A hydroxylamine electrochemical sensor based on electrodeposition of porous ZnO nanofilms onto carbon nanotubes films modified electrode

A novel route (electrodeposition) for the fabrication of porous ZnO nanofilms attached multi-walled carbon nanotubes (MWCNTs) modified glassy carbon electrodes (GCEs) was proposed. The morphological characterization of ZnO/MWCNT films was examined by scanning electron microscopy (SEM) and X-ray powder diffraction (XRD). The performances of the ZnO/MWCNTs/GCE were characterized with cyclic voltammetry (CV), Nyquist plot (EIS) and typical amperometric response (i-t). The potential utility of electrodes constructed was demonstrated by applying them to the analytical determination of hydroxylamine concentration. An optimized limit of detection of 0.12 μM was obtained at a signal-to-noise ratio of 3 and with a fast response time (within 3 s). Additionally, the ZnO/MWCNTs/GCE exhibited a wide linear range from 0.4 to 1.9 × 10⁴ μM and higher sensitivity. The ease of fabrication, high stability, and low cost of the modified electrode are the promising features of the proposed sensor.     

Towards the conception of an amperometric sensor of l-tyrosine based on Hemin/PAMAM/MWCNT modified glassy carbon electrode

A novel amperometric sensor was fabricated based on the immobilization of hemin onto the poly (amidoamine)/multi-walled carbon nanotube (PAMAM/MWCNT) nanocomposite film modified glassy carbon electrode (GCE). Electrochemical impedance spectroscopy (EIS), cyclic voltammetry (CV) and ultraviolet visible (UV-vis) adsorption spectroscopy were used to investigate the possible state and electrochemical activity of the immobilized hemin. In the Hemin/PAMAM/MWCNT nanocomposite film, MWCNT layer possessed excellent inherent conductivity to enhance the electron transfer rate, while the layer of PAMAM greatly enlarged the surface average concentration of hemin (Γ) on the modified electrode. Therefore, the nanocomposite film showed enhanced electrocatalytical activity towards the oxidation of l-tyrosine. The kinetic parameters of the modified electrode were investigated. In pH 7.0 phosphate buffer solution (PBS), the sensor exhibits a wide linear range from 0.1 μM to 28.8 μM l-tyrosine with a detection limit of 0.01 μM and a high sensitivity of 0.31 μA μM⁻¹ cm⁻². In addition, the response time of the l-tyrosine sensor is less than 5 s. The excellent performance of the sensor is largely attributed to the electro-generated high reactive oxoiron (IV) porphyrin (O = Fe^IV-P) which effectively catalyzed the oxidation of l-tyrosine. A mechanism was herein proposed for the catalytic oxidation of l-tyrosine by oxoiron (IV) porphyrin complexes.     

Electrochemical behavior of an indenedione derivative electrodeposited on a renewable sol-gel derived carbon ceramic electrode modified with multi-wall carbon nanotubes: Application for electrocatalytic determination of hydrazine

A novel modified carbon ceramic electrode (CCE) containing multi-wall carbon nanotubes (MWCNTs) was fabricated by a sol-gel technique. The prepared MWCNT-CCE was modified by the electrodeposition of an indenedione derivative. The indenedione modified MWCNT-CCE (IMWCNT-CCE) shows one pair of peaks with surface confined characteristics. According to the theoretical model of Laviron, estimations were made in different pHs of the surface charge transfer rate constant, k_s, and the charge transfer coefficient, α, for electron transfer between the indenedione derivative and MWCNT-CCE. The modified electrode shows a highly catalytic activity toward hydrazine electrooxidation at a wide pH range (5-9). The kinetic parameters such as the electron transfer coefficient, α, the heterogeneous rate constant, k′, and the exchange current of hydrazine at the IMWCNT-CCE were calculated as 0.29 ± 0.01, 2.7(±0.3) × 10⁻³ cm s⁻¹ and 0.17 ± 0.03 μA, respectively. Also, the modified electrode shows an excellent analytical performance for voltammetric determination of hydrazine. Differential pulse voltammetry (DPV) exhibits two linear dynamic ranges, 0.6-8.0 μM and 8.0-100.0 μM, and a lower detection limit of 0.29 μM for hydrazine. Finally, the practical analytical utility is illustrated by differential pulse voltammetric determination of hydrazine in auxiliary cooling water at IMWCNT-CCE and the accuracy of the results is verified in comparison with those obtained from the standard ASTM method.     

