复合砂浆钢筋网加固抗弯RC梁的非线性分析

复合砂浆钢筋网薄层加固是一种有效的加固方法,能够显著地提高钢筋混凝土梁的抗弯承载力、变形能力以及抗裂性能。以8根复合砂浆钢筋网加固RC梁的试验研究结果为参考,通过非线性有限元分析广泛地研究了加固梁纵向配筋率、配箍特征值、梁高宽比对极限荷载提高幅度的影响,并初步分析了少筋梁和超筋梁加固后的荷载-跨中挠度曲线的变化规律。根据分析和试验结果,通过等效假定给出了复合砂浆钢筋网加固RC梁的极限承载力计算公式和抗弯刚度计算公式。     

预应力钢板箍加固RC短柱抗剪承载力试验研究

进行了9个采用预应力钢板箍(Prestressed Steel Jacket,PSJ)加固的RC短柱试件的单调加载试验。重点研究预应力钢板箍加固RC短柱的抗剪性能和加固构件受剪承载力计算方法。主要试验参数包括箍板预应力度和箍板配置量。试验结果表明:采用预应力钢板箍加固RC短柱可显著改善其受剪性能,不仅可有效提高构件的抗剪承载力,并能使最终出现剪切破坏的加固短柱具有较好的变形能力。在试验研究基础上探讨了预应力箍板加固的受剪机理,分析了各主要参数对加固柱受剪承载力的影响及其规律。分析结果表明:预应力箍板的受剪系数与箍板预应力度和箍板配箍特征值等因素有关。基于叠加方法,提出了箍板受剪系数和加固柱抗剪承载力计算公式,计算结果和试验结果总体吻合良好。研究成果可为预应力钢板箍加固RC柱的抗剪设计提供依据。     

CFRP网格-聚合物水泥砂浆加固RC梁抗剪承载力计算方法

为揭示碳纤维增强树脂复合材料(Carbon fiber reinforced polymer,CFRP)网格-聚合物水泥砂浆(Polymer cement mortar,PCM)抗剪加固钢筋混凝土(RC)梁的受剪机制并建立其承载力计算方法,对RC梁进行了四点弯曲试验和有限元模拟,重点分析了CFRP网格对RC加固梁的抗剪贡献,建立了基于改进的桁架拱模型的抗剪承载力计算方法。结果表明：RC梁侧粘贴CFRP网格-PCM加固层不仅可以抑制斜裂缝的发展,而且还提高了抗剪承载力;CFRP网格与钢筋之间具有良好的协同工作性能,其中,横向CFRP网格筋分担了约16%的箍筋应变;回归分析指出纵向CFRP网格筋的应变约为横向CFRP网格筋应变的0.29倍;综合考虑纵向CFRP网格的销栓作用和横向CFRP网格分担的箍筋应变,提出了基于改进桁架-拱模型的承载力计算方法,具有更好的适用性和准确性,能够满足设计要求。     

纤维织物增强高延性混凝土加固受损RC梁受剪性能试验

为研究二次受力对纤维织物增强高延性混凝土(TRHDC)加固钢筋混凝土(RC)梁受剪性能的影响,对8根TRHDC加固梁和1根对比梁进行了静载试验,分析了纤维织物层数、损伤程度及持载水平对梁破坏形态、荷载-挠度曲线、荷载-箍筋应变曲线及荷载-织物应变曲线的影响。试验结果表明：所有梁均发生了剪压破坏,仅一根梁出现剥离现象;TRHDC可有效限制斜裂缝的发展,延缓箍筋屈服和刚度退化;TRHDC加固显著地提高了梁的受剪承载力和变形能力,最高分别达67%和54%;加固效果未完全随纤维织物层数的增大而提高,与TRHDC面层利用率有关;原梁箍筋屈服之前,损伤程度对加固梁受剪性能的影响不明显,原梁箍筋屈服之后,加固梁受剪承载力随损伤程度的增大而降低;加固效果随持载水平的提高而降低;两层纤维织物的TRHDC可有效修复完全受损RC梁的受剪性能;建立了考虑二次受力的TRHDC加固RC梁受剪承载力的计算公式,且计算值与试验结果吻合较好。     

