CO₂. A small amount of BaTiO₃ is formed first directly from BaCO₃ and TiO₂ at the surface of contact. From then on it is a diffusion-controlled reaction, and both BaTiO₃ and Ba₂TiO₄ are produced, with Ba₂TiO₄ being formed in much larger amounts. In 1 atmosphere of CO₂, the intermediate Ba₂TiO₄ was suppressed up to a temperature of about 1100°C. in agreement with thermodynamic calculations. Ba₂TiO₄ reacts fast with 1 atmosphere of CO₂ below about 1100°C. to produce BaTiO₃and BaCO₃     

Phase Transitions in the System BaTiO3—KnbO3

Solid solution formation in the system BaTiO₃—KnbO₃ was established by X-ray diffraction and dielectric measurements. Solid solutions with cubic symmetry were observed in the composition range from 4 to 90 mole % KnbO₃ at room temperature. The lattice parameter for the BaTiO₃ solid solutions increased with increasing KNbO₃; that for the KnbO₃ solid solutions decreased with the addition of BaTiO₃. A distinct discontinuity in lattice parameter was observed at the composition containing about 65 mole % BaTiO₃. Dielectric measurements were made from-195° to 400°C. The cubic-tetragonal transition temperature of BaTiO₃ was rapidly lowered with increasing addition of KNbO₃, whereas the two lower phase transition temperatures were raised. All three phase transitions of KnbO₃ were rapidly lowered with increasing addition of BaTiO₃. The observed phase transitions, lattice parameters, and electron probe data suggest a complex region in the subsolidus which extends from 35 to about 75 mole % KNbO₃.     

Electroceramics from Source Materials via Molecular Intermediates: PbTiO3 from TiO2 via [Ti(catecholate)3]2-

The precursor [NH₄]₂[Ti(catecholate)₃] · 2H₂O is known to react with Ba(OH)₂· 8H₂O in an acid/base process that generates Ba[Ti(catecholate)₃] · 3H₂O, a compound which undergoes low-temperatue calcination to produce BaTiO₃ powder. Attempts to develop similar routes to PbTiO₃ have been frustrated, since lead(II) hydroxide does not exist. The amphoteric yellow PbO and the basic oxide, Pb₆O(OH)₆⁴⁺, are both insufficiently basic to react with [NH₄]₂[Ti(catecholate)₃] · 2H₂O. Based on the large sizes of both the [Ti(catecholate)₃]^2- anion and the Pb²⁺ cation, a precipitation method has been developed in which lead nitrate and [NH₄]₂[Ti(catecholate)₃] · 2H₂O are added together in an aqueous medium causing precipitation and leaving only NH₄NO₃ in solution. The lead-titanium-catecholate complex that forms in this manner undergoes low-temperature pyrolysis to produce PbTiO₃. SEM indicates a submicrometer ultimate crystallite size.     

High Tc in Electrospun BaTiO3 Nanofibers

BaTiO₃ nanofibers were prepared by electrospinning. The morphology of synthesized BaTiO₃ nanofibers was investigated under different heat treatment conditions. The phase transformations in BaTiO₃ nanofibers were monitored using Raman spectroscopy. It has been found that the Curie temperature of BaTiO₃ nanofibers increased to 220°C, which is notably higher than the bulk BaTiO₃ ceramics.     

Analysis of Ferroelectric Domain Switching in 0.7Pb(Mg1/3Nb2/3)O3·0.3PbTiO3: Heterogeneous Nucleation

Polarization reversal and domain dynamics were investigated in 0.7Pb(Mg_1/3Nb_2/3)O₃·0.3PbTiO₃ using a method of current transients. Investigations were performed as a function of applied electric field. The kinetics of the transients were modeled to a stretched exponential-type function.     

Perovskite Formation and Dielectric Characteristics of Pb(Zn1/3Ta2/3)O3 with PbTiO3 Substitution

Perovskite developments in the Pb(Zn_1/3Ta_2/3)O₃–PbTiO₃ system were explored. Formation yields and lattice parameters of the perovskite were determined from X-ray diffractometry results. Weak-field low-frequency dielectric properties of the system ceramics were investigated, followed by microstructure examination. Perovskite started to develop in Pb(Zn_1/3Ta_2/3)O₃ after the introduction of 30 mol% PbTiO₃, whereas complete stabilization was accomplished at 60% substitution. Dielectric relaxation behavior was not substantial across the entire composition range, whereas phase transition modes changed from diffuse to sharp with increased PbTiO₃ fraction.     

