On dry sliding friction and wear behaviour of PEEK and PEEK/SiC-composite coatings

In this work, polyetheretherketone (PEEK) and PEEK/SiC-composite coatings were deposited on Al substrates using a printing technique to improve their surfaces performance. The objective of this work was to investigate coatings friction and wear behaviour. Especially, the effect of sliding velocity and applied load on coatings friction coefficient and wear rate was evaluated in range of 0.2-1.4 m/s and 1-9 N, respectively. Compared to Al substrate, the coated samples exhibit excellent friction coefficient and wear rate. For PEEK coating, under an applied load of 1 N, the increase in sliding velocity can result in decreasing of friction coefficient at a cost of wear resistance. Under a load of 9 N, however, PEEK coating exhibits the highest friction coefficient and wear rate at an intermediate velocity. These influences appear to be mainly ascribed to the influence of contact temperature of the two relative sliding parts. In most test conditions, the composite coating exhibits better wear resistance and a little higher friction coefficient. SiC reinforcement in composite coating plays a combined role. First of all, it might lead to energy dissipation for activation of fracture occurred on the interface of PEEK and the powders. Moreover, it can reduce coating ploughs and the adhesion between the two relative sliding parts.     

Laboratory evaluation of anti‐fretting lubricants

To characterise the friction and wear behaviour of materials and lubricants under a variety of operating conditions, laboratory models are frequently used to provide useful information. For example, during the development and/or selection of tribomaterials and lubricants, laboratory ranking of candidate products can save many hours of field testing. A reciprocating ball‐on‐flat wear test rig has been developed to rank the performance of materials, surface coatings, and lubricants under boundary, extreme‐pressure, or fretting conditions in a variety of environments and at various temperatures. The rig design is based on ASTM G133–1995. The friction force and wear are measured on both specimens while the load, stroke length and frequency, test temperature, lubricant type, test duration, surface topography of both ball and flat specimens, specimen materials, and environmental conditions are noted. The results presented in this paper refer specifically to a series of tests performed to evaluate various anti‐fretting lubricants. Two lubricants are compared in terms of friction coefficient and wear volume over time. A clear difference is shown between the two products.     

The influence of surface roughness on friction and wear of machine element coatings

The use of low friction coatings like amorphous carbon or metal-doped carbon coatings on machine elements is constantly increasing. Most often, a surface treatment, e.g. grinding and polishing or honing, is required for optimal performance of the coated machine element. This can be time consuming and costly.In this study, the effect of surface roughness on friction and sliding wear of two different coatings, one tungsten containing and one chromium containing coating, were examined using a ball-on-disc test. Ball bearing steel plates were grinded to different surface roughnesses and coated with the two different coatings.The friction was found to depend on surface roughness where the rougher surfaces gave higher friction coefficients. The wear rate for the a-C:W coating was found to be independent of the roughness, whereas the roughness had a strong influence on the wear rate for the a-C:Cr coating. This could partly be explained by a difference in wear mechanism, where fatigue wear was observed for the a-C:Cr coating but not for the a-C:W coating.     

Combination of DLC coatings and EP additives for improved tribological behaviour of boundary lubricated surfaces

The aim of the present investigation was to obtain some further understanding of the mechanism responsible for low-friction behaviour of W-containing DLC coatings (W-DLC) when lubricated with EP additivated oil. Boundary lubricated wear and friction tests were performed under reciprocating sliding motion using a high frequency test rig and a contact pressure of 1.5 GPa. Additionally, some of the tests were performed in a load-scanning reciprocating test rig, with the contact pressure being in the range from 2.4 to 5.6 GPa. The influence of concentration of a sulphur-based EP additive on the friction behaviour was investigated.This investigation showed that W-DLC coatings greatly improve the tribological properties of boundary-lubricated surfaces, especially when pairing coated and uncoated steel surfaces. The improved tribological behaviour was found to be governed by the gradual formation of a WS₂ type tribofilm on the steel counter-face or on revealed steel substrate. The friction level depends on the additive concentration.     

