Reinforced mechanical properties of plasma-sprayed Fe-based amorphous composite coatings by in-situ TiNx/TiOy

Ceramic particle-reinforced Fe-based amorphous coatings have received extensive attention due to their excellent strength and wear resistance. In this paper, TiN_x/TiO_y -enhanced Fe-based amorphous coatings were prepared by reactive plasma spraying technology, and the effect of eggshell-like TiN_x/TiO_y on the comprehensive mechanical properties of Fe-based amorphous coatings was systematically studied. The results showed that the hardness of the composite coating was significantly higher than that of the amorphous single-phase coating. Moreover, indentation experiments showed that TiN_x/TiO_y effectively confined crack growth in the amorphous phase. Though the bonding strength of the composite coating was lower than that of the pure amorphous coating, but still maintained a high bonding force of 20.68 MPa. Through the wear experiment, it was found that the wear scar of the composite coatings appeared plastic deformation, the friction coefficient and wear mass loss were both greatly reduced, and the optimal wear performance appeared in the composite coating with 15% Ti addition. In addition, SEM, EDS analysis, and the first-principles simulation results demonstrated the good bonding between Ti-containing compounds and Fe-based alloys.     

Microstructure and tribological properties of multilayered ZrCrW(C)N coatings fabricated by cathodic vacuum-arc deposition

In this study, a series of ZrCrW(C)N multilayer coatings with various transition layers were deposited on AISI304 stainless steel using cathodic vacuum-arc deposition in N₂–C₂H₂ gas mixture. The tribological behaviors of sliding against Al₂O₃ balls under dry friction and lubricant conditions were investigated using a reciprocating tribometer. The results demonstrated that the ZrCrW(C)N coatings comprised (Zr, Cr, W) (C, N) crystallites and an amorphous carbon phase. It possessed a nano-hardness of 35.4 GPa and an elastic modulus of 417.7 GPa. The friction coefficient of the coating was reduced by 14% compared to that of the 304 matrices, and the wear mechanism changed from adhesive wear to slight abrasive wear under the lubrication steady state. Under dry friction conditions, the ZrCrW(C)N coatings with the entire CrWN transition layer exhibited wear rates of 1.27 ± 0.04 × 10^?8 mm³ (N m)^?1, which were one order of magnitude lower than that of the 304 steel. Compared with the untreated AISI304 stainless steel, the ZrCrW(C)N coating exhibits excellent mechanical and tribological properties under lubricated and dry friction conditions, which are crucial for engineering applications.     

Microstructure,mechanical and tribological properties of Mo–V–Cu–N coatings prepared by HIPIMS technique

A combination of high wear-resistance and low-friction is crucial for improving the wear performance of self-lubricating coatings, which is generally determined by an excellent lubricating effect and mechanical strength. In this study, the Mo–V–Cu–N coatings were prepared by HIPIMS technique with a spliced target of Mo–V–Cu at various charge voltages. The results revealed that Mo–V–Cu–N coatings presented a solid solution phase of B1–MoVN with (200) preferred orientation, and the preferred orientation was enhanced at high charge voltages. Whereas the Cu atoms formed an amorphous phase in Mo–V–Cu–N coatings due to a low Cu content of 2.3–3.6 at.%. As the charge voltage increased to 750 V, more charged metallic ions were accelerated and bombarded substrate surface efficiently, forming smooth and dense Mo–V–Cu–N coatings with a high hardness of 31.0 GPa. All the coatings presented a low friction coefficient of 0.34–0.39 due to the formation of MoO₂, VO₂ and CuO mixed oxides, and the wear mechanism was dominated by abrasive and tribo-oxidation wear at room temperature.     

