Effect of Temperature on the Dry Sliding Friction and Wear of Rice Bran Ceramics against Different Counterpart Materials

In this study, we investigated the effect of temperature on the friction and wear of rice bran (RB) ceramics, a hard porous carbon material made from rice bran, sliding against alumina, stainless steel, and bearing steel balls under dry conditions. Friction tests were performed using a ball-on-disk-type friction tester wherein a ceramic heater was installed in the rotational stage. The surface temperature of the RB ceramic disk specimens was controlled at 20, 100, 150, or 200°C. The normal load was 1.96 N, sliding velocity was 0.1 m/s, and number of cycles was 20,000. The effect of surface temperature on the friction and wear of RB ceramics substantially differed among the ball material types. The friction coefficient for the RB ceramics sliding against an alumina ball decreased with increasing temperature and exhibited an extremely low value (0.045) at 200°C. The friction coefficient in the case of the RB ceramics sliding against a stainless steel ball exhibited a stable value as the temperature was increased to 150°C and slightly decreased as the temperature was increased further, reaching a low value of 0.122 at 200°C. The friction coefficient for the RB ceramics sliding against bearing steel ball drastically increased with increasing temperature, reaching 0.381 at 200°C. The specific wear rate of the RB ceramics increased with increasing temperature; it was lowest when sliding against alumina and highest when sliding against bearing steel. The wear of the alumina ball was the lowest and that of the bearing steel ball was the highest under all investigated temperature conditions. On the basis of these results, we concluded that alumina is a promising counterpart material for RB ceramics sliding at high temperatures (≤200°C).     

The tribological characteristics of TiCN coating at elevated temperatures

The tribological behaviour of TiCN coating prepared by unbalanced magnetron sputtering is studied in this work. The substrates made from austenitic steel were coated by TiCN coatings during one deposition. The measurements were provided by high temperature tribometer (pin-on-disc, CSM Instruments) allowing measuring the dependency of friction coefficient on cycles (sliding distance) up to 500 °C. The evolution of the friction coefficient with the cycles was measured under different conditions, such as temperature or sliding speed and the wear rate of the ball and coating were evaluated. The 100Cr6 balls and the Si₃N₄ ceramic balls were used as counter-parts. The former were used at temperatures up to 200 °C, the latter up to 500 °C. The wear tracks were examined by optical methods and SEM. The surface oxidation at elevated temperatures and profile elements composition of the wear track were also measured.The experiments have shown considerable dependency of TiCN tribological parameters on temperature. Rise in temperature increased both friction coefficient and the wear rate of the coating in case of 100Cr6 balls. The main wear mechanism was a mild wear at temperatures up to 200 °C; fracture and delamination were dominating wear mechanisms at temperatures from 300 to 500 °C.     

Effects of Contact Pressure and Sliding Speed on the Unlubricated Friction and Wear Properties of Zn-15Al-3Cu-1Si Alloy

The unlubricated friction and wear properties of Zn-15Al-3Cu-1Si alloy were studied over a range of contact pressure (1–5 MPa) and sliding speed (0.5–2.5 ms^?1) for a sliding distance of 2,500 m using a block-on-disc type test machine. It was observed that as the contact pressure increased, the friction coefficient of the alloy decreased but its working temperature, surface roughness, and wear volume increased. Sliding speed had no significant effect on the friction coefficient of the alloy but increased its working temperature, surface roughness, and wear volume. It was also observed that the formation of a hard and brittle surface layer had a great influence on the wear behavior of the experimental alloy. The hardness and thickness of this layer increased with increasing contact pressure and sliding speed. However, contact pressure was found to be much more effective on the hardness of the surface layer of this alloy. Both adhesion and abrasion were observed to be the dominant wear mechanisms for the alloy under the given sliding conditions. The results obtained from the friction and wear tests are discussed in terms of the test conditions and microstructural changes that take place during sliding.     

Ionic Liquids as Lubricants of Titanium–Steel Contact. Part 2: Friction, Wear and Surface Interactions at High Temperature

The tribological behaviour and surface interactions of titanium sliding against AISI 52100 steel have been studied at 200 and 300 °C in the presence of two commercial imidazolium room temperature ionic liquid (ILs): 1-octyl-3-methylimidazolium tetrafluoroborate (L108) and 1-hexyl-3-methylimidazolium hexafluorophosphate (LP106). L108 presents the higher thermal stability but gives higher friction coefficients and wear rates than LP106, with long running-in periods and high friction values, both at 200 and 300 °C. Friction and wear rates for LP106 are lower and decrease as the temperature increases from 25 to 200 °C. At 200 °C, LP106 shows a constant friction coefficient, without running-in, produces a mild wear on titanium and no surface damage on steel. LP106 fails at 300 °C, close to its degradation temperature, due to tribochemical decomposition through partial dissociation of the hexafluorophosphate anion, with formation of a phosphorus-rich layer on the steel ball, while the titanium wear track surface is heterogeneous, showing regions with the presence of fluoride and others with the presence of phosphate. When the steel ball is substituted for a ruby sphere under the same conditions at 300 °C, a low friction coefficient and mild wear is observed, due to the higher stability of the LP106 lubricant at the ruby–titanium interface. The friction coefficients, wear mechanisms and surface interactions have been studied by means of friction-distance records, SEM, EDX and XPS.     

