Exergy analysis,parametric analysis and optimization for a novel combined power and ejector refrigeration cycle

A new combined power and refrigeration cycle is proposed, which combines the Rankine cycle and the ejector refrigeration cycle. This combined cycle produces both power output and refrigeration output simultaneously. It can be driven by the flue gas of gas turbine or engine, solar energy, geothermal energy and industrial waste heats. An exergy analysis is performed to guide the thermodynamic improvement for this cycle. And a parametric analysis is conducted to evaluate the effects of the key thermodynamic parameters on the performance of the combined cycle. In addition, a parameter optimization is achieved by means of genetic algorithm to reach the maximum exergy efficiency. The results show that the biggest exergy loss due to the irreversibility occurs in heat addition processes, and the ejector causes the next largest exergy loss. It is also shown that the turbine inlet pressure, the turbine back pressure, the condenser temperature and the evaporator temperature have significant effects on the turbine power output, refrigeration output and exergy efficiency of the combined cycle. The optimized exergy efficiency is 27.10% under the given condition.     

First and second law analysis of solar operated combined Rankine and ejector refrigeration cycle

A combined Rankine and ejector refrigeration cycle is proposed for the production of power and refrigeration output using duratherm 600 oil as the heat transfer fluid. Thermodynamic analysis has been done to observe the effect of parameters on the performance of the combined cycle. The effect of various parameters asthe turbine inlet pressure, evaporator temperature, condenser temperature, extraction ratio and direct normal radiation per unit area on the performance of the cycle have significant effects on the net power output, refrigeration output, first law efficiency and second law efficiency. It is also observed that the maximum irreversibility occurs in central receiver as 52.5% followed by 25% in the heliostat, 5.3% in the heat recovery vapor generator, 2.6% in the ejector, and 1.6% in the turbine and around 1.1% in the other components of the cycle. The second law efficiency of the solar operated combined Rankine and ejector refrigeration cycle is 11.90% which is much lower than its first law efficiency of 14.81%.     

Parametric analysis and optimization for a combined power and refrigeration cycle

A combined power and refrigeration cycle is proposed, which combines the Rankine cycle and the absorption refrigeration cycle. This combined cycle uses a binary ammonia–water mixture as the working fluid and produces both power output and refrigeration output simultaneously with only one heat source. A parametric analysis is conducted to evaluate the effects of thermodynamic parameters on the performance of the combined cycle. It is shown that heat source temperature, environment temperature, refrigeration temperature, turbine inlet pressure, turbine inlet temperature, and basic solution ammonia concentration have significant effects on the net power output, refrigeration output and exergy efficiency of the combined cycle. A parameter optimization is achieved by means of genetic algorithm to reach the maximum exergy efficiency. The optimized exergy efficiency is 43.06% under the given condition.     

Performance analysis of a waste‐heat‐powered thermodynamic cycle for multieffect refrigeration

A multieffect refrigeration system that is based on a waste‐heat‐driven organic Rankine cycle that could produce refrigeration output of different magnitudes at different levels of temperature is presented. The proposed system is integration of combined ejector–absorption refrigeration cycle and ejector expansion Joule–Thomson (EJT) cooling cycle that can meet the requirements of air‐conditioning, refrigeration, and cryogenic cooling simultaneously at the expense of industrial waste heat. The variation of the parameters that affect the system performance such as industrial waste heat temperature, refrigerant turbine inlet pressure, and the evaporator temperature of ejector refrigeration cycle (ERC) and EJT cycles was examined, respectively. It was found that refrigeration output and thermal efficiency of the multieffect cycle decrease considerably with the increase in industrial waste heat temperature, while its exergy efficiency varies marginally. A thermal efficiency value of 22.5% and exergy efficiency value of 8.6% were obtained at an industrial waste heat temperature of 210°C, a turbine inlet pressure of 1.3 MPa, and ejector evaporator temperature of 268 K. Both refrigeration output and thermal efficiency increase with the increase in turbine inlet pressure and ERC evaporator temperature. Change in EJT cycle evaporator temperature shows a little impact on both thermal and exergy efficiency values of the multieffect cycle. Analysis of the results clearly shows that the proposed cycle has an effective potential for cooling production through exploitation of lost energy from the industry. Copyright © 2014 John Wiley & Sons, Ltd.     

