Long-term monitoring of atmospheric corrosion at weathering steel bridges by an electrochemical impedance method

Weathering steel corrosion was monitored for one to two years under natural atmosphere by an electrochemical impedance technique. Two identical comb-shape weathering steel sheets embedded in epoxy resin were used as monitoring probe electrodes at two different bridges in Japan. Impedances at 10 kHz (Z_10kHz) and 10 mHz (Z_10mHz) were automatically measured every hour. Coupons (50 × 50 × 2 mm³) prepared from the same steel sheets were exposed together to measure the corrosion mass loss. The average (Z_10mHz)⁻¹ value for half to one year exposure correlated well with the average corrosion rate determined from the corrosion mass loss.     

A method for investigation of hot corrosion by gaseous Na2SO4

A novel in situ exposure method for investigating hot corrosion of aluminde coatings in the absence of an alkali sulphate melt is presented. The samples are exposed to Na₂SO₄(g) at a temperature above the dew point of the gas. Results from 100 and 500 h exposures at 900 °C of Ni-based In792 covered with SIF232 aluminide coating are presented. Already after 100 h of testing, attack characteristic for Type I hot corrosion is observed. The reactions taking place during the testing are discussed and the results are compared with those from the well-known ex situ salt hot corrosion test.     

Design and synthesis of a novel class of inhibitors for mild steel corrosion in acidic and carbon dioxide-saturated saline media

p-(9-(2-Methylisoxazolidin-5-yl)nonyloxy)benzaldehyde I, prepared using a cycloaddition protocol, was elaborated into its cinnamaldehyde derivative II which upon quarternization with propargyl chloride afforded III bearing an interesting blend of structural traits suitable for imparting inhibition of mild steel corrosion. Novel compounds I–III showed efficient inhibition against mild steel corrosion in CO₂–0.5 M NaCl (40 °C, 1 atm; 120 °C, 10 bar), 1, 4, 7.7 M HCl, and 0.5 M H₂SO₄ at 60 °C as determined by gravimetry and electrochemical methods. The presence of carbonaceous surface and nitrogen, as revealed by XPS study, indicated the formation of a film covering the metal surface, which imparted corrosion inhibition.     

Estimation of residual corrosion rates of steel under cathodic protection in soils via voltammetry

Steel coupons were buried in soil for 2 months under cathodic protection. Their residual corrosion rates were deduced from voltammetry and weight loss measurements. In aerated soils, the current density due to O₂ reduction, j_K,O2, was modelled with a mixed activation–diffusion controlled kinetic. The anodic part j_A of the current density j, computed as j_A = j − j_K,O2, obeyed Tafel law. Its extrapolation to the protection potential gave a corrosion rate (∼7 μm yr⁻¹) consistent with that obtained from weight loss measurements. With a deficient protection, corrosion rates remained at ∼80 μm yr⁻¹, a value given by both methods.     

Effect of Y2O3 content in the pack on microstructure and hot corrosion resistance of Y–Co-modified aluminide coating

Y–Co-modified aluminide coatings on nickel base superalloys were prepared by pack cementation method. Effect of Y₂O₃ content in the pack mixture on microstructure and hot corrosion resistance of the coatings was investigated. The results show that with the increase in Y₂O₃ content, the content of Co in the coatings increases. The mass gain of the coatings with Y₂O₃ addition of 1, 2 and 3 wt.% is 0.6, 0.55 and 0.42 mg/cm² after hot corrosion at 1173 K for 100 h, respectively. Y₂O₃ addition accelerates the diffusion of Co and thus increases the hot corrosion resistance of the coating.     

Inhibitive properties of 2,5-bis(n-methylphenyl)-1,3,4-oxadiazole and biocide on corrosion,biocorrosion and scaling controls of brass in simulated cooling water

2,5-Bis(n-methylphenyl)-1,3,4-oxadiazole with (n = 2,3,4), denoted n-MPOX, have been investigated by using potentiodynamic polarization (PP) and electrochemical impedance spectroscopy (EIS) methods, to evaluate the electrochemical behavior of brass in simulated cooling water system. The PP study revealed that oxadiazole inhibited both cathodic and anodic reactions, indicating a mixed type control of inhibition. It was shown that, 3-MPOX as well as 4-MPOX, were the best inhibitors and the inhibition efficiency followed the sequence: 3-MPOX ⩾ 4-MPOX ≫ 2-MPOX. The interference between non-oxidizing biocide CTAB and 3-MPOX and 4-MPOX against corrosion and biocorrosion has also been studied.     

Mechanistic studies of corrosion product flaking on copper and copper-based alloys in marine environments

The mechanism of corrosion product flaking on bare copper sheet and three copper-based alloys in chloride rich environments has been explored through field and laboratory exposures. The tendency for flaking is much more pronounced on Cu and Cu–4 wt%Sn than on Cu–15 wt%Zn and Cu–5 wt%Al–5 wt%Zn. This difference is explained by the initial formation of zinc and zinc–aluminum hydroxycarbonates on Cu15Zn and Cu5Al5Zn, which delays the formation of CuCl, a precursor of Cu₂(OH)₃Cl. As a result, the observed volume expansion during transformation of CuCl to Cu₂(OH)₃Cl, and concomitant corrosion product flaking, is less severe on Cu15Zn and Cu5Al5Zn than on Cu and Cu4Sn.     

