New associative systems based on alkylated hyaluronic acid. Synthesis and aqueous solution properties

This paper concerns the preparation of new water-soluble alkylated derivatives of hyaluronan (HA); these derivatives were synthesized under mild aqueous and well controlled conditions. The first step was to prepare a HA derivative selectively modified with adipic dihydrazide (HA-ADH) with a substitution degree of 0.08; then, alkyl chains with different chain lengths were introduced with a substitution degree around 0.05. These polymers being still water-soluble exhibit associating properties in the presence of external salt. Formation of hydrophobic domains is demonstrated from fluorescence measurements in the presence of pyrene as a probe. Then, it is shown that the viscosity of polymer solutions in 0.1 M NaCl becomes non-Newtonian for HA grafted with C-10 and C-12 chains and increases rapidly with the polymer concentration over 1 g/L. When the polymer concentration increases, a gel-like behaviour was observed from rheological measurements with the G′ modulus larger than G″ in all the frequency range covered. The dependence of the shear stress on shear rate applied according to a continuous linear ramp provided evidence of the deformation or rupture of aggregates. The latter were shown to reform slowly. At the end, the influence of temperature was examined: first a slight increase in the modulus was observed followed by a decrease corresponding to reinforcement of the hydrophobic interactions.     

Solvent dependence of the viscous and viscoelastic properties of a high molecular weight polystyrene in moderately concentrated solution

The steady-flow viscosity and viscoelastic behaviour of two solutions of a sensibly monodisperse polystyrene of high molecular weight (M_w = 498 000) have been measured over a temperature range of 100°C for identical concentrations of 20.55 wt.%. Toluene and methyl ethyl ketone were chosen as the two low viscosity solvents having, respectively, good and marginal thermodynamic affinities. Dynamic viscoelastic measurements were made at a frequency of 41 kHz using travelling torsional waves. At this frequency, both solutions exhibit behaviour characteristic of the rubbery region, and the ratio of the dynamic viscosity normalised by dividing by the corresponding solvent viscosity is independent of the solvent until the onset of the glass transition region with decreasing temperature. The storage shear modulus of the toluene solution in the rubbery region is higher than for the MEK solution, indicating a higher entanglement density in the better solvent and a larger polymer radius. Some features of the results in the poor solvent (MEK) appear to indicate that, as the temperature decreases, partial exclusion of the solvent leads to the formation both of stronger entanglements and of macromolecular aggregates or bundles, as suggested by Dreval and others^6–8,11,22.     

Rheological properties of poly(methyl methacrylate)/rigid ladderlike polyphenylsilsesquioxane blends

A series of poly(methyl methacrylate) (PMMA) blends with rigid ladderlike polyphenylsilsesquioxane (PPSQ) were prepared at weight ratios of 100/0, 95/5, 90/10, 85/15, and 80/20 by solution casting and then hot‐pressing. Their rheological properties have been studied under both dynamic shear and uniaxial elongation conditions. Their rheological properties depend on the compositions. The storage modulus, G′, loss modulus, G″, and dynamic shear viscosity, η*, of the PMMA/PPSQ 95/5 blend were slightly lower than those of pure PMMA. However, the values of G′, G″, and η* for the other PMMA/PPSQ blends are higher than those of PMMA. The G′ values increase with an increase in PPSQ content from 5% through 15% PPSQ at low frequencies and then drop as the PPSQ content increases to 20%. Uniaxial elongational viscosity (η_E) data demonstrate that PMMA/PPSQ blends exhibit slightly weaker (5% PPSQ) and much weaker (10% PPSQ) strain‐hardening than PMMA. In contrast, the PMMA/PPSQ 85/15 blend shows strain‐softening. Neither strain‐hardening nor strain‐softening was observed in the 80/20 blend. The special rheological properties for the 95/5 blend is probably due to a decrease in PMMA entanglements brought by the specific PMMA–PPSQ interactions. Rheological properties of PMMA/PPSQ blends with higher PPSQ content (≥10%) are mainly affected by formation of hard PPSQ particles. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 352–359, 2007     

