η-Al2O3与γ-Al2O3在CS2催化水解反应中的性能比较

通过制备高纯度的前驱体湃铝石获得了η-Al₂O₃材料,采用XRD验证了η-Al₂O₃与γ-Al₂O₃在晶相结构上的差异,比较了两者的表面形貌、织构及酸碱性能,结果显示,η-Al₂O₃与γ-Al₂O₃的比表面积相当,但η-Al₂O₃具有更弱的弱碱位和较少的强碱位,并拥有丰富的中等强度酸性位。将η-Al₂O₃与γ-Al₂O₃作为催化剂应用于CS₂水解反应,结果表明,在(200~450) ℃测试温度范围内,η-Al₂O₃催化剂对CS₂的水解活性始终优于γ-Al₂O₃,两种催化剂上CS₂反应的浓度效应也明显不同,推测与它们的酸碱性质影响了对CS₂的吸附能力有关,导致两者催化CS₂水解反应遵循了不同的机制。     

Pt/Pt-Ce/γ-Al2O3催化氧化甲苯研究

通过等体积浸渍法制备单贵金属Pt/γ-Al₂O₃和双金属Pt-Ce/γ-Al₂O₃催化剂,考察Ce对催化剂活性的影响,确定催化剂最优配比。结果表明,当Pt的负载量为质量分数0.5%时,Pt/γ-Al₂O₃催化活性最高;当Pt的负载量为质量分数0.2%,Ce的负载量为质量分数1.0%时,Pt-Ce/γ-Al₂O₃催化剂的催化活性最高。Pt-Ce/γ-Al₂O₃催化剂的甲苯转化率高于Pt/γ-Al₂O₃催化剂。随着Pt负载量增大,催化剂孔容、孔径减小。粉体式催化剂性能优于整体式催化剂,但差别不大;Ce的添加有助于催化剂活性的提升。     

制备条件对NiMo/γ-Al2O3催化剂上萘加氢生成四氢萘的影响

采用等体积浸渍法制备加氢催化剂NiMo/γ-Al₂O₃,在悬浮床上考察不同的制备条件下NiMo/γ-Al₂O₃对萘加氢生成四氢萘的影响。结果表明,催化剂的制备条件对加氢活性有显著的影响,NiMo/γ-Al₂O₃催化剂的最佳制备条件为共浸渍法负载金属组分Ni和Mo,在500 ℃的温度下焙烧4 h。此条件下制备的催化剂上四氢萘的选择性高达95.2%。     

低成本大比表面积γ-Al2O3的制备

以廉价无机铝盐硫酸铝为原料,氨水为沉淀剂,十二烷基硫酸钠为添加剂,采用简单沉淀法制备得到较大比表面积γ-Al₂O₃。通过N₂低温物理吸附-脱附、X射线衍射、红外光谱、热重、元素分析、扫描及透射电镜等,研究制备过程中沉淀温度、溶液pH值和添加剂用量对产物γ-Al₂O₃及其前驱体的晶相结构、形貌织构等性质的影响。结果表明,在沉淀温度75 ℃、硫酸铝浓度0.25 mol·L^-1、溶液pH=9.0、老化时间12 h和n(十二烷基硫酸钠)∶n[Al₂(SO₄)₃]=0.375∶1条件下,所得前驱体(拟薄水铝石)经600 ℃焙烧后,可获得大比表面积(416.65 m²·g^-1)γ-Al₂O₃,并且样品中因十二烷基硫酸钠添加,引入的S及Na等杂质含量极少。     

K2CO3/γ-A12O3催化剂在棉籽油制备生物柴油中的应用

利用等体积浸渍法制备K₂CO₃/γ-A1₂O₃负载型固体碱催化剂,应用于棉籽油和甲醇酯交换反应制备生物柴油。对催化剂使用前的保存条件、水分、重复使用性能、游离脂肪酸影响以及失活和再生进行了分析。结果表明,固体催化剂K₂CO₃/γ-Al₂O₃具有较好的抗水性,酸度对催化剂影响明显,重复使用4次未经活化的催化剂,催化活性明显降低,催化剂应密封保存。K₂CO₃/γ-A1₂O₃负载型固体碱催化剂经济实惠且催化效果良好。     