Bilirubin oxidase bound to multi-walled carbon nanotube-modified gold

We report on direct electron transfer (DET) reactions of bilirubin oxidase at multi-walled carbon nanotube-(MWCNT) modified gold electrodes. MWCNTs are very suitable for protein immobilisation and provide surface groups that can be used for the stable fixation on electrodes. They can also effectively replace the natural substrate of BOD - bilirubin, the electron donor for oxygen reduction. The bioelectrocatalytic oxygen reduction was recorded using linear sweep voltammetry (LSV) with BOD covalently linked to the nanotubes. The start potential of the bioelectrocatalytic oxygen reduction at pH 7 and a scan rate of 10 mV/s was determined to be 485 ± 10 mV vs. Ag/AgCl, 1 M KCl (720 mV vs. SHE). Current densities up to 500 μA/cm² were detected in an air-saturated buffer at room temperature (25 ± 5 °C). Experiments with a rotating disk electrode (RDE) indicate a diffusion controlled electrode reaction. A k_s value in the range of 80-100 s⁻¹ could be estimated.The DET could also be observed directly by the redox conversion of a copper centre of BOD under anaerobic conditions. A peak pair with a formal potential of 680 ± 10 mV vs. SHE was found. The T1 site is probably addressed by the electrode as indicated by several experimental studies.     

Electrocatalysis of asulam on cobalt phthalocyanine modified multi-walled carbon nanotubes immobilized on a basal plane pyrolytic graphite electrode

This work describes the electrochemical properties of cobalt tetra-aminophthalocyanine (CoTAPc) complex electropolymerized at the surface of multi-walled carbon nanotube (MWCNT) abrasively immobilized onto a basal plane pyrolytic graphite electrode (BPPGE). The constructed electrode displayed excellent electrocatalytic behaviour towards the oxidation of the herbicide, asulam, as evidenced by the enhancement of the oxidation peak current (∼6 times) and the shift in the oxidation potential to lower values (by ∼120 mV) in comparison with the bare BPPGE. The chronoamperometric detection of asulam which was carried out in 0.10 M phosphate buffer (pH 7.0) at a fixed potential of 0.65 V (versus Ag|AgCl) yielded excellent analytical parameters; a linear concentration range of 4.5-20 μM, a sensitivity of 241 × 10⁻³ μA/μM, a detection limit of 1.15 μM asulam (using the Y_B + 3σ criterion) and a response time of ∼2 s.     

Renewable-surface sol-gel derived carbon ceramic-modified electrode fabricated by a newly synthesized polypyridil and phosphine Ru (II) complex and its application as an amperometric sensor for hydrazine

A chemically modified carbon ceramic composite electrode (CCE) containing Dichloro{(8, 9-dimethyl-dipyridio [2,3-a;2′,3′-c] phenazine-κ²-N,N′) bis(triphenylphosphine-κ-P)}ruthenium (II) complex which synthesized newly was constructed by the sol-gel technique. Electrochemical behavior and stability of modified CCE were investigated by cyclic voltammetry. The electrocatalytic activity of CCE was investigated and showed a good effect for oxidation of hydrazine in phosphate buffer solution (PBS). A linear concentration range of 6 μM to 1.2 mM of hydrazine with an experimental detection limit of 1 μM of hydrazine was obtained. The diffusion coefficient of hydrazine and its catalytic rate constant for electrocatalytic reaction along with the apparent electron transfer rate constant (k_s) and transfer coefficient (α) were also determined.The modified carbon ceramic electrode doped with this new Ru-complex showed good reproducibility, short response time (t < 2 s), remarkable long-term stability (>3 month) and especially good surface renewability by simple mechanical polishing.The results showed that this electrode could be used as an electrochemical sensor for determination of hydrazine in real water samples used in Fars Power Plant Station, including its heat recovery steam generator (HRSG) water (at different operational condition), cooling system and clean waste water.     