Friction and wear behaviors of MoS2/Zr coated HSS in sliding wear and in drilling processes

MoS2 metal composite coatings have been successful used in dry turning, but its suitability for dry drilling has not been yet established. Therefore, it is necessary to study the friction and wear behaviors of MoS2/Zr coated HSS in sliding wear and in drilling processes. In the present study, MoS2/Zr composite coatings are deposited on the surface of W6Mo5Cr4V2 high speed steel(HSS). Microstructural and fundamental properties of these coatings are examined. Ball-on-disc sliding wear tests on the coated discs are carried out, and the drilling performance of the coated drills is tested. Test results show that the MoS2/Zr composite coatings exhibit decreases friction coefficient to that of the uncoated HSS in sliding wear tests. Energy dispersive X-ray(EDX) analysis on the wear surface indicates that there is a transfer layer formed on the counterpart ball during sliding wear processes, which contributes to the decreasing of the friction coefficient between the sliding couple. Drilling tests indicate that the MoS2/Zr coated drills show better cutting performance compared to the uncoated HSS drills, coating delamination and abrasive are found to be the main flank and rake wear mode of the coated drills. The proposed research founds the base of the application of MoS2 metal composite coatings on dry drilling.     

Functional behaviour of PVD coatings under sliding and rolling stress conditions

Whereas wear-resistant PVD coatings are well established in the field of metalcutting, and the functional and tribological behaviour of these coatings is well known under such conditions, PVD coatings are used only occasionally in mechanical engineering. The reason for this seems to be the lack of information concerning the functional behaviour of these coatings in closed tribosystems. To evaluate new areas of application together with optimised coating compounds, model wear tests were performed under sliding, rolling and slip-rolling stress conditions. In addition, the test parameters, such as sliding speed, load, ambient temperature, and number of revolutions were varied, as were the coating compounds and their thicknesses. The results obtained show that friction and wear of PVD coatings are both strongly influenced by the kind of stress and the test parameters themselves. Coatings that perform well under certain test conditions can break down quickly under some other stress conditions. TiN coatings, for example, which display low friction and wear under sliding friction, fail under rolling conditions very shortly afterwards.     

粉末涂料固体润滑膜滚动/滑动复合干摩擦磨损特性研究

在M-2000磨损试验机上考察了经过一次处理和经两次处理的40Cr钢环表面喷涂3种粉末涂料型固体润滑膜(P型、H型、E型)试样,在线载荷为104N/m、相对滑动速度为0.042 m/s、干摩擦滚动/滑动复合磨损条件下的摩擦磨损性能,通过扫描电子显微镜(SEM)对试样磨损表面以及磨屑进行了显微观察。结果表明:底材经过一次处理(化学底膜处理)的复合固体润滑膜试样,P型和E型在磨损后期的摩擦因数分别稳定在0.38和0.32,而H型在0.40左右跳动;P型和H型的涂层磨损脱落期为60 m in左右,E型为120 m in左右;质量磨损从小到大顺序为P型相似文献   

Tribological testing of some potential PVD and CVD coatings for steel wire drawing dies

The aim of this study was to investigate the possibility to replace cemented carbide wire drawing dies with CVD or PVD coated steel dies. Material pick-up tendency, friction and wear characteristics of four different commercial coatings – CVD TiC and PVD (Ti,Al)N, CrN and CrC/C – in sliding contact with ASTM 52100 bearing steel were evaluated using pin-on-disc testing. The load bearing capacity of the coating/substrate composites was evaluated using scratch testing. The results show that the friction characteristics and material pick-up tendency of the coatings to a large extent is controlled by the surface topography of the as-deposited coatings which should be improved by a polishing post-treatment in order to obtain a smooth surface. Based on the results obtained in this study, three different coatings – CrC/C, TiC and dual-layer TiC/CrC/C – are recommended to be evaluated in wire drawing field tests. CrC/C and TiC are recommended due to their intrinsic low friction properties and material pick-up tendency in sliding contact with steel. The dual-layer is recommended in order to combine the good properties of the two coatings CrC/C (low shear strength) and TiC (high hardness).     