First and second law investigations of a new solar‐assisted thermodynamic cycle for triple effect refrigeration

This investigation is persuaded for the first and second law analyses of a new solar‐driven triple‐effect refrigeration cycle using Duratherm 600 oil (Duratherm Extended Life Fluid, NY, USA) as the heat transfer fluid is performed. The proposed cycle is an integration of ejector, absorption, and cascaded refrigeration cycles that could produce refrigeration output of different magnitude at different temperature simultaneously. Both exergy destruction and losses in each component and hence in the overall system are determined to identify the causes and locations of the thermodynamic imperfection. The effects of some influenced parameters such as hot oil outlet temperature, refrigerant turbine inlet pressure, and the evaporator temperature of ejector and cascaded refrigeration cycle have been observed on the first and second law performances. It is found that maximum irreversibility occurs in central receiver as 52.5% and the second largest irreversibility of 25% occurs in heliostat field. The second law efficiency of the solar driven triple effect refrigeration cycle is 2%, which is much lower than its first law efficiency of 11.5%. Analysis clearly shows that performance evaluation based on the first law analysis is inadequate and hence, more meaningful evaluation must be included in the second law analysis. Copyright © 2013 John Wiley & Sons, Ltd.     

A combined power and ejector refrigeration cycle for low temperature heat sources

A combined power and ejector refrigeration cycle for low temperature heat sources is under investigation in this paper. The proposed cycle combines the organic Rankine cycle and the ejector refrigeration cycle. The ejector is driven by the exhausts from the turbine to produce power and refrigeration simultaneously. A simulation was carried out to analyze the cycle performance using R245fa as the working fluid. A thermal efficiency of 34.1%, an effective efficiency of 18.7% and an exergy efficiency of 56.8% can be obtained at a generating temperature of 395 K, a condensing temperature of 298 K and an evaporating temperature of 280 K. Simulation results show that the proposed cycle has a big potential to produce refrigeration and most exergy losses take place in the ejector.     

喷射式氨-水吸收制冷系统的研究

在传统吸收制冷系统中引入喷射器,根据喷射器理论和吸收制冷循环理论,对新制冷系统的工作性能进行了模拟。分别探讨了冷凝温度、喷射器压缩比等参数对系统性能系数和发生温度的影响。结果表明,在原有吸收制冷系统结构变化不大的情况下,尽管系统性能系数有所下降,但系统发生温度却显著降低,因此,低品位的热源将有可能成为氨吸收制冷的加热热源,对于节能减排具有重要的意义。     

Modeling and optimization of a novel pressurized CHP system with water extraction and refrigeration

A novel cooling, heat, and power (CHP) system has been proposed that features a semi-closed Brayton cycle with pressurized recuperation, integrated with a vapor absorption refrigeration system (VARS). The semi-closed Brayton cycle is called the high-pressure regenerative turbine engine (HPRTE). The VARS interacts with the HPRTE power cycle through heat exchange in the generator and the evaporator. Waste heat from the recirculated combustion gas of the HPRTE is used to power the absorption refrigeration unit, which cools the high-pressure compressor inlet of the HPRTE to below ambient conditions and also produces excess refrigeration in an amount that depends on ambient conditions. Water produced as a product of combustion is intentionally condensed in the evaporator of the VARS, which is designed to provide sufficient cooling for the inlet air to the high-pressure compressor, water extraction, and for an external cooling load. The computer model of the combined HPRTE/VARS cycle predicts that with steam blade cooling and a medium-sized engine, the cycle will have a thermal efficiency of 49% for a turbine inlet temperature of 1400°C. This thermal efficiency, is in addition to the large external cooling load, generated in the combined cycle, which is 13% of the net work output. In addition, it also produces up to 1.4 kg of water for each kg of fuel consumed, depending upon the fuel type. When the combined HPRTE/VARS cycle is optimized for maximum thermal efficiency, the optimum occurs for a broad range of operating conditions. Details of the multivariate optimization procedure and results are presented in this paper. Copyright © 2008 John Wiley & Sons, Ltd.     