Poly-phenothiazine derivative-modified glassy carbon electrode for NADH electrocatalytic oxidation

Electropolymerization of a new phenothiazine derivative (bis-phenothiazin-3-yl methane; BPhM) on glassy carbon (GC) electrode generates a conducting film of poly-BPhM, in stable contact with the electrode surface. The heterogeneous electron-transfer process corresponding to the modified electrode is characterized by a high rate constant (50.4 s⁻¹, pH 7). The GC/poly-BPhM electrode shows excellent electrocatalytic activity toward NADH oxidation. The rate constant for catalytic NADH oxidation, estimated from rotating disk electrode (RDE) measurements and extrapolated to zero concentration of NADH, was found to be 9.4 × 10⁴ M⁻¹ s⁻¹ (pH 7). The amperometric detection of NADH, at +200 mV vs. SCE, is described by the following electroanalytical parameters: a sensitivity of 1.82 mA M⁻¹, a detection limit of 2 μM and a linear domain up to 0.1 mM NADH.     

Novel amperometric glucose biosensor based on an ether-linked cobalt(II) phthalocyanine-cobalt(II) tetraphenylporphyrin pentamer as a redox mediator

The development of cobalt(II) phthalocyanine-cobalt(II) tetra(5-phenoxy-10,15,20-triphenylporphyrin), (CoPc-(CoTPP)₄) pentamer as a novel redox mediator for amperometric enzyme electrode sensitive to glucose is described. A glassy carbon electrode (GCE) was first modified with the pentamer, then followed by the immobilization onto the GCE-CoPc-(CoTPP)₄ with glucose oxidase (GOx) through cross-linking with glutaraldehyde in the presence of bovine serum albumin (BSA) and Nafion^® cation-exchange polymer. The proposed biosensor displayed good amperometric respose charateristics to glucose in pH 7.0 PBS solution; such as low overpotentials (+400 mV versus Ag|AgCl), very fast amperometric response time (∼5 s), linear concentration range extended up to 11 mM, with 10 μM detection limit. The biosensor exhibited electrochemical Michaelis-Menten kinetics and showed an average apparent Michaelis-Menten constant (K^′M) of 14.91 ± 0.46 mM over a storage period of 2 weeks.     

Redox polymer covalently modified multiwalled carbon nanotube based sensors for sensitive acetaminophen and ascorbic acid detection

A sensitive electrochemical detection method was developed involving multiwalled carbon nanotubes (MWCNTs) covalently modified with osmium-based redox polymer. The polycationic redox polymer, poly[4-vinylpyridine Os(bipyridine)₂Cl]-co-ethylamine (POs-EA), was first synthesized and covalently attached to MWCNTs. The redox polymer modified MWCNTs were then trapped in a hydrogel formed from polyethyleneglycol diacrylate (PEG-DA) using 1-phenyl-2-hydroxy-2-methyl-1-propanone as a photoinitiator. Upon exposure to aqueous media, the gel swelled to allow movement of analytes in and out of the gel without having any effect on the redox polymer modified nanotube signal. Cyclic voltammetry showed reversible pairs of oxidation-reduction peaks at 0.35 V (vs Ag/AgCl) corresponding to the Os^II/Os^III. This assembly was able to catalytically oxidize both acetaminophen and ascorbic acid (AA). Amperometric data showed a linearity between 0 and 100 μM (R² of 0.999, n = 10) 0.5 mV vs Ag/AgCl (sensitivity 0.003 μA/μM) for ascorbic acid, while for acetaminophen the linearity was between 0 and 1.5 μM (R² of 0.9999, n = 8) with a sensitivity of 65 μA/μM. This sensing system was found to exhibit remarkable stability over several weeks with excellent reproducibility.     