Tribological Properties of DLC Coatings in Helium

The aim of this research work was to investigate tribological properties of low-friction DLC coatings when operating in helium atmosphere. Two commercial DLC coatings (a-C:H and Me-C:H) were included in the investigation and compared to reference PTFE-based coatings, normally used on components operating in helium. Coatings were deposited on hardened 100Cr6 bearing steel discs and tested against uncoated steel balls in low-load pin-on-disc contact configuration. Investigation was focused on the effect of substrate roughness (R _a ?=?0.05?C0.2???m) and contact conditions, including contact pressure (150?C350?MPa) and sliding speed (0.2?C0.4?m/s) on the coefficient of friction of DLC coatings operating in helium. Results of this investigation show that for low-load sliding contact DLC coatings provide low friction in helium atmosphere, similar to soft PTFE-based coatings. At the same time DLC coatings investigated were found to substantially reduce wear of the coated surface. However, while the wear of the coated part has been more or less eliminated, application of DLC coating prolongs running-in and increases wear of the steel counter-part. Furthermore, also in helium atmosphere tribolgical behaviour of DLC coatings showed dependence on the coating type and contact conditions.     

Friction and wear behaviour of hard coatings in vibrating contacts

The friction and wear behaviour of thin hard coatings, such as TiN and the promising class of C-based coatings (a-C, a-C:H, and diamond for example), are compared under oscillating and reciprocating sliding conditions. The typical effects of test parameters, such as stroke, frequency, normal force, relative humidity and test duration, are described as a basis for the proper selection of test conditions or, conversely, for the selection of suitable coatings for particular practical applications. Friction and wear data from over 1000 vibrating tests using thin hard coatings against 100Cr6 and against Al₂O₃ have been compiled in a database. This allows easy manipulation and comparison of test results. Using selection criteria and filter procedures (e. g., lifetime of coatings, friction limits, and critical wear rate), suitable coating systems for different test conditions can be chosen from the database. The effects of test parameters on friction and wear behaviour and changes have anyway to be known for meaningful tribotesting, as well as for the selection of coatings.     

Wear Characteristics of Traditional Manganese Phosphate and Composite hBN Coatings

In this study, the tribological properties of traditional manganese phosphate coatings and composite hBN coatings

composed of nano-hexagonal boron nitride (hBN) in layered manganese phosphate crystals on AISI 1040 steel were investigated. Wear tests were carried out under controlled temperature and humidity using ball-on-disc tribometers for samples that were either submerged in oil or retaining oil on their surfaces at a sliding speed of 2.5 cm/s with loads of 1, 3, 5, and 10 N and sliding distances of 40, 80, 100, and 120 m. The surface profiles before and after the tests were used to characterize the wear. The surfaces of the coated samples were examined using scanning electron microscopy (SEM). The coefficients of friction and wear rates of the coated samples were also measured. The average wear rates of the composite hBN-coated samples were significantly lower than those of the traditional manganese phosphate–coated samples for each of the loading conditions for the oil submersion and retained oil tests. The coefficient of friction (COF) values for the traditional manganese phosphate–coated samples did not change significantly with increasing load. The COF values for the composite hBN coated–samples decreased with increasing load in the oil submersion test.     

On the influence of surface finish of SSiC on the results of tribological laboratory tests in the case of water lubricated oscillating sliding

The development of materials for tribological applications requires characterisation of their friction and wear behaviour. This characterisation is often based on tribological model testing, working with simple shaped specimens, running under well-defined conditions. Discrepancies in test results may arise from the fact that non-standard tests with different sets of operational parameters are used. An essential starting point for the development of tribological standards is knowledge of the main parameters that influence the tribological properties. One aspect that is not often adequately taken into account is the surface finish of the test specimens. Results are presented of friction and wear tests with self-mated SSiC couples (ball on disc), running in water in an oscillating sliding mode. The surfaces of the disc were ground, lapped, or polished, respectively, running against a polished ball. For certain test conditions, the influence of the surface finish on wear is found to be negligible, while for other conditions, the wear rate can differ by one order of magnitude or even more. The consequences for the standardisation of wear tests of ceramic materials are discussed.     

