Synthesis of n-type Bi2Te1-xSex compounds through oxide reduction process and related thermoelectric properties

We propose a new process for the fabrication of n-type Bi₂Te_3-xSe_x (x = 0, 0.25, 0.4, 0.7) compounds. The compounds could be synthesized successfully using only oxide powders as the starting materials via the mechanical milling, oxidation, reduction, and spark plasma sintering processes. The controllability of the Se content could be ascertained by structural, electrical, and thermal characterizations, and the highest thermoelectric figure of merit (ZT) of 0.84 was achieved in Bi₂Te_2.6Se_0.4 compound at 423 K without any intentional doping. This process provides a new route to fabricate n-type Bi₂Te_3-xSe_x compounds with competitive ZTs using all oxide starting materials.     

Preparation and thermoelectric properties of MoS2/Bi2Te3 nanocomposites

MoS₂ nanosheets with size of several-hundred nanometers were prepared by a hydrothermal intercalation/exfoliation method, then MoS₂/Bi₂Te₃ composite nanopowders were prepared by a microwave-assisted wet chemical method using the MoS₂ nanosheets, TeO₂, Bi(NO₃)₃·5H₂O, KOH and ethylene glycol as raw materials. Bulk MoS₂/Bi₂Te₃ nanocomposites were prepared by hot pressing the MoS₂/Bi₂Te₃ composite nanopowders with MoS₂ nanosheet content ranging from 0 to 17 wt% at 80 MPa and 648 K in vacuum. X-ray photoelectron spectroscopy and X-ray diffraction analyses indicate that MoS₂ and Bi₂Te₃ did not react each other during the hot pressing. FESEM observation reveals that the MoS₂/Bi₂Te₃ composite samples had a more compact microstructure than the pristine Bi₂Te₃ bulk sample. The MoS₂ phase was relatively randomly dispersed in the composite. At a given temperature, the electrical conductivity of the composites increases first then decreases as the MoS₂ content increases, whereas the Seebeck coefficient of the bulk nanocomposites does not change much. A highest power factor, ~18.3 μW cm⁻¹ K⁻² which is about 30% higher than that of pristine Bi₂Te₃ sample, at 319 K has been achieved from a nanocomposite sample containing 6 wt% MoS₂.     

Thermal transport phenomena and limitations in heterogeneous polymer composites containing carbon nanotubes and inorganic nanoparticles

An Off-Lattice Monte Carlo model was developed to investigate effective thermal conductivities (K_eff) and thermal transport limitations of polymer composites containing carbon nanotubes (CNTs) and inorganic nanoparticles. The simulation results agree with experimental data for poly(ether ether ketone) (PEEK) with inclusions of CNTs and tungsten disulfide (WS₂) nanoparticles. The developed model can predict the thermal conductivities of multiphase composite systems more accurately than previous models by taking into account interfacial thermal resistance (R_bd) between the nanofillers and the polymer matrix, and the nanofiller orientation and morphology. The effects of (i) R_bd of CNT–PEEK and WS₂–PEEK (0.0232–115.8 × 10⁻⁸ m²K/W), (ii) CNT concentration (0.1–0.5 wt%), (iii) CNT morphology (aspect ratio of 50–450, and diameter of 2–8 nm), and (iv) CNT orientation (parallel, random and perpendicular to the heat flux) on K_eff of a multi-phase composite are quantified. The simulation results show that K_eff of multiphase composites increases when the CNT concentration increases, and when the R_bd of CNT–PEEK and WS₂–PEEK interfaces decrease. The thermal conductivity of composites with CNTs parallel to the heat flux can be enhanced ∼2.7 times relative to that of composites with randomly-dispersed CNTs. CNTs with larger aspect ratio and smaller diameter can significantly improve the thermal conductivity of a multiphase polymer composite.     

Enhanced thermoelectric properties of CNT dispersed and Na-doped Bi2Ba2Co2Oy composites

The thermoelectric properties of Bi₂Ba₂Co₂O_y and Bi_1.975Na_0.025Ba₂Co₂O_y+x wt% carbon nanotubes (CNT; x=0.00, 0.05, 0.10, 0.15, 0.5, and 1.0) ceramic samples synthesised by the solid-state reaction method were investigated from 300K to 950K. Na doping with a small amount played an important role in reducing resistivity and slightly reduced the Seebeck coefficients and the thermal conductivity. The CNT dispersant increased resistivity, but the thermal conductivity was reduced remarkably. In particular, the Bi_1.975Na_0.025Ba₂Co₂O_y+1.0wt% CNT sample exhibited an ultralow thermal conductivity of 0.39 W K⁻¹ m⁻¹ at 923K. This was attributed to the point defects caused by Na doping and the interface scattering caused by the CNT dispersant. The combination of Na doping and CNT dispersion had better effects on thermoelectric properties. The Bi_1.975Na_0.025Ba₂Co₂O_y+0.5wt% CNT sample exhibited a better dimensionless figure of merit (ZT) value of 0.2 at 923K, which was improved by 78.2%, compared with the undoped Bi₂Ba₂Co₂O_y sample.     