Anomalous Viscosity Behavior in Aqueous Solutions of Hyaluronic Acid

Summary Effects of steady shear flows on intermolecular interactions in dilute and semidilute aqueous solutions of hyaluronic acid (HA) are reported. Pronounced shear thinning behavior is observed for solutions of HA at high shear rates, and no hysteresis effects are detected upon the subsequent return to low shear rates. With the aid of the asymmetric flow field-flow fractionation (AFFFF) technique, it is shown that mechanical degradation of the polymer does not take place in these shear viscosity experiments, even at high shear rates. The low shear rate viscosity of a semidilute HA solution decreases by approximately 40% when the temperature is increased from 10 °C to 45 °C. It is shown that when a dilute HA solution is exposed to a low fixed shear rate (0.001 s^-1), a marked viscosification occurs in the course of time and prominent intermolecular complexes are formed. It is argued that shear-induced alignment and stretching of polymer chains promote the evolution of hydrogen-bonded structures, where cooperative zipping of stretched chains generates a network. At a higher constant shear rate (0.1 s^-1), the viscosity decreases as time goes because of the alignment of the polymer chains, but the higher shear flow perturbation prevents the chains in dilute solutions from building up association complexes. The viscosity of an entangled HA solution is not changed in the considered time window at this shear rate, but the network structures breakdown at the highest shear rate (1000 s^-1), and then they are restored upon return to a low shear rate.     

Rheological studies of hyaluronan solutions based on the scaling law and constitutive models

We have investigated the scaling relationship between rheological behavior and concentration for both salt-free and saline solutions of hyaluronan (HA), and adopted three viscoelastic constitutive models to predict the linear/non-linear viscoelastic behavior of these aqueous solutions of HA with different molecular weights at different concentrations up to 20 mg/ml. A series of concentration equations are obtained to describe the influence of HA concentration on solution viscosity. Corresponding to dilute and semi-dilute concentration region, salt-free HA solutions have scaling relationship between specific viscosity and HA concentration as η_sp ∼ c^1.0 and η_sp ∼ c^3.5, respectively, while for 0.15 M NaCl HA solutions, the scaling exponents are 1.5 and 4.2, respectively. Simulation results indicate that these constitutive models have good applicability to describe quantitatively the rheological properties of HA entangled solutions under either dynamic or steady shear flow. In addition, the plateau modulus scaling of HA solutions can be well described by the concentration-dependent length scale.     

Structure–rheology relationship in complex quaternized polysulfones/solvent/nonsolvent systems

Polymer chains consisting of water-soluble polysulfones with various amounts of ionic chlorine have been prepared via the quaternization reaction of chloromethylated polysulfones with N,N-dimethylethanolamine. Rheological investigations have reflected the importance of electrostatic interactions, hydrogen bonding, and association phenomena from the ternary systems consisting of a proton-acceptor polymer (polysulfones with different ionic chlorine content), a proton-donor solvent (N,N-dimethylformamide), and a proton-donor solvent (methanol). The specific interactions, the polyelectrolyte effect induced by enhanced dissociation of the ionizable groups and mixed solvents’ quality modify the rheological functions, i.e., dynamic viscosity, elastic shear modulus and viscous shear modulus, as well as the thermodynamic parameters obtained from the rheological properties, such as apparent energy of activation and flow activation entropy. These results were correlated with the surface properties of the polysulfonic films formed from solutions in solvent/nonsolvent mixtures.     

