Implantation effect of diamond-like carbon films by 110 keV nitrogen ions

Diamond-like carbon films, grown on microscope slides by a dual-ion beam sputtering system, were implanted by 110 keV N⁺ under the doses of 1 × 10¹⁵, 1 × 10¹⁶ and 1 × 10¹⁷ions cm⁻² respectively. The implantation induced changes in electrical resistivity of the films and in infrared (IR) transmittance of the specimens were investigated as a function of implantation dose. The structural changes of the films were also studied using IR spectroscopy and Raman spectroscopy. It was observed that, with the increase of implantation dose, the diamond-like carbon films display two different stages in electrical and optical behaviours. The first is the increase of both the film resistivity and the IR transmittance of specimen at the dose of 1 × 10¹⁵ ions cm⁻² which, we consider, is attributed to the implantation-induced increase sp³ C---H bonds. However, when the doses are higher than 1 × 10¹⁵ ions cm⁻², the film resistivity and the IR transmittance of specimen decrea significantly and the decrease rates at dose range of 1×10¹⁶ to 1×10¹⁷ ions cm⁻² are smaller than those between 1×10¹⁵ and 1 × 10¹⁶ ions cm⁻². We conclude that the significant reductions of the two parameters at high doses are caused by the decreases of bond-angle disorder and of sp³ C---H bonds, the increases of sp² C---C bonds dominated the crystallite size and/or number and also the sp² C---H bonds. The smaller decrease rates at a dose range of 1 × 10¹⁶ to 1 × 10¹⁷ ions cm⁻² may be caused by further recombination of some retained hydrogen atoms to carbon atoms.     

Electrical characterization of CVD diamond thin films grown on silicon substrates

Diamond thin films grown on high resistivity, 100 oriented silicon substrates by the hot filament chemical vapor deposition (HFCVD) method have been characterized by four-point probe and current-voltage (through film) techniques. The resistivities of the as-grown, chemically etched and annealed samples lie in the range of 10² Ω cm to 10⁸ Ω cm. The Raman measurements on these samples indicate sp³ bonding with a sharp peak at 1332 cm⁻¹. The surface morphology as determined by scanning electron microscope shows polycrystalline films with (100) or (111) faceted structures with average grain size of ≈2.5 μm. The through film current-voltage characteristics obtained via indium contacts on these diamond films showed either rectifying or ohmic behavior. The difference in Schottky and ohmic behavior is explained on the basis of the high or low sheet resistivities measured by four-point probe technique. 5% methane to hydrogen concentration during film growth resulted in poor surface morphology, absence of sp³ bonds, and low resistivity.     

Optically active Er–Yb codoped Y2O3 films produced by pulsed laser deposition

Optically active Er³⁺:Yb³⁺ codoped Y₂O₃ films have been produced on c-cut sapphire substrates by pulsed laser deposition from ceramic Er:Yb:Y₂O₃ targets having different rare-earth concentrations. Stoichiometic films with very high rare-earth concentrations (up to 5.5 × 10²¹ at cm^− 3) have been achieved by using a low oxygen pressure (1 Pa) during deposition whereas higher pressures lead to films having excess of oxygen. The crystalline structure of such stoichiometric films was found to worsen the thicker the films are. Their luminescence at 1.53 μm and up-conversion effects have been studied by pumping the Yb³⁺ at 0.974 μm. The highest lifetime value (up to 4.6 ms) is achieved in films having Er concentrations of ≈ 3.5 × 10²⁰ at cm^− 3 and total rare-earth concentration ≈ 1.8 × 10²¹ at cm^− 3. All the stoichiometric films irrespective of their rare-earth concentration or crystalline quality have shown no significant up-conversion.     

Dielectric properties of AlN films prepared by laser-induced chemical vapour deposition

The dielectric properties and electrical conductivity of AlN films deposited by laser-induced chemical vapour deposition (LCVD) are studied for a range of growth conditions. The static dielectric constant is 8.0 ± 0.2 over the frequency range 10²−10⁷ Hz and breakdown electric fields better than 10⁶ V cm⁻¹ are found for all films grown at temperatures above 130°C. The resistivity of the films grown under optimum conditions (substrate temperature above 170°C, NH₃/TMA flow rate ratio greater than 300 and a deposition pressure of 1–2 Torr) is about 10¹⁴ Ω cm and two conduction mechanisms can be identified. At low fields, F < 5 × 10⁵ V cm⁻¹ and conductivity is ohmic with a temperature dependence showing a thermal activation energy of 50–100 meV, compatible with the presumed shallow donor-like states. At high fields, F > 1 × 10⁶ V cm⁻¹, a Poole-Frenkel (field-induced emission) process dominates, with electrons activated from traps at about 0.7–1.2 eV below the conduction band edge. A trap in this depth region is well-known in AlN. At fields between 4 and 7 × 10⁵ V cm⁻¹ both conduction paths contribute significantly. The degradation of properties under non-ideal growth conditions of low temperature or low precursor V/III ratio is described.     

