The positive effect of hydrogen on the reaction of nitric oxide with carbon monoxide over platinum and rhodium catalysts

The effect of adding 330–4930 ppm hydrogen to a reaction mixture of NO and CO (2000 ppm each) over platinum and rhodium catalysts has been investigated at temperatures around 200–250°C. Hydrogen causes large increases in the conversion of NO and, surprisingly, also of CO. Oxygen atoms from the additional NO converted are eventually combined with CO to give CO₂ rather than react with hydrogen to form water. This reaction is described by CO + NO +3/2H₂ CO₂ + NH₃ and accounts for 50–100% of the CO₂ formed with Pt/Al₂O₃ and 20–50% with Rh/Al₂O₃. With the latter catalyst a substantial amount of NO converted produces nitrous oxide. Comparison with a known study of unsupported noble metals suggests that isocyanic acid (HNCO) might be an important intermediate in a reaction system with NO, CO and H₂ present.     

Adsorbate-assisted NO decomposition in NO reduction by C3H6 over Pt/Al2O3 catalysts under lean-burn conditions

The rates and product selectivities of the C₃H₆-NO-O₂ and NO-H₂ reactions over a Pt/Al₂O₃ catalyst, and of the straight, NO decomposition reaction over the reduced catalyst have been compared at 240C. The rate of NO decomposition over the reduced catalyst is seven times greater than the rate of NO decomposition in the C₃H₆-NO-O₂ reaction. This is consistent with a mechanism in which NO decomposition occurs on Pt sites reduced by the hydrocarbon, provided only that at steady state in the lean NO _x reaction about 14% of the Pt sites are in the reduced form. However, the (extrapolated) rate of the NO-H₂ reaction at 240C is about 10⁴ times faster than the rate of the NO decomposition reaction thus raising the possibility that NO decomposition in the former reaction is assisted by H_ads. It is suggested that adsorbate-assisted NO decomposition in the C₃H₆-NO-O₂ reaction could be very important. This would mean that the proportion of reduced Pt sites required in the steady state would be extremely small. The NO decomposition and the NO-H₂ reactions produce no N₂O, unlike the C₃H₆-NO-O₂ reaction, suggesting that adsorbed NO is completely dissociated in the first two cases, but only partially dissociated in the latter case. It is possible that some of the associatively adsorbed NO present during the C₃H₆-NO-O₂ reaction may be adsorbed on oxidised Pt sites.     

NO decomposition and reduction on Pt/Al2O3 powder and monolith catalysts using the TAP reactor

A systematic study over Pt/Al₂O₃ powder and monolith catalysts is carried out using temporal analysis of products (TAP) to elucidate the transient kinetics of NO decomposition and NO reduction with H₂. NO pulsing and NO–H₂ pump-probe experiments demonstrate the effect of catalyst temperature, NO–H₂ pulse delay time and H₂/NO ratio on N₂, N₂O and NH₃ selectivity. At lower temperature (150 °C) decomposition of NO is negligible in the absence of H₂, indicating that N–O bond scission is rate limiting. At higher temperature NO decomposition occurs readily on reduced Pt but the rate is inhibited by surface oxygen as reaction occurs. The reduction of NO by a limiting amount of H₂ at lower temperature indicates the reaction of surface NO with H adatoms to form N adatoms, which react with adsorbed NO to form N₂O or recombine to form N₂. In excess H₂, higher temperatures and longer delay times favor the production of N₂. The longer delay enables NO decomposition on reduced Pt with the role of H₂ being a scavenger of surface oxygen. Lower temperatures and shorter delay times are favorable for ammonia production. The sensitive dependence on delay time indicates that the fate of adsorbed NO depends on the concentration of vacant sites for NO bond scission, necessary for N₂ formation, and of surface hydrogen, necessary for hydrogenation to ammonia. A mechanistic-based microkinetic model is proposed that accounts for the experimental observations. The TAP experiments with the monolith catalyst show an improved signal due to the reduction of transport restrictions caused by the powder. The improved signal holds promise for quantitative TAP studies for kinetic parameters estimation and model discrimination.     