Effect of particle size,heating rate and CNT addition on densification,microstructure and mechanical properties of B4C ceramics

Monolithic B₄C ceramics and B₄C–CNT composites were prepared by spark plasma sintering (SPS). The influence of particle size, heating rate, and CNT addition on sintering behavior, microstructure and mechanical properties were studied. Two different B₄C powders were used to examine the effect of particle size. The effect of heating rate on monolithic B₄C was investigated by applying three different heating rates (75, 150 and 225 °C/min). Moreover, in order to evaluate the effect of CNT addition, B₄C–CNT (0.5–3 mass%) composites were also produced. Fully dense monolithic B₄C ceramics were obtained by using heating rate of 75 °C/min. Vickers hardness value increased with increasing CNT content, and B₄C–CNT composite with 3 mass% CNTs had the highest hardness value of 32.8 GPa. Addition of CNTs and increase in heating rate had a positive effect on the fracture toughness and the highest fracture toughness value, 5.9 MPa m^1/2, was achieved in composite with 3 mass% CNTs.     

Preparation and thermoelectric properties of Bi2SexTe3−x bulk materials

Bi₂Te₃ and Bi₂Se₃ nanoplates were synthesized by a microwave-assisted wet chemical method, and Bi₂Se_xTe_3−x (x=1, 2, 3) bulk nanocomposites were then prepared by hot pressing the Bi₂Te₃ and Bi₂Se₃ nanoplates at 80 MPa and 723 K in vacuum. The phase composition and microstructures of the bulk samples were characterized by powder X-ray diffraction and field-emission scanning electron microscopy, respectively. The electrical conductivity of the Bi₂Se_xTe_3−x bulk nanocomposites increases with increasing Se content, and the Seebeck coefficient value is negative, showing n-type conduction. The absolute Seebeck coefficient value decreases with increasing Se content. A highest power factor, 24.5 µWcm⁻¹ K⁻², is achieved from the sample of x=1 at 369 K among the studied samples.     

Improved mechanical performance of solution-processed MWCNT/Ag nanoparticle composite films with oxygen-pressure-controlled annealing

A method for the synthesis of solution process-based MWCNT/Ag nanoparticle composite thin films as electrode or interconnect materials for flexible electronic devices is presented. The method produces homogeneously-dispersed CNT networks and increases the density of the Ag matrix, which are major factors in determining the mechanical performance of CNT/Ag films. By introducing nanometer-sized Ag particles as a matrix material, the agglomeration of CNTs is suppressed. In addition, the generation of pores during the synthesis procedure is effectively restrained by oxygen-pressure-controlled annealing. The elastic modulus of the pristine Ag films was observed to increase by 34% by adding 5 wt% CNTs. An improvement in the fatigue resistance of the CNTs under cyclic tensile deformation was confirmed. The normalized resistance change ((R ? R_o)/R_o) of the Ag films containing 5 wt% CNTs after fatigue testing was reduced by about 27% compared to that of the pristine Ag films. For industrial application the process has the advantage of relatively low-temperature processing without any high pressure compaction compared to the conventional powder metallurgy techniques normally used.     

Pressureless sintering of carbon nanotube–Al2O3 composites

Alumina ceramics reinforced with 1, 3, or 5 vol.% multi-walled carbon nanotubes (CNTs) were densified by pressureless sintering. Commercial CNTs were purified by acid treatment and then dispersed in water at pH 12. The dispersed CNTs were mixed with Al₂O₃ powder, which was also dispersed in water at pH 12. The mixture was freeze dried to prevent segregation by differential sedimentation during solvent evaporation. Cylindrical pellets were formed by uniaxial pressing and then densified by heating in flowing argon. The resulting pellets had relative densities as high as ～99% after sintering at 1500 °C for 2 h. Higher temperatures or longer times resulted in lower densities and weight loss due to degradation of the CNTs by reaction with the Al₂O₃. A CNT/Al₂O₃ composite containing 1 vol.% CNT had a higher flexure strength (～540 MPa) than pure Al₂O₃ densified under similar conditions (～400 MPa). Improved fracture toughness of CNT–Al₂O₃ composites was attributed to CNT pullout. This study has shown, for the first time, that CNT/Al₂O₃ composites can be densified by pressureless sintering without damage to the CNTs.     