Detection of hydrazine based on Nano-Au deposited on Porous-TiO2 film

The fabrication of Nano-Au/Porous-TiO₂ composite modified glassy carbon electrode (GCE) and its application in the determination of hydrazine were proposed. The morphological characterization was examined by transmission electron microscope and scanning electron microscopy. The Nano-Au/Porous-TiO₂/GCE exhibited a wide linear range of hydrazine from 2.5 to 500 μM, with a detection limit of 0.5 μM at a signal-to-noise ratio of 3 and with a fast response time (within 3 s). Furthermore, the reaction mechanism of the hydrazine on the Nano-Au/Porous-TiO₂/GCE was explored. The ease of fabrication, high stability, and low cost of the modified electrode are the promising features of the proposed sensor.     

Modification of glassy carbon electrode with multi-walled carbon nanotubes and iron(III)-porphyrin film: Application to chlorate, bromate and iodate detection

In this study, multi-wall carbon nanotubes (MWCTs) is evaluated as a transducer, stabilizer and immobilization matrix for the construction of amperometric sensor based on iron-porphyrin. 5,10,15,20-Tetraphenyl-21H,23H-porphine iron(III) chloride (Fe(III)P) adsorbed on MWCNTs immobilized on the surface of glassy carbon electrode. Cyclic voltammograms of the Fe(III)P-incorporated-MWCNTs indicate a pair of well-defined and nearly reversible redox couple with surface confined characteristics at wide pH range (2-12). The surface coverage (Γ) and charge transfer rate constant (k_s) of Fe(III)P immobilized on MWCNTs were 7.68 × 10⁻⁹ mol cm⁻² and 1.8 s⁻¹, respectively, indicating high loading ability of MWCNTs for Fe(III)P and great facilitation of the electron transfer between Fe(III)P and carbon nanotubes immobilized on the electrode surface. Modified electrodes exhibit excellent electrocatalytic activity toward reduction of ClO₃⁻, IO₃⁻ and BrO₃⁻ in acidic solutions. The catalytic rate constants for catalytic reduction of bromate, chlorate and iodate were 6.8 × 10³, 7.4 × 10³ and 4.8 × 10² M⁻¹ s⁻¹, respectively. The hydrodynamic amperometry of rotating-modified electrode at constant potential versus reference electrode was used for detection of bromate, chlorate and iodate. The detection limit, linear calibration range and sensitivity for chlorate, bromate and iodate detections were 0.5 μM, 2 μM to 1 mM, 8.4 nA/μM, 0.6 μM, 2 μM to 0.15 mM, 11 nA/μM, and 2.5 μM, 10 μM to 4 mM and 1.5 nA/μM, respectively. Excellent electrochemical reversibility of the redox couple, good reproducibility, high stability, low detection limit, long life time, fast amperometric response time, wide linear concentration range, technical simplicity and possibility of rapid preparation are great advantages of this sensor. The obtained results show promising practical application of the Fe(III)P-MWCNTs-modified electrode as an amperometric sensor for chlorate, iodate and bromate detections.     

Study of nimesulide and its determination using multiwalled carbon nanotubes modified glassy carbon electrodes

A new method for the determination of nimesulide was established based on the multiwalled carbon nanotubes (MWCNTs) modified glassy carbon electrode (MWCNTs/GCE). In 0.2 M PBS (pH 6.6) buffer solution, the MWCNTs/GCE showed a remarkable catalytic and enhancement effect on reduction of the nimesulide. The reduction peak potential of nimesulide shifted positively from −0.665 V at bare GCE to −0.553 V at MWCNTs/GCE, and the sensitivity increased ca. 7 times. A linear dynamic range of 3.2 × 10⁻⁷-6.5 × 10⁻⁵ M (R = 0.9992) with a detection limit of 1.6 × 10⁻⁷ M was obtained. The electrochemical behaviors of nimesulide were studied and electron-transfer coefficient (α = 0.45), proton number (X = 1) and electron-transfer number (n = 2) have been determined. This method has been used to determine the content of nimesulide in medical tablets. The recovery was determined to be 93.2-106.2% by means of standard addition method. Compared with UV-vis spectrometry, the method was not remarkable difference.     