柠檬醛在La2O3/γ-Al2O3催化剂上的等温吸附

对柠檬醛-乙酸乙酯溶液中柠檬醛在La₂O₃/γ-Al₂O₃催化剂上等温吸附行为进行了研究。结果表明,30 ℃柠檬醛在La₂O₃/γ-Al₂O₃催化剂上的吸附动力学符合准二阶吸附动力学模型,吸附动力学方程为：1/q_t=2.350/t+0.063 3(R²=0.998 5)。（30~65） ℃柠檬醛在La₂O₃/γ-Al₂O₃催化剂上的等温吸附符合Langmuir方程,温度升高使柠檬醛的饱和吸附量增加,吸附热为32.19 kJ·mol^-1。     

Pd-Ag/α-Al2O3催化剂在乙烷裂解配套制乙烯工艺中的选择加氢性能研究

在乙烷裂解配套制乙烯选择加氢的工艺条件下,考察载体焙烧温度、助剂Ag含量、溶液pH值、CO含量及空速对等体积浸渍法制备的Pd-Ag/α-Al₂O₃催化剂性能的影响。结果表明,载体焙烧温度的增加,有助于提高催化剂活性;催化剂Ag含量增加,反应温度变化不大,选择性及抗结焦性能增加;不同溶液pH制备催化剂,选择加氢性能差异不大,但溶液的酸性过高会降低催化剂的抗结焦性能;随着CO的升高,乙炔转化率降低,乙烯选择性先增高后降低,为保证催化剂选择性,原料中的CO最好保持在(700~1 600) μL·L^-1;随着空速的升高,乙炔转化率降低,乙烯选择性增加。     

CO气相偶联合成草酸二甲酯Pd/α-Al2O3催化剂失活与再利用

作为合成气制乙二醇关键步骤之一,CO与亚硝酸甲酯合成草酸二甲酯备受关注。综述了近年来CO气相偶联合成草酸二甲酯Pd/α-Al₂O₃催化剂失活与再利用研究进展,探讨催化剂再利用工艺存在的问题,指出应根据在工业应用中出现的问题对Pd/α-Al₂O₃催化剂进行失活研究,在此基础上开发针对性的再生工艺;钯催化剂回收方面萃取法和吸附法逐渐成为研究重点,高效、低耗、短流程绿色工艺的开发是失活钯催化剂再利用的发展方向。     

CeO2改性Ni/γ-Al2O3催化剂上顺酐加氢制备丁二酸酐

采用等体积浸渍法制备CeO₂改性Ni/γ-Al₂O₃催化剂,通过BET、XRD、H₂-TPR和SEM等对催化剂结构及物化性能进行表征,考察Ni-CeO₂/γ-Al₂O₃催化剂对顺酐催化加氢制备丁二酸酐催化性能的影响。结果表明,引入适量CeO₂可提高催化剂活性组分Ni的分散度,增加催化剂比表面积,提高催化剂热稳定性。采用负载CeO₂质量分数5%的Ni-CeO₂/γ-Al₂O₃催化剂,在反应温度120 ℃、反应压力2.0 MPa和空速0.6 h^-1条件下,顺酐转化率为99.5%,丁二酸酐选择性为99.4%。     

Sn掺杂对Pt/Sn(x)-θ-Al2O3丙烷脱氢催化剂性能的影响

采用铝箔盐酸回流-油柱成型法制备了不同Sn掺杂量的Sn(x)-θ-Al₂O₃载体,并采用真空浸渍法制备了Pt/Sn(x)-θ-Al₂O₃催化剂。对制备的催化剂进行XRD、N₂物理吸附-脱附、NH₃-TPD、H₂-TPR和TG-DTA表征,研究了在载体中掺入助剂Sn对Pt/Sn(x)-θ-Al₂O₃催化剂结构及丙烷脱氢催化反应性能的影响。结果表明,在载体制备过程中掺入Sn,可以提高催化剂反应活性和产物选择性,当Sn掺杂质量分数为1.0%时,催化剂具有最优的丙烷脱氢反应性能,15 h的平均丙烷转化率为32.4%,平均丙烯选择性为95.5%。     

The simultaneous activation of methane and carbon dioxide to C2 hydrocarbons under pulse corona plasma over La2O3/γ-Al2O3 catalyst

The pulse corona plasma has been used as an activation method for reaction of methane and carbon dioxide, the product was C₂ hydrocarbons and by-products were CO and H₂. Methane conversion and the yield of C₂ hydrocarbons were affected by the carbon dioxide concentration in the feed. The conversion of methane increased with increasing carbon dioxide concentration in the feed whereas the yield of C₂ hydrocarbons decreased. The synergism of La₂O₃/γ-Al₂O₃ and plasma gave methane conversion of 24.9% and C₂ hydrocarbons yield of 18.1% were obtained at the power input of plasma was 30 W. The distribution of C₂ hydrocarbons changed by using Pd-La₂O₃/γ-Al₂O₃ catalyst, the major C₂ product was ethylene.     