The optical and electrical properties of copper indium di-selenide thin films

Thin films of copper indium di-selenide (CIS) with a wide range of compositions near stoichiometry have been formed on glass substrates in vacuum by the stacked elemental layer (SEL) deposition technique. The compositional and optical properties of the films have been measured by proton-induced X-ray emission (PIXE) and spectrophotometry (photon wavelength range of 300–2500 nm), respectively. Electrical conductivity (σ), charge-carrier concentration (n), and Hall mobility (μ_H) were measured at temperatures ranging from 143 to 400 K. It was found that more indium-rich films have higher energy gaps than less indium-rich ones while more Cu-rich films have lower energy gaps than less Cu-rich films. The sub-bandgap absorption of photons is minimum in the samples having Cu/In ≈ 1 and it again decreases, as Cu/In ratio becomes less than 0.60. Indium-rich films show n-type conductivities while near-stoichiometric and copper-rich films have p-type conductivities. At 300 K σ, n and μ_H of the films vary from 2.15 × 10⁻³ to 1.60 × 10⁻¹ (Ω cm)⁻¹, 2.28 × 10¹⁵ to 5.74 × 10¹⁷ cm⁻³ and 1.74 to 5.88 cm² (V s)⁻¹, respectively, and are dependent on the composition of the films. All the films were found to be non-degenerate. The ionization energies for acceptors and donors vary between 12 and 24, and 3 and 8 meV, respectively, and they are correlated well with the Cu/In ratios. The crystallites of the films were found to be partially depleted in charge carriers.     

Infrared optical properties of Bi2Ti2O7 thin films by spectroscopic ellipsometry

Bi₂Ti₂O₇ thin films have been grown directly on n-type GaAs (1 0 0) by the chemical solution decomposition technique. X-ray diffraction analysis shows that the Bi₂Ti₂O₇ thin films are polycrystalline. The optical properties of the thin films are investigated using infrared spectroscopic ellipsometry (3.0–12.5 μm). By fitting the measured ellipsometric parameter (Ψ and Δ) data with a three-phase model (air/Bi₂Ti₂O₇/GaAs), and Lorentz–Drude dispersion relation, the optical constants and thickness of the thin films have been obtained simultaneously. The refractive index and extinction coefficient increase with increasing wavelength. The fitted plasma frequency ω_p is 1.64×10¹⁴ Hz, and the electron collision frequency γ is 1.05×10¹⁴ Hz, and it states that the electron average scattering time is 0.95×10⁻¹⁴ s. The absorption coefficient variation with respect to increasing wavelength has been obtained.     

Structural properties of swift heavy ion beam irradiated Fe/Si bilayers

The Fe/Si multilayers were prepared by electron beam evaporation in a cryo-pumped vacuum deposition system. Ag⁺ and Au⁺ ions of 100 MeV at two different fluencies such as 1 × 10¹² ions/cm² and 1 × 10¹³ ions/cm² at a pressure of 10^− 7 torr were used to irradiate the Fe/Si samples. The irradiated samples were analyzed by High-Resolution XRD and it reveals that the irradiated films are having polycrystalline nature and it confirms the formation of the β-FeSi₂. The structural parameters such as crystallite size (D), strain (ε) and dislocation density (δ) have been evaluated from the XRD spectrum. The role of the substrates and the influence of swift heavy ions on the formation of β-FeSi₂ have been discussed in this paper.     

Atomic layer deposition growth of zirconium doped In2O3 films

Zirconium doped indium oxide thin films were deposited by the atomic layer deposition technique at 500 °C using InCl₃, ZrCl₄ and water as precursors. The films were characterised by X-ray diffraction, energy dispersive X-ray analysis and by optical and electrical measurements. The films had polycrystalline In₂O₃ structure. High transparency and resistivity of 3.7×10⁻⁴ Ω cm were obtained.     