Electrochemical synthesis of belt-like polyaniline network on p-phenylenediamine functionalized glassy carbon electrode and its use for the direct electrochemistry of horse heart cytochrome c

Three-dimension (3D) belt-like polyaniline (PAN) network has been prepared via electrochemical polymerization of aniline on p-phenylenediamine (PDA) functionalized glassy carbon electrode (GCE) using a three-step electrochemical deposition procedure. PDA was covalently binded on GCE via the formation of carbon-nitrogen bond between amine cation radical and the aromatic moiety of GCE surface using electrochemical oxidation procedure. X-ray photo-electron spectroscopy (XPS) and cyclic voltammetry have been performed to characterize the attachment of PDA on GCE. The images of scanning electron microscope (SEM) show that the 3D belt-like PAN network is uniform. The width and thickness of the PAN belt varies in the range of 1.5-5.5 μm and 0.1-0.8 μm, respectively. The distance between the belt-contacts ranges from 2.5 to 15 μm. The 3D belt-like PAN network modified GCE (PAN-PDA/GCE) exhibits an improved electro-activity of PAN at an extended pH up to 7.0. The PAN-PDA/GCE not only immobilizes but also leads to a direct electrochemical behavior of cytochrome c (Cyt c). The immobilized Cyt c maintains its activity, showing a surface-controlled electrode process with the electron-transfer rate constant (k_s) of 14.8 s⁻¹ and electron-transfer coefficient (α) of 0.48, and could be used for the electrocatalytic reduction of hydrogen peroxide (H₂O₂).     

Preparation and electrocatalytic oxidation properties of a nickel pentacyanonitrosylferrate modified carbon composite electrode by two-step sol-gel technique: improvement of the catalytic activity

The sol-gel technique was used to construct nickel pentacyanonitrosylferrate (NiPCNF) modified composite ceramic carbon electrodes (CCEs). This involves two steps: forming a CCE containing Ni powder and then immersing the electrode into a sodium pentacyanonitrosyl-ferrate solution (electroless deposition). The cyclic voltammograms of the resulting surface modified CCE under optimum conditions show a well-defined redox couple due to the [Ni^IIFe^III/II(CN)₅NO]^0/−1 system. The electrochemical properties and stability of the modified electrode were investigated by cyclic voltammetry. The apparent electron transfer rate constant (k_s) and transfer coefficient (α) were determined by cyclic voltammetry being about 1.1 s⁻¹ and 0.55, respectively. Sulfite has been chosen as a model to elucidate the electrocatalytic ability of NiPCNF-modified CCE prepared by one- or two-step sol-gel technique. The modified electrode showed excellent electrocatalytic activity toward the SO₃²⁻ electro oxidation in pH range 3-9 in comparison with CCE modified by homogeneous mixture of graphite powder, Ni(NO₃)₂ and Na₂[Fe(CN)₅NO] (one-step sol-gel technique). Sulfite was determined amperometrically at the surface of this modified electrode in pH 7. Under the optimized conditions the calibration curve is linear in the concentration range 2 μM to 2.0 mM. The detection limit (signal-to-noise is 3) and sensitivity are 0.5 μM and 13.5 nA/μM. The modified carbon ceramic electrode containing nickel pentacyanonitrosylferrate shows good repeatability, short response time, t (90%) <2 s, long-term stability (3 months), and it is renewed by simple mechanical polishing and its immersing in Na₂[Fe(CN)₅NO] solution. The advantages of the SO₃²⁻ amperometrically detector based on the nickel pentacyanonitrosylferrate-doped CCE is high sensitivity, inherent stability at wide pH range, excellent catalytic activity and less expense and simplicity of preparation. This sensor can be used as amperometric detector in chromatographic instruments.     

