Electrodeposition of magnetic CoPd thin films: Influence of plating condition

The manufacture and properties evaluation of Co-based thin film alloys are extensively studied because of their magnetic properties that make them a critical element in many different applications and devices. Therefore the electrodeposition of CoPd alloy thin films was studied from a chloride bath containing glycine as additive. The cobalt content in the CoPd deposits varied from 6.4 to 94.0 at% by controlling the pH and [Co²⁺]/[Pd²⁺] ratio in the bath. Current efficiencies were independent of the solution pH and bath composition. The morphology of the deposits depended on the applied current density: current densities higher than 50 mA cm⁻² resulted in deposits with a typical cauliflower morphology. For current densities lower than 25 mA cm⁻² cracks was observed. The XRD measurements showed that all CoPd alloys were amorphous. The magnetic properties for CoPd alloys revealed that the coercivity (H_c) values ranged from 84 up to 555 Oe and the magnetic saturation (M_s) from 0 to 1.73 T.     

Motional heterogeneity and phase separation of semi-interpenetrating networks and mixtures based on functionalised polyurethane and polymethacrylate prepolymers

Semi-interpenetrating polymer networks (SIPNs) and polymer mixtures (1:1 mass ratio) based on segmented polyester polyurethane (PU) with carboxylic groups and methacrylic copolymer (PM) with tertiary amine groups were studied by the electron spin resonance (ESR) spin label method. The concentration of functional groups varied from 0 to 0.45 mmol g⁻¹ in both prepolymers. The ESR spectra of spin labelled PM component were used to characterise the heterogeneity of segmental motion and transitions due to the additional polymer interactions imposed by complementary functional groups. The results were deduced from the temperature dependent ESR spectra. Two component spectra reflect the effect of PU chains on segmental motion of the PM component below the macroscopic glass transition temperature, T_g. The ratio of the fast and slow component was related to the complex polymer-polymer interaction or extent of miscibility. Restrictions of segmental motion of PM chains increase with functional groups concentration and above certain concentration (0.25 mmol g⁻¹) PM segments in the network assess faster motion suggesting a change in the local packing density and domain structure. An increased miscibility and disorganisation of the ordered domains are confirmed by the loss of spherulitic morphology and crystallinity at higher functional groups concentration. PU/PM mixtures reveal similar motional behaviour as SIPNs of the same composition. However, the differences in the fractional amount of fast and slow motions confirm better interpenetration and interaction of the two polymers in the SIPNs. The results of motional heterogeneity and polymer interactions were complemented with the T_gs.     

Electroformed iron and FeCo alloy

Iron and FeCo alloys were electroformed from additive-free acidic chloride baths. Film stress and magnetic properties were strongly influenced by deposition current density and operating temperature. In general, low film stress and low coercivity (H_C) was achieved with low current density and high operating temperature baths. SEM micrographs indicated that these conditions promote large grain growth. Coercivity of electroformed iron films linearly increased with increasing film stress, indicating that magnetoelastic energy is a dominant anisotropy. The addition of 0.25 M CaCl₂ improves current efficiency while maintaining low film stress. The lowest iron film stress of 5 MPa was achieved from 1.5 M FeCl₂ in the absence of CaCl₂ at 20 mA cm⁻² with a current efficiency of 91%. A “normal” codeposition of FeCo was observed in acidic chloride baths, where the deposition rate of Co²⁺ was faster than Fe²⁺. Film compositions also played an important role in magnetic properties of FeCo films in addition to film stress. Magnetic saturation (M_S) of FeCo films increased linearly with an increase in deposited Fe content. High magnetic saturation with low-stress (M_S of 2.3 T and σ=70 MPa) were achieved from 71Fe29Co films.     