Conversion of SiO2 Diatom Frustules to BaTiO3 and SrTiO3

Diatom frustules were used as bio-templates to synthesize functional ceramics via solid–gas displacement reactions. Silica-based frustules were exposed to TiF₄ at 330°C to form TiOF₂, which was later converted to TiO₂ (anatase) by heat treatment in air at 600°C. The TiO₂ frustules were then exposed to molten Ba(OH)₂ or Sr(OH)₂ to form BaTiO₃ or SrTiO₃, respectively. In both cases, near-complete conversion was achieved while retaining the morphology of the original silica frustules. BaTiO₃ and SrTiO₃ frustules exhibit nearly phase pure, nanocrystalline perovskite structure.     

Melting and Interface Reaction of Mn–Si–O Glass on BaTiO3

A glass with the eutectic composition 3MnO_1.5–2SiO₂ was used to simulate the formation of a liquid phase during sintering of BaTiO₃. Two oxide additives (Mn₂O₃ and SiO₂) performing various functions of the properties of BaTiO₃ were investigated for their crystallization and thermal characteristics at temperatures ≤1400°C. The wetting behavior of the glass, the dissolution of BaTiO₃ in glass melt, the identification of newly formed phases, and the sequential reaction kinetics of the glass/BaTiO₃ system, especially when isothermally treated at 1150°C, were investigated by electron microscopy with quantitative X-ray energy dispersive spectroscopic (Q-EDS) analysis. The evolution of the interfacial reaction of the glass/BaTiO₃ at 1150°C is reported and discussed.     

Effects of Sm2O3 and Gd2O3+ Nd2O3 on Electromechanical Properties of PbTiO3 Ceramics

The electromechanical properties of PbTiO₃ ceramics, modified by substitution of Sm or Gd + Nd (same average atomic radius as Sm) for Pb, were studied in the range of 6% to 14% substitution. The modified PbTiO₃ ceramics were stable, and the Curie temperature decreased linearly over this composition range. The 10% Sm composition had a large anisotropy in the coupling factor ratio, k _t / k _p , and a similar, but weaker, effect developed for 12% (1/2 Gd + 1/2 Nd). This indicates that other than average ion size may influence the electromechanical coupling factor ratio.     

Electromechanical Properties of Pb(Yb1/2Nb1/2)O3-PbZrO3-PbTiO3 Ceramics

The electromechanical and electric-field-induced strain properties of x Pb(Yb_1/2Nb_1/2)O₃· y PbZrO₃·(1− x − y )PbTiO₃ ( x = 0.12, 0.25, 0.37; y = 0.10–0.40) ceramics have been studied systematically as a function of Pb(Yb_1/2Nb_1/2)O₃ (PYN) content and PbZrO₃/PbTiO₃ (PZ/PT) ratio. In addition, the effect of MnO₂ on the electromechanical properties of 0.12Pb(Yb_1/2Nb_1/2)O₃·0.40PbZrO₃·0.48PbTiO₃ was also investigated. The maximum transverse strain values of 1.6 × 10⁻³ for x = 0.12, 1.45 × 10⁻³ for x = 0.25, and 1.36 × 10⁻³ for x = 0.37 were obtained at the compositions which were regarded as the morphotropic phase boundary (MPB). The transverse strain was maximized at the MPB composition. The value of the maximum electromechanical coupling coefficient was 0.69 for y = 0.40 and x = 0.12 composition. In the 0.12Pb(Yb_1/2Nb_1/2)O₃·0.40PbZrO₃·0.48PbTiO₃ composition, the temperature of the maximum dielectric constant decreased and the grain size increased with an addition of MnO₂. The electromechanical coupling coefficient decreased while the mechanical quality factor rapidly increased with an addition of MnO₂. These resulted mainly from the acceptor effect of manganese ions that were produced by doping MnO₂ into the perovskite structure.     