Performance and characterization of Ru/Al2O3 and Ru/SiO2 catalysts modified with Mn for Fischer–Tropsch synthesis

Mn effect and characterization on γ-Al₂O₃-, -Al₂O₃- and SiO₂-supported Ru catalysts were investigated for Fischer–Tropsch synthesis under pressurized conditions. In the slurry phase Fischer–Tropsch reaction, γ-Al₂O₃ catalysts showed higher performance on CO conversion and C₅⁺ selectivity than -Al₂O₃ and SiO₂ catalysts. Moreover, Ru/Mn/γ-Al₂O₃ exhibited high resistance to catalyst deactivation and other catalysts were deactivated during the reaction. From characterization results on XRD, TPR, TEM, XPS and pore distribution, Ru particles were clearly observed over the catalysts, and γ-Al₂O₃ catalysts showed a moderate pore and particle size such as 8 nm, where -Al₂O₃ and SiO₂ showed highly dispersed ruthenium particles. The addition of Mn to γ-Al₂O₃ enhanced the removal of chloride from RuCl₃, which can lead to the formation of metallic Ru with moderate particle size, which would be an active site for Fischer–Tropsch reaction. Concomitantly, manganese chloride is formed. These schemes can be assigned to the stable nature of Ru/Mn/γ-Al₂O₃ catalyst.     

Carbon formation and its influence on ethanol steam reforming over Ni/Al2O3 catalysts

Ethanol steam reforming was studied over Ni/Al₂O₃ catalysts. The effect of support (- and γ-Al₂O₃), metal loading and a comparison between conventional H₂ reduction with an activation method employing a CH₄/O₂ mixture was investigated. The properties of catalysts were studied by N₂ physisorption, X-ray diffraction (XRD) and temperature programmed reduction (TPR). After activity tests, the catalysts were analyzed by scanning electron microscopy (SEM) and thermogravimetric analysis (TG/DTA). Ni supported on γ-Al₂O₃ was more active for H₂ production than the catalyst supported on -Al₂O₃. Metal loading did not affect the catalytic performance. The alternative activation method with CH₄/O₂ mixture affected differently the activity and stability of the Ni/γ-Al₂O₃ and the Ni/-Al₂O₃ catalyst. This activation method increased significantly the stability of Ni/-Al₂O₃ compared to H₂ reduction. SEM and TG/DTA analysis indicate the formation of filamentous carbon during the CH₄/O₂ activation step, which is associated with the increasing catalyst activity and stability. The effect of temperature on the type of carbon formed was investigated; indicating that filamentous coke increased activity while encapsulating coke promoted deactivation. A discussion about carbon formation and the influence on the activity is presented.     

Study of Ag/La0.6Sr0.4MnO3 catalysts for complete oxidation of methanol and ethanol at low concentrations