Improvement of Pt/ZrO2 by CeO2 for high pressure CH4/CO2 reforming

CH₄/CO₂ reforming over Pt/ZrO₂, Pt/CeO₂ and Pt/ZrO₂ with CeO₂ was investigated at 2 MPa. Pt/ZrO₂, which shows stable activity under 0.1 MPa, and Pt/CeO₂ showed gradual deactivation with time at the high pressure. The deactivation was suppressed drastically on Pt/ZrO₂ with CeO₂ prepared by different impregnation order (co-impregnation of Pt and CeO₂ on ZrO₂, and consecutive impregnation of Pt and CeO₂ on ZrO₂). The amount of coke deposition was found insignificant and similar among all the catalysts (including Pt/ZrO₂ and Pt/CeO₂). Catalytic activity after the reaction for 24 h was in agreement with Pt particle size after the reaction for same period, indicating that the difference of the catalytic stability is mainly dependent on the extent of Pt aggregation through catalyst preparation, H₂ reduction, and the CH₄/CO₂ reforming. Pt aggregation and the amount of coke deposition were least pronounced on (Pt–Ce)/ZrO₂ prepared by impregnation of CeO₂ on Pt/ZrO₂ and the catalyst showed highest stability.     

High Efficiency of Noble Metal and Metal Oxide Catalyst Systems for the Selective Reduction of NO with Propene in Lean Exhaust Gas

An investigation was conducted of noble metal and metal oxide catalysts deposited on Al₂O₃. The noble metals Pt, Pd, Rh the metal oxides CuO, SnO₂, CoO, Ag₂O, In₂O₃, catalysts were examined. Also investigated were noble metal Pt, Pd, Rh-doped In₂O₃/Al₂O₃ catalysts prepared by single sol–gel method. Both were studied for their capability to reduce NO by propene under lean conditions. In order to improve the catalytic activity and the temperature window, the intermediate addition propene between a Pt/Al₂O₃ oxidation and metal oxide combined catalyst system was also studied. Pt/Al₂O₃ and In₂O₃/Al₂O₃ combined catalyst showed high NO reduction activity in a wider temperature window, and more than 60% NO conversion was observed in the temperature range of 300–550 °C.     

The nature of surface species on modified Pt-based catalysts for the SCR of NO by C<Subscript>3</Subscript>H<Subscript>6</Subscript> under lean-burn condition

The catalytic activity behavior for the selective catalytic reduction of NO by C₃H₆ under excess oxygen and the nature of surface species on the active sites of Pt/Al₂O₃ catalyst after adding a second metal (Fe, Sn, Co, Cr or W) were investigated. It has been found that an important role of second metals is on TONs of C₃H₆ and NO conversions and the nature of surface species produced on the catalyst surface at low temperature instead of the catalytic activity behavior towards the temperature programmed reaction. Although the introduction of each second metal distinctly disturbs the characteristic of surface species, the reaction mechanism is presumably similar. The observation of few surface species and the investigation about their reactivity indicate that few mechanisms are simultaneously proceeding at the same reaction condition.     

Adsorption and interaction of NO, C3H6 and O2 on Pt, Zr, Nb-MCM-41—FTIR study

Adsorption of NO, O₂ and C₃H₆ on the MCM-41 matrices with Nb and Zr loaded with Pt has been studied by the FTIR spectroscopy to characterize these materials as catalysts in the selective reduction of NO with propene. Two types of the catalysts have been studied differing by the methods of Zr and Nb introduction: either by one-pot (group 1) or by post-synthesis impregnation (group 2) and hence by the location of Nb and Zr in the framework (group 1) or extra framework (group 2). It has been found that the positions of these metals in the MCM-41 matrix determine the platinum dispersion, acidic–basic properties and influence the interaction of NO + O₂ + C₃H₆ with the catalyst surfaces. The fact that the Pt dispersion is much higher in group 2 materials has been revealed by results of XRD patterns and TEM images. According to the explanation proposed, the presence of Lewis acid–base pairs in the group 2 of catalysts has strongly activated chemisorption of propene, whereas Lewis basicity, characterized by 2-PrOH dehydrogenation on the samples containing transition metals introduced during the synthesis (group 1), has enhanced chemisorption of nitrite species on platinum. It has been proved that nitrite species have not been stored on Pt/Zr/MCM-41 samples, whereas they have been stabilized on Pt/Zr/Nb/MCM-41 containing BrØnsted acidic centres.     

