CMM Probing Accessibility in a Single Slot

This study presents a novel mathematical method for resolving the accessibility of a through slot when using coordinate measuring machines. The proposed method considers the actual shape of a probe consisting of a motor column, a stylus, and a probe tip. Also derived herein is a mathematical method to derive the feasible probe orientation of the measurement point in the bottom of a slot using a geometrical relationship between the probe and the slot.     

A CO2 tracer-gas method for local air leakage detection and characterization

A method for local measurement of air leakage rate is presented that can be used to accurately and quickly assess leakage rates across a surface, such as around a valve or hatch in a pressurized gas tank or a window in a building. The method uses a small local enclosure with constant volume placed about a region on the structure under investigation (e.g., a window), which is depressurized and injected with a small concentration of carbon dioxide as a tracer gas. The time variation of the pressure and carbon dioxide concentration inside the enclosure are monitored and used to quantify the leakage flow rate as a function of pressure difference. This method uses a small enclosure with internal mixing so that a quasi-steady-state condition is quickly achieved. Because of the small size of the enclosure, advanced data processing techniques are necessary to reduce uncertainty in determination of the rate of change of the carbon dioxide concentration that arises from sensor variability. Results of a laboratory demonstration of the proposed leakage detection and characterization device are reported for the problem of leakage through a circular hole in a plate with prescribed pressure differences. Experimental results from the laboratory tests are found to be in excellent agreement with results of a numerical simulation of leakage flow through a hole, as well as predictions from a number of empirical equations for this problem found in the literature.     

The interaction between two wearing surfaces I: Copper sliding on Cu-Be and Cu-Be sliding on Cu-Be

The work reported in this paper is an investigation of the interaction of the two components of a wear system with reference to the physical properties of both components. Copper sliding on Cu-Be and Cu-Be sliding on Cu-Be were studied using a ball-on-disc machine, Auger spectroscopy and microhardness measurements. The two systems are found to be qualitatively similar classic examples of severe wear. The wear of a Cu-Be disc sliding under a copper ball is, however, greater than the wear of a Cu-Be disc sliding under a Cu-Be ball. This is attributed to work hardening of the copper ball resulting from an interaction between the two wearing surfaces. Microhardness measurements show that the surface of a Cu-Be ball and a Cu-Be disc are not work hardened during a wear experiment. The surface of a copper ball is work hardened, however, and becomes significantly harder than the wear scar on a Cu-Be ball. As a result the Cu-Be disc wears at a faster rate when sliding under a copper ball than it does when sliding under a Cu-Be ball.     

Decrease in the operating gas pressure in an ion source

The results of use of a cold hollow cathode with a multipole magnetic field in a duoplasmatron-type ion source are described. The operating parameters of a duoplasmatron with the developed cathode and a duoplasmatron with a cold hollow two-cylinder cathode are compared. It is shown that the use of a cathode with a multipole magnetic field offers additional possibilities of reducing the operating gas pressure in an ion source and contributes to an increase in both the current and the phase density of the ion-beam current at the output of a charged-particle source and to a decrease in the phase volume of this beam.     

Determination of the velocity and size of bubbles in two-phase flows by using a laser doppler anemometer

Natural oscillations of a spherical interface between a gas and a liquid in a bubble are registered. A possibility of measuring the geometric parameters of stationary and moving particles of the disperse phase by a laser Doppler anemometer is demonstrated. A method for simultaneous determination of the size and velocity of a bubble or a droplet in a two-phase flow is developed. The mean sizes of a group of bubbles settled on a ruler are compared: the results are obtained by two independent methods, i.e., by analyzing the image and by processing the Doppler signal containing information about the natural oscillations of the spherical interface between the media. A possibility of using a laser Doppler anemometer for simultaneous measurements of the velocity and size of bubbles or droplets in a two-phase flow is confirmed.     