Tribological study of amorphous BC4N coatings

Amorphous BC₄N thin films with a thickness of ∼ 2 μm have been deposited by Ion Beam Assisted Deposition (IBAD) on hard steels substrates, in order to study the wear behavior under high loads and the applicability as protective coatings. The bonding structure of the a-BC₄N film was assessed by X-ray Absorption Near Edge Spectroscopy (XANES) and Infrared Spectroscopy, indicating atomic mixing of B–C–N atoms, with a proportion of ∼ 70% sp² hybrids and ∼ 30% sp³ hybrids. Nanoindentation shows a hardness of ∼ 18 GPa and an elastic modulus of ∼ 170 GPa. A detailed tribological study is performed by pin-on-disk tests, combined with spectromicroscopy of the wear track at the coating and wear scar at pin. The tests were performed at ambient conditions, against WC/Co counterface balls under loads up to 30 N, with the sample rotating at 375 rpm. The coatings suffer a continuous wear, at a constant rate of 2 × 10^− 7 mm³/Nm, without catastrophic failure due to film spallation, and show a coefficient of friction of ∼ 0.2.     

Electrodeposition of graphene oxide-hydroxyapatite composite coating on titanium substrate

In this work, graphene oxide (GO)/hydroxyapatite (HA) composite coatings were successfully prepared on titanium substrate by electrophoretic deposition technology. Subsequently, microstructure, phase composition, adhesion strength, hydrophilicity, corrosion resistance, bioactivity, antibacterial activity and biocompatibility of the coating were evaluated. The adhesion strength of coating increased by 76% from 6.46 MPa to 17.81 MPa with 0 wt% GO to 12 wt% GO and the corrosion rate of coating with 8 wt% GO was achieved at the minima of (1.493 × 10^-3mm/a). Biomineralization experiment indicated the excellent bioactivity of GO/HA composite coatings. The water contact angle of the composite coatings increased from 20.6°(0 wt% GO) to 38.1°(12 wt%GO). The antibacterial rates of coating with 5 wt% GO was 96.7%, while declined to 25% after thermal treatment. In-vitro L929 cell culture experiments indicated the composite coatings with 5 wt% GO exhibited good biocompatibility.     

Strongly adherent Al2O3 coating on SS 316L: Optimization of plasma spray parameters and investigation of unique wear resistance behaviour under air and nitrogen environment

Plasma spray deposition of Al₂O₃ is a well-established technique for thick ceramic coatings on various substrates to shield them from corrosion and wear. Owing to its high hardness, aluminum oxide is known to protect stainless steel substrates from wear. However, the plasma process requires optimization for desired coating thickness and adhesion strength. It is also necessary to understand the sensitivity of friction and wear resistance of the deposited coating on exposed environment for evaluation of service life. The study offers comprehensive investigation on plasma process parameters for the development of strongly adherent aluminium oxide coatings on SS 316L substrate. Impact of environment like dry air and dry nitrogen on tribological properties of the coatings was also investigated. Dense adherent coatings of alumina could be deposited on SS 316L at a plasma power of 20 kW with an intermediate bond coat of NiCrAlY to enhance the adhesion properties. The effects of stand-off distance and bond coat thickness on adhesion strength were additionally examined. Further, the coatings were characterised for phase composition, microstructure, microhardness and wear resistance potential. Reciprocating wear tests of the coatings were carried out using ball on disc reciprocating tribometer at different loading conditions (5, 10 and 15 N) at constant (5 Hz) sliding frequency. Unlike the coefficient of friction (COF), wear volume was found to increase with an increase in normal load. These adherent coatings revealed promising properties for the applications where the tribological failure of SS 316L in dry air or dry nitrogen environment is to be controlled.     

Effects of micro-grooves on tribological behaviour of plasma-sprayed alumina-13%titania coatings

This study was aimed at investigating the effects of micro-grooves on the tribological behaviour of a plasma-sprayed Al₂O₃ – 13%TiO₂ coating. A combined surface profile with non-regular depths and micro-groove texture was successfully developed by using a Nd:YVO₄ laser system. The surface condition and characterisation of the Al₂O₃ – 13%TiO₂ coating was conducted using a VPSEM and a 3D microscope. A pin-on-disc test was then carried out to measure the effectiveness of the micro-grooves in reducing the wear rates of the Al₂O₃ – 13%TiO₂ coatings under non-lubricated conditions. It was noted that the textured coatings gradually decreased the wear rate with only a slight reduction on the friction coefficient due to the entrapment of the wear debris within the grooves. It was proven that the combined surfaces successfully reduced the wear rate up to 44.7% and 61.5% for 10 N and 20 N of load respectively.     