Synthesis of DME from syngas on the bifunctional Cu–ZnO–Al2O3/Zr-modified ferrierite: Effect of Zr content

The catalytic activity on the coprecipitated Cu–ZnO–Al₂O₃/Zr-ferrierite (CZA–ZrFER) with different Zr content from 0 to 5 wt.% was investigated for the direct synthesis of dimethylether (DME) from H₂-deficient and biomass-derived model syngas (H₂/CO molar ratio = 0.93). The catalytic functionalities, such as CO conversion and DME selectivity, showed their maxima on the bifunctional catalyst with 3 wt.% Zr-modified ferrierite. Detailed characterization studies were conducted on the catalysts to measure their properties such as surface area, acidity by temperature-programmed desorption of ammonia (NH₃-TPD), reducibility of Cu oxide by temperature-programmed reduction (TPR), copper surface area measurements by N₂O titration method, electronic states of copper by IR analysis and particle size measurement by XRD and TEM analysis. The number of acid sites measured by NH₃-TPD on the bifunctional catalysts decreased monotonously with the increase of Zr content, meanwhile, the acidic strength is found to be minimal on the catalyst showing best performance. The reducibility of copper oxide and the surface area of metallic copper also exhibited their maximum values at the same Zr composition indicating that these are responsible for the optimum functionality of the bifunctional CZA–ZrFER catalyst. The role of easily reducible copper species with small particle size and the suppressed strong acidic sites is also emphasized in the consecutive reaction from syngas to DME on the bifunctional catalyst. The different behavior of intrinsic rate of the bifunctional catalysts is also well correlated with the metallic surface area of copper and the amount of acidic sites with their acidic strength.     

Electrochemical lean-deNOx catalyst using H-conducting solid polymer electrolyte

The reduction of NO to N₂/N₂O in the presence of excess O₂ has been successfully achieved at 70 °C using an electrochemical cell of the type, 0.1% NO, 0–10% O₂, Pt | NAFION | Pt, H₂O. An H⁺-conducting solid polymer electrolyte (SPE) plays a key role in evolving hydrogen on the Pt cathode, where the catalytic NO–H₂ takes place. It was revealed that the competitive H₂–O₂ reaction is suppressed because the Pt surface was covered with stable nitrate (NO₃) species, which blocks oxygen adsorption hereon. The inhibition of H₂–O₂ reaction becomes most efficient at 100 °C in agreement with the optimal operation temperature range of SPE. The reduction efficiency of NO in an excess O₂ could be improved by packing 1 wt% Pt/ZSM-5 catalyst in the cathode room. The combination between the SPE cell and Pt catalysts can broadly be applied to novel low-temperature deNO_x processes in a strongly oxidizing atmosphere.     

Catalytic reaction of CH4 with CO2 over alumina-supported Pt metals

The dissociation of CH₄ and CO₂, as well as the reaction between CH₄ and CO₂ at 723–823 K have been studied over alumina supported Pt metals. In the high temperature interaction of CH₄ with catalyst surface small amounts of C₂H₆ were detected. In the reaction of CH₄+CO₂, CO and H₂ were produced with different ratios. The specific activities of the catalysts decreased in the order: Ru, Pd, Rh, Pt and Ir, which agreed with their activity order towards the dissociation of CO₂.This laboratory is a part of the Center for Catalysis, Surface and Material Science at the University of Szeged.     