Rheological properties of polystyrene blends with rigid ladderlike polyphenylsilsesquioxane

Polystyrene (PS) blends with rigid ladderlike polyphenylsilsesquioxane (PPSQ) were prepared by solution casting followed by hot pressing. The rheological properties of these blends were studied under dynamic shear and uniaxial elongation conditions. The loss modulus (G″) and dynamic shear viscosity (η*) of the 95/5 PP/PPSQ blend were slightly lower than those of pure PS at low frequencies (≤10^?2 rad/s). However, the storage modulus (G′), G″, and η* of the other blends (90/10, 85/15, and 80/20) were higher than those of pure PS and increased with PPSQ content. The η_E data demonstrated that PS/PPSQ blends exhibited slightly weaker (5% PPSQ) or much weaker (10% PPSQ) strain hardening than PS. In contrast, the 85/15 and 80/20 PP/PPSQ blends showed strain softening, and the extent of strain softening increased with PPSQ content. PS entanglements might have been reduced by the specific interactions between PS and PPSQ, which locally ordered some PS molecules in the 95/5 blend sample, because most of the PPSQ might have been well dispersed in the PS continuous phase, and only a few small PPSQ particles (～1.3 μm) were formed because of good miscibility. However, at high PPSQ contents (≥10%), many larger hard PPSQ particles were formed, which acted as fillers during the rheological measurements. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 96: 706–713, 2005     

A study of rheological behavior of a polypyrrole modified UHMWPE gel using a parallel plate rheometer

Polypyrrole powder was added to a 6% UHMWPE decalin solution as an interfacial modifier. Rheological properties and dynamic viscoelastic properties, including shear viscosity, shear storage modulus (G′), and shear loss modulus (G″), were measured with a parallel plate rheometer using rotation and oscillation modes. The results show that these properties increase with the PPy content. In addition, the gelation temperature decreased with increasing PPy content. This suggests that the presence of PPy enhanced the entanglement network in the solution, which is similar to the role of filler in rubber.     

Rheological aspects of microbial hyaluronic acid

The rheological properties of the hyaluronic acid (HA) produced by the cultivation of Streptococcus zooepidemicus ATCC 39920 in synthetic medium at constant pH of 7.0 were determined. Relevant characteristics of the biopolymer as its pureness related to proteins (0.44 mg of protein per gram of HA) and its average molar weight (4.0 × 10⁶ Da) were also determined. Experimental data in steady shear (flow curves) have been correlated with the Cross model, which described the apparent viscosity shear rate data well mainly at concentrations higher than 50 mg mL^?1.The concentration dependence of specific viscosity showed two linear regimes that intercept at critical overlap concentration (c*) equal to 4 mg mL^?1. The storage (G′) and loss (G″) moduli increasing along the HA concentration and estimates out of the studied range indicate that a crossover frequency decreased with the increasing concentration of HA. The high concentration dependence of G′ as well as the deviations of the Cox‐Merz rule for most of the HA concentrations indicate the hyperentangled properties for the HA chains, which could be visualized through atomic force microscopy images even at low concentrations as 0.01 mg mL^?1. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011.     

Rheological non-Newtonian behaviour of ethylene glycol-based Fe2O3 nanofluids

The rheological behaviour of ethylene glycol-based nanofluids containing hexagonal scalenohedral-shaped α-Fe₂O₃ (hematite) nanoparticles at 303.15 K and particle weight concentrations up to 25% has been carried out using a cone-plate Physica MCR rheometer. The tests performed show that the studied nanofluids present non-Newtonian shear-thinning behaviour. In addition, the viscosity at a given shear rate is time dependent, i.e. the fluid is thixotropic. Finally, using strain sweep and frequency sweep tests, the storage modulus G'', loss modulus G″ and damping factor were determined as a function of the frequency showing viscoelastic behaviour for all samples.     

Rheology of PVC. Part 5: Melt elasticity

The behavior of PVC changes drastically with the temperature and the method of sample preparation. In the steady-state shear mode, upon a decrease of the rate of deformation, the data may show either a steady increase of the shear viscosity or a leveling off to a Newtonian plateau. In the dynamic test mode, both the storage modulus, G′, and the loss modulus, G″, show an effect of the yield stress. Only at temperatures above 210°C are flow curves normal for polymer melts obtained. Rigid and nonrigid PVC formulations have been tested in Weissenberg Rheogoniometer, using steady-state or dynamic test modes at temperatures from 140 to 220°C. It was observed that yield affects elasticity more (measured by the first normal stress difference or the storage modulus) than viscosity (expressed by the shear stress or the loss modulus). The corrected for yield plots of elastic vs. viscous parameter can be easily interpreted in terms of a composite flow.     