Synthesis, structural and magnetic properties of nanostructured Ca0.9Gd0.1MnO3 obtained by modified glycine nitrate procedure (MGNP)

Ca_0.9Gd_0.1MnO₃ nanopowders with perovskite type crystal structure were synthesized by modified glycine nitrate procedure. Nanopowders were prepared by combining glycine with metal nitrates and/or metal acetates in their appropriate stoichiometric ratios. Modification of the procedure was performed by partial replacement of nitrates by acetates, in order to control the burn-up reaction. Obtained Ca_0.9Gd_0.1MnO₃ powders were calcinated in the temperature interval from 850 °C to 950 °C for 10 min. Properties such as phase evolution, lattice parameters, chemical composition and magnetic properties were monitored by DTA, X-ray diffraction, SEM/EDS and magnetic measurements. Magnetic measurements performed at the sample with the smallest crystallite size showed that a 10% of Gd³⁺ substituted Ca²⁺ ions changes antiferromagnetic properties of CaMnO₃ by the introduction of ferromagnetic interaction due to a double exchange between Mn³⁺ and Mn⁴⁺ ions. Presence of competing interactions and their randomness lead to a formation of a spin glass state below Neel temperature T_N = 110 K. From the high temperature magnetic susceptibility measurements effective magnetic moment of manganese ions is determined which lies between the values for Mn³⁺ and Mn⁴⁺ ions.     

The electrochemical redox processes in PMMA gel electrolytes—behaviour of transition metal complexes

Electrochemical properties of polymer gel electrolytes based on polymethylmethacrylate (PMMA) were studied by cyclic voltammetry and impedance spectroscopy using new solid-state PMMA-Cd-Cd²⁺ reference electrode. The suitable potential window of the PC-PMMA system was estimated from -0.2 to + 1.5 V versus Cd-Cd²⁺. New polymer gels containing ferrocene-ferricinium (Fc-Fc⁺) couple and other transition metal complexes were prepared by the direct polymerisation of methylmethacrylate (MMA) monomer and the solution of metal complex and supporting electrolyte in anhydrous aprotic solvent—propylene carbonate (PC). The half-wave potentials and apparent diffusion coefficients of used complexes and their dependence on the composition of the system (liquid or gel) were estimated. Time dependent electrochemical measurements showed almost three order decrease of the diffusion coefficients of ferrocene (Fc) and ferricinium (Fc⁺) cation from 6 × 10⁻⁵ to 2 × 10⁻⁹ cm² s⁻¹ during the polymerisation from the liquid to the polymer state. The results show that the PC-PMMA gel electrolyte can be described as a system of embedded solvent in the polymer network of PMMA without present monomer.     

Probing anodic reaction kinetics and interfacial mass transport of a direct formic acid fuel cell using a nanostructured palladium-gold alloy microelectrode

The anodic reaction kinetics and interfacial mass transport of a direct polymer electrolyte membrane formic acid fuel cell have been investigated in an all solid-state electrochemical cell using a highly active nanostructured palladium-gold alloy microelectrode as an in situ probe. Well-defined “S-shaped” steady-state cyclic voltammograms exhibiting current-rising region at lower overpotentials and limiting current region at higher overpotentials have been first obtained for the electrochemical oxidation of formic acid at varying temperature. The “S-shaped” steady state polarization curves and chronoamperometric curves enable convenient measurements of the anodic reaction kinetics and interfacial mass transport of formic acid under real polymer electrolyte membrane conditions. It is encouragingly found that formic acid can be directly oxidized to CO₂ with the first electron transfer being the likely rate-determining step and the formation of surface poison can be neglected. The exchange current density for the electrooxidation of formic acid is on the order of magnitude of 10⁻⁷ A cm⁻² in the temperature range of 20-60 °C. The permeability and diffusion coefficient of formic acid through a Nafion^® 117 membrane are of the order of magnitude of 10⁻⁹ mol cm⁻¹ s⁻¹ and 10⁻⁶ cm² s⁻¹, respectively. The combination of a nanostructured microelectrode and an all solid-state electrochemical cell offers a versatile approach to evaluate potential electrocatalysts for fuel cells and electrochemical sensors employing polymer electrolyte membranes.     