Theoretical foundations of ultrasonic nondestructive testing of multilayer articles manufactured from composites with rubbery coatings: II. Scattering of elastic waves at flaws involving poorly glued joints between plastic layers and between a plastic layer and a rubbery coating

The second part of this study is devoted to the solution of the following problems: (i) excitation of plate modes with a lumped force applied to the plate’s surface, (ii) scattering of a bending wave at a small crack parallel to the plate’s surface, and (iii) scattering at a flaw involving a poorly glued joint between a rubbery coating and a plastic layer. The final formulas and numerical dependences for calculating the parameters of a crack or a cleavage are presented. A mathematical model that describes the scattering of waves by flaws in a multilayer article made from a plastic composite material has been developed.     

套式钻模的应用研究

在各种长度和直径的圆柱体或空心圆柱体的外圆柱面上沿横截面圆周方向钻削,有较高的位置精度要求且呈多层均匀分布或多层非均匀分布或螺旋均匀分布或螺旋非均匀分布的孔和螺纹孔的方法进行了研究,重点介绍了长度与外径比＆gt;5的圆柱体或空心圆柱体。研究发现,目前常见的固定式钻模、回转分度式钻模、移动式钻模、翻转式钻模和盖板式钻模都不是最佳选择,因为它们的钻模板均为长方体,与圆柱面不能完全配合,导致夹紧元件和定位元件的结构复杂,形式单一且制造周期长,成本高,夹紧钻模的方式单一。套式钻模的钻模板为空心圆柱体,空心圆柱体的独特之处是使套式钻模可与圆柱面完美配合,夹紧元件和定位元件的结构简单,形式灵活且制造周期短,成本低,夹紧钻模的方式灵活,从而使其成为在各种长度和直径的圆柱体或空心圆柱体的外圆柱面上钻削各种排列组合方式的孔和螺纹孔的最佳选择。     

Microwave atomic force microscopy imaging for nanometer-scale electrical property characterization

We introduce a new type of microscopy which is capable of investigating surface topography and electrical property of conductive and dielectric materials simultaneously on a nanometer scale. The microwave atomic force microscopy is a combination of the principles of the scanning probe microscope and the microwave-measurement technique. As a result, under the noncontact AFM working conditions, we successfully generated a microwave image of a 200-nm Au film coating on a glass wafer substrate with a spatial resolution of 120 nm and a measured voltage difference of 19.2 mV between the two materials.     

智能气体识别仪的研究

智能气体识别仪用以识别气体种类,它具有学习识别多种气体的功能。本文介绍了仪器的工作原理、特点及仪器的硬件和软件构成。     

A broadband Fourier transform microwave spectrometer based on chirped pulse excitation

Designs for a broadband chirped pulse Fourier transform microwave (CP-FTMW) spectrometer are presented. The spectrometer is capable of measuring the 7-18 GHz region of a rotational spectrum in a single data acquisition. One design uses a 4.2 Gsampless arbitrary waveform generator (AWG) to produce a 1 mus duration chirped pulse with a linear frequency sweep of 1.375 GHz. This pulse is sent through a microwave circuit to multiply the bandwidth of the pulse by a factor of 8 and upconvert it to the 7.5-18.5 GHz range. The chirped pulse is amplified by a traveling wave tube amplifier and broadcast inside the spectrometer by using a double ridge standard gain horn antenna. The broadband molecular free induction decay (FID) is received by a second horn antenna, downconverted, and digitized by a 40 Gsampless (12 GHz hardware bandwidth) digital oscilloscope. The second design uses a simplified pulse generation and FID detection scheme, employing current state-of-the-art high-speed digital electronics. In this spectrometer, a chirped pulse with 12 GHz of bandwidth is directly generated by using a 20 Gsampless AWG and upconverted in a single step with an ultrabroadband mixer. The amplified molecular emission is directly detected by using a 50 Gsampless digital oscilloscope with 18 GHz bandwidth. In both designs, fast Fourier transform of the FID produces the frequency domain rotational spectrum in the 7-18 GHz range. The performance of the CP-FTMW spectrometer is compared to a Balle-Flygare-type cavity-FTMW spectrometer. The CP-FTMW spectrometer produces an equal sensitivity spectrum with a factor of 40 reduction in measurement time and a reduction in sample consumption by a factor of 20. The CP-FTMW spectrometer also displays good intensity accuracy for both sample number density and rotational transition moment. Strategies to reduce the CP-FTMW measurement time by another factor of 90 while simultaneously reducing the sample consumption by a factor of 30 are demonstrated.     