Mechanical and tribological properties of nano/micro composite alumina coatings fabricated by atmospheric plasma spraying

Adding nano particles can significantly improve the mechanical properties and wear resistance of thermal sprayed Al₂O₃ coating. However, it still remains a challenge to uniformly incorporate nano particles into traditional coatings due to their bad dispersibility. In the present work, nanometer Al₂O₃ (n-Al₂O₃) powders modified by KH-560 silane coupling agent were introduced into micrometer Al₂O₃ (m-Al₂O₃) powders by ultrasonic dispersion to afford nano/micro composite feedstock, and then four resultant coatings (weight fraction of n-Al₂O₃: 0%, 3%, 5% and 10%) were fabricated by atmospheric plasma spraying. The features and constitutes of feedstock and as-sprayed coatings, as well as their porosity, bonding strength, microhardness and frictional behaviors were investigated in detail. Results show that the nano/micro composite feedstock with uniform microstructure can be better melted in the spraying process, thereby obtaining coatings with denser microstructure, higher hardness and bonding strength. Added n-Al₂O₃ has no obvious effect on the friction coefficient of composite coatings, whereas can improve their wear-resistant and reduce the worn degree of counterpart. The wear mechanism of traditional coating is brittle fracture and lamellar peeling, while that of composite coating with weight fraction of n-Al₂O₃ of 10% is adhesive wear.     

Graphene oxide/hydroxyapatite composite coatings fabricated by electrophoretic nanotechnology for biological applications

Graphene oxide (GO) was firstly employed as nanoscale reinforcement fillers in hydroxyapatite (HA) coatings by a cathodic electrophoretic deposition process, and GO/HA coatings were fabricated on pure Ti substrate. The transmission electron microscopy observation and particle size analysis of the suspensions indicated that HA nanoparticles were uniformly decorated on GO sheets, forming a large GO/HA particle group. The addition of GO into HA coatings could reduce the surface cracks and increase the coating adhesion strength from 1.55 ± 0.39 MPa (pure HA) to 2.75 ± 0.38 MPa (2 wt.% GO/HA) and 3.3 ± 0.25 MPa (5 wt.% GO/HA), respectively. Potentiodynamic polarization and electrochemical impedance spectroscopy studies indicated that the GO/HA composite coatings exhibited higher corrosion resistance in comparison with pure HA coatings in simulated body fluid. In addition, superior (around 95% cell viability for 2 wt.% GO/HA) or comparable (80–90% cell viability for 5 wt.% GO/HA) in vitro biocompatibility were observed in comparison with HA coated and uncoated Ti substrate.     

Friction and wear property of a-CNx coatings sliding against ceramic and steel balls in water

The amorphous carbon nitride coatings (a-CN_x) were deposited on Si₃N₄ disks using ion beam assisted deposition (IBAD), and their composition and chemical bonding were determined by X-ray photoelectron spectroscopy (XPS). The a-CN_x coatings' hardness was measured by nano-indentation and the friction and wear property of the a-CN_x coatings sliding against Si₃N₄, SiC, Al₂O_3, SUS440C and SUJ2 balls in water were investigated by using ball-on-disk tribo-meter. The worn surfaces were observed using optical microscopy and analyzed by XPS. The results of XPS analysis showed that the a-CN_x coatings contained 12 at.% nitrogen and the major chemical bonding was sp² C = N and sp³C–N. The nano-hardness of the a-CN_x coatings was 29 GPa, higher than those of balls. Among five kinds of tribo-systems, the lowest friction coefficient was obtained in the range of 0.01 to 0.02 for the tribo-systems with SiC and Si₃N₄ balls, the largest wear rate of the a-CN_x coating of 1.77 × 10^− 7 mm³/Nm was obtained as sliding against Al₂O₃ ball, while the smallest wear rate of a-CN_x coating of 1.44 × 10^− 8 mm³/Nm was gotten as sliding against Si₃N₄ ball. However, SUJ2 ball showed the highest wear rate of 7.0 × 10^− 7 mm³/Nm, whereas Al₂O₃ ball exhibited the lowest wear rate of ball of 3.55 × 10^− 9 mm³/Nm. The XPS analysis on the worn surface for the a-CN_x coatings displayed that the nitrogen concentration decreased and the sp²-bonding-rich structure was formed after sliding tests in water.     