Highly conducting doped poly-Si deposited by hot wire CVD and its applicability as gate material for CMOS devices

Highly conducting p- and n-type poly-Si:H films were deposited by hot wire chemical vapor deposition (HWCVD) using SiH₄+H₂+B₂H₆ and SiH₄+H₂+PH₃ gas mixtures, respectively. Conductivity of 1.2×10² (Ω cm)⁻¹ for the p-type films and 2.25×10² (Ω cm)⁻¹ for the n-type films was obtained. These are the highest values obtained so far by this technique. The increase in conductivity with substrate temperature (T_s) is attributed to the increase in grain size as reflected in the atomic force microscopy results. Interestingly conductivity of n-type films is higher than the p-type films deposited at the same T_s. To test the applicability of these films as gate contact Al/poly-Si/SiO₂/Si capacitor structures with oxide thickness of 4 nm were fabricated on n-type c-Si wafers. Sputter etching of the poly-Si was optimized in order to fabricate the devices. The performance of the HWCVD poly-Si as gate material was monitored using C–V measurements on a MOS test device at different frequencies. The results reveal that as deposited poly-Si without annealing shows low series resistance.     

Low temperature internal friction of diamond-like carbon films

We have studied the internal friction of amorphous diamond-like carbon films prepared by pulsed-laser deposition from 0.4 to 300 K. The low temperature internal friction below 10 K is dominated by the atomic tunneling states for amorphous solids, which is a measure of structure disorder. We have tried to vary the content of sp³ carbon atoms versus sp² ones by changing laser fleunce, by doping with N and Ar, and by annealing at 500 °C for 20 min. Our results show that the internal friction varies about one order of magnitude from 2×10⁻⁵ to 2×10⁻⁴, and its value is higher with higher sp³ content when the film quality is generally considered superior. However, it is known that as-deposited diamond-like carbon films with high sp³ content are heavily stressed. Annealing and doping are used to release the stress. We conclude that in addition to tetrahedral bonding, low stress is also important in reducing structure disorder associated with the low energy tunneling states in amorphous solids.     

Growth and spectroscopy of Dy doped in ZnWO4 crystal

Single-crystal ZnWO₄:Dy³⁺ was grown by Czochralski technique. The XRD, absorption spectra as well as fluorescence spectrum are investigated and the Judd–Ofelt intensity parameters Ω₂, Ω₄, Ω₆ are obtained to be 7.76 × 10⁻²⁰ cm², 0.57 × 10⁻²⁰ cm², 0.31 × 10⁻²⁰ cm², respectively. Calculated radiative transition rate, branching ratios and radiative lifetime for different transition levels of ZnWO₄:Dy³⁺ crystals are presented. Fluorescence lifetime of ⁴F_9/2 level is 158 μs and quantum efficiency is 66%.The most intense fluorescence line at 575 nm correlative with transition ⁴F_9/2 → ⁶H_13/2 is potentially for application of yellow lasers.     

Preparation and characterization of chemically deposited PbSnS3 thin films

High-quality and well-reproducible PbSnS₃ thin films have been prepared by a simple and inexpensive chemical-bath deposition method from an aqueous medium, using thioacetamide as a sulphide ion source. X-ray diffraction analysis of the deposited films revealed that the as-deposited films were amorphous, however, an amorphous-to-crystalline phase transition was observed as the result of thermal annealing at 425 K for 1 h. The X-ray structure analysis of the collected powder from the bath annealed at 425 K for 1.5 h revealed an orthorhombic phase.

Analysis of the optical absorption data of crystalline PbSnS₃ films revealed that both direct and indirect optical transitions exist in the photon energy range 1.24–2.48 eV with optical band gaps of 1.68 and 1.42 eV, respectively. However, a forbidden direct optical transition with a band gap value of 1.038 eV dominates at low energy (<1.24 eV). The refractive index changes from 3.38 to 2.16 in the range 500–1300 nm. The high frequency dielectric constant and the carrier concentration to the effective mass ratio calculated from the refractive index analysis were found to be 4.79 and 2.3×10²⁰ cm⁻³, respectively. The temperature dependence of the electrical resistivity of the deposited films follows the semiconductor behaviour with extrinsic and intrinsic conduction. The determined activation energies range are 0.35–0.42 and 0.76–85 eV, respectively.     

