Effect of sintering time on crystal structure and microwave dielectric properties in aeschynite-structured (Sm1−xYx)(Ti1.5W0.5)O6 (x = 0 and 0.5) ceramics

The crystal structure and microwave dielectric properties of the (Sm_1−xY_x)(Ti_1.5W_0.5)O₆ (x = 0 and 0.5) ceramics sintered at 1375 °C for 2-50 h were investigated in this study. No secondary phase was observed in the samples sintered for various sintering times, whereas a secondary phase was formed in the (Sm_0.5Y_0.5)(Ti_1.5W_0.5)O₆ ceramic sintered at 1400 °C for 50 h. As for the microstructure analysis, the formation of the liquid phase was observed in the both of the samples sintered for 20 and 50 h. The formation of the liquid phase is related to the compositional change of Ti and W from the stoichiometric composition of the samples caused by the instability of crystal structure. The dielectric constants were increased with increased sintering time in the both of the samples, though variations in the temperature coefficient of resonant frequency of the samples were not recognized with the variation in the sintering time. Moreover, although the quality factors of the each sample increased with increasing the sintering time from 2 to 10 h, decreases in the quality factors were recognized when the sintering time was over 10 h.     

Effect of CuO on the sintering temperature and piezoelectric properties of lead-free 0.95(Na0.5K0.5)NbO3-0.05CaTiO3 ceramics

The addition of a small amount of CuO to the 0.95(Na_0.5K_0.5)NbO₃-0.05CaTiO₃ (0.95NKN-0.05CT) ceramics sintered at 960 °C for 10 h produced a dense microstructure with large grains due to the liquid phase sintering. Due to the negligible Na₂O evaporation, poling was easy for all specimens sintered at 960 °C. The piezoelectric properties of the specimens were considerably influenced by the relative density, grain size and liquid phase amount. The high piezoelectric properties of d₃₃ = 200 pC/N, k_p = 0.37, and Q_m = 350 were obtained for the 0.95NKN-0.05CT ceramics containing 2.0 mol% CuO sintered at 960 °C for 10 h. Therefore, the 0.95NKN-0.05CT ceramics containing a small amount of CuO are a good candidate material for lead-free piezoelectric ceramics.     

Microwave dielectric properties and microstructures of CuO- and ZnO-doped LaAlO3 ceramics

The microwave dielectric properties and the microstructures of 0.25 wt.% CuO-doped LaAlO₃ ceramics with ZnO additions have been investigated. The sintered LaAlO₃ ceramics are characterized by X-ray diffraction spectra and scanning electron microscopy (SEM). Tremendous reduction in sintering temperature can be achieved with the addition of sintering aids CuO and ZnO. The ceramic samples show that dielectric constants (ε_r) of 22−24 and Q×f values of 33,000−57,000 (at 9.7 GHz) can be obtained at low sintering temperatures 1340−1460°C. The temperature coefficient of resonant frequency varies from −24 to −48 ppm/°C. At the level of 0.25 wt.% CuO and 1 wt.% ZnO additions, LaAlO₃ ceramics possesses a dielectric constant (ε_r) of 23.4, a Q×f value of 57,000 (at 9.7 GHz) and a τ_f value of −38 ppm/°C at 1400°C for 2 h.     

Dielectric and pyroelectric anisotropy in melt-quenched BaBi2(Nb1 − xVx)2O9 ceramics

The (0 0 l) textured BaBi₂(Nb_1 − xV_x)₂O₉ (where x = 0, 0.03, 0.07, 0.1 and 0.13) ceramics were fabricated via the conventional melt-quenching technique followed by high temperature heat-treatment (800-1000 °C range). The influence of vanadium content and sintering temperature on the texture development and relative density were investigated. The samples corresponding to the composition x = 0.1 sintered at 1000 °C for 10 h exhibited the maximum orientation of about 67%. The Scanning electron microscopic studies revealed the presence of platy grains having the a-b planes perpendicular the pressing axis. The dielectric constant and the pyroelectric co-efficient values in the direction perpendicular to the pressing axis were higher. The anisotropy in the dielectric constant is about 100 (at 100 kHz) at the dielectric maximum temperature and anisotropy in the pyroelectric co-efficient is about 50 μC cm⁻² °C⁻¹ in the vicinity of pyroelectric anomaly for the sample corresponding to the composition x = 0.1 sintered at 1000 °C. Higher values of the dielectric loss and electrical conductivity were observed in the direction perpendicular to the pressing axis which is attributed to the high oxygen ion conduction in the a-b planes.     