Kinetic modeling of storage and reduction with different reducing agents (CO, H2, and C2 H4) on a Pt–Ba/-Al2O3 catalyst in the presence of CO2 and H2O

In this paper a global reaction kinetic model is used to understand and describe the NO_x storage/reduction process in the presence of CO₂ and H₂O. Experiments have been performed in a packed bed reactor with a Pt–Ba/γ-Al₂O₃ powder catalyst (1 wt% Pt and 30 wt% Ba) with different lean/rich cycle timings at different temperatures (200, 250, and ) and using different reductants (H₂, CO, and C₂H₄). Model simulations and experimental results are compared. H₂O inhibits the NO oxidation capability of the catalyst and no NO₂ formation is observed. The rate of NO storage increases with temperature. The reduction of stored NO with H₂ is complete for all investigated temperatures. At temperatures above , the water gas shift (WGS) reaction takes place and H₂ acts as reductant instead of CO. At , CO and C₂H₄ are not able to completely regenerate the catalyst. At the higher temperatures, C₂H₄ is capable of reducing all the stored NO, although C₂H₄ poisons the Pt sites by carbon decomposition at . The model adequately describes the NO breakthrough profile during 100 min lean exposure as well as the subsequent release and reduction of the stored NO. Further, the model is capable of simulating transient reactor experiments with 240 s lean and 60 s rich cycle timings.     

Alumina supported Pt(1%)/Ce0.6Zr0.4O2 monolith: Remarkable stabilization of ceria–zirconia solution towards CeAlO3 formation operated by Pt under redox conditions

A structured Pt(1 wt%)/ceria–zirconia/alumina catalyst and the metal-free ceria–zirconia/alumina were prepared, by dip-coating, over a cordierite monolithic support. XRD analyses and Rietveld refinements of the structural data demonstrate that in the Pt supported catalysts ceria–zirconia is present as a Ce_0.6Zr_0.4O₂ homogeneous solid solution and that the deposition over the cordierite doesn’t produce any structural modification. Moreover no Pt sintering occurs.By comparing the XRD patterns recorded on Pt/ceria–zirconia/alumina and ceria–zirconia/alumina after three redox cycles, it results that Pt, favouring the structural reorganization of the ceria–zirconia into one cubic solid solution, prevents any CeAlO₃ formation. On the contrary, such phase due to the interaction between Ce³⁺ and the alumina present in the washcoat is detected when redox cycles are carried out on the ceria–zirconia metal free.Transmission electron microscopy (TEM) investigations of the redox cycled Pt/ceria–zirconia/alumina catalyst detected ceria–zirconia grains with diameter between 10 and 35 nm along with highly dispersed Pt particles (2–3 nm) strongly interacting with ceria.Scanning electron microscopy (SEM) and EDX analyses, recorded on the redox cycled Pt/ceria–zirconia/alumina washcoated monolith evidence a homogeneous distribution of the active components through the channels even after redox aging.Reduction behaviour and CO oxidation activity are in good agreement with the structural modification of the solid solution induced by the redox cycles and reflect the positive effect of Pt/ceria interaction on the catalytic performances.The effect of redox aging on the NO reduction by C₃H₆, in lean conditions, was investigated over the Pt/ceria–zirconia/alumina monolith. The catalyst shows at low temperature (290 °C) good NO removal activity and appreciable selectivity to N₂.     

In situ DRIFTS study of the effect of structure (CeO2–La2O3) and surface (Na) modifiers on the catalytic and surface behaviour of Pt/γ-Al2O3 catalyst under simulated exhaust conditions