Voltammetric determination of bisoprolol fumarate in pharmaceutical formulations and urine using single-wall carbon nanotubes modified glassy carbon electrode

The electrochemistry of bisoprolol fumarate (BF) has been investigated by differential pulse voltammetry at a single-wall carbon nanotubes (SWNTs) modified glassy carbon electrode (GCE). The prepared electrode showed an excellent electrocatalytic activity towards the oxidation of BF leading to a marked improvement in sensitivity as compared to bare glassy carbon electrode where electrochemical activity for the analyte cannot be observed. The SWNTs-modified GCE exhibited a sharp anodic peak at a potential of ∼950 mV for the oxidation of BF. Under optimum conditions linear calibration curve was obtained over the BF concentration range 0.01-0.1 mM in 0.5 M phosphate buffer solution (pH 7.2) with a correlation coefficient of 0.9789 and detection limit of 8.27 × 10⁻⁷ M. The modified electrode has been applied for the drug determination in human urine with no prior extraction and in commercial tablets. The proposed method has also been validated.     

Electrochemistry and voltammetric determination of furazolidone with a multi-walled nanotube composite film-glassy carbon electrode

This study describes the electrochemical properties of furazolidone (Fu) at a glassy carbon electrode (GCE) modified with a multi-walled carbon nanotube (MWCNT) composite film. Cyclic voltammetry and chronoamperometry techniques were used for diagnostic purposes. The electrode (MWCNT-film-modified GCE) exhibited excellent electrocatalytic behavior for the reduction of Fu as evidenced by the enhancement of the 4e-reduction peak current and the shift in the reduction potential to more positive potential (by 50 mV) in comparison with a bare GCE. The formal potential, E ^0′, of Fu is pH dependent with a slope of 54.4 mV per unit of pH, close to the anticipated Nernestian value of −59 mV for a four-electron and four-proton processes. The transfer coefficient (α), standard rate constant of the surface reaction (k _s), diffusion coefficient (D), and surface concentration (Γ) for the MWCNT-film-modified GCE were calculated. On the other hand, Fu can be accumulated effectively on the MWCNT-film-modified GCE. Under the selected experimental conditions, i.e., solution pH 6, accumulation time 10 min, and accumulation potential −0.30 V, the peak current shows a dynamic linear range 3–800 μM with detection limit 2.30 μM. The method was successfully applied to analyze pharmaceutical formulations. The method used in this study was further applied for the determination of Fu.     

An unusual H2O2 electrochemical sensor based on Ni(OH)2 nanoplates grown on Cu substrate

In this work, Ni(OH)₂ nanoplates grown on the Cu substrate were synthesized and characterized by scanning electron microscopy (SEM), X-ray powder diffraction (XRD), and X-ray photoelectron spectroscopy (XPS). Then a novel Cu-Ni(OH)₂ modified glass carbon electrode (Cu-Ni(OH)₂/GCE) was fabricated and evaluated by electrochemical impedance spectroscopy (EIS), cyclic voltammetry (CV), and typical amperometric response (i-t) method. Exhilaratingly, the Cu-Ni(OH)₂/GCE shows significant electrocatalytic activity toward the reduction of H₂O₂. At an applied potential of −0.1 V, the sensor produces an ultrahigh sensitivity of 408.1 μA mM⁻¹ with a low detection limit of 1.5 μM (S/N = 3). The response time of the proposed electrode was less than 5 s. What's more, the proposed sensor displays excellent selectivity, good stability, and satisfying repeatability.     