Facile synthesis of bimodal porous silica and multimodal porous carbon as an anode catalyst support in proton exchange membrane fuel cell

A simple and easy sol-gel approach has been developed to directly synthesize in situ three-dimensionally interconnected uniform ordered bimodal porous silica (BPS) incorporating both the macroporosity and mesoporosity in the lattice without extra synthesis process performed in previous work. Multimodal porous carbon (MPC) was fabricated through the inverse replication of the BPS. The unique structural characteristics such as well-developed 3-D interconnected ordered macropore framework with open mesopores embedded in the macropore walls, large surface area (1120 m² g⁻¹) and mesopore volume (1.95 cm³ g⁻¹) make MPC very attractive as an anode catalyst support in polymer exchange membrane fuel cell. The MPC-supported Pt-Ru alloy catalyst has demonstrated much higher power density toward hydrogen oxidation than the commercial carbon black Vulcan XC-72-supported ones.     

Fe doping and magnetic properties of zincblende SiC ceramics

Fe-doped SiC bulk ceramics were fabricated by hot-pressing, and their magnetic and electronic properties were investigated. Si_1−xFe_xC (x ≤ 0.04) samples having a zincblende crystal structure exhibited ferromagnetic hysteresis at room temperature with the saturation magnetization increasing with x. X-ray diffraction measurements revealed the creation of a Fe₃Si phase in the samples with its density increasing with x. The samples were found to be p-type semiconductors with a hole concentration (electrical resistivity) of ∼10¹⁹ cm⁻³ (∼10⁰ Ω cm) at room temperature. The observed magnetic properties of the samples are mainly ascribed to the presence of ferromagnetic Fe₃Si crystallites. The high carrier concentration of the samples likely implies the existence of acceptors due to individual Fe³⁺ occupation of the Si sites in the lattice. The randomly distributed Fe³⁺ ions represent a minor contribution to the magnetization of the samples through the formation of magnetic polarons with the carriers.     

Magnetic resonance and conductivity study of gelatin-based proton conductor polymer electrolytes

This work report results from proton nuclear magnetic resonance (NMR), continuous-wave (CW-EPR) and pulsed electron paramagnetic resonance (P-EPR) and complex impedance spectroscopy of gelatin-based polymer gel electrolytes containing acetic acid, cross-linked with formaldehyde and plasticized with glycerol. Ionic conductivity of 2 × 10⁻⁵ S/cm was obtained at room temperature for samples prepared with 33 wt% of acetic acid. Proton (¹H) line shapes and spin-lattice relaxation times were measured as a function of temperature. The NMR results show that the proton mobility is dependent on acetic acid content in the plasticized polymer gel electrolytes. The CW-EPR spectra, which were carried out in samples doped with copper perchlorate, indicate the presence of the paramagnetic Cu²⁺ ions in axially distorted sites. The P-EPR technique, known as electron spin echo envelope modulation (ESEEM), was employed to show the involvement of both, hydrogen and nitrogen atoms, in the copper complexation of the gel electrolyte.     

Varying carbon structures templated from KIT-6 for optimum electrochemical capacitance

Bicontinuous ordered mesoporous carbons (OMCs), fabricated from a KIT-6 template using aluminosilicate as catalyst and furfuryl alcohol as carbon source, were successfully prepared and studied as electrodes in supercapacitors. Their structures were characterized by transmission electron microscopy (TEM), small-angle X-ray diffraction (SAXD) and N₂ cryosorption methods. Using cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS), the capacitive performance of the OMCs was found to be strongly dependent on the mesostructure. Specific capacitance value greater than 130 F g⁻¹ at 20 mV s⁻¹ were obtained from an OMC that featured high surface area with the existence of additional large pores to enhance the specific capacitance at high discharge rate. For the OMC with the best performance, we found that a power density as high as 4.5 kW kg⁻¹ at an energy density of 6.1 Wh kg⁻¹ can be delivered when the discharge current density is 20 A g⁻¹ and can also be continuously charged and discharged with little variation in capacitance after 2500 cycles. These results indicate that this OMC with optimized structure has potential to be used as a power component in electric vehicles.     