Effect of temperature on friction and wear of prehardened tool steel during sliding against 22MnB5 steel

Abstract

Mechanical components in tribological systems exposed to elevated temperatures are gaining increased attention since more and more systems are designed to operate under extreme conditions. In hot metal forming, the effect of temperature on friction and wear is especially important since it is directly related to process economy (tool wear) and quality of the produced parts (friction between tool and workpiece). This study is therefore focused on fundamental understanding pertaining to the tribological characteristics of prehardened hot work tool steel during sliding against 22MnB5 boron steel. The tribological tests were carried out using a high temperature reciprocating sliding friction and wear tester under a normal load of 31 N (corresponding to a contact pressure of 10 MPa), a sliding speed of 0·2 m s^?1 and temperatures ranging from 40°C to 800°C. It was found that friction coefficient and specific wear rate decreased at elevated temperature because of formation of compacted wear debris layers on the surfaces.     

Tribo-oxidation of Self-mated Ti3SiC2 at Elevated Temperatures and Low Speed

The tribological behavior of self-mated Ti₃SiC₂ is investigated from ambient temperature to 800?°C at a sliding speed of 0.01?m/s in air. The results show that at the temperatures lower than 300?°C, friction coefficient and wear rates are as high as 0.95 and 10^?3?mm³/N?m, respectively. With the temperature increasing to 600?°C, both the friction coefficient and wear rates show consecutive decrease. At 700 and 800?°C, friction coefficient and wear rates are 0.5 and 10^?6 mm³/N?m, respectively. According to the wear mechanism, the tribological behavior of Ti₃SiC₂ can be divided into three regimes: mechanical wear-dominated regime from ambient temperature to 300?°C characterized by pullout of grains; mixed wear regime (mechanical wear and oxidation wear) from 400 to 600?°C; and tribo-oxidation-dominated wear regime above 700?°C. The tribo-oxides on the worn surfaces involve oxides of Si and Ti. And, species transformation occurs to these two oxides with the increasing temperature. In the competition oxidation of elements Ti and Si, Si is preferably oxidized because of its high active position in the crystal structure. Additionally, plastic flow is another notable characteristic for the tribological behavior of self-mated Ti₃SiC₂.     

Dry Sliding Friction and Wear Characteristics of Cu-Sn Alloy Containing Molybdenum Disulfide

The wear and sliding friction response of a hybrid copper metal matrix composite reinforced with 10 wt% of tin (Sn) and soft solid lubricant (1, 5, and 7 wt% of MoS₂) fabricated by a powder metallurgy route was investigated. The influence of the percentages of reinforcement, load, sliding speed, and sliding distance on both the wear and friction coefficient were studied. The wear test with an experimental plan of six loads (5–30 N) and five sliding speeds (0.5–2.5 m/s) was conducted on a pin-on-disc machine to record loss in mass due to wear for two total sliding distances of 1,000 and 2,000 m. The results showed that the specific wear rate of the composites increased at room temperature with sliding distance and decreased with load. The wear resistance of the hybrid composite containing 7 wt% MoS₂ was superior to that of the other composites. It was also observed that the specific wear rates of the composites decreased with the addition of MoS₂. The 7 wt% MoS₂ composites exhibited a very low coefficient of friction of 0.35. The hardness of the composite increased as the weight percentage of MoS₂ increased. The wear and friction coefficient were mainly influenced by both the percentage of reinforcement and the load applied. Wear morphology was also studied using scanning electron microscopy and energy-dispersive X-ray analysis.     

Tribological Properties of Graphite-Fiber-Reinforced,Partially Fluorinated Polyimide Composites

Graphite-fiber-reinforced polyimide (GFRPI) composites were formulated form three new partially fluorinated polyimides and three types of graphite fiber. Nine composites were molded into pins and evaluated in a pin-on-disk tribometer. Friction coefficients, wear rates, pin wear surface morphology, and transfer film formation were assessed at 25 and 300°C. Also assessed was the effect of sliding distance on friction and the effect of constantly increasing or decreasing temperature on friction. Wear was up to two orders of magnitude lower at 25°C and up to one order of magnitude lower at 300°C than with previously formulated NASA GFRPI composites.     

Effects of Aging Treatments on the High-Temperature Wear Behavior of 60Nitinol Alloy

This study was undertaken to investigate the effect of heat treatments on the high-temperature wear behavior of 60Nitinol. The samples were hot-worked, aged at two temperatures of 400 and 700°C for 1 h and then water quenched. The microstructure of the alloys was investigated by scanning electron microscopy and X-ray diffraction. Sliding wear tests were performed at two temperatures of 25 and 200°C using three types of 60Nitinol disks: hot-worked, aged at 400°C, and aged at 700°C. All wear tests were performed at a speed of 0.3 m/s under a normal load of 60 N for a total sliding distance of 1,000 m using WC-Co pins sliding against 60Nitinol disks. The worn surfaces and microstructure of the subsurfaces were studied by scanning electron microscopy. Compression and hardness tests were also performed to characterize the mechanical properties of the alloys. The highest fracture strain and lowest hardness were obtained for the sample aged at 700°C that contained Ni₃Ti₂ precipitants. This sample also showed the maximum wear resistance at a wear testing temperature of 200°C. This was attributed to the formation of a more compact and stable tribological layer on the worn surface of the softer sample.     

Microstructural,Mechanical, and Tribological Properties of Rice Husk–Based Carbon: Effect of Carbonizing Temperature

In this study, we investigated the microstructural