Improved high-Q microwave dielectric resonator using CuO-doped MgNb2O6 ceramics

The microwave dielectric properties and the microstructures of MgNb₂O₆ ceramics with CuO additions (1-4 wt.%) prepared with conventional solid-state route have been investigated. The sintered samples exhibit excellent microwave dielectric properties, which depend upon the liquid phase and the sintering temperature. It is found that MgNb₂O₆ ceramics can be sintered at 1140 °C due to the liquid phase effect of CuO addition. At 1170 °C, MgNb₂O₆ ceramics with 2 wt.% CuO addition possesses a dielectric constant (ε_r) of 19.9, a Q×f value of 110,000 (at 10 GHz) and a temperature coefficient of resonant frequency (τ_f) of −44 ppm/°C. The CuO-doped MgNb₂O₆ ceramics can find applications in microwave devices requiring low sintering temperature.     

Structure and electrical properties of (1 − x)Bi0.5Na0.5TiO3-xBi0.5K0.5TiO3 ceramics near morphotropic phase boundary

The binary lead-free piezoelectric ceramics with the composition of (1 − x)Bi_0.5Na_0.5TiO₃-xBi_0.5K_0.5TiO₃ were synthesized by conventional mixed-oxide method. The phase structure transformed from rhombohedral to tetragonal phase in the range of 0.16 ≤ x ≤ 0.20. The grain sizes varied with increasing the Bi_0.5K_0.5TiO₃ content. Electrical properties of ceramics are significantly influenced by the Bi_0.5K_0.5TiO₃ content. Two phase transitions at T_t (the temperature at which the phase transition from rhombohedral to tetragonal occurs) and T_c (the Curie temperature) were observed in all the ceramics. Adding Bi_0.5K_0.5TiO₃ content caused the variations of T_t and T_c. A diffuse character was proved by the linear fitting of the modified Curie-Weiss law. Besides, the ceramics with homogeneous microstructure and excellent electrical properties were obtained at x = 0.18 and sintered at 1170 °C. The piezoelectric constant d₃₃, the electromechanical coupling factor K_p and the dielectric constant ?_r reached 144 pC/N, 0.29 and 893, respectively. The dissipation factor tan δ was 0.037.     

(5 − x)BaO-xMgO-2Nb2O5 ceramics prepared using a reaction-sintering process

(5 − x)BaO-xMgO-2Nb₂O₅ (x = 0.5 and 1; 5MBN and 10MBN) microwave ceramics prepared using a reaction-sintering process were investigated. Without any calcinations involved, the mixture of BaCO₃, MgO, and Nb₂O₅ was pressed and sintered directly. MBN ceramics were produced after 2-6 h of sintering at 1350-1500 °C. The formation of (BaMg)₅Nb₄O₁₅ was a major phase in producing 5MBN ceramics, and the formation of Ba(Mg_1/3Nb_2/3)O₃ was a major phase in producing 10MBN ceramics. As CuO (1 wt%) was added, the sintering temperature dropped by more than 150 °C. We produced 5MBN ceramics with these dielectric properties: ?_r = 36.69, Qf = 20,097 GHz, and τ_f = 61.1 ppm/°C, and 10MBN ceramics with these dielectric properties: ?_r = 39.2, Qf = 43,878 GHz, and τ_f = 37.6 ppm/°C. The reaction-sintering process is a simple and effective method for producing (5 − x)BaO-xMgO-2Nb₂O₅ ceramics for applications in microwave dielectric resonators.     

Dielectric properties of (1−x)(Mg0.95Co0.05)TiO3-xCaTiO3 ceramic system at microwave frequency

The microwave dielectric properties and the microstructures of the (1−x)MgTiO₃-xCaTiO₃ ceramic system were investigated. With partial replacement of Mg by Co, dielectric properties of the (1−x)(Mg_0.95Co_0.05)TiO₃-xCaTiO₃ ceramics can be promoted. The microwave dielectric properties are strongly correlated with the sintering temperature. At 1275°C, the 0.95(Mg_0.95Co_0.05)TiO₃-0.05CaTiO₃ ceramics possesses excellent microwave dielectric properties: a dielectric constant ε_r of 20.3, a Q×f value of 107 000 ( at 7 GHz) and a τ_f value of −22.8 ppm/°C. By appropriately adjusting the x value in the (1−x)(Mg_0.95Co_0.05)TiO₃-xCaTiO₃ ceramic system, zero τ_f value can be achieved. With x=0.07, a dielectric constant ε_γ of 21.6, a Q×f value of 92 000 (at 7 GHz) and a τ_f value of −1.8 ppm/°C was obtained for 0.93(Mg_0.95Co_0.05)TiO₃-0.07CaTiO₃ ceramics sintered at 1275°C for 4 h.     