Corrosion inhibition by anionic surfactants of AA2198 Li-containing aluminium alloy in chloride solutions

This paper evaluates the inhibiting action of some anionic surfactants towards AA2198 corrosion in NaCl solutions; the effect of surfactant concentration in relation to chloride amount was determined.On separate electrodes, polarization curves were recorded after 1, 24 and 168 h immersion in the aggressive media, while EIS technique continuously monitored the alloy corrosion process.In general, these substances stifled both the cathodic and anodic processes and noticeably shifted the pitting potential (breakdown potential, E_BR) in the positive direction. The most efficient compounds were N-lauroylsarcosine sodium salt and sodium dodecyl-benzenesulfonate, able to withstand the effects of 0.1 M Cl⁻.     

Sulphuric acid corrosion of ultrafine-grained mild steel processed by equal-channel angular pressing

A bulk ultrafine-grained (UFG) mild steel with a ferrite grain size of approximately 200 nm and a dispersed distribution of iron carbide particles was fabricated by equal-channel angular pressing (ECAP) at 400 °C. The corrosion behaviour of the ECAP-processed mild steel and pure iron was investigated in a 0.5 mol/L H₂SO₄ solution. They exhibited a higher corrosion rate and better anodic passivity properties due to the presence of more crystalline defects. As a result of the refinement of the iron carbide particles, the forming ability of a continuous dense passive film was improved.     

A study on the initial corrosion behavior of carbon steel exposed to outdoor wet-dry cyclic condition

The initial corrosion behavior of carbon steel subjected to outdoor wet-dry cyclic exposure and exposure under natural environments have been investigated. The weight loss results indicate a transition from corrosion acceleration to deceleration during the early stage of corrosion of carbon steel under both conditions. The corrosion kinetics under both conditions follow empirical equation D = Atⁿ. Outdoor wet-dry cyclic exposure significantly promoted the initiation but the rate of corrosion was about three times as fast. The morphology of corrosion surfaces and cross-section of rust layer have been examined using SEM and the compositions have been analyzed using XRD and EPMA.     

Oxidation of Fe–10Cr in O2 and in O2 + H2O environment at 600 °C: A microstructural investigation

Oxidation of Fe–10Cr in dry and wet O₂ was studied at 600 °C for up to 168 h. Oxide microstructure was investigated by STEM/EDX, FIB/SEM and TEM. Oxidation in dry O₂ gives a Cr-rich protective (Fe_1−xCr_x)₂O₃ scale. The same protective oxide initially forms in O₂ + H₂O environment, but after an incubation period scale breakdown is triggered by CrO₂(OH)₂ evaporation that depletes the substrate in Cr and converts (Fe_1−xCr_x)₂O₃ to FeCr spinel oxide. Internal oxidation occurs after breakaway. Alternating external and internal oxidation result in the inward-growing scale showing a characteristic banded morphology.     

Corrosion of ultra-high-purity Mg in 3.5% NaCl solution saturated with Mg(OH)2

Corrosion was evaluated for ultra-high-purity magnesium (Mg) immersed in 3.5% NaCl solution saturated with Mg(OH)₂. The intrinsic corrosion rate measured with weight loss, P_W = 0.25 ± 0.07 mm y⁻¹, was slightly smaller than that for high-purity Mg. Some specimens had somewhat higher corrosion rates attributed to localised corrosion. The average corrosion rate measured from hydrogen evolution, P_AH, was lower than that measured with weight loss, P_W, attributed to dissolution of some hydrogen in the Mg specimen. The amount of dissolution under electrochemical control was a small amount of the total dissolution. A new hydride dissolution mechanism is suggested.     

Preparation,microstructure characterisation and corrosion behaviour of directionally grown TaSi2 fibre arrays with sharp tip fabricated by selective wet etching

Directionally solidified Si–TaSi₂ eutectic composite is selectively etched to fabricate well aligned TaSi₂ tip array for field emission application. The effect of etching parameters on TaSi₂ tip structure, and its corrosion behaviour in HNO₃/HF solution are investigated. At the optimised condition (HNO₃/HF = 5 for 50 min), sharp TaSi₂ tips with curvature radius of 18 nm and homogenous distribution are obtained, which greatly improves the figure of merit associated with field emission current. The TaSi₂ fibre presents smaller dissolution rate in the HNO₃/HF solution than Si matrix. The formation mechanism of etching pit on the Si matrix surface is also discussed.     

Corrosion behavior of an alumina forming austenitic steel exposed to supercritical carbon dioxide

Microstructure characterization of corrosion behavior of an alumina forming austenitic (AFA) steel exposed to supercritical carbon dioxide was conducted at 450–650 °C and 20 MPa. At low temperature and short exposure times, the oxidation kinetics were parabolic and the oxide scales were mainly composed of protective and continuous Al₂O₃ and (Cr, Mn)-rich oxide layers. As the temperature and exposure time increased, the AFA steel gradually suffered breakaway oxidation and its oxide scales showed a multilayer structure mainly composed of Fe₃O₄, (Cr, Fe)₃O₄, NiFe/FeCr₂O₄/Cr₂O₃/Al₂O₃, FeCr₂O₄/Al₂O₃, and NiFe/Cr₂O₃/Al₂O₃, in sequence. The corrosion mechanism based on the microstructure evolution is discussed in detail.     