Effects of swelling on the viscoelastic properties of polyester films made from glycerol and glutaric acid

Viscoelastic properties have been determined for poly(glycerol‐co‐glutaric acid) films synthesized from Lewis acid‐catalyzed polyesterifications. The polymers were prepared by synthesizing polymer gels that were subsequently cured at 125°C to form polymer films. The polymers were evaluated for the extent of reaction before and after curing by Fourier transform infrared spectroscopy. They were subsequently immersed in dimethylsulfoxide, tetrahydrofuran, water, methanol, and hexane for 24 h. The amounts of solvent absorbed were monitored and recorded. Dependent up the solvent used, the polymers were able to absorb 9.5–261% of its weight. The effects of the solvent absorption on the viscoelastic properties of the polyester films were evaluated by determining their elastic modulus (G′), viscous modulus (G″), tan δG″/G′, and complex viscosity (η*) by performing oscillatory frequency sweep experiments. The elastic modulus (G′) and viscous modulus (G″) were both higher for the dry polymers than the solvent‐absorbed polymers. However, the polymer films were all higher in elastic (G′) character than viscous (G″) character. Therefore, tan δG″/G′ < 1 before and after immersion in solvents. Values for η* decreased with angular frequency for all of the polyesters tested in this study. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Morphology and melt rheology of nylon 11/clay nanocomposites

Nylon 11 (PA11)/clay nanocomposites have been prepared by melt‐blending, followed by melt‐extrusion through a capillary. Transmission electron microscopy shows that the exfoliated clay morphology is dominant for low nanofiller content, while the intercalated one is prevailing for high filler loading. Melt rheological properties of PA11 nanocomposites have been studied in both linear and nonlinear viscoelastic response regions. In the linear regime, the nanocomposites exhibit much higher storage modulus (G′) and loss modulus (G″) values than neat PA11. The values of G′ and G″ increase steadily with clay loading at low concentrations, while the G′ and G″ for the sample with 5 wt % clay show an inverse dependence and lie between the modulus values of the samples with 1 and 2 wt % of clay. This is attributed to the alignment/orientation of nanoclay platelets in the intercalated nanocomposite induced by capillary extrusion. In the nonlinear regime, the nanocomposites show increased shear viscosities when compared with the neat resin. The dependence of the shear viscosity on clay loading has analogous trend to that of G′ and G″. Finally, a comparison has been made between the complex and steady viscosities to verify the applicability of the empirical Cox‐Merz rule. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 542–549, 2006     

Unperturbed dimension,interaction parameters,zeta potential and rheology of sodium alginate in binary solvent mixtures

The intrinsic viscosity [η] of sodium alginate having different molecular weights (high molecular weight (type A), medium molecular weight (type B) and low molecular weight (type C)) is measured at 293–303 K temperature in various mixtures of water (good solvent), acetone (ACE, poor solvent) and water-ethoxy ethanol (EE, poor solvent). The observed result particularly the Huggins constant (K _H) values shows a significant variation of cosolvency as a function of solvent composition (Φ_ACE/Φ_EE) and the temperature. Unperturbed dimensions (K _θ) under non-theta condition have been calculated using various equations in different water-acetone and water-ethoxy ethanol mixtures. The value of K _θ obtained from three different methods of measurements viz., Burchard-Stockmayer and Fixman (BSF), Berry and Inagaki-Suzuki-Kurata (ISK) agree well with each other except in a few compositions of solvents. The molecular extension factor (α _n) and actual end-to-end distance (α _n K _θ) have also been computed herein. Further, the shear thinning nature of the sodium alginate solutions (representative illustration: type A) in water and water-acetone mixed systems has been investigated at increasing strain rate. Results show that the viscous modulus G″ predominates over the elastic modulus G′ and the systems behave as viscoelastic fluids under present conditions. Higher value of G′ in acetone-water mixed solvent system compared to that in pure water undoubtedly indicates enhancement of the elasticity in alginate system in the presence of acetone. Finally, zeta potential measurement demonstrates that the polymeric surface of sodium alginate (representative illustration: type A) is essentially negatively charged and the zeta potential of the polymer is more responsive to the composition of ethoxy ethanol than that of acetone in the aqueous-organic mixed solvents.     