Study on properties of BaxSmyTi7O20 ceramics with CaO-SiO2-B2O3 glass

The effect of CaO-SiO₂-B₂O₃ (CSB) glass addition on the sintering temperature and dielectric properties of Ba_xSm_yTi₇O₂₀ ceramics has been investigated using X-ray diffraction, scanning electron microscopy and differential thermal analysis. The CSB glass starts to melt at about 970 °C, and a small amount of CSB glass addition to Ba_xSm_yTi₇O₂₀ ceramics can greatly decrease the sintering temperature from about 1350 to about 1260 °C, which is attributed to the formation of liquid phase. It is found that the dielectric properties of Ba_xSm_yTi₇O₂₀ ceramics are dependent on the amount of CSB glass and the microstructures of sintered samples. The product with 5 wt% CSB glass sintered at 1260 °C is optimal in these samples based on the microstructure and the properties of sintering product, when the major phases of this material are BaSm₂Ti₄O₁₂ and BaTi₄O₉. The material possesses excellent dielectric properties: ?_r = 61, tan δ = 1.5 × 10⁻⁴ at 10 GHz, temperature coefficient of dielectric constant is −75 × 10⁻⁶ °C⁻¹.     

Influence of Bi2O3 and CuO addition on low-temperature sintering and dielectric properties of Ba0.6Sr0.4TiO3 ceramics

In this study, we tried to lower the sintering temperature of Ba_0.6Sr_0.4TiO₃ (BST) ceramics by several kinds of adding methods of Bi₂O₃, CuO and CuBi₂O₄ additives. The effects of different adding methods on the microstructures and the dielectric properties of BST ceramics have been studied. In the all additive systems, the single addition of CuBi₂O₄ was the most effective way for lowering the sintering temperature of BST. When CuBi₂O₄ of 0.6 mol% was mixed with starting BST powders and sintered at 1100 °C, the derived ceramics demonstrated dense microstructure with a low dielectric constant (? = 4240), low dielectric loss (tan δ = 0.0058), high tunability (Tun = 38.3%) and high Q value (Q = 251). It was noteworthy that the sintering temperature was significantly lowered by 350 °C compared with no-additive system, and the derived ceramics maintained the excellent microwave dielectric properties corresponding to pure BST.     

Dielectric properties of B2O3-doped (1 − x)LaAlO3-xSrTiO3 ceramic system at microwave frequency

The effects of B₂O₃ addition on the microwave dielectric properties and the microstructures of (1−x)LaAlO₃-xSrTiO₃ ceramics prepared by conventional solid-state routes have been investigated. Doping with 0.25 wt.% B₂O₃ can effectively promote the densification and the microwave dielectric properties of (1−x)LaAlO₃-xSrTiO₃ ceramics. It is found that LaAlO₃-SrTiO₃ ceramics can be sintered at 1400°C due to the liquid phase effect of a B₂O₃ addition observed by scanning electronic microscopy (SEM). The dielectric constant as well as the Q×f value decreases with increasing B₂O₃ content. At 1460°C, 0.46LaAlO₃-0.54SrTiO₃ ceramics with 0.25 wt.% B₂O₃ addition possesses a dielectric constant (ε_r) of 35, a Q×f value of 38,000 (at 7 GHz) and a temperature coefficients of resonant frequency (τ_f) of −1 ppm/°C.     

Preparation and properties of negative thermal expansion Zr2WP2O12 ceramics

Using solid-state reaction method, Zr₂WP₂O₁₂ powder was synthesized for this study. The optimum heating condition was 1200 °C for 4 h. The obtained powder was compacted and sintered. The relative density of the Zr₂WP₂O₁₂ ceramics with no sintering additive was 60%. That of samples sintered with more than 0.5 mass% MgO was about 97%. The average grain size (D₅₀), as estimated from the polished surface of a sample sintered at 1200 °C for 4 h was about 1 μm. The obtained ceramics showed a negative thermal expansion coefficient of about −3.4 × 10⁻⁶ °C⁻¹. Young's modulus, Poisson's ratio, three-point bending strength, Vickers microhardness, and fracture toughness of the obtained ceramics were, respectively, 74 GPa, 0.25, 113 ± 13 MPa, 4.4 GPa and 2.3 MPa m^1/2.     