Analysis of parameters affecting the performance of gas turbines and combined cycle plants with vapor absorption inlet air cooling

The integration of an aqua‐ammonia inlet air‐cooling scheme to a cooled gas turbine‐based combined cycle has been analyzed. The heat energy of the exhaust gas prior to the exit of the heat recovery steam generator has been chosen to power the inlet air‐cooling system. Dual pressure reheat heat recovery steam generator is chosen as the combined cycle configuration. Air film cooling has been adopted as the cooling technique for gas turbine blades. A parametric study of the effect of compressor–pressure ratio, compressor inlet temperature, turbine inlet temperature, ambient relative humidity, and ambient temperature on performance parameters of plants has been carried out. It has been observed that vapor absorption inlet air cooling improves the efficiency of gas turbine by upto 7.48% and specific work by more than 18%, respectively. However, on the adoption of this scheme for combined cycles, the plant efficiency has been observed to be adversely affected, although the addition of absorption inlet air cooling results in an increase in plant output by more than 7%. The optimum value of compressor inlet temperature for maximum specific work output has been observed to be 25 °C for the chosen set of conditions. Further reduction of compressor inlet temperature below this optimum value has been observed to adversely affect plant efficiency. Copyright © 2013 John Wiley & Sons, Ltd.     

Evaluation of adding flash tank to solar combined ejector–absorption refrigeration system

Performance of the absorption cooling system is still a challenge due to the coefficient of performance (COP) that is generally poor when compared with the conventional vapor compression cycle. High solar radiation in hot climates is usually associated with high ambient temperature and consequently peak cooling demand. Absorption cooling cycles can be powered by solar but the performance is limited by heat source temperature (solar collector) and high ambient temperature that can affect the condensation process. Efficiency enhancement of the system components is essential to increase the COP of the system. A modification in the combined absorption–ejector cooling system is adopted. Adding a removable flash tank between the condenser and evaporator could improve entrainment ratio of the ejector, along with improving the cooling effect inside the evaporator. A computer simulation program is developed to evaluate the performance of the modified combined cycle using aqua-ammonia (NH₃–H₂O) refrigerant. The performance of the proposed combined cooling cycle is compared with basic absorption, and combined absorption–ejector cooling cycles. Results showed a significant improvement in the COP of the modified cycle at different operating conditions. Cooling effect and capacity of the evaporator is enhanced due to the reduction of flash gas delivered to the evaporator. Furthermore, the flash tank optimized the ejector entertainment ratio and consequently increasing the condenser pressure. This optimization will enable the system to perform well in hot climates where the condenser efficiency is limited by ambient temperature.     

无分凝器的氨水吸收式制冷循环系统研究

在常规单级氨水吸收式制冷循环的基础上,本研究提出了一种无分凝器的氨水吸收式制冷循环系统。应用能量和质量守恒方程对循环中不同部件分别建立热力学模型,通过运用C++软件编程,对两种循环的循环特性进行了模拟计算。结果表明:在发生温度为150℃,冷却水进口温度32℃工况下,随蒸发温度的升高无分凝器循环的性能系数越来越接近常规循环,在空调工况下最为接近;反之,越来越偏离常规循环。     

Experimental investigation of a combined ejector-absorption refrigerator

This paper describes an experimental study of a novel heat-operated refrigeration cycle, ‘combined ejector-absorption refrigeration cycle’. In this novel cycle, an ejector was placed between a generator and a condenser of a conventional single-effect absorption refrigerator. The high-pressure vapour refrigerant produced in the generator section was used as the motive fluid for the ejector which entrained low-pressure refrigerant vapour from the evaporator and discharged it to the condenser. This was shown to significantly increase the cooling capacity and COP of the novel refrigerator above that of a conventional absorption unit with little increase in system complexity. © 1998 John Wiley & Sons, Ltd.     