Reverse Micellar Route to Nanocrystalline Titanates (SrTiO3, Sr2TiO4, and PbTiO3): Structural Aspects and Dielectric Properties

Nanoparticles of strontium titanates (SrTiO₃, Sr₂TiO₄) and lead titanate (PbTiO₃) have been obtained using reverse micelles as nanoreactors. Powder X-ray diffraction studies of the powders after calcining at 800°C show monophasic SrTiO₃, Sr₂TiO₄, and PbTiO₃. X-ray line broadening studies and transmission electron microscopic studies show spherical grains of 30–40 nm size for strontium titanates, while PbTiO₃ is obtained in the form of nanorods. The dielectric constant of SrTiO₃ and Sr₂TiO₄ is found to be 90 and 30, respectively, (at 100 kHz) for samples sintered at 1000°C. PbTiO₃ shows a dielectric constant of 160 (at 100 kHz) after sintering at 900°C. The dielectric constant of Sr₂TiO₄ (with temperature) is highly stable. The temperature variation studies of the dielectric constant of PbTiO₃ show a ferroelectric phase transition at 490°C (1 kHz). The T _c varies with frequency and is found to decrease to 470°C at 100 kHz.     

Synthesis of Nano-sized BaTiO3 Powders by the Rotary-Hydrothermal Process

Nano-sized BaTiO₃ powders with narrow size distribution and high tetragonality were attempted to be synthesized by the rotary-hydrothermal process in a water system as a novel technique, using a mixture of anatase-type TiO₂ and Ba(OH)₂ as starting material. The rotary-hydrothermal syntheses were performed under conditions with a rotary-speed of 20 revolutions per minute at 423–523 K for 3–96 h. Highly- and mono-dispersed BaTiO₃ powders mainly composed of coarse-faceted particles with the tetragonal phase were successfully synthesized by controlling the conditions for rotary-hydrothermal treatments. TEM and TG results revealed that these coarse-faceted BaTiO₃ particles contained very few structural defects such as hydroxyl content. Thus, the rotary-hydrothermal process was a useful method to synthesize very high-quality BaTiO₃ particles, and the further control of various conditions of the rotary-hydrothermal treatment is expected to control the crystalline phase and microstructures of final BaTiO₃ powders.     

Effect of Ba6Ti17O40/BaTiO3 Interface Structure on {111} Twin Formation and Abnormal Grain Growth in BaTiO3

A structural transition of Ba₆Ti₁₇O₄₀/BaTiO₃ interfaces from faceted to rough was induced by reducing oxygen partial pressure in the atmosphere. As the oxygen partial pressure decreased, the number densities of {111} twins and abnormal grain decreased. TEM observation showed that the twin formation was governed only by the faceting of the interface. Experimental evidence of {111} twin-assisted abnormal growth of faceted BaTiO₃ grains was also obtained.     

Formation of Core-Shell Structure in the BaTiO3-SrTiO3 System

When a 1-mol%-Fe₂O₃-added 0.67BaTiO₃-0.33SrTiO₃ (mole ratio) powder compact was sintered at 1380°C, a core-shell structure was developed. The core phase formed via solid-state interdiffusion of barium and strontium ions between BaTiO₃ and SrTiO₃ particles. In contrast, the shell phase formed via a solution-precipitation process in the presence of an Fe₂O₃-containing liquid phase. Energy-dispersive X-ray analysis showed that the core was a strontium-rich paraelectric phase and the shell was a barium-rich ferroelectric phase at room temperature. The core-shell structure developed in the BaTiO₃-SrTiO₃ system suggests the possibility of obtaining a variety of phase distributions with different Curie temperatures.     

Effects of Ba6Ti17O40 on the Dielectric Properties of Nb-Doped BaTiO3 Ceramics

The dielectric properties, including the DC breakdown strength, of 1 mol% Nb⁵⁺-doped BaTiO₃ ceramics with different quantities of excess TiO₂ have been investigated. The breakdown strength was found to decrease with increasing TiO₂ content, but could not be readily explained by relative density and grain size effects. The decrease in the breakdown strength from a stoichiometric BaTiO₃ composition to samples with excess TiO₂ is believed to be due to the field enhancement effect (up to a factor of 1.40) at the BaTiO₃ matrix because of the presence of a Ba₆Ti₁₇O₄₀ second phase. The thermal expansion coefficient mismatch between the BaTiO₃ matrix phase and the Ba₆Ti₁₇O₄₀ phase may also result in a low breakdown strength. The dielectric properties of the pure Ba₆Ti₁₇O₄₀ phase were also investigated and are reported herein.