Synthesis of (1 − x)Ca2/5Sm2/5TiO3-xLi1/2Nd1/2TiO3 ceramic powder via ethylenediaminetetraacetic acid precursor

(1 − x)Ca_2/5Sm_2/5TiO₃-xLi_1/2Nd_1/2TiO₃ (CSLNT) ceramic powder was prepared by a liquid mixing method using ethylenediaminetetraacetic acid (EDTA) as the chelating agent. TG, DTA, XRD and TEM characterized the precursors and derived oxide powders. When x = 0.3, perovskite CSLNT was synthesized at 1000 °C for 3 h in air. The CSLNT (x = 0.3) ceramics sintered at 1200 °C for 3 h show excellent microwave dielectric properties of ?_r = 99, Q_f = 6200 GHz and τ_f = 9 × 10⁻⁶ °C⁻¹.     

Low-temperature sintering of temperature-stable LaNbO4 microwave dielectric ceramics

We demonstrate the correlation between sintering behavior and microstructural observations in low-temperature sintered, LaNbO₄ microwave ceramics. Small CuO additions to LaNbO₄ significantly lowered the sintering temperature from 1250 to 950 °C. To elucidate the sintering mechanism, the internal microstructure of the sample manipulated by a focused ion beam (FIB) was investigated using transmission electron microscopy (TEM) and energy-dispersive spectroscopy (EDS). LaNbO₄ with 3 wt% CuO sintered at 950 °C for 2 h possessed the following excellent microwave dielectric properties: a quality factor (Qxf) of 49,000 GHz, relative dielectric constant (?_r) of 19.5, and temperature coefficient of resonant frequency (τ_f) of 1 ppm/°C. The ferroelastic phase transformation was also investigated using in situ X-ray diffraction (XRD) to explain the variation of τ_f in low-temperature sintered LaNbO₄ as a function of CuO content.     

Structural, spectroscopic and dielectric investigations on Ba8Zn(Nb6−xSbx)O24 microwave ceramics

Ba₈Zn(Nb_6−xSb_x)O₂₄ (x = 0, 0.3, 0.6, 0.9, 1.2, 1.5, 1.8 and 2.4) ceramics were prepared through the conventional solid-state route. The materials were calcined at 1250 °C and sintered in the range 1400-1425 °C. The structure of the system was analyzed by X-ray diffraction, Fourier transform infrared and Raman spectroscopic methods. The theoretical and experimental densities were calculated. The microstructure of the sintered pellets was analyzed using scanning electron microscopy. The low frequency dielectric properties were studied in the frequency range 50 Hz-2 MHz. The dielectric constant (?_r), temperature coefficient of resonant frequency (τ_f) and the unloaded quality factor (Q_u) are measured in the microwave frequency region using cavity resonator method. The τ_f values of the samples reduced considerably with the increase in Sb concentration. The materials have intense emission lines in the visible region. The compositions have good microwave dielectric properties and photoluminescence and hence are suitable for dielectric resonator and ceramic laser applications.     

Microwave dielectric properties and microstructures of the 11Li2O-3Nb2O5-12TiO2 ceramics with B2O3 addition

The effects of B₂O₃ addition, as a sintering agent, on the sintering behavior, microstructure and microwave dielectric properties of the 11Li₂O-3Nb₂O₅-12TiO₂ (LNT) ceramics have been investigated. With the low-level doping of B₂O₃ (≤2 wt.%), the sintering temperature of the LNT ceramic could be effectively reduced to 900 °C. The B₂O₃-doped LNT ceramics are also composed of Li₂TiO₃ss and “M-phase” phases. No other phase could be observed in the 0.5-2 wt.% B₂O₃-doped ceramics sintered at 840-920 °C. The addition of B₂O₃ induced no obvious degradation in the microwave dielectric properties but increased the τ_f values. Typically, the 0.5 wt.% B₂O₃-doped ceramics sintered at 900 °C have better microwave dielectric properties of ?_r = 49.2, Q × f = 8839 GHz, τ_f = 57.6 ppm/°C, which suggest that the ceramics could be applied in multilayer microwave devices requiring low sintering temperatures.     