Study of a gas–liquid ejector and its application to a solar-powered bi-ejector refrigeration system

A new configuration of a bi-ejector refrigeration system is presented. The system incorporates two ejectors. The purpose of one is to suck refrigerant vapour from the evaporator and discharge to the condenser; the other acts as a jet pump to pump liquid refrigerant from the condenser to the generator. An analysis model for the bi-ejector refrigeration system and a one-dimensional flow model for the gas–liquid ejector were established. The performances of the gas–liquid ejector and the refrigeration cycle were studied using numerical modelling. The results show that the performances of ejectors and system depend a great deal on the refrigerants as well as on operation conditions.     

Theoretical and experimental investigation of an ammonia–water power and refrigeration thermodynamic cycle

A combined thermal power and cooling cycle proposed by Goswami is under intensive investigation, both theoretically and experimentally. The proposed cycle combines the Rankine and absorption refrigeration cycles, using a binary ammonia–water mixture as the working fluid. This cycle can be used as a bottoming cycle using waste heat from a conventional power cycle or an independent cycle using low temperature sources such as geothermal and solar energy. Initial parametric studies of the cycle showed the potential for the cycle to be optimized for first or second law efficiency, as well as work or cooling output. For a solar heat source, optimization of the second law efficiency is most appropriate, since the spent heat source fluid is recycled through the solar collectors. The optimization results verified that the cycle could be optimized using the generalized reduced gradient method. Theoretical results were extended to include realistic irreversibilities in the cycle, in preparation for the experimental study. An experimental system was constructed to demonstrate the feasibility of the cycle and to compare the experimental results with the theoretical simulation. Results showed that the vapor generation and absorption condensation processes work experimentally. The potential for combined turbine work and refrigeration output was evidenced in operating the system. Analysis of losses showed where improvements could be made, in preparation for further testing over a broader range of operating parameters.     

Analysis of gas turbine operating parameters with inlet fogging and wet compression processes

Inlet fogging has been widely noticed in recent years as a method of gas turbine air inlet cooling for increasing the power output in gas turbines and combined cycle power plants. The effects of evaporative cooling on gas turbine performance were studied in this paper. Evaporative cooling process occurs in both compressor inlet duct (inlet fogging) and inside the compressor (wet compression). By predicting the reduction in compressor discharge air temperature, the modeling results were compared with the corresponding results reported in literature and an acceptable difference percent point was found in this comparison. Then, the effects of both evaporative cooling in inlet duct, and wet compression in compressor, on the power output, turbine exhaust temperature, and cycle efficiency of 16 models of gas turbines categorized in four A–D classes of power output, were investigated. The results of this analysis for saturated inlet fogging as well as 1% and 2% overspray are reported and the prediction equations for the amount of actual increased net power output of various gas turbine nominal power output are proposed. Furthermore the change in values of physical parameters and moving the compressor operating point towards the surge line in compressor map was investigated in inlet fogging and wet compression processes.     

Estimation of ejector's main cross sections in steam-ejector refrigeration system

This paper describes the calculation of main cross sections of a steam-ejector, operating in a refrigeration system. For the detailed calculation of ejector a method has been developed which employs functions describing the thermodynamic properties of steam. The influence of three major parameters: generator pressure, condenser and evaporator temperature on cross sections of ejector is discussed. The design conditions were: generator pressure (6–8 bar), condenser temperature (40–50 °C) and evaporator temperature (4–10 °C). It is confirmed that the dimensions of ejector depend on the operation conditions.     

Thermoeconomic analysis of SOFC-GT-VARS-ORC combined power and cooling system

The integration of the gas turbine cycle and organic Rankine cycle with the solid oxide fuel cell for power generation is quite prevalent. However, the need is also felt for systems capable of providing power with cooling. Therefore, it is proposed to integrate solid oxide fuel cell with gas turbine cycle, vapour absorption refrigeration system and organic Rankine cycle through the heat available with fluid in the cycle. Here intercooled and reheat gas turbine cycle is integrated with solid oxide fuel cell. Heat rejected in intercooling is used in vapour absorption refrigeration system for cooling. This paper presents thermoeconomic analysis. Results show that the combination of solid oxide fuel cell-gas turbine-vapour absorption refrigeration system-organic Rankine cycle yields increase in efficiency to 68.79% as compared to 58.88% from combined solid oxide fuel cell-gas turbine cycle. The cost of electricity per unit power output is found as 1939.93 $/kW.     