Ag-modified La_0.6Sr_0.4MnO₃-based catalysts with the perovskite-type structure were prepared by using a citric acid sol–gel method, and their catalytic performance for complete oxidation of methanol and ethanol was evaluated and compared with that of the γ-Al₂O₃-supported catalysts, Ag/γ-Al₂O₃, Pt/γ-Al₂O₃, and Pd/γ-Al₂O₃. The results showed that the Ag-modified La_0.6Sr_0.4MnO₃-based catalysts with the perovskite-type structure displayed the activity significantly higher than that of the supported precious metal catalysts, 0.1%Pd/γ-Al₂O₃ and 0.1%Pt/γ-Al₂O₃ in the temperature range of 370–573 K. Over a 6%Ag/20%La_0.6Sr_0.4MnO₃/γ-Al₂O₃ catalyst, the T₉₅ temperature for methanol oxidation can be as low as 413 K. Even at such low reaction temperature, there were little HCHO and CO detected in the reaction exit-gas. However, for the 0.1%Pd/γ-Al₂O₃ and 0.1%Pt/γ-Al₂O₃ catalysts, the HCHO content in the reaction exit-gas reached 200 and 630 ppm at their T₉₅ temperatures. Over a 6%Ag/La_0.6Sr_0.4MnO₃ catalyst, the T₉₅ temperature for ethanol oxidation can be as low as 453 K, with a corresponding content of CH₃CHO in the exit-gas at 782 ppm; when ethanol oxidation is performed at 493 K, the content of acetaldehyde in the exit-gas can be below 1 ppm. Characterization of the catalysts by X-ray diffraction (XRD), TEM, XPS, laser Raman spectra (LRS), hydrogen temperature-programmed reduction (H₂-TPR) and oxygen temperature-programmed desorption (O₂-TPD) methods revealed that both the surface and the bulk phase of the perovskite La_0.6Sr_0.4MnO₃ played important roles in the catalytic oxidation of the alcohols, and that γ-Al₂O₃ as the bottom carrier could be beneficial in creating a large surface area of catalyst. Moreover, a small amount of Ag⁺ doped onto the surface of La_0.6Sr_0.4MnO₃ was able to partially occupy the positions of La³⁺ and Sr²⁺ due to their similar ionic radii, and thus, became stabilized by the perovskite lattice, which would be in favor of preventing the aggregation of the Ag species on the surface and enhancing the stability of the catalyst. On the other hand, modification of the Ag⁺ to the surface of La_0.6Sr_0.4MnO₃ resulted in an increase in relative content of the surface O₂²⁻/O⁻ species highly reactive toward the alcohols and aldehydes as well as CO. Besides, solution of low-valence metal oxides SrO and Ag₂O with proper amounts in the lattice of the trivalent metal perovskite-type oxide LaMnO₃ would also lead to an increase in the content of the reducible Mnⁿ⁺ and the formation of anionic vacancies, which would be favorable for the adsorption-activation of oxygen on the functioning catalyst and the transport of the lattice and surface oxygen species. All these factors would contribute to the pronounced improvement of the catalyst performance.     

Deactivation studies over NiO/γ-Al2O3 catalysts for partial oxidation of methane to syngas

Two types of NiO/γ-Al₂O₃ catalysts prepared by the impregnation and the sol–gel method were used for the partial oxidation of methane to syngas at 850°C (GHSV1.8×10⁵ lkg⁻¹ h⁻¹). The effects of the carbon deposition, the loss and sintering of nickel and the phase transformation of γ-Al₂O₃ support on the catalytic performance during 80 h POM reaction were investigated with a series of characterization such as XRD, BET, AAS, TG, and XPS. The results indicated that the carbon deposition and the loss and sintering of nickel could not cause the serious decrease of catalytic performance over NiO/γ-Al₂O₃ catalyst during the short-time reaction. However, the slow process of the support γ-Al₂O₃ phase transforming into -Al₂O₃ could slowly decrease the performance of NiO/γ-Al₂O₃ catalysts. Aimed at the reasons of the deactivation, an improved catalyst was obtained by the complexing agent-assisted sol–gel method.     

Surface properties and reactivity of Cu/γ-Al2O3 catalysts for NO reduction by C3H6: Influences of calcination temperatures and additives

The influences of calcination temperatures and additives for 10 wt.% Cu/γ-Al₂O₃ catalysts on the surface properties and reactivity for NO reduction by C₃H₆ in the presence of excess oxygen were investigated. The results of XRD and XPS show that the 10 wt.% Cu/γ-Al₂O₃ catalysts calcined below 973 K possess highly dispersed surface and bulk CuO phases. The 10 wt.% Cu/γ-Al₂O₃ and 10 wt.% Mn–10 wt.% Cu/γ-Al₂O₃ catalysts calcined at 1073 K possess a CuAl₂O₄ phase with a spinel-type structure. In addition, the 10 wt.% La–10 wt.% Cu/γ-Al₂O₃ catalyst calcined at 1073 K possesses a bulk CuO phase. The result of NO reduction by C₃H₆ shows that the CuAl₂O₄ is a more active phase than the highly dispersed and bulk CuO phase. However, the 10 wt.% Mn–10 wt.% Cu/γ-Al₂O₃ catalyst calcined at 1073 K possesses significantly lower reactivity for NO reduction than the 10 wt.% Cu/γ-Al₂O₃ catalyst calcined at 1073 K, although these catalysts possess the same CuAl₂O₄ phase. The low reactivity for NO reduction for 10 wt.% Mn–10 wt.% Cu/γ-Al₂O₃ catalyst calcined at 1073 K is attributed to the formation of less active CuAl₂O₄ phase with high aggregation and preferential promotion of C₃H₆ combustion to CO_x by MnO₂. The engine dynamometer test for NO reduction shows that the C₃H₆ is a more effective reducing agent for NO reduction than the C₂H₅OH. The maximum reactivity for NO reduction by C₃H₆ is reached when the NO/C₃H₆ ratio is one.