Electrochemically multi-anodized TiO2 nanotube arrays for enhancing hydrogen generation by photoelectrocatalytic water splitting

An enhanced hydrogen production by photoelectrocatalytic water splitting was obtained using extremely highly ordered nanotubular TiO₂ arrays in this work. Highly ordered TiO₂ nanotube arrays with a regular top porous morphology were grown by a facile and green three-step electrochemical anodization. The well ordered hexagonal concaves were uniformly distributed on titanium substrate by the first anodization, served as a template for further growth of TiO₂ nanotubes. As a result, the TiO₂ nanotube arrays constructed through the third anodization showed appreciably more regular architecture than that of the sample by conventional single anodization under the same conditions. The enhanced photoelectrochemical activity was demonstrated through the hydrogen generation by photoelectrocatalytic water splitting, with an exact H₂ evolution rate up to 420 μmol h⁻¹ cm⁻² (10 mL h⁻¹ cm⁻²) in 2 M Na₂CO₃ + 0.5 M ethylene glycol. The photocurrent density of the third-step anodic TiO₂ nanotubes is about 24 mA cm⁻² in 0.5 M KOH, which is 2.2 times higher than that of the normal TiO₂ nanotubes (∼11 mA cm⁻²) by a single electrochemical anodization.     

Fabrication of integrated arrays of ultrahigh density magnetic nanowires on glass by anodization and electrodeposition

Integrated nanowire arrays of Fe-Pt, Co-Pt, and Ni-Pt alloys were successfully fabricated on glass substrates by successive anodization and electrodeposition. Porous alumina films, which were formed from an aluminum layers sputter-deposited on glass substrates covered with transparent oxide conductive films, were used as template-electrodes to deposit various magnetic alloys (Fe-Pt, Co-Pt, and Ni-Pt) in the nanopores by a cathodic electrodeposition, thus leading to integrated nanowire arrays with ultrahigh densities of (0.6-2.1) × 10¹⁵ wire m⁻². The as-deposited nanowires of Fe-Pt, Co-Pt, and Ni-Pt alloys are polycrystalline and composed of fine crystals (4-7 nm across) of chemically ordered tetragonal FePt, CoPt, or NiPt phase. The integrated nanowire arrays may be the promising candidate materials for ultrahigh density perpendicular magnetic recording media in terabits per square inch regime, due to the predictable enhanced perpendicular magnetic performance after appropriate annealing.     

The electrochemical redox processes in methacrylate-based polymer electrolytes II. - Study on microelectrodes

The electrochemical behaviour of ferrocene was studied in different gel polymer electrolytes based on methyl, ethyl and 2-ethoxyethyl methacrylate and compared to the liquid aprotic solution (propylene carbonate). Voltammetric and chronoamperometric measurements on microelectrodes were conducted in order to describe the qualitative as well as quantitative behaviour of ferrocene in different conditions. Heterogeneous electron-transfer rate constants and diffusion coefficients of ferrocene in polymer electrolytes were estimated to be 1.1-7.8 × 10⁻³ cm s⁻¹ and 4-13 × 10⁻⁸ cm² s⁻¹ depending on the electrolyte composition. The influence of the polymer polarity, ferrocene concentration and level of polymer cross-linkage on the kinetics of ferrocene oxidation and its transport was discussed. The electrolytes with poly(2-ethoxyethyl methacrylate) exhibit the highest ionic conductivity (2-4 × 10⁻⁴ S cm⁻¹) as well as diffusion coefficient of ferrocene (1.3 × 10⁻⁷ cm² s⁻¹) in their structure.     

Electrochemical quartz crystal nanobalance and chronocoulometry studies of phenylalanine adsorption on Au

The interfacial adsorption behaviour of the amino acid, phenylalanine (Phe), was studied at a polycrystalline Au surface in 0.05 M KClO₄ using cyclic voltammetry, chronocoulometry (CC) and electrochemical quartz crystal nanobalance (EQCN) frequency measurements. The frequency was observed to decrease with increasing concentration of Phe, indicating that the frequency measurements were following analyte adsorption directly. Both CC and EQCN frequency measurements showed a two-stage adsorption process, consistent with the molecule being adsorbed in the horizontal position at negative potentials, but rearranged to the more upright position at potentials more positive to the potential of zero charge. From the slopes at the onset of each of these two regions in plots of change in mass from the EQCN frequency measurements versus the surface charge density from CC measurements, the calculated molar mass corresponded to that of Phe displacing adsorbed water molecules for EQCN measurements made with small bulk concentrations of Phe (i.e., <1 × 10⁻⁴ mol L⁻¹).The adsorption process from CC measurements for Phe, described using the Henry adsorption isotherm, gave Gibbs energies of adsorption (ΔG_ADS) ranging from −18 to −35 kJ mol⁻¹ over the potential range of −0.6 to 0.6 V. The observed decrease in frequency of the EQCN measurements with additions of aliquots of amino acid and the substantial ΔG_ADS values suggests that Phe adsorbs onto the surface via chemisorption. Surface concentrations (1.2 × 10⁻¹⁰ mol cm⁻²) were in excellent agreement between the EQCN and CC measurements for small bulk concentrations of Phe (4.0 × 10⁻⁵ mol L⁻¹), in very good agreement with previously published results at the Au(1 1 1) surface. Thus, for small bulk concentrations of analyte, these electrochemical techniques complement one another to enhance our knowledge of the behaviour of thin organic films at electrode surfaces.     

