共查询到20条相似文献,搜索用时 144 毫秒
1.
2.
橡胶密封是中低压阀门的主要软密封形式,介绍了供水阀门用橡胶密封件的材料要求、检验方法、贮存运输和安装使用。 相似文献
3.
阀门水压试验用检漏阀开封高压阀门厂魏成杰,关书训阀门水压试验用检漏阀(图)由阀体、阀芯、导管和O形图组成。在使用时,将该间安装在被测阀门的侧端盖上,从另一侧向被测阀门供水和施压。在供水时,可将检漏阀开启,排出被测阀门体腔内的空气。待水满后,关闭检漏间... 相似文献
4.
5.
6.
介绍了对阀门外载荷弯曲试验原理、试验方法以及载荷参数选取与统计分析的研究,给出了阀门外载荷弯曲试验模型和参数,提供了评定管线阀门承受外载荷可靠性依据。 相似文献
7.
多功能水泵控制阀能帮助泵站实现自动化控制、降低操作强度、减少维护成本,阐述了多功能水泵控制阀的结构、工作原理,介绍了此类阀门在供水泵站的使用情况及效果,指出了该阀门在水泵站的应用前景。 相似文献
8.
9.
10.
在机组正常运行时,要定期进行阀门活动性能试验,以防止发生阀门卡涩、阀碟与阀座抱死现象,文中介绍了阀门活动性能试验的方法和实验要求. 相似文献
11.
12.
为实现对氮气式水击泄压阀的功能和关键性能进行充分研制试验,设计并搭建了一种能够满足工作压力高、流量大等试验条件的液流试验平台,并在试验过程中设计了包含设定压力、响应时间和设定压力误差试验在内的四项试验验证方法。根据所设计方法分别对型号为200YXY-100D的氮气式水击泄压阀主阀在氮气腔压力为1,2,3,4,5 MPa工况下试验平台进行验证试验。结果表明所设计液流试验平台和试验方法能够充分验证氮气式水击泄压阀和氮气供应系统结构强度、密封性能、动作可靠性和整阀系统的可靠性。 相似文献
13.
针对双泵并联给水回路系统,通过结构简化和假设,建立了水锤计算的基本方程和合理的数学物理模型。构造求解边界条件,利用特征线方法编制水锤计算程序,对双泵切换条件下的水锤现象进行分析计算。研究结果表明,止回阀在关闭过程中阀瓣与阀座出现了剧烈的碰撞现象,系统管路出现了较为剧烈的水锤压力波振荡,两台泵交替时管道压力波动幅度最大。 相似文献
14.
15.
16.
根据国内外钢制闸阀的有关标准,从压力和温度额定值、最小壁厚、阀盖与阀体中法兰连接、阀门密封副、接口尺寸有阀门的检验与试验等几方面进行了分析比较。 相似文献
17.
分析了高压阀门阀体和阀盖的连接形式及其相关标准的规定。提出了石油化工用阀门阀体和阀盖采用压力自紧密封结构连接形式应注意的问题和避免阀门泄漏的辅助措施。 相似文献
18.
Farid Vakili-Tahami Mohammad Zehsaz Mahdi Mohammadpour Ali Vakili-Tahami 《Journal of Mechanical Science and Technology》2012,26(9):2799-2806
Butterfly valves are widely used in various industries such as water distribution, sewage, oil and gas plants. The hydrodynamic torque applied on the butterfly valve disk is one of the most important factors which should be considered in their design and application. Although several methods have been used to calculate the total torque on these valves, most of them are based on hydrostatic analysis and ignore the hydrodynamic effect which has a major role to determine the torque of the large-size valves. For finding the dynamic-valvetorque, some empirical formulas and methods have been proposed; for example in AWWA C504 standard, a relationship for calculating the dynamic torque has been given and its variation versus disk angle has been stated. However, the use of these empirical relationships is restricted due to the conditions defined in the standards. In this paper, the dynamic-valve-torque has been calculated for a large butterfly valve under different conditions and also at the different opening angles of the valve disk. For this purpose a computational fluid dynamics (CFD) method has been used. The results have been compared with those given in the AWWA C504 standard recommendations. Moreover, the effects of the disk shape and its deformation, surface roughness, upstream/downstream pressure variation and disk-offset value have been studied. 相似文献
19.
20.