Oxidation properties of self-propagating high temperature synthesized niobium disilicide

NbSi₂ monoliths were prepared by self-propagating high temperature synthesis (SHS) and hot pressing (HP) and their oxidation behavior was investigated at various temperatures (823–1123 K) in air. The combustion mode of SHS reaction was steady state combustion, and the combustion product was single-phase NbSi₂. Oxidation studies show that the highest mass gain was 0.95675 kg m⁻² at 1023 K. In cyclic oxidation, the oxidation rate was reduced and the mass gain was only 0.15507 kg m⁻². A dense protective amorphous SiO₂ scale formed at 823 K and 923 K whereas a porous multilayer SiO₂ and α/β-Nb₂O₅ oxide scales formed at and above 1023 K and spalled off. Pest oxidation of NbSi₂ monoliths was not observed in hot pressed NbSi₂ monoliths.     

Comparison of corrosion behaviour of zinc in NaCl and in NaOH solutions. Part I: Corrosion layer characterization

The corrosion layer formed on zinc sample in 0.6 M NaCl and 0.5 M NaOH solution under ambient conditions has been investigated. The corrosion layer morphology was analyzed using scanning electron microscopy (SEM). X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) were used to characterize the corrosion products of zinc. The thickness evolution of the corrosion layer was investigated by glow discharge optical emission spectroscopy (GDEOS). The corrosion layer formed in 0.5 M NaOH solution appeared more compact than that formed in 0.6 M NaCl solution. Zinc hydroxide chloride (Zn₅(OH)₈Cl₂·2H₂O) and zinc hydroxide carbonate (Zn₅(CO₃)₂(OH)₆) were formed on zinc surface in 0.6 M NaCl solution while in 0.5 M NaOH solution, zinc oxide (ZnO), zinc hydroxide (Zn(OH)₂) and zinc hydroxide carbonate (Zn₅(OH)₆(CO₃)₂·H₂O) were detected. Probable mechanisms of zinc corrosion products formation are presented.     

Long-term forecast of corrosion mass losses of technically important metals in various world regions using a power function

An analysis of the results of corrosion tests on flat and helix specimens made of technically important metals carried out within the ISO CORRAG program is given. Stochastic relationships between coefficient n in the power function, which characterizes the protective properties of the corrosion products, and the limiting corrosion rate α, with the corrosivity of each type of atmosphere were found. A forecast of corrosion losses for a period of up to 50 years was given using the linear function in the stationary stage, a power function, and limiting corrosion rate values α. The reliability of the forecasts was estimated.     

Adsorption and inhibition effect of Ascorbyl palmitate on corrosion of carbon steel in ethanol blended gasoline containing water as a contaminant

The adsorption and inhibition effect of Ascorbyl palmitate (AP) on carbon steel in ethanol blended gasoline containing water as a contaminant (GE10 + 1%water) was studied by weight loss and electrochemical impedance spectroscopic (EIS) techniques. The results showed that the addition of ethanol and water to gasoline increase the corrosion rate of carbon steel. AP inhibits the corrosion of carbon steel in (GE10 + 1% water) solution to a remarkable extent. The adsorption of AP on the carbon steel surface was found to obey the Langmuir adsorption isotherm model. The values of activation energy (E_a) and various thermodynamic parameters were calculated and discussed.     

Orientation dependence of the electrochemical corrosion properties of electrodeposited Cu foils

In this study, the electrochemical corrosion properties of electrodeposited Cu foils in a CuCl₂-containing acidic etching solution were investigated. The main passive product was CuCl and a trace amount of Cu₂O can also be detected. The (2 2 0)-oriented Cu foils exhibited higher corrosion potential and lower corrosion current density than those with (1 1 1) or (2 0 0) texture, suggesting a superior corrosion resistance against the etching solution. It is proposed that the preferred orientation and thus the differences in atomic stacking density on specific planes dominated the corrosion properties of the electrodeposited Cu foils instead of grain size or surface roughness.     

Effect of N and C on stress corrosion cracking susceptibility of austenitic Fe18Cr10Mn-based stainless steels

Stress corrosion cracking (SCC) susceptibility of austenitic Fe18Cr10Mn alloys with 0.3N, 0.6N and 0.3N0.3C was investigated in aqueous chloride environment using a slow strain rate test method. The SCC susceptibility of Fe18Cr10Mn alloys in 2 M NaCl solution at 50 °C under constant anodic potential condition decreased with increase in N content from 0.3 to 0.6 wt%, and with addition of 0.3 wt% C to the Fe18Cr10Mn0.3N alloys. The present study strongly suggested that the beneficial effects of N and C on the SCC behavior of Fe18Cr10Mn alloys would be associated with the resistance to pitting corrosion initiation and the repassivation kinetics.