Glucose biosensor based on multiwalled carbon nanotubes grown directly on Si

An amperometric biosensor based on covalent immobilization of glucose oxidase (GOx) on multiwalled carbon nanotubes (MWCNTs) with potassium ferricyanide as the redox mediator was developed. The MWCNTs were grown directly on a layered structure of Co/Ti/Cr on a SiO₂/Si substrate by microwave-heated chemical vapor deposition. The mediator helps to shuttle the electrons between the immobilized GOx and the MWCNT electrode, therefore operating at a potential of 0.25 V vs. the saturated calomel electrode. This potential precludes the interfering compounds from oxidization. The sensitivity of biosensors to glucose was found to depend on the acid pretreatment and GOx reaction times. The steady-state response of the optimized biosensor exhibits a sensitivity of 20.6 μA mM⁻¹ cm⁻², a linear range of up to 8 mM, and a response time of <5 s.     

Electrocatalytic activity of 2,3,5,6-tetrachloro-1,4-benzoquinone/multi-walled carbon nanotubes immobilized on edge plane pyrolytic graphite electrode for NADH oxidation

This work reports the electrocatalytic activity of 2,3,5,6-tetrachloro-1,4-benzoquinone (TCBQ)/multi-walled carbon nanotubes (MWCNT) immobilized on an edge plane pyrolytic graphite electrode for nicotinamide adenine dinucleotide (NADH) oxidation. Scanning electron microscopy (SEM) and energy dispersive X-ray spectrometry (EDS) were used to confirms the presence of chloro after the nanotube modification with 2,3,5,6-tetrachloro-1,4-benzoquinone. The surface charge transfer constant, k_s, and the charge transfer coefficient for the modified electrode, α, were estimated as 98.5 (±0.6) s⁻¹ and 0.5, respectively. With this modified electrode the oxidation potential of the NADH was shifted about 300 mV toward a less positive value, presenting a peak current much higher than those measured on an unmodified edge plane pyrolytic graphite electrode (EPPG). Cyclic voltammetry and rotating disk electrode (RDE) experiments indicated that the NADH oxidation reaction involves 2 electrons and a heterogenous rate constant (k_obs) of 3.1 × 10⁵ mol⁻¹ l s⁻¹. The detection limit, repeatability, long-term stability, time of response and linear response range were also investigated.     

Tetracarboxylic acid cobalt phthalocyanine SAM on gold: Potential applications as amperometric sensor for H2O2 and fabrication of glucose biosensor

This report describes the applications of cobalt tetracarboxylic acid phthalocyanine (CoTCAPc) self-assembled monolayer (SAM) immobilized onto a preformed 2-mercaptoethanol (Au-ME) SAM on gold surface (Au-ME-CoTCAPc SAM) as a potential amperometric sensor for the detection of hydrogen peroxide (H₂O₂) at neutral pH conditions. The Au-ME-CoTCAPc SAM sensor showed a very fast amperometric response time of approximately 1 s, good linearity at the studied concentration range of up to 5 μM with a coefficient R² = 0.993 and a detection limit of 0.4 μM oxidatively. Also reductively, the sensor exhibited a very fast amperometric response time (∼1 s), linearity up to 5 μM with a coefficient R² = 0.986 and a detection limit of 0.2 μM. The cobalt tetracarboxylic acid phthalocyanine self-assembled monolayer was then evaluated as a mediator for glucose oxidase (GOx)-based biosensor. The GOx (enzyme) was immobilized covalently onto Au-ME-CoTCAPc SAM using coupling agents: N-ethyl-N(3-dimethylaminopropyl) carbodiimide (EDC) and N-hydroxy succinimide (NHS), and the results demonstrated a good catalytic behavior. Kinetic parameters associated with the enzymatic and mediator reactions were estimated using electrochemical versions of Lineweaver-Burk and Hanes equation, and the stability of the sensor was tested. The biosensor (Au-ME-CoTCAPc-GOx SAM) electrode showed good sensitivity (7.5 nA/mM) with a good detection limit of 8.4 μM at 3σ, smaller Michaelis-Menten constant (4.8 mM from Hanes plot) and very fast response time of approximately 5 s.