Friction and wear behaviour of low-friction coatings in conventional and alternative fuels

Today low-friction PVD coatings are used regularly in combustion engines to reduce wear and energy loss due to friction. Three coatings based on transition-metal dichalcogenides and three DLC coatings were tested with respect to tribological behaviour in non-conformal sliding contact, in five conventional and alternative fuels and fuel blending components. The friction and wear proved to vary substantially between the different tested systems. The DLC coatings exhibited extremely good wear properties, but also higher friction. Contrastingly the TMD coatings showed promising friction results, but in their present forms they do not offer sufficient wear resistance in the tested severe contact situation.     

Influence of surface texture on boundary lubricated sliding contacts

The friction and wear behaviour of boundary lubricated sliding surfaces is influenced by the surface texture. By introducing controlled depressions and undulations in an otherwise flat surface, the tribological properties can be improved. Lubricant can then be supplied even inside the contact by the small reservoirs, resulting in a reduced friction and a prolonged lifetime of the tribological contact.In the present paper, well-defined surface textures were produced by lithography and anisotropic etching of silicon wafers. The wafers were subsequently PVD coated with thin wear resistant TiN or DLC coatings, retaining the substrate texture. The size and shape of the depressions were varied and evaluated in reciprocating sliding under dry and boundary lubricated conditions.     

Friction and wear properties of Fe7Mo6-based alloy in ethyl alcohol

In this study, the friction and wear properties of Fe₇Mo₆-based alloy, Fe and Mo disk specimens sliding against ASTM 52100 steel and Cu and SiC ball (or pin) specimens in ethyl alcohol were evaluated using an Optimol SRV oscillating friction and wear tester. The Fe₇Mo₆-based alloy disk specimens exhibited more stable friction coefficients than the Fe and Mo disk specimens when slid against the ASTM 52100 steel ball specimen. On the other hand, the Fe/SiC tribo-pairs exhibited the lowest average friction coefficients (0.14-0.17).     

Comparative Study of Thermally Sprayed Coatings Under Different Types of Wear Conditions for Hard Chromium Replacement

The tribological properties of part surfaces, namely their wear resistance and friction properties, are decisive in many cases for their proper function. To improve surface properties, it is possible to create hard, wear-resistant coatings by thermal spray technologies. With these versatile coating preparation technologies, part lifetime, reliability, and safety can be improved. In this study, the tribological properties of the HVOF-sprayed coatings WC–17%Co, WC–10%Co4%Cr, WC–15% NiMoCrFeCo, Cr₃C₂–25%NiCr, (Ti,Mo)(C,N)–37%NiCo, NiCrSiB, and AISI 316L and the plasma-sprayed Cr₂O₃ coating were compared with the properties of electrolytic hard chrome and surface-hardened steel. Four different wear behavior tests were performed; the abrasive wear performance of the coatings was assessed using a dry sand/rubber wheel test according to ASTM G-65 and a wet slurry abrasion test according to ASTM G-75, the sliding wear behavior was evaluated by pin-on-disk testing according to ASTM G-99, and the erosion wear resistance was measured for three impact angles. In all tests, the HVOF-sprayed hardmetal coatings exhibited superior properties and can be recommended as a replacement for traditional surface treatments. Due to its tendency to exhibit brittle cracking, the plasma-sprayed ceramic coating Cr₂O₃ can only be recommended for purely abrasive wear conditions. The tested HVOF-sprayed metallic coatings, NiCrSiB and AISI 316L, did not have sufficient wear resistance compared with that of traditional surface treatment and should not be used under more demanding conditions. Based on the obtained data, the application possibilities and limitations of the reported coatings were determined.     