U型箍加固锈蚀RC梁的抗弯性能试验研究及数值分析

为研究U型箍加固和二次锈蚀对锈蚀RC梁力学性能的影响,该文通过设计7片试验梁,分析构件的应变规律、变形特征、破坏机理等,并采用ABAQUS有限元软件进行了数值模拟,探讨U型箍加固厚度与加固位置对加固梁性能的影响。结果表明,试验梁跨中截面应变满足平截面假定,中和轴高度大致符合这个规律:锈蚀梁以及锈蚀加固再锈蚀梁的中和轴高度均要大于加固锈蚀梁的高度;荷载增大到一定时,U型箍的锚固作用开始发挥作用;加载中后期,同侧三片U型箍分担的剪力存在不均匀性;腐蚀不均匀导致两端的U型箍应变增长规律有差异;加固梁、加固锈蚀梁的裂缝更稀疏,裂缝趋向于跨中区域分布,斜裂缝逐渐变得不明显; U型箍加固梁的开裂荷载与极限荷载有所提高,塑性特征更为明显,主要呈现为弯剪破坏;二次锈蚀和不均匀性会改变构件变形发展,影响梁的破坏形态。数值模拟的极限荷载、极限荷载对应的挠度以及能量吸收值与试验结果的误差分别在4.22%、9.7%、9.9%范围以内,设置3 mm的加固厚度对提高承载力较为适宜,U型箍布置在梁端位置可更好地提高构件的强度和刚度。     

U形CFRP条带混锚加固混凝土梁抗剪试验

为解决纯粘贴U形纤维增强聚合物基复合材料（FRP）加固钢筋混凝土梁中FRP端部容易发生剥离破坏等问题,自主研发了对纤维布条带端部进行自锁锚固的方法和锚板,提出了端锚与粘贴并用的混锚U形条带抗剪加固方法。通过2根未加固梁、1根纯粘贴和2根混锚U形碳纤维增强聚合物基复合材料（CFRP）带抗剪加固梁的对比试验,证实了混锚抗剪加固的有效性：混锚能够对纤维带端部进行可靠锚固,阻止端部剥离破坏的发生,实现纤维拉断破坏,大幅度提高材料强度利用率。混锚加固在抑制混凝土梁斜裂缝开展、延缓箍筋屈服、提高箍筋和CFRP的极限应变以及提高抗剪承载力等多个方面的表现均明显优于纯粘贴加固。     

钢筋混凝土梁动态剪切性能及尺寸效应细观研究EI北大核心CSCD

基于ABAQUS有限元数值计算平台,考虑混凝土材料的非均质性以及钢筋和混凝土的应变率效应,建立了钢筋混凝土(reinforced concrete,RC)梁三维细观数值分析模型,探究了RC梁在不同应变率和配箍率条件下的剪切性能及其尺寸效应行为。结果表明:剪切承载力随着应变率和配箍率的增加均有不同程度的提高;名义抗剪强度随梁高的增大而减小,存在显著的尺寸效应现象;应变率和配箍率的增大一方面可以提高RC梁的名义抗剪强度,另一方面会削弱名义抗剪强度的尺寸效应行为;提出的RC梁静/动态剪切统一尺寸效应律同时考虑了尺寸效应、应变率效应和配箍率的影响,能够较好地预测RC梁在静态和动态作用下的名义抗剪强度,具有一定的准确性和合理性。     

纤维网格高延性混凝土加固RC柱抗剪性能试验研究

箍筋配置不当、剪跨比较小和轴压比较大的钢筋混凝土(RC)框架柱在地震作用下通常发生脆性剪切破坏。为提高框架柱的抗剪性能,提出采用碳纤维(CFRP)网格和高延性混凝土(HDC)复合加固RC柱。设计了6个RC柱试件,通过低周反复荷载试验,研究加固方式、纤维网格层数和轴压比对加固柱破坏形态、受剪承载力、延性及耗能能力的影响。结果表明:采用HDC和CFRP网格复合加固,可显著提高柱的抗剪承载力,明显改善其延性、变形性能和耗能能力;提高加固层的网格层数,对抗剪承载力影响较小,但加固柱的延性和变形能力得到较大改善;轴压比增大,复合柱的抗剪承载力稍有提高,但试件的延性、变形能力和耗能能力均降低;增加网格层数对高轴压比加固柱的增强效果和对低轴压比柱基本一致。最后基于桁架-拱模型,提出加固柱的抗剪承载力计算公式,计算结果与试验值吻合较好。     

CFRP布加固方案对RC梁剪切性能及尺寸效应影响分析EI北大核心CSCD

采用同时考虑混凝土材料非均质性、钢筋与混凝土之间的相互作用以及CFRP布与混凝土之间的相互作用影响的三维细观数值模拟方法,建立了CFRP布加固RC梁剪切破坏力学分析模型。在验证了细观数值方法合理性的基础上,设计并建立了12根CFRP布加固RC梁细观模型,探究相同CFRP配纤率(用布量)前提下,不同CFRP布加固方案对单调荷载作用下RC梁的剪切性能及尺寸效应的影响。结果表明:CFRP布应变分布与裂缝位置紧密相关,越靠近裂缝位置的CFRP布应变越大,提供的抗剪贡献越多;在CFRP配纤率一致的前提下,CFRP布宽度大厚度小的加固方案优于CFRP布厚度大宽度小的加固方案;CFRP布U型加固RC梁剪切强度存在尺寸效应现象,但相同CFRP配纤率下,不同CFRP布加固方案对名义抗剪强度尺寸效应的影响较小,可以忽略。     