Influence of layer number and sintering temperature on microstructural,tribological, and corrosion behavior of Al2O3–TiO2 multilayer coatings

The effects of layer number (2, 4, and 6-layer) and sintering temperature (800, 900, 1000, and 1100 °C) on the microstructure, wear, and corrosion properties of Al₂O₃–TiO₂ multilayer coatings deposited on 316L stainless steel plates using the sol-gel dip coating technique were investigated. The wear characteristics were measured through ball-on-disc type dry sliding tests using an Al₂O₃ ball under a 1 N load, whereas the corrosion features were determined by potentiodynamic polarization tests conducted in a 3.5 wt% NaCl solution. Anatase, rutile, α-Al₂O₃, and γ-Al₂O₃ phases were obtained in the hybrid coatings, depending on the sintering temperatures. However, at 1100 °C, the coating did not adhere well to the substrate due to passive oxide film formation on the 316L plate, leading to spalling. Besides, the surface homogeneity deteriorated in the 6-layer coated sample due to higher organic removal and residual stresses. The corrosion rate decreased with the increasing number of layers, but the sensitivity to corrosion varied due to changes in surface properties. The 4-layer coated sample sintered at 1000 °C achieved the highest wear strength (improved by up to 71.1%) and corrosion resistance (increased by up to 90.4%) due to its decreased porosity and homogeneously distributed finer particles.     

An evaluation of plasma-sprayed coatings based on Al2O3 and Al2O3–13 wt.% TiO2 with bond coat on pure titanium substrate

In this study, the effects of bond coat on the properties of Al₂O₃ and Al₂O₃–13 wt.% TiO₂ coatings, which is plasma sprayed onto a commercial pure titanium substrate with and without Ni–5 wt.% Al (METCO 450 NS) as bond coating layer were investigated in terms of microhardness, bonding strength and surface roughness. Optical and scanning electron microscopy (SEM) examinations revealed that there is a uniform coating layer with no spalling and delamination. However, there is a little amount of porosity. The results indicated that the application of bond coat layer in the plasma spraying of Al₂O₃ and Al₂O₃–13 wt.% TiO₂ on pure titanium substrate has increased the hardness and bonding strength of coatings. While the adhesive bonding is dominant without bond coat, the cohesive bonding is dominant with the application of the bond coating layer. It has been observed that percentage of cohesion strength was about three times higher than that of adhesion strength.     

Effects of modification of hBN by nickel plating on coating structure and properties of supersonic plasma spraying NiCr-Cr3C2-hBN@Ni coatings

Hexagonal boron nitride (hBN) with excellent self-lubrication performance is expected to relieve the friction resistance and wear of NiCr–Cr₃C₂ coatings. However, the poor wettability of hBN with most materials makes it difficult to fabricate NiCr–Cr₃C₂-hBN composite coating with good cohesion strength. In this study, hBN was firstly pretreated through magnetron-sputtering aided Ni plating to form hBN@Ni particles. Then, NiCr–Cr₃C₂-hBN@Ni powder was prepared by spray granulation. Next, corresponding coatings were prepared through supersonic atmosphere plasma spraying. It was found that in comparison with NiCr–Cr₃C₂-hBN coating, the NiCr–Cr₃C₂-hBN@Ni coating exhibited a decreased porosity (from 3.6% to 0.3%), elevated cohesion (from 52.78 N to 62.11 N), and the wear rate decreased by an order of magnitude. It was concluded that hBN@Ni can effectively improve the component interface inside powder, enhance the cohesion of molten in-flight particles, and make the internal structure of the coating denser.     