Tantalum influence on physical properties of (K0.5Na0.5)(Nb1−xTax)O3 ceramics

Lead-free (K_0.5Na_0.5)(Nb_1−xTa_x)O₃ ceramics with x = 0.00-0.30 were prepared by the solid-state reaction technique. The effects of Ta on microstructure, crystallographic structure, phase transition and piezoelectric properties have been investigated. It has been shown that the substitution of Ta decreases Curie temperature T_C and orthorhombic-tetragonal phase transition temperature T_O-T, while increasing the rhombohedral-orthorhombic phase transition temperature T_R-O. In addition, piezoelectric activity is enhanced with the increase of Ta content. The ceramics with x = 0.30 have the high value of piezoelectric coefficient d₃₃ = 205 pC/N. Moreover, k_p shows little temperature dependence between −75° C and 75 °C, and d₃₃ exhibits very good thermal stability over the range from −196 °C to 75 °C in the aging test.     

Effect of the sintering temperature on the properties of Ce0.85La0.10Ca0.05O2−δ electrolyte material

Rare earth and alkaline earth co-doped Ce_0.85La_0.10Ca_0.05O_2−δ electrolyte material with the powder obtained by solid-state reaction method was sintered at 1300, 1400, 1500 and 1600 °C respectively. The results showed that the ionic conductivity of the sample sintered at 1400 °C was slightly lower compared to that sintered at 1500 °C in the temperature range of 300-550 °C, while the sample sintered at 1400 °C showed the highest ionic conductivity in all the samples above 550 °C. The ionic conductivity of ∼0.021 S/cm at 600 °C and the relative density of 98.2% were observed for the sample sintered at 1400 °C. In addition, the highest flexural strength with 145 MPa was also obtained for the sample sintered at 1400 °C. It suggested that the sintering temperature for Ce_0.85La_0.10Ca_0.05O_2−δ electrolyte may be reduced to as low as 1400 °C with desired properties.     

Microstructure and microwave dielectric characteristics of (1 − x)Ba(Zn1/3Ta2/3)O3-xBaTi4O9 ceramics

(1 − x)Ba(Zn_1/3Ta_2/3)O₃-xBaTi₄O₉ (0.1 ≤ x ≤ 0.85) composites are prepared by mixing 1150 °C-calcined BaTi₄O₉ with 1150 °C-calcined Ba(Zn_1/3Ta_2/3)O₃ powders. The crystal structure, microwave dielectric properties and sinterabilites of the (1 − x)Ba(Zn_1/3Ta_2/3)O₃-xBaTi₄O₉ ceramics have been investigated. X-ray diffraction patterns reveal that BaTi₄O₉, ordered and disordered Ba(Zn_1/3Ta_2/3)O₃ phases exist independently over the whole compositional range. The sintering temperatures of (1 − x)Ba(Zn_1/3Ta_2/3)O₃-xBaTi₄O₉ ceramics are about 1240 - 1320 °C and obviously lower than those of Ba(Zn_1/3Ta_2/3)O₃ ceramics. The dielectric constants (?_r) and the temperature coefficient of resonant frequency (τ_f) of (1 − x)Ba(Zn_1/3Ta_2/3)O₃-xBaTi₄O₉ ceramics increase with the increase of BaTi₄O₉ content. Nevertheless, the bulk densities and the quality values (Q × f) of (1 − x)Ba(Zn_1/3Ta_2/3)O₃-xBaTi₄O₉ ceramics increase with the increase of Ba(Zn_1/3Ta_2/3)O₃ content. The results are attributed to the higher density and quality value of Ba(Zn_1/3Ta_2/3)O₃ ceramics, the better grain growth, and the densification of sintered specimens added a small BaTi₄O₉ content. The (1 − x)Ba(Zn_1/3Ta_2/3)O₃-xBaTi₄O₉ ceramic with x = 0.1 sintered at 1320 °C exhibits a ?_r value of 31.5, a maximum Q × f value of 68500 GHz and a minimum τ_f value of 4.1 ppm/°C.     

Preparation, structure and dielectric properties of Ba4LaMNb3O15 (M = Ti, Sn ) ceramics

Two new cation-deficient hexagonal perovskites Ba₄LaMNb₃O₁₅ (M = Ti, Sn) ceramics were prepared by high temperature solid-state reaction route. The phase and structure of the ceramics were characterized by X-ray diffraction, scanning electron microscopy (SEM). The microwave dielectric properties of the ceramics were studied using a network analyzer. The Ba₄LaTiNb₃O₁₅ has high dielectric constant of 52, high quality factors (Q) 3500 (at 4.472 GHz), and temperature variation of resonant frequency (τ_f) +93 ppm °C⁻¹ at room temperature; Ba₄LaSnNb₃O₁₅ has dielectric constant of 39 with high Q value of 2510 (at 5.924 GHz), and τ_f −29 ppm °C⁻¹.