Boehmite derived surface functionalized carbon nanotube-reinforced macroporous alumina ceramics

Carbon nanotube (CNT)-reinforced macroporous alumina ceramics with tailored porosity were fabricated using hydrothermally synthesized (200 °C for 2 h) boehmite–CNT starting composite powders. Multi-wall CNTs were first mixed with a mixture of chemicals suitable to synthesize stoichiometric boehmite powders and then put in an autoclave. During hydrothermal synthesis, the formation of fine particles of boehmite was accompanied by the functionalization of CNTs. Subsequently, CNT–boehmite powders were used to produce bulk ceramics and sintering took place in a vacuum furnace at 1450 °C for 3 h for the formation of CNT-reinforced alumina ceramics. The pore network in various dimensions occurred as a consequence of the reconstructive transformation and dehydration of boehmite during the transformation to alumina. FEG-SEM and TEM analysis were used to determine the CNT distribution in the matrix, the morphology and size of particles, as well as the visual properties of the pores. The final macroporous alumina ceramics can be considered to be ideal for the separation and filtration of contaminants in liquid or air environment.     

Bismuth titanates candidates for high permittivity LTCC

Bi₂O₃–TiO₂ composites are known to possess attractive microwave dielectric properties. However, producing LTCC analogues with equally promising dielectric properties is problematic. Here, we show that judicious choice of both TiO₂ starting powders and dopants can produce composites with excellent properties. Three TiO₂ powders were evaluated: 1 μm-anatase, 1 μm-rutile and a nanosized (30 nm) mixture of 75–25 anatase-rutile. The best dielectric properties were obtained by using uncalcined nanosized anatase/rutile with Bi₂O₃ powder. By doping this Bi₂O₃–TiO₂ powder mixture with 0.112 wt.% CuO dielectric properties of Q × f = 9000 GHz, ɛ_r = 80 and τ_f = 0 ppm/K (at 300 K) were obtained at a sintering temperature of 915 °C.     

Preparation-microstructure-property relationships in double-walled carbon nanotubes/alumina composites

Double-walled carbon nanotube/alumina composite powders with low carbon contents (2–3 wt.%) are prepared using three different methods and densified by spark plasma sintering. The mechanical properties and electrical conductivity are investigated and correlated with the microstructure of the dense materials. Samples prepared by in situ synthesis of carbon nanotubes (CNTs) in impregnated submicronic alumina are highly homogeneous and present the higher electrical conductivity (2.2–3.5 S cm⁻¹) but carbon films at grain boundaries induce a poor cohesion of the materials. Composites prepared by mixing using moderate sonication of as-prepared double-walled CNTs and lyophilisation, with little damage to the CNTs, have a fracture strength higher (+30%) and a fracture toughness similar (5.6 vs 5.4   MPa m^1/2) to alumina with a similar submicronic grain size. This is correlated with crack-bridging by CNTs on a large scale, despite a lack of homogeneity of the CNT distribution.     

Optical,thermal and dielectric properties of Bi4(TiO4)3 ceramic powders

Bismuth titanate (Bi₄(TiO₄)₃) ceramic powders have been synthesized by using a solid state reaction method. Prominently intense blue emission at 480 nm has been measured with an excitation at 418 nm. The reason for the observance of such a blue emission from this ceramic powder has been explained. The phase formation has been investigated by X-ray diffraction analysis (XRD). The morphology and composition of the ceramic powders have been studied from the measurement of SEM and EDS profiles. FTIR and Raman spectra have also been recorded to analyze the presence of functional groups and Raman active modes in the Bi₄(TiO₄)₃ ceramic powders. The sintering temperature has been optimized to be 1100 °C based on the measured TG–DTA profiles of the as prepared material. Besides these, dielectric properties of ceramic powder in the frequency range of 200 Hz–3 MHz at 300 K have also been carried out.     