Optimized a-C coatings by doping with zirconium for tribological properties and machining performance

In this study, a-C:Zr_x% coatings with various levels of zirconium (Zr) addition are deposited on cemented tungsten carbide (WC-Co) substrates using a medium frequency twin magnetron sputtering and unbalanced magnetron sputtering system. The tribological properties of the coatings are investigated by conducting wear tests against an AISI 1045 steel counterbody under a cylinder-on-disk line contact wear mode using an oscillating friction and wear tester system. The machining performance of coated turning cutters and micro-drills is then evaluated by performing turning tests and high-speed through-hole drilling tests using AISI 1045 steel counterbodies and printed circuit board workpieces, respectively. The experimental results reveal that the fabricated a-C:Zr_x% coatings not only have improved tribological properties, but also yield an enhanced machining performance. For sliding against the AISI 1045 steel counterbody under loads of 10 N and 100 N, respectively, the optimal tribological properties are provided by the a-C:Zr_13%coating. However, the optimal turning and drilling performance is obtained using the a-C: Zr_45% coating.     

Enhancement of mechanical properties of hydroxyapatite coating prepared by electrophoretic deposition method

The addition of bio-inert ceramics such as alumina and zirconia can significantly improve the mechanical properties of hydroxyapatite bioactive coatings and increase their biocompatibility. In the present study, the surface of a titanium substrate was coated by the electrophoretic deposition method (EPD). Moreover, the reaction bonding process has been used to precipitate the nanocomposite containing the hydroxyapatite (HA), alumina, yitteria-stabilized zirconia (YSZ). The coating process was performed by an electrical power supply and a suspension of hydroxyapatite, aluminum, and YSZ nanopowders. For preparing a suspension consisting of 50% isopropanol and 50% acetone, 0.6 g/L of iodine was used as a stabilizer. Green and sintered coatings were analyzed by FE-SEM and XRD. In addition, the mechanical properties such as bonding strength, hardness, and toughness were measured. The hardness, bonding strength, and toughness of the HA coating were 107 ± 10.3 HV, 10.8 ± 3.2MPa, and 0.72MPa√m, respectively, while those of the HA-Al₂O₃-YSZ nanocomposite coating were 213 ± 1.8 HV, 35 ± 1.6MPa, and 1.6MPa√m, respectively.     

SiC nanoparticles incorporation in electroless NiP-Graphene oxide nanocomposite coatings

The presence of SiC nanoparticles within the Graphene oxide (GO) incorporated electroless deposited NiP layers (NiP-GO) on carbon steel substrate was studied in this work. The effect of co-deposition of GO nanoplatelets and/or SiC nanoparticles on the morphology and structure of the heat-treated NiP coatings were investigated by scanning electron microscope and X-ray diffraction, respectively. The results revealed that the heat-treated NiP and NiP–SiC coatings consisted of Ni and Ni₃P phases, whereas the NiP-GO also contains the intermediated Ni₂P and Ni₁₂P₅ metastable phases due to the incomplete precipitation of Ni₃P. Such metastable phases are significantly decreased by the incorporation of SiC nanoparticles in NiP-GO coatings. The mechanical properties of the coatings were characterized by microhardness measurement and “pin on disk” wear test. The corrosion tests were conducted in aqueous 3.5 %wt NaCl using electrochemical measurement for Ni–P, NiP-GO, NiP–SiC, and NiP-GO-xSiC coatings. By co-deposition of SiC nanoparticles, the hardness of NiP-GO is significantly increased and the wear loss is reduced, especially at a high sliding distance during the wear test. The corrosion behavior of the NiP-GO coatings containing different amounts of SiC nanoparticles has been investigated.     

Chemical synthesis of TiO2 nanoparticles and their inclusion in Ni–P electroless coatings

The work addresses the preparation of Ni3P3TiO₂ nanocomposite coatings on mild steel substrate by the electroless technique. Nanosized TiO₂ particles were first synthesized by the precipitation method and then were codeposited (4 g/l) into the Ni3P matrix using alkaline hypophosphite reduced EL bath. The surface morphology, particle size, elemental composition and phase analysis of as-synthesized TiO₂ nanoparticles and the coatings were characterized by field emission scanning electron microscopy (FESEM), energy-dispersive analysis of X-ray (EDAX) and X-ray diffraction (XRD). Coatings with 20 µm thickness were heat treated at 400 °C for 1 h in argon atmosphere. The morphology, microhardness, wear resistance and friction coefficient characteristics (ball on disc) of electroless Ni3P3TiO₂ nanocomposite coatings were determined and compared with Ni3P coatings. The results show that as-synthesized TiO₂ nanoparticles are spherical in shape with a size of about12 nm. After heat treatment, the microhardness and wear resistance of the coatings are improved significantly. Superior microhardness and wear resistance are observed for Ni3P3TiO₂ nanocomposite coatings over Ni3P coatings.     