The nature and relative populations of adsorbed species formed on the surface of un-promoted and sodium-promoted Pt catalysts supported either on bare Al₂O₃ or CeO₂/La₂O₃-modified Al₂O₃, were investigated by in situ diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS) under simulated automobile exhaust conditions (CO + NO + C₃H₆ + O₂) at the stoichiometric point. The DRIFT spectra indicate that interaction of the reaction mixture with the Pt/Al₂O₃ catalyst leads mainly to formation of formates and acetates on the support and carbonyl species on partially positively charged Pt atoms (Pt^δ+). Although enrichment of Al₂O₃ with lanthanide elements (CeO₂ and La₂O₃) does not significantly modify the carboxylate species formed on the support, it causes significant modification of the oxidation state of Pt, as indicated by the appearance of a substantial population of carbonyl species on reduced Pt sites (Pt⁰–CO). This modification of the Pt component is enhanced when Na-promotion is used, leading to formation of carbonyl species only on electron enriched Pt (i.e., fully reduced Pt⁰ sites) and to the formation of NCO on these Pt entities (2180 cm⁻¹). The latter are thought to result from enhanced NO dissociation at Na-modified Pt sites. These results correlate well with observed differences in the catalytic performance of the three different systems.     

The Role of Support Acidity in the Selective Catalytic Reduction of NO by C3H6 Under Lean-Burn Conditions

Mechanical mixtures consisting of a catalyst (Pt/SiO₂ or Pt/SiO₂–Al₂O₃) and supports of varying acidity (hydrotalcite, SiO₂, SiO₂–Al₂O₃, and ZSM-5 zeolite) were tested for the selective reduction of NO by C₃H₆. A certain degree of support acidity appears to favour N₂ selectivity, but if there are too many acid sites, carbon deposition becomes extensive and leads to catalyst deactivation.     

The functionalities of Pt/γ-Al2O3 catalysts in simultaneous HDS and HDA reactions

A Pt/γ-Al₂O₃ catalyst was tested in simultaneous hydrodesulfurization (HDS) of dibenzothiophene and hydrodearomatization (HDA) of naphthalene reactions. Samples of it were subjected to different pretreatments: reduction, reduction–sulfidation, sulfidation with pure H₂S and non-activation. The reduced catalyst presented the best performance, even comparable to that of Co(Ni)Mo catalysts. All catalyst samples were selective to the HDS reaction over HDA, and to the direct desulfurization pathway of dibenzothiophene HDS over the hydrogenation reaction pathway of HDS. The effect of H₂S partial pressure on the functionalities of the reduced Pt/γ-Al₂O₃ catalyst was studied. The results showed that an increase in H₂S partial pressure does not cause poisoning, but an inhibition effect, without changing the catalyst selectivity. Accordingly, the activity trends were ascribed to adsorption differences between the different reactive molecules over the same catalytic active site. TPR characterization along with a thermodynamics analysis showed that the active phase of reduced Pt/γ-Al₂O₃ is constituted by Pt⁰ particles. However, presulfidation of the catalyst leads to a mixture of PtS and Pt⁰ which has a negative effect on the catalytic performance without changing catalyst functionalities.     

Preparation and Characterization of Pt/Al-ZSM-5 Catalysts and their Reactivities for the Oxidation of CO with N2O at Low Temperatures

Al-ZSM-5 was prepared by treating H-ZSM-5 with an aqueous solution of Al(NO₃)₃ and used as a support for Pt catalysts. The Pt-loaded Al-ZSM-5 acts as an efficient catalyst for CO oxidation with N₂O at 273 K. TEM investigations revealed that Pt clusters with an average particle size of around 1–1.5 nm were homogeneously dispersed within Al-ZSM-5. Moreover, FT-IR and XPS analyses indicated that the small Al₂O₃ clusters formed within Al-ZSM-5 plays a significant role in the formation of highly dispersed Pt clusters within the pore structure of the ZSM-5 zeolite, leading to the high catalytic activity of Pt/Al-ZSM-5 as compared to Pt/ZSM-5.     