高延性混凝土加固钢筋混凝土梁受剪性能试验研究及承载力计算

为研究高延性混凝土(HDC)加固钢筋混凝土梁的受剪性能,该文对7根HDC加固梁及4根未加固梁进行静力试验,研究剪跨比、配箍率、加固层厚度和加固层附加箍筋对钢筋混凝土梁破坏形态、荷载-挠度曲线、受剪承载力以及裂缝的影响。结果表明:采用HDC面层对钢筋混凝土梁进行受剪加固,可以显著提高梁的受剪承载力;HDC面层可以代替部分箍筋的受剪作用,改善钢筋混凝土梁的剪切破坏形态;加固试件在达到极限位移之后,试件的完整性较好,剩余承载力较高。基于试验结果,利用桁架-拱模型,提出了HDC加固钢筋混凝土梁的受剪承载力计算公式,计算值与试验值吻合较好。     

An experimental investigation on flexural behavior of RC beams strengthened with prestressed CFRP strips using a durable anchorage system

This paper investigates the effectiveness and feasibility of a prestressed carbon fiber-reinforced polymer (CFRP) system for strengthening reinforced concrete (RC) beams. The proposed prestressing system with a novel anchorage allows the utilization of full capacity of the CFRP strips. Eight small-scale and two large-scale concrete beams strengthened different configuration of prestressed CFRP strips are tested under static loading conditions up to failure. The main parameters considered include the level of prestressing applied, ranging from 20% to 70% of the tensile strength of the CFRP strips, and the use of mechanical anchorages at both ends of the CFRP strips. Thanks to the durable anchorage, the full range of flexural behavior was investigated including post-debonding. The results indicate that the beams strengthened using prestressed CFRP strips exhibited a higher first-cracking, steel-yielding, and experimental nominal moments as the level of prestressing force increased up to a certain point. After analyzing prestress effects in small scale tests, an optimum prestress level for strengthening concrete beams using CFRP strips is proposed and verified in large scale tests.     

高强钢绞线网——聚合物砂浆加固混凝土及预应力混凝土梁的抗弯性能试验研究

该文侧重研究了采用高强钢绞线网——聚合物砂浆加固技术三面加固普通钢筋混凝土(RC)梁和预应力混凝土(PRC)梁的抗弯性能.进行了6 片RC 梁及5 片PRC 梁的抗弯静载试验,探讨了不同初始损伤程度、有效预应力大小和加载方式等对高强钢绞线网——渗透性聚合物砂浆加固梁的抗弯性能影响.结果表明:采用高强钢绞线网——聚合物砂浆加固技术加固RC/PRC梁能够有效抑制裂缝的开展,能有效地提高RC/PRC 加固梁的抗弯承载能力和抗弯刚度;重复加载会导致加固梁刚度一定程度的退化,初始损伤程度大小不会显著改变加固后RC/PRC梁的抗弯承载力;该文研究对于大量既有RC/PRC梁的抗弯加固具有一定的参考价值.     

Behavior of RC T-section beams strengthened with CFRP strips,subjected to cyclic load

This paper presents results of an experimental investigation on T-section reinforced concrete (RC) beams strengthened with externally bonded carbon fiber-reinforced polymer (CFRP) strips. Specimens, one of which was the control specimen and the remaining six were the shear deficient test specimens, were tested under cyclic load to investigate the effect of CFRP strips on behavior and strength. Five shear deficient specimens were strengthened with side bonded and U-jacketed CFRP strips, and remaining one tested with its virgin condition without strengthening. The type and arrangement of CFRP strips and the anchorage used to fasten the strips to the concrete are the variables of this experimental work. The main objective was to analyze the behavior and failure modes of T-section RC beams strengthened in shear with externally bonded CFRP strips. According to test results premature debonding was the dominant failure mode of externally strengthened RC beams so the effect of anchorage usage on behavior and strength was also investigated. To verify the reliability of shear design equations and guidelines, experimental results were compared with all common guidelines and published design equations. This comparison and validation of guidelines is one of the main objectives of this work. The test results confirmed that all CFRP arrangements differ from CFRP strip width and arrangement, improved the strength and behavior of the specimens in different level significantly.     