Enhanced transport critical current density of (Bi,Pb)-2223/Ag superconductor tapes added with nano-sized Bi2O3

Ag sheathed superconductor tapes with starting composition (Bi, Pb)-2223(Bi₂O₃)_0.01 were prepared. Bi₂O₃ with average size 150 nm was used in this work. The Bi₂O₃ amount was chosen based on our initial study on nano-sized Bi₂O₃ added pellets which showed an optimal superconducting property for 0.01 wt% addition. Non-added tapes were also prepared for comparison. The tapes were investigated by X-ray diffraction method, scanning electron microscopy and transport critical current density, J_c measurements (30 K to 77 K). The influence of different sintering times (50, 100, and 150 h) on J_c under applied magnetic field (0–0.75 T at 77 K) parallel and perpendicular to the surface of the tapes was also investigated. J_c of added tapes was found to increase significantly as compared with the non-added tapes. The Bi₂O₃ added tapes sintered for 150 h exhibited the highest J_c at 30 K of 57,900 A/cm² as compared with 19,400 A/cm² for the non-added tapes sintered for 100 h. The improvements in flux pinning and connectivity between grains due to nano Bi₂O₃ addition led to the enhancement of J_c.     

Electromagnetic interference shielding properties of polymer-grafted carbon nanotube composites with high electrical resistance

Poly(methyl methacrylate) (PMMA)-grafted multiwalled CNTs were prepared, and then dispersed into additional PMMA matrix, yielding highly insulated PMMA–CNT composites. The volume resistivity of PMMA–CNT was as high as 1.3 × 10¹⁵ Ω cm even at 7.3 wt% of the CNT. The individual CNTs electrically-isolated by the grafted PMMA chains in PMMA–CNT transmitted electromagnetic (EM) waves in the frequency range of 0.001–1 GHz, whereas the percolated CNTs in a conventional composite prepared by blending PMMA with the pristine CNTs strongly shielded the EM waves. This result suggests that the intrinsic conductivity of the CNT itself in PMMA–CNT does not contribute to the EM interference (EMI) shielding in the frequency range of 0.001–1 GHz. On the other hand, PMMA–CNT exhibited EMI shielding at the higher frequency range than 1 GHz because the dielectric loss of the CNT itself was rapidly increased over 1 GHz. At 110 GHz, PMMA–CNT with 7.3 wt% of the CNT had EMI SE of as high as 29 dB (0.57 mm thickness), though is slightly lower than that of the percolated conventional composite (35 dB). Thus, it is demonstrated that the highly insulated PMMA–CNT has the good EMI shielding at extremely high frequency range (30–300 GHz).     

Thermal conductivity of MWCNT/epoxy composites: The effects of length,alignment and functionalization

Carbon nanotubes (CNTs) show great promise to improve composite electrical and thermal conductivity due to their exceptional high intrinsic conductance performance. In this research, long multi-walled carbon nanotubes (long-MWCNTs) and its thin sheet of entangled nanotubes were used to make composites to achieve higher electrical and thermal conductivity. Compared to short-MWCNT sheet/epoxy composites, at room temperature, long-MWCNT samples showed improved thermal conductivity up to 55 W/mK. The temperature dependence of thermal conductivity was in agreement with κ ∝ Tⁿ (n = 1.9–2.3) below 150 K and saturated around room temperature due to Umklapp scattering. Samples with the improved CNT degree of alignment by mechanically stretching can enhance the room temperature thermal conductivity to over 100 W/mK. However, functionalization of CNTs to improve the interfacial bonding resulted in damaging the CNT walls and decreasing the electrical and thermal conductivity of the composites.     

Preparation and characterization of manganese oxide/CNT composites as supercapacitive materials

Manganese oxide was synthesized and dispersed on carbon nanotube (CNT) matrix by thermally decomposing manganese nitrates. CNTs used in this paper were grown directly on graphite disk by chemical vapor deposition technique. The capacitive behavior of manganese oxide/CNT composites was investigated by cyclic voltammetry and galvanostatic charge–discharge method in 1 M Na₂SO₄ aqueous solutions. When the loading mass of MnO₂ is 36.9 μg cm^− 2, the specific capacitance of manganese oxide/CNT composite (based on MnO₂) at the charge–discharge current density of 1 mA cm^− 2 equals 568 F g^− 1. Additionally, excellent charge–discharge cycle stability (ca. 88% value of specific capacitance remained after 2500 charge–discharge cycles) and power characteristics of the manganese oxide/CNT composite electrode can be observed. The effect of loading mass of MnO₂ on specific capacitance of the electrode has also been investigated.     