Hydrogen–deuterium isotope effects in the reactions of chlorobenzene and benzene on a Pt/γ-Al2O3 catalyst

The kinetic isotope effect for combustion of a C₆H₅Cl/C₆D₅Cl mixture on Pt/-Al₂O₃ was found to be close to unity between 520 and 580 K. However, in the presence of an excess of heptane, an isotope effect of 1.5 was found between 460 and 490 K. For the combustion of a C₆H₆/C₆D₆ mixture the k_H/k_D value was around 2 between 404 and 439 K. The results show that in the combustion of chlorobenzene per se, C–H bond activation is not a rate-determining step. On Pt sites, C–Cl bond scission probably occurs already at low temperatures. The chlorine and the phenyl group cannot easily react further. Chlorine on the surface is active in chlorination, which is shown by the formation of C₆D₅Cl in an experiment with C₆H₅Cl and C₆D₆. Only at a certain temperature is the chlorine removed, partly as polychlorinated benzenes. The removal of chlorine from the catalyst allows oxygen to take part in the reaction, which determines the rate of the combustion of chlorobenzene. When heptane is present, Cl is removed from the surface and C–H bond scission can become rate determining, as is also the case in the combustion of C₆H₆/C₆D₆. Upon (partial) combustion of C₆H₅Cl/C₆D₅Cl and C₆H₆/C₆D₆ mixtures on a Pt/-Al₂O₃ catalyst, hydrogen–deuterium exchange occurs on the -Al₂O₃ support.     

Effect of the support on the mechanism of partial oxidation of methane on platinum catalysts

The partial oxidation of methane was studied on Pt/Al₂O₃, Pt/ZrO₂, Pt/CeO₂ and Pt/Y₂O₃ catalysts. For Pt/Al₂O₃, Pt/ZrO₂ and Pt/CeO₂, temperature programmed surface reaction (TPSR) studies showed partial oxidation of methane comprehends two steps: combustion of methane followed by CO₂, and steam reforming of unreacted methane, while for Pt/Y₂O₃ a direct mechanism was observed. Oxygen Storage Capacity (OSC) evaluated the reducibility and oxygen transfer capacity of the catalysts. Pt/CeO₂ catalyst showed the highest stability on partial oxidation. The results were explained by the higher reducibility and oxygen storage/release capacity which allowed a continuous removal of carbonaceous deposits from the active sites, favoring the stability of the catalyst, For Pt/Al₂O₃ and Pt/ZrO₂ catalysts the increase of carbon deposits around or near the metal particle inhibits the CO₂ dissociation on CO₂ reforming of methane. Pt/Y₂O₃ was active and stable for partial oxidation of methane, and its behavior was explained by a change in the reaction mechanism.     

The effect of sodium on the catalytic activity of ZnO–Al2O3/ZSM-5 and SnO–Al2O3/ZSM-5 for the transesterification of vegetable oil with methanol

In order to elucidate the effect of sodium on the activity of ZSM-5 supported metal oxides catalysts (ZnO–Al₂O₃/ZSM-5 and SnO–Al₂O₃/ZSM-5) for the transesterification of soybean oil with methanol, ZSM-5 supported metal oxides were prepared with and without sodium hydroxide by impregnation. The metal compositions of the ZSM-5 supported metal oxide catalysts and the metal concentrations dissolved from the catalysts to the methylester phase were measured by SEM-EDS and inductive coupled plasma spectroscopy, respectively. The catalytic activity of ZnO–Al₂O₃/ZSM-5 and SnO–Al₂O₃/ZSM-5 containing sodium did not originate from surface metal oxides sites, but from surface sodium sites or dissolved sodium leached from the catalyst surface.     

The promotional effect of Cr on catalytic activity of Pt/ZSM-35 for H2-SCR in excess oxygen

Selective catalytic reduction of NO by hydrogen was studied over Cr modified Pt/ZSM-35 catalysts. The preparation process greatly influenced catalytic activity and sample prepared by co-impregnation method exhibits the best activity. In situ DRIFT studies revealed that on Pt–Cr/ZSM-35, (1) new Pt-NO^δ+ and NO species adsorbed on Pt were detected upon NO + O₂ adsorption; (2) much more ammonia species were formed under reaction condition. Cr addition not only enhanced the adsorption of NO_x but also promoted the formation of surface NH₄⁺ species, which should be the origin of promotional effect of Cr on Pt/ZSM-35 for H₂-SCR reaction.