Role of the Transfer Film on the Friction and Wear of Metal Carbide Reinforced Amorphous Carbon Coatings During Run-in

The relationship between friction, wear, and transfer films of three metal carbide-reinforced amorphous carbon coatings (TiC/a:C, TiC/a:C–H, and WC/a:C–H), sometimes referred to as metal-doped diamond-like carbon coatings, has been investigated. Tribological tests were performed in an in situ tribometer with sapphire or steel hemispheres run against coated flats in dry or ambient air. The sliding contact interface was observed and recorded by optical microscopy during reciprocating sliding tests. The friction and wear behavior during run-in depended on the number of sliding cycles to form a stationary transfer film on the hemisphere. Stationary transfer films formed rapidly (within ten cycles) and the friction coefficient fell to 0.2 (ambient air) or 0.1 (dry air), except with sapphire against WC/a:C–H in dry air; with the latter, a stationary transfer film required nearly 100 cycles to form, during which the friction remained high and the wear rate was from 10 to 100 times higher than the other two coatings. For all coatings, three velocity accommodation modes (VAM) were observed from run-in to steady-state sliding and were correlated with the friction and wear behavior. The delayed adherence of the transfer film to sapphire from WC/a:C–H coatings in dry air is discussed in terms of equilibrium thermochemistry. Friction and wear behavior during run-in, therefore, depended on transfer film adherence to the hemisphere and the VAM between transfer films and the coating.     

Friction and wear measurements of laser-sintered and coated parts

The aim of this research is the investigation of surface properties, the measurements of friction coefficient and wear rate of laser-sintered and coated parts. The industrial background of this research is to prove applicability of laser-sintered prototype tools for injection moulding of fibre-reinforced polymers, furthermore to increase the wear resistance of unalloyed steel tools by laser coatings. The materials of the test specimens were laser-sintered phosphorous bronze and unalloyed steel. For increase of wear resistance we used hard Co-based and glassy-like Fe-based (FeB) coatings. As counter bodies we used polymers reinforced with short carbon and glass fibres. The laboratory model tests of selective laser-sintered parts were carried out on a pin-on-disk machine. In case of coated parts—with higher wear resistance—we used a cylinder-on-cylinder tribometer. The tribological properties were determined at different load and temperature conditions. The results of the investigation show that the friction coefficient and wear resistance of laser treated surfaces are good. The coefficient of friction of coated specimens is slightly less, but the wear rate is significantly less.     

Tribological Properties of SiC-Reinforced Basalt-Based Coatings

In the current study, the wear behaviour of basalt-based glass and glass–ceramic coatings was investigated. SiC-reinforced basalt-based powders were coated by an atmospheric plasma spray process and evaluated using the ball-on-disk wear test. X-ray diffraction analysis, scanning electron microscopy, and optical microscopy were employed for characterisation. The friction coefficients of the basalt-based glass and glass–ceramic coatings ranged from 0.38 to 0.55 and from 0.12 to 0.70, respectively, depending on the wear condition and SiC content. The wear test results show that SiC addition has a positive effect on the wear resistance of the glass and glass–ceramic coatings.     

Friction and Wear Behavior of WS2/Zr Self-lubricating Soft Coatings in Dry Sliding Against 40Cr-Hardened Steel Balls

WS₂ and WS₂/Zr self-lubricating soft coatings were produced by medium-frequency magnetron sputtering, multi-arc ion plating and ion-beam-assisted deposition technique on the cemented carbide YT15 (WC + 15 % TiC + 6 % Co) substrates. Microstructural and fundamental properties of these coatings were examined. Sliding wear tests against 40Cr-hardened steel using a ball-on-disk tribometer method were carried out with these coated materials. The friction coefficient and wear rates were measured with various applied loads and sliding speeds. The wear surface features of the coatings were examined using SEM. The results showed that the WS-1 specimen (with WS₂/Zr composite coating) has higher hardness and coating/substrate critical load compared with that of the WS-2 specimen (only with WS₂ coating). The friction coefficient of WS-1 specimen increases with the increase in applied load and is quite insensitive to the sliding speed. The wear rate of the WS-1 specimen is almost constant under different applied loads and sliding speeds. The WS-1 specimen shows the smallest friction coefficient and wear rate among all the specimens tested under the same conditions. The WS-1 specimen exhibits improved friction behavior to that of the WS-2 specimen, and the antiwear lifetime of the WS₂ coatings can be prolonged through adding Zr additives. The self-lubricating and wear mechanism of the WS₂/Zr coating was also found from the sliding wear tests.