高延性混凝土加固钢筋混凝土梁抗震性能试验研究

为研究高延性混凝土(HDC)加固钢筋混凝土(RC)梁的抗震性能,设计了8个RC梁试件,采用HDC和碳纤维布(CFRP)条带加固,通过低周反复荷载试验,研究剪跨比、加固方式对其破坏形态、变形和耗能能力等的影响。试验结果表明:采用HDC围套加固RC梁,HDC面层良好的拉伸应变硬化和多裂缝开展特性能有效控制剪切裂缝发展,明显改善构件的脆性破坏特征;HDC加固层与原构件协同工作良好,加固层对内部混凝土形成良好的约束作用,HDC加固梁的承载力、变形和耗能能力明显提高,其加固效果明显优于CFRP条带加固;剪跨比较大时,在HDC加固层配置钢筋网,试件的变形和耗能能力明显提高,但对承载力贡献较小。基于桁架-拱模型理论,提出HDC加固梁的抗剪承载力计算方法,计算结果与试验值吻合较好。     

剪跨比对CFRP加固无腹筋混凝土梁剪切破坏及尺寸效应的影响研究

剪跨比对FRP抗剪加固梁的裂缝开展和破坏模式有重要影响,但对FRP加固梁抗剪强度及尺寸效应的影响研究较少。采用三维细观数值模拟方法,考虑混凝土细观组成的非均质性及碳纤维布(CFRP)与混凝土之间的相互作用,建立了CFRP加固无腹筋钢筋混凝土梁剪切破坏力学分析模型。在验证细观模拟方法合理性的基础上,拓展模拟与分析了剪跨比对CFRP加固钢筋混凝土梁剪切破坏及尺寸效应的影响机制与规律。研究结果表明:剪跨比对CFRP抗剪加固梁剪切破坏模式影响较大,剪跨比越大,加固梁愈趋近于延性较好的斜拉破坏;剪跨比对CFRP加固梁抗剪承载力有较大影响,对抗剪强度尺寸效应影响较小;剪跨比对加固梁中的CFRP剪切贡献影响较大,剪跨比越大,CFRP对加固梁的抗剪效果越好,其中对中型剪跨比(λ=2.5)的梁加固效果最有效。     

Nonlinear finite element modeling of concrete deep beams with openings strengthened with externally-bonded composites

This paper aims to develop 3D nonlinear finite element (FE) models for reinforced concrete (RC) deep beams containing web openings and strengthened in shear with carbon fiber reinforced polymer (CFRP) composite sheets. The web openings interrupted the natural load path either fully or partially. The FE models adopted realistic materials constitutive laws that account for the nonlinear behavior of materials. In the FE models, solid elements for concrete, multi-layer shell elements for CFRP and link elements for steel reinforcement were used to simulate the physical models. Special interface elements were implemented in the FE models to simulate the interfacial bond behavior between the concrete and CFRP composites. A comparison between the FE results and experimental data published in the literature demonstrated the validity of the computational models in capturing the structural response for both unstrengthened and CFRP-strengthened deep beams with openings. The developed FE models can serve as a numerical platform for performance prediction of RC deep beams with openings strengthened in shear with CFRP composites.     

NSM shear strengthening technique with CFRP laminates applied in high-strength concrete beams with or without pre-cracking

The effectiveness of the near surface mounted (NSM) shear strengthening technique with carbon fiber reinforced polymer (CFRP) laminates applied in high-strength concrete beams with a certain percentage of existing steel stirrups is assessed by experimental research. In this context, the influence of the following main parameters are investigated: (i) the percentage and the inclination of the CFRP laminates; (ii) the percentage of existing steel stirrups; (iii) the existence of cracks when the reinforced concrete (RC) beams are shear strengthened with NSM CFRP laminates. The results showed that the NSM shear strengthening technique with CFRP laminates is more effective when applied to RC beams of high-strength concrete, not only in terms of increasing the load carrying capacity of the beams, but also in assuring higher mobilization of the tensile properties of the CFRP. Inclined laminates were more effective than vertical laminates and the shear resistance of the beams has increased with the percentage of laminates. Pre-cracked RC beams strengthened with NSM CFRP laminates have presented a load carrying capacity similar to that of the homologous uncracked strengthened beams.     

Interfacial shear stress concentration in FRP-strengthened beams

This paper reports the results of an experimental programme designed to study the interfacial shear stress concentration at the plate curtailment of reinforced concrete (RC) beams strengthened in flexure with externally bonded carbon fibre-reinforced polymer (CFRP). Specifically, the study looks at the relationship between the CFRP plate thickness and the interfacial shear stress concentration at the plate curtailment, the failure modes of the CFRP-strengthened beams as well as the efficiency of the CFRP external reinforcing system. Comparing the experimental results with existing models' predictions is another objective of this study. The experimental programme included five RC beams 115 mm×150 mm in cross-section and 1500 mm in length. Four of the RC beams were reinforced externally with CFRP plates of different thicknesses. Tests in this study showed that the thickness of CFRP plate affects not only the load-carrying and deflection capacities of the strengthened beam, but also the shear stress concentration at the CFRP/concrete interface and the beam failure mode.