Development and thermodynamic assessment of a novel solar and biomass energy based integrated plant for liquid hydrogen production

In this paper, a combined power plant based on the dish collector and biomass gasifier has been designed to produce liquefied hydrogen and beneficial outputs. The proposed solar and biomass energy based combined power system consists of seven different subplants, such as solar power process, biomass gasification plant, gas turbine cycle, hydrogen generation and liquefaction system, Kalina cycle, organic Rankine cycle, and single-effect absorption plant with ejector. The main useful outputs from the combined plant include power, liquid hydrogen, heating-cooling, and hot water. To evaluate the efficiency of integrated solar energy plant, energetic and exergetic effectiveness of both the whole plant and the sub-plants are performed. For this solar and biomass gasification based combined plant, the generation rates for useful outputs covering the total electricity, cooling, heating and hydrogen, and hot water are obtained as nearly 3.9 MW, 6584 kW, 4206 kW, and 0.087 kg/s in the base design situations. The energy and exergy performances of the whole system are calculated as 51.93% and 47.14%. Also, the functional exergy of the whole system is calculated as 9.18% for the base working parameters. In addition to calculating thermodynamic efficiencies, a parametric plant is conducted to examine the impacts of reference temperature, solar radiation intensity, gasifier temperature, combustion temperature, compression ratio of Brayton cycle, inlet temperature of separator 2, organic Rankine cycle turbine and pump input temperature, and gas turbine input temperature on the combined plant performance.     

Thermodynamic analysis of an LNG fuelled combined cycle power plant with waste heat recovery and utilization system

This paper has proposed an improved liquefied natural gas (LNG) fuelled combined cycle power plant with a waste heat recovery and utilization system. The proposed combined cycle, which provides power outputs and thermal energy, consists of the gas/steam combined cycle, the subsystem utilizing the latent heat of spent steam from the steam turbine to vaporize LNG, the subsystem that recovers both the sensible heat and the latent heat of water vapour in the exhaust gas from the heat recovery steam generator (HRSG) by installing a condensing heat exchanger, and the HRSG waste heat utilization subsystem. The conventional combined cycle and the proposed combined cycle are modelled, considering mass, energy and exergy balances for every component and both energy and exergy analyses are conducted. Parametric analyses are performed for the proposed combined cycle to evaluate the effects of several factors, such as the gas turbine inlet temperature (TIT), the condenser pressure, the pinch point temperature difference of the condensing heat exchanger and the fuel gas heating temperature on the performance of the proposed combined cycle through simulation calculations. The results show that the net electrical efficiency and the exergy efficiency of the proposed combined cycle can be increased by 1.6 and 2.84% than those of the conventional combined cycle, respectively. The heat recovery per kg of flue gas is equal to 86.27 kJ s^?1. One MW of electric power for operating sea water pumps can be saved. The net electrical efficiency and the heat recovery ratio increase as the condenser pressure decreases. The higher heat recovery from the HRSG exit flue gas is achieved at higher gas TIT and at lower pinch point temperature of the condensing heat exchanger. Copyright © 2006 John Wiley & Sons, Ltd.     

新型太阳能双喷射制冷系统的理论研究

提出了一个用气—液喷射器代替机械泵的新型双喷射制冷系统。双喷射制冷系统中没有机械泵,从而循环本身不需要消耗电能。研究了气—液喷射器的运行特性和喷射系数与工作参数的关系。分析了双喷射制冷系统COP与发生器温度、冷凝器温度的关系。比较了以R123和R134a为制冷剂的太阳能双喷射制冷系统运行性能。模拟了太阳能双喷射制冷系统的运行性能,COP可达0.2-0.3。