Electrochemical actuation properties of a novel solution-processable polythiophene

A solution-processable polythiophene, poly((E)-4,4″-didecoxy-3′-styryl[2,2′:5′,2′′]terthiophene) demonstrated large electrochemically induced strain up to 11.5%. Free-standing polymer films were characterised using four-point probe conductivity measurements, cyclic voltammetry and electrochemical actuation measurements. Conductivities of ∼6 × 10⁻⁵ S/cm (reduced state) or ∼1-2 S/cm (oxidised state) were measured. Well-defined polymer oxidation-reduction responses were observed in both the propylene carbonate and acetonitrile electrolytes, with electrochemical efficiency of >80% observed under ideal conditions. Results obtained suggested that the actuation strain approximately correlates with the size of the anion (i.e. TFSI > PF₆⁻ > ClO₄⁻) used in the electrolyte. The largest strain ∼11.5% was obtained in an electrolyte solution consisting of 0.1 M Li.TFSI in acetonitrile. The maximum strain attainable increased with an increase in the anodic potential applied and decreased with an increase in stimulation frequency or increasing mechanical load. Such functionalised polythiophene material has the combined advantage of solution processability and the ability to produce large strain.     

Preparation and characterization of multilayer-type electrolyte membranes with hydrocarbon polymers

Multilayer-type polymer electrolyte membranes composed of a sulfonated poly(4-phenoxybenzoyl-1,4-phenylene) (S-PPBP) layer and a mono[poly(propylene oxide)methacrylate]phosphate ester (PPHP) layer were fabricated by solution-casting procedure (Method 1) and hot-pressing procedure (Method 2) in order to suppress methanol permeability of electrolyte membranes. No delamination was observed by SEM measurements of S-PPBP/PPHP interfaces, indicating that PPHP had good adhesive properties to S-PPBP surfaces. The methanol permeability of S-PPBP/PPHP membranes was lower than that of S-PPBP membranes and decreased with increasing the thickness of PPHP layers. The bilayer membrane with 12 μm PPHP and 40 μm S-PPBP layers showed a methanol permeability of 2.97 × 10⁻⁷ cm² s⁻¹ in 1 mol dm⁻³ methanol aqueous solution at 25 °C, which was 13% less than that of the S-PPBP membranes. The conductivity of this membrane reached its optimum with values as high as 1.57 × 10⁻¹ S cm⁻¹ at 80 °C and 90%RH.     

Growth of magnetic carbon with a nanoporous and graphitic structure

A porous magnetic composite is synthesized in which each magnetic nanoparticle is closely encapsulated by several graphitic layers and the resulting units are embedded in a carbon matrix with a nanoporous and graphitic structure. The experiments involve preparation of an iron-containing carbon precursor by thermal pyrolysis and subsequent heat treatment of the precursor. Both magnetic particles and porous carbon with a graphitic structure are formed at the same time. After the heat treatment, no additional treatment is needed. The prepared sample has a high surface area of 275-395 m² g⁻¹, a high saturation magnetism of 43-65 emu g⁻¹ and a high coercivity of 370-650 Oe.     