Rheological behavior of multiwalled carbon nanotube/polycarbonate composites

The rheological behavior of compression molded mixtures of polycarbonate containing between 0.5 and 15 wt% carbon nanotubes was investigated using oscillatory rheometry at 260 °C. The nanotubes have diameters between 10 and 15 nm and lengths ranging from 1 to 10 μm. The composites were obtained by diluting a masterbatch containing 15 wt% nanotubes using a twin-screw extruder. The increase in viscosity associated with the addition of nanotubes is much higher than viscosity changes reported for carbon nanofibers having larger diameters and for carbon black composites; this can be explained by the higher aspect ratio of the nanotubes. The viscosity increase is accompanied by an increase in the elastic melt properties, represented by the storage modulus G′, which is much higher than the increase in the loss modulus G″. The viscosity curves above 2 wt% nanotubes exhibit a larger decrease with frequency than samples containing lower nanotube loadings. Composites containing more than 2 wt% nanotubes exhibit non-Newtonian behavior at lower frequencies. A step increase at approximately 2 wt% nanotubes was observed in the viscosity-composition curves at low frequencies. This step change may be regarded as a rheological threshold. Ultimately, the rheological threshold coincides with the electrical conductivity percolation threshold which was found to be between 1 and 2 wt% nanotubes.     

Dynamic rheological properties of high‐density polyethylene/polystyrene blends extruded in the presence of ultrasonic oscillations

The linear rheological properties of high‐density polyethylene (HDPE), polystyrene (PS), and HDPE/PS (80/20) blends were used to characterize their structural development during extrusion in the presence of ultrasonic oscillations. The master curves of the storage shear modulus (G′) and loss shear modulus (G″) at 200°C for HDPE, PS, and HDPE/PS (80/20) blends were constructed with time–temperature superposition, and their zero shear viscosity was determined from Cole–Cole plots of the out‐of‐phase viscous component of the dynamic complex viscosity (η″) versus the dynamic shear viscosity. The experimental results showed that ultrasonic oscillations during extrusion reduced G′ and G″ as well as the zero shear viscosity of HDPE and PS because of their mechanochemical degradation in the presence of ultrasonic oscillations; this was confirmed by molecular weight measurements. Ultrasonic oscillations increased the slopes of log G′ versus log G″ for HDPE and PS in the low‐frequency terminal zone because of the increase in their molecular weight distributions. The slopes of log G′ versus log G″ for HDPE/PS (80/20) blends and an emulsion model were used to characterize the ultrasonic enhancement of the compatibility of the blends. The results showed that ultrasonic oscillations could reduce the interfacial tension and enhance the compatibility of the blends, and this was consistent with our previous work. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 3153–3158, 2004     

Dynamic viscoelastic behavior of triple helical Lentinan in water: Effects of concentration and molecular weight