Automated fixture configuration using projective geometry approach

The geometric and topological specification of a workpiece boundary is usually represented in a specific data format in a CAD database. To retrieve a set of workpiece data, to analyse its shape in addition to the machining requirements, and to determine the proper fixture configuration accordingly, are not trivial tasks when a part has a complicated shape. The real challenge is to recognise and synthesise the shape of a workpiece from its data representation. Consequently, the decision for fixturing can be made when the shape of a workpiece and the relationship of the shape and the fixturing configuration can be derived by a systematic methodology. In this paper, a projective spatial occupancy enumeration (PSOE) approach is applied as a representational and manipulating scheme for developing algorithms in automatic fixture configuration. The workpiece is projected onto the working plane of the fixture baseplate. A 2D projection is defined as a matrix of cells which can represent a workpiece with an arbitrary shape. Using a discrete search based upon the matrix of cells, the fixture types and their locations are generated according to a set of heuristic algorithms. This work is a generalisation and extension of previous works for prismatic parts. The same methodology is equally applicable in general robot grasping.     

Analysis of acoustic radiation of circular piezoelectric plates enclosed in a flat rigid shield

Acoustic radiation of circular piezoelectric plates encased in a flat rigid shield is analyzed on the basis of a combined numerical-analytical method. It is shown that a plate made of piezoelectric ceramics of the second type with a higher dynamic coefficient of electromechanical coupling ensures a higher sensitivity in the transmission mode and a wider band of radiated frequencies. In addition, a plate of this type of piezoceramics has a lower level of side lobes of the directivity characteristic because of the more uniform normal-displacement distribution on its flat surface.     

A method for measuring and calibrating resistive microtorque of a mechanical microcounter

This paper reports a technique for measuring the calibrating resistive input torque of a micro counter and gearbox assembly. The technique presented uses a hairspring (with a quantifiable output torque) to drive the input shaft to a mechanical counter and gearbox assembly in order to determine its resistive torque. The angular displacement of this spring, a parameter needed to compute the torque, is measured using a combination of a laser diode and a monolithic one-dimensional position sensitive device (PSD). This study includes the steps undertaken to develop it from a concept to functional prototype and interpretation of the results it yields. Tests show that in principle the use of a hairspring and PSD is a viable method of measuring micro-torque.     

The effect of the nature of friction surfaces and lubricant on the adsorption and temperature stability of lubricant layers

The critical temperatures of a mineral oil with an additive under friction, the variations of the electron work function on a metal surface when a thin lubricant layer is applied, and the heat of adsorption of oil on a metal were investigated. A variety of alloy steels, a standard oil (mineral oil with a fatty acid), a standard material (steel) and a mineral oil containing a varying amount of surfactant (succinimide) were used. The data obtained confirm the relationship between the temperature stability of lubricant layers on steel surfaces under friction and the characteristics of oil adsorption on steel.     

Robust scene recognition using a GA and real-world raw-image

This paper presents a new concept of scene recognition by a genetic algorithm (GA), using the 2-D gray-scale image of a working space, termed here as raw-image, and a model shaping the 2-D top-surface of a target object. In fact here, the problem of object recognition in the raw-image is changed into an optimization problem of a model-based evaluation function. We make use in this research of a GA, as a search and optimization method. This GA employs a model-based fitness function as its objective function to perform the search of a target in the raw-image. In this research, three object models, namely a frame model, a surface model, and a surface-strips model are investigated in order to determine which one is the best for scene recognition in a noisy environment. Also, in order to appraise the recognition performance of each model, a comparative study is performed by analyzing the answers to the following criteria questions: sensitivity, reliability, and speed. The effectiveness of the method has been verified through experiments using real-world raw-images, and the method has shown its robustness of object recognition with the surface-strips model, in spite of the noises in the scene.     