Synthesis and microwave dielectric properties of Bi2Ge3O9 ceramics for application as advanced ceramic substrate

During the synthesis of Bi₂Ge₃O₉ ceramics using Bi₂O₃ + 3GeO₂ powders, the Bi₄Ge₃O₁₂ phase was formed at low temperature (≤800 °C). Bi₄Ge₃O₁₂ preferentially adopted GeO₂-excess phase, and this phase was consistently present in the sintered Bi₂Ge₃O₉ ceramic as a secondary phase. Therefore, Bi₄Ge₃O₁₂ powder was first calcined and subsequently reacted with GeO₂ powder to obtain the pure Bi₂Ge₃O₉ ceramic through the following reaction: 1/2Bi₄Ge₃O₁₂ + 3/2GeO₂ → Bi₂Ge₃O₉. Formation of the Bi₂Ge₃O₉ phase was initiated at temperature of 850 °C. The pure Bi₂Ge₃O₉ ceramic sintered at 875 °C for 8 h had a dense microstructure with an average grain size of 2.7 μm. Furthermore, the pure Bi₂Ge₃O₉ ceramic exhibited promising microwave dielectric properties for the advanced ceramic substrate: ε_r = 9.7, Q × f = 48,573 GHz and τ_f = −29.5 ppm/°C.     

Densification during hot-pressing of carbon nanotube–metal–magnesium aluminate spinel nanocomposites

The densification by hot-pressing of ceramic–matrix composites containing a dispersion of carbon nanotubes (CNT), mostly single-walled, is studied for the first time. Fifteen different CNT–Co/Mo–MgAl₂O₄ composite powders containing between 1.2 and 16.7 vol.% CNT were prepared by catalytic chemical vapour deposition. The in situ growth of CNT within the oxide powder made it possible to obtain a highly homogeneous distribution of CNT. Low contents of CNT (up to 5 vol.%) are beneficial for the first shrinkage step (up to 1100 °C), dominated by the rearrangement process, while higher contents are detrimental. At higher temperatures (1100–1300 °C), CNT clearly inhibit the shrinkage, and this detrimental effect regularly increases with the CNT content. Several explanations are proposed, in relation with the particular mechanical properties of CNT and their highly connected web-like distribution within the material.     

Synthesis,microstructure and electrical conductivity of carbon nanotube–alumina nanocomposites

Carbon nanotube–alumina (CNT–Al₂O₃) nanocomposites have been synthesized by direct growth of carbon nanotubes on alumina by chemical vapor deposition (CVD) and the as-grown nanocomposites were densified by spark plasma sintering (SPS). Surface morphology analysis shows that the CNTs and CNT bundles are very well distributed between the matrix grains creating a web of CNTs as a consequence of their in situ synthesis. Even after the SPS treatment, the CNTs in the composite material are still intact. Experimental result shows that the electrical conductivity of the composites increases with the CNT content and falls in the range of the conductivity of semiconductors. The nanocomposite with highest CNT content has electrical conductivity of 3336 S/m at near room temperature, which is about 13 orders of magnitude increase over that of pure alumina.     

Size-tailored synthesis of gold nanoparticles and their facile deposition on AAO-templated carbon nanotubes via electrostatic self-assembly: Application to H2O2 detection

The use of gold nanoparticle/carbon nanotube composite (AuNP/CNT) is of current interest in the development of nanomaterial based sensing and electronic devices. Herein, we demonstrate a novel method to tailor the size of positively charged AuNPs under the influence of two capping agents, polyvinylpyrrolidone (PVP) and 4-dimethylaminopyridine (DMAP). By varying the mole ratios of PVP:DMAP (P:D) from 1:32 to 32:1, the average diameters of AuNPs were progressively decreased from 17.3 nm to 1.8 nm. Therefore, PVP played a dominant role in the formation of small AuNPs. Moreover, these size-controlled AuNPs could be electrostatically deposited onto the anodic aluminum oxide (AAO)-templated CNTs without requiring a pretreatment of the CNT surfaces. The obtained AuNPs/CNTs with different Au core sizes were also compared in terms of electroactivity towards hydrogen peroxide (H₂O₂) reduction. The greatest voltammetric response was of Au-(P1:D4-10.6 nm)/CNTs caused by their reduced charge transfer resistance from the low covering of PVP on the Au surfaces and by their dense and uniform AuNPs. This modified electrode also provided a wide linearity range for H₂O₂ detection from 5 μM to 45.80 mM with the low detection limit of 0.23 μM (S/N = 3). This study thus suggests the rational design of AuNP/CNT structure for an H₂O₂ sensor.