Characterization of submicrometer-sized NiZn ferrite prepared by spark plasma sintering

High-density submicrometer-sized Ni_0.5Zn_0.5Fe₂O₄ ferrite ceramics were prepared by spark plasma sintering in conjunction with sufficient high energy ball milling. They were evaluated by different characterization techniques such as X-ray diffraction, scanning electron microscopy, and dielectric and magnetic measurements. All samples prepared at sintering temperatures ranging from 850 to 925 °C exhibit a single spinel phase and their relative densities and grain sizes range from 90% to 99% and ~100 nm to ~300 nm, respectively. The dielectric constant increases with decreasing grain size until ~250 nm, and then decreases dramatically with further decreasing grain size. The saturation magnetization increases continuously with increasing grain size/density but the magnetic coercivity decreases. The highest dielectric constant and saturation magnetization at room temperature are approximately 1.0×10⁵ and 84.4 emu/g, respectively, while the lowest magnetic coercivity is only around 15 Oe. These outstanding properties may be associated with high density and uniform microstructure created by spark plasma sintering. Therefore, the spark plasma sintering is a promising technique for fabricating high-quality NiZn ferrites with high saturation magnetization and low coercivity.     

Unobstructed electron transfer on porous polyelectrolyte nanostructures and its characterization by electrochemical surface plasmon resonance

Thin organic films with desirable redox properties have long been sought in biosensor research. We report here the development of a polymer thin film interface with well-defined hierarchical nanostructure and electrochemical behavior, and its characterization by electrochemical surface plasmon resonance (ESPR) spectroscopy. The nano-architecture build-up is monitored in real time with SPR, while the redox response is characterized by cyclic voltammetry in the same flow cell. The multilayer assembly is built on a self-assembled monolayer (SAM) of 1:1 (molar ratio) 11-ferrocenyl-1-undecanethiolate (FUT) and mercaptoundecanoic acid (MUA), and constructed using a layer-by-layer deposition of cationic poly(allylamine hydrochloride) (PAH) and anionic poly(sodium 4-styrenesulfonate) (PSS). Electron transfer (ET) on the mixed surface and the effect of the layer structures on ET are systematically studied. Under careful control, multiple layers can be deposited onto the 1:1 FUT/MUA SAM that presents unobstructed redox chemistry, indicating a highly ordered, extensively porous structure obtained under this condition. The use of SPR to trace the minute change during the electrochemical process offers neat characterization of local environment at the interface, in particular double layer region, allowing for better control over the redox functionality of the multilayers. The 1:1 SAM has a surface coverage of 4.1 ± 0.3 × 10⁻¹⁰ mol cm⁻² for ferrocene molecules and demonstrates unperturbed electrochemistry activity even in the presence of a 13 nm polymer film adhered to the electrode surface. This thin layer possesses some desirable properties similar to those on a SAM while presenting ∼15 nm exceedingly porous structure for high loading capacity. The high porosity allows perchlorate to freely partition into the film, leading to high current density that is useful for sensitive electrochemical measurements.     

Synthesis and electrochemical properties of lithium methacrylate-based self-doped gel polymer electrolytes

In this study, a strategy for synthesizing lithium methacrylate (LiMA)-based self-doped gel polymer electrolytes was described and the electrochemical properties were investigated by impedance spectroscopy and linear sweep voltammetry. LiMA was found to dissolve in ethylene carbonate (EC)/diethyl carbonate (DEC) (3/7, v/v) solvent after complexing with boron trifluoride (BF₃). This was achieved by lowering the ionic interactions between the methacrylic anion and lithium cation. As a result, gel polymer electrolytes consisting of BF₃-LiMA complexes and poly(ethylene glycol) diacrylate were successfully synthesized by radical polymerization in an EC/DEC liquid electrolyte. The FT-IR and AC impedance measurements revealed that the incorporation of BF₃ into the gel polymer electrolytes increases the solubility of LiMA and the ionic conductivity by enhancing the ion disassociations. Despite the self-doped nature of the LiMA salt, an ionic conductivity value of 3.0 × 10⁻⁵ S cm⁻¹ was achieved at 25 °C in the gel polymer electrolyte with 49 wt% of polymer content. Furthermore, linear sweep voltammetry measurements showed that the electrochemical stability of the gel polymer electrolyte was around 5.0 V at 25 °C.