Improving the properties of remanufactured wear parts of shield tunneling machines by novel Fe-based composite coatings

With the aim of remanufacturing high-value wear parts of shield tunneling machines, novel Fe-based composite coatings were prepared by collaborative modification with nano-TiC and nano-CeO₂ particles. This work aims to improve the wear properties of Fe-based alloy coatings by regulating the morphology and dispersion of TiC through the addition of different contents of nano-TiC and nano-CeO₂. First, the coatings with different contents of nano-TiC (from 5 wt% to 15 wt%) and nano-CeO₂ (from 1 wt% to 2 wt%) were prepared by laser cladding. Subsequently, the microstructure, phase composition, microhardness, and wear properties of the coatings were examined. Furthermore, the wear morphology and the influence mechanism of nano-particles on the wear resistance of the coatings were investigated. It was found that the addition of nano-TiC eliminates the macro-defects of Fe55 alloy coating. Meanwhile, the morphology and dispersion of TiC particles in coatings were affected by the content of nano-TiC and nano-CeO₂. Specifically, the addition of 1 wt% nano-CeO₂ facilitates to the formation of near-spherical tiny TiC particles with low agglomeration in the coating. Therefore, the Fe55 + 10 wt% nano-TiC+1 wt% nano-CeO₂ coating exhibits the best wear property among all the prepared Fe-based coatings. This paper provides theoretical guidance for the preparation of the modified Fe-based coating with excellent wear resistance.     

Inhibiting tribocorrosion damage of Cr/CrxN coatings by multi-layer design

The two-layer and multi-layer Cr/Cr_xN coatings were fabricated on 316 L stainless steel (316 L SS) substrates by the arc ion plating technique. The two-layer Cr/Cr_xN coating was a typical CrN coating with an adhesive Cr layer. And the multi-layer Cr/Cr_xN coating design was in two dimensions. In the first dimension, the multi-layer Cr/Cr_xN coating consisted of alternative Cr/CrN layers with the thickness ratio of 1:5; in the second dimension, the alternative Cr₂N layers with the thickness of 10 nm were inserted in CrN layers. This design was expected to increase transverse interfaces in a smaller scale. The microstructures, mechanical, corrosion and tribocorrosion performances of both Cr/Cr_xN coatings were systematically investigated. The results showed that the special multi-layer design of Cr/Cr_xN coatings improved mechanical, anti-corrosion and anti-tribocorrosion performances. Compared with the two-layer Cr/Cr_xN coating, the reduced tribocorrosion damage of the muti-layer Cr/Cr_xN coating was closely related to the inhibited synergistic effect between electrochemical corrosion and mechanical wear. In conclusion, the multi-layer Cr/Cr_xN coating was more suitable to work as the surface protective coating than the two-layer Cr/Cr_xN coating in seawater.     

Frictional behavior and wear resistance performance of gradient cermet composite tool materials sliding against hard materials

Gradient cermet composites possessing high surface hardness, flexural strength and interface bonding strength were fabricated using vacuum hot-pressing sintering. Ball-on-disk tests were performed to investigate the tribological properties of the gradient cermet composites against 440 C stainless steel, Al₂O₃ and Si₃N₄ balls at different sliding speed and load in comparison with traditional Ti(C,N) cermets. The tribological behavior was characterized in terms of friction coefficient and wear rate. The results showed that friction coefficient was significantly dependent on the sliding speed and load when sliding against Al₂O₃ and Si₃N₄. However, there was no obvious relation between them during sliding against 440 C stainless steel due to the formation of metal adhesive layer. Gradient cermet composites exhibited a higher friction coefficient but lower wear rate than traditional Ti(C,N) cermets. The main wear mechanism of gradient cermet composites was adhesion wear during sliding against 440 C stainless steel, while abrasion wear was the predominant mechanism during sliding against Al₂O₃ and Si₃N₄. It was expected that gradient cermet composites would be excellent candidates for cutting tool materials.