New transparent conducting MgIn2O4---Zn2In2O5 thin films prepared by magnetron sputtering

New materials for a transparent conducting oxide film are demonstrated. Highly transparent Zn₂In₂O₅ films with a resistivity of 3.9 × 10⁻⁴ Ω cm were prepared on substrates at room temperature using a pseudobinary compound powder target composed of ZnO (50 mol.%) and In₂O₃ (50 mol.%) by r.f. magnetron sputtering. MgIn₂O₄---Zn₂In₂O₅ films were prepared using MgIn₂O₄ targets with a ZnO content of 0–100 wt.%. The resistivity of the deposited films gradually decreased from 2 × 10⁻³ to 3.9 × 10⁻⁴ Ω cm as the Zn/(Mg + Zn) atomic ratio introduced into the films was increased. The greatest transparency was obtained in a MgIn₂O₄ film. The optical absorption edge of the films decreased as the Zn/(Mg + Zn) atomic ratio was increased, corresponding to the bandgap energy of their materials. It was found that the resistance of the undoped Zn₂In₂O₅ films was more stable than either the undoped MgIn₂O₄, ZnO or In₂O₃ films in oxidizing environments at high temperatures.     

Semiconducting and structural properties of CrSi2 A-type epitaxial films on Si(111)

Chromium disilicide (CrSi₂) films 1 000 Å thick have been prepared by molecular beam epitaxy on CrSi₂ templates grown on Si(111) substrate. The effect of the substrate temperature on the structural, electrical and optical properties of CrSi₂ films has been studied by transmission and scanning electron microscopies, optical microscopy, electrical resistivity and Hall effect measurements and infrared optical spectrometry. The optimal temperature for the formation of the epitaxial A-type CrSi₂ film have been found to be about 750°C. The electrical measurement have shown that the epitaxial A-type CrSi₂ film is p-type semiconductor having a hole concentration of 1 × 10¹⁷cm⁻³ and Hall mobility of 2 980 cm² V⁻¹ s⁻¹ at room temperature. Optical absorption coefficient data have indicated a minimum, direct energy gap of 0.34 eV. The temperature dependence of the Hall mobility (μ) in the temperature range of T = 180–500 K can be expressed as μ = 7.8 × 10¹⁰T⁻³cm²V⁻¹s⁻¹.     

Highly conducting indium tin oxide (ITO) thin films deposited by pulsed laser ablation

Highly conducting and transparent indium tin oxide (ITO) thin films were prepared on SiO₂ glass and silicon substrates by pulsed laser ablation (PLA) from a 90 wt.% In₂O₃-10 wt.% SnO₂ sintered ceramic target. The growths of ITO films under different oxygen pressures (P_O2) ranging from 1×10⁻⁴–5×10⁻² Torr at low substrate temperatures (T_s) between room temperature (RT) and 200°C were investigated. The opto-electrical properties of the films were found to be strongly dependent on the P_O2 during the film deposition. Under a P_O2 of 1×10⁻² Torr, ITO films with low resistivity of 5.35×10⁻⁴ and 1.75×10⁻⁴ Ω cm were obtained at RT (25°C) and 200°C, respectively. The films exhibited high carrier density and reasonably high Hall mobility at the optimal P_O2 region of 1×10⁻² to 1.5×10⁻² Torr. Optical transmittance in excess of 87% in the visible region of the solar spectrum was displayed by the films deposited at Po₂≥1×10⁻² Torr and it was significantly reduced as the P_O2 decreases.     

Elastic stiffness and thermal expansion coefficients of various refractory silicides and silicon nitride films

The elestic stiffness parameter E_f/(1−ν_f) and the thermal expansion coefficient _f were obtained for four different silicides (TiSi₂, TaSi₂, MoSi₂ and WSi₂) and for two different nitrides (chemically vapor-deposited Nitrox Si₃N₄ and r.f. plasma SiN) from stress-temperature measurements on identical films deposited on two different substrate materials. The values determined for _f and E_f/(1−ν_f) were quite similar for all silicides and averaged 15 ppm °C⁻¹ and 1.1 × 10¹² dyncm⁻² respectively. The thermal mismatch of these silicides is such that, once safely formed, the silicide film should be able to withstand high temperature processing steps without cracking. For the nitrides the values were essentially the same (approximately 1.5 ppm°C^-1), although the larger value of E_f/(1−ν_f) chemically vapor-deposited Si₃N₄ film (3.7 × 10¹² as opposed to 1.1 × 10¹² dyn cm^-2) indicates that it is somewhat stiffer than the SiN film.     