Lensless electron reflection microscopy using a coaxial point-source structure

A lensless image of the surface of a crystal is obtained by the reflection on this surface of a low-energy electron beam originated from a point source integrated in a coaxial structure. The point source is a sharp field emission tip and a free propagation of reflected electrons results from the shielding of the tip voltage provided by the coaxial structure. Images are obtained for an incidence angle between 3 and 45 degrees and for nA incident currents with a kinetic energy down to 40 V. On silicon surfaces a magnification up to a few thousands and a spatial resolution of 100 nm are demonstrated.     

计算机辅助设计凸轮及其数控加工

介绍了如何利用计算机对于形状复杂和高精度的凸轮进行辅助设计,以及将设计结果直接在数控机床上加工的方法,分析了图解法设计的局限性和计算机辅助设计的优越性,指出了利用计算机辅助解析法设计是实现数控加工的基础,也是未来机械设计的发展方向。     

A re-configurable cross-sectional imaging system for reverse engineering based on a CNC milling machine

This paper presents a novel reverse engineering digitizing system for full part geometry, which is based on a cross-sectional imaging device built in a NC milling machine. The system successively captures a picture for each planar cross-section contour of the part by end-milling and CCD imaging, and builds the geometry for both external and internal surfaces of the complex 3D part based on a set of the vectored cross-sectional contours. The system mainly consists of three components: a NC milling machine, a cross-sectional imaging device and a computer control unit. Some issues involving the principle and process flow of the system, encasing materials, cross-sectional imaging and NC code generation, etc. are described in detail. Built on an existing NC milling machine, a portable device for capturing the cross-sectional images is designed, which includes an isolated light source, a digital camera, a protective case, a rigid arm and a robust tripod. The device, connected to a computer control unit, serves as a highly flexible accessory for the NC milling machine, constructing the cross-sectional imaging system for reverse engineering. Furthermore, the error analysis and accuracy assessment of the system are also addressed. A typical case is discussed in detail to illustrate the applications of the system. Such a re-configurable digitizing system for reverse engineering offers a number of advantages, such as the functional extension of an existing NC milling machine, low costs, and rapid construction. As a result, this system provides a feasible and useful scheme for many enterprises to construct their own reverse measuring system based on existing equipment to aid in rapid product development and extend the function of existing equipment.     

基于XeF(C-A)放大器的混合(固态/气态)超高功率飞秒激光系统

提出了基于前端发生器和终端放大器,使用光泵浦XeF(C-A)激活介质的太瓦级混合激光器(THIA00)系统.前端发生器由长532 nm的连续激光泵浦的钛宝石飞秒脉冲振荡器,脉冲展宽机构,532 nm的脉冲激光泵浦的再生多通道放大器,衍射光栅压缩器和二次谐波发生器(KDP)组成.其光束输出参数为:脉冲持续时间50 fs,...     

Reconstruction of flaw images by the C-SAFT method from echo signals measured by an antenna array in the triple-scanning mode

The application of antenna matrices (AMs) for obtaining flaw images during automated nondestructive ultrasonic testing is considered. The conventional technique of using an AM as a phased AM (PAM) has a number of drawbacks. One of them is related to the small number of AM elements and consists in a low frontal resolution of the thus-formed images. Scanning with an AM operating in the double scanning mode, viz., the so-called triple-scanning mode, allows coherent summation of partial images for each position and obtaining a resulting image with a frontal resolution that cannot be attained with a PAM. In order to test the serviceability of the proposed algorithm in the CIVA program, echo signals reflected from a crack model with a height of 6 mm and a length of 30 mm in a tested object, which simulated a welded joint of a pipeline with a conventional diameter of 800 mm (дy800), were calculated. The results of the reconstruction of images of model objects in the form of a drilled side hole with a diameter of 6 mm at a depth of 15 mm in a CO-2 specimen and a fatigue crack in a welded joint of a д y800 pipeline are presented. To reduce the influence of reverberation noise, a B-type median template was subtracted from echo signals. The flaw images that were reconstructed in numerical and model experiments demonstrate the efficiency of the proposed algorithm.