The dynamic viscoelasitc behavior of Lentinan, one triple helical β-(1 → 3)-d-glucan from the fruiting body of Lentinus edodes, in water was investigated as a function of concentration and molecular weight at 25 °C by using dynamic rheology. It was revealed that the shear storage moduli (G′), viscous loss moduli (G″), and the dynamic complex viscosity (η^∗) exhibited strong dependence on concentration and molecular weight. At low concentrations, the Lentinan/water systems displayed liquid-like behavior with G′ lower than G″ at low frequencies and crossing-over at high frequencies. With increasing concentration, the elastic response of the Lentinan/water system was stronger than the viscous response, leading to the conclusion that the Lentinan/water systems displayed a predominantly solid-like behavior. The gel point (c_gel) was determined from Winter-Chambon method (frequency-independence of tan δ). The most important point is that the c_gel was much lower than some synthesized polymers and other flexible polysaccharides, which may be attributable to the high stiffness of triple helical Lentinan and strong intra- and intermolecular interactions among polysaccharide chains. Furthermore, a decrease in molecular weight leads to a sharp increase of c_gel. The dynamic strain sweep measurements proved that the gelation of Lentinan in water is induced by the extremely entangled and stiff triple helices forming continuous network, and the Lentinan gel is structurally more like a solution that is unable to flow within a timescale of usual observation.     

Non-Newtonian viscosity and non-linear flow birefringence of cellulose tricarbanilate

The shear rate dependence of the intrinsic viscosity and of the intrinsic property, which can be derived from the extinction angle, was investigated for a sample of cellulose tricarbanilate. Its number-average molecular weight was 4.4 × 10⁵; the solvents used were dioxane at 25°C and phenyl benzoate at 75°C, the latter being known to break most intramolecular hydrogen bonds. The onset of non-Newtonian viscosity was found at a reduced shear rate of about 0.1, whereas non-linear behaviour in the extinction angle was noticed already at 0.02. The obtained data were compared with the theory by Noda and Hearst¹⁰, which deals with the influence of chain stiffness on the viscoelastic properties of polymer solutions. The qualitative outcome of this theory agrees fairly well with the experimental results. However, the onset of non-linear behaviour, especially in the extinction angle, occurs at lower values of the reduced shear rate than predicted. The stress—optical law remains surprisingly valid for this stiff polymer throughout almost the whole accessible range of reduced shear rates. However, some experiments with the highly viscous solvent tri-o-cresyl phosphate at 30°C show appreciable deviations at reduced shear rates larger than 1.0.     

Dynamic rheological behavior and mechanical properties of PVC/ACS blends

In order to increase the processability and mechanical properties of poly(vinyl chloride) (PVC), the terpolymer of acrylonitrile-chlorinated polyethylene-styrene (ACS) is used to modify the PVC. The plasticizing, rheological, and dynamic mechanical properties of PVC/ACS blends are investigated by means of torque rheometer, oscillation rheometer, and dynamic mechanical analyzer. The measurements of torque rheometer showed that both plasticizing time and stabilization torque are decreased with increasing ACS content. The PVC/ACS melts displayed larger dynamic storage modulus (G′), loss modulus (G′′), and complex viscosity (η*) than that of pure PVC, and these values reached maximum for the blend with 10 wt% ACS. When ACS content was below 10 wt%, PVC and ACS showed good compatibility in the blends by displaying a single T _g; however, when ACS content was more than 15 wt%, the phase separation phenomena occurred in the blends. PVC/ACS blends showed larger storage modulus (E′) and loss modulus (E′′) than that of pure PVC, but these values decreased with increasing ACS content. ACS can enhance both tensile and impact strength of PVC, and the impact strength reached maximum with 15 wt% ACS content which is higher 2.5 kJ/m² than the pure PVC. These results suggested that ACS is an efficient processing aid and toughening modifier for PVC at appropriate content.     

Electro-rheological effect and dynamic rheological properties of a blend composed of two liquid crystalline materials with different molecular weight

Electro-rheological (ER) effect of a blend composed of two liquid crystalline materials with different molecular weights is described in this article. The results indicated that ER effect of the blend was observed at the temperature range where each neat sample did not show ER effect. Furthermore, both storage modulus (G′) and loss modulus (G″) decreased drastically at the temperature range for the blend in dynamic viscoelastic measurements. We show that steady ER effect could be obtained by using a blend made up of two liquid crystalline components, whereas remarkable increment in shear stress was not observed for each component under applied electric field.