Transparent conductive In2O3:Mo thin films prepared by reactive direct current magnetron sputtering at room temperature

An amorphous transparent conductive oxide thin film of molybdenum-doped indium oxide (IMO) was prepared by reactive direct current magnetron sputtering at room temperature. The films formed on glass microscope slides show good electrical and optical properties: the low resistivity of 5.9 × 10^− 4 Ω cm, the carrier concentration of 5.2 × 10²⁰ cm^− 3, the carrier mobility of 20.2 cm² V^− 1 s^− 1, and an average visible transmittance of about 90.1%. The investigation reveals that oxygen content influences greatly the carrier concentration and then the photoelectrical properties of the films. Atomic force microscope evaluation shows that the IMO film with uniform particle size and smooth surface in terms of root mean square of 0.8 nm was obtained.     

Quantitative analysis of tungsten, oxygen and carbon concentrations in the microcrystalline silicon films deposited by hot-wire CVD

In order for hot-wire chemical vapor deposition to compete with the conventional plasma-enhanced chemical vapor deposition technique for the deposition of microcrystalline silicon, a number of key scientific problems should be cleared up. Among these points, the concentration of tungsten (nature of the filament), as well as the concentration of oxygen and carbon (elements issued when vacuum is broken between two runs), should not exceed threshold values, beyond which electronic properties of the films could be degraded, as in the case of monocrystalline silicon. Quantitative chemical analysis of these elements has been carried out using the secondary ion mass spectrometry technique through depth profiles. It has been shown that for a high effective filament surface area (S_f=27 cm²), the W content increases steadily from 5×10¹⁴ to 2×10¹⁸ atoms cm⁻³ when the filament temperature T_f increases from 1500 to 1800 °C. For a fixed T_f, the W content increases with the effective surface area S_f. Thus, considering our reactor geometry, the W content does not exceed the detection limit (5×10¹⁴ atoms cm⁻³) when T_f and S_f are limited to 1600 °C and 4 cm², respectively. For O and C elements, under deposition conditions of high dilution of silane in hydrogen (96%), O and C concentrations approaching 10²⁰ atoms cm⁻³ have been obtained. The introduction of an inner vessel inside the reactor, the addition of a load-lock chamber and a decrease in substrate temperature to 300 °C have led to a drastic decrease in these contents down to 3×10¹⁸ atoms cm⁻³, compatible with the realization of 6% efficiency HWCVD μc-Si:H solar cells.     

Field-lowering carrier excitation in cadmium arsenide thin films

Cadmium arsenide is a II–V semiconductor which exhibits n-type intrinsic conductivity with high mobility up to μ_n=1.0–1.5 m²/V s. Potential applications include magnetoresistors and both thermal and photodetectors, which require electrical characterization over a wide range of deposition and measurement conditions. The films were prepared by vacuum evaporation with deposition rates in the range 0.5–6.0 nm/s and substrate temperatures maintained at constant values of 20–120°C. Sandwich-type samples were deposited with film thicknesses of 0.1–1.1 μm using evaporated electrodes of Ag and occasionally Au or Al. Above a typical electric field F_b of up to 5×10⁷ V/m all samples showed instabilities characteristic of dielectric breakdown or electroforming. Below this field they showed a high-field conduction process with logJ∝V^1/2, where J is the current density and V the applied voltage. This type of dependence is indicative of carrier excitation over a potential barrier whose effective barrier height has been lowered by the high electric field. The field-lowering coefficient β had a value of (1.2–5.3)×10⁻⁵ eV m^1/2/V^1/2 which is reasonably consistent with the theoretical value of β_PF=2.19×10⁻⁵ eV m^1/2/V^1/2 expected when the field-lowering occurs at donor-like centres in the semiconductor (Poole–Frenkel effect). For thinner films Schottky emission was more probable. The effects of the film thickness, electrode materials, deposition rate, and substrate temperature on the conductivity behaviour are discussed.     

Indium-doped ZnO thin films deposited by the sol–gel technique

Conducting and transparent indium-doped ZnO thin films were deposited on sodocalcic glass substrates by the sol–gel technique. Zinc acetate and indium chloride were used as precursor materials. The electrical resistivity, structure, morphology and optical transmittance of the films were analyzed as a function of the film thickness and the post-deposition annealing treatments in vacuum, oxygen or argon. The obtained films exhibited a (002) preferential growth in all the cases. Surface morphology studies showed that an increase in the films' thickness causes an increase in the grain size. Films with 0.18 μm thickness, prepared under optimal deposition conditions followed by an annealing treatment in vacuum showed electrical resistivity of 1.3 × 10^− 2 Ωcm and optical transmittance higher than 85%. These results make ZnO:In thin films an attractive material for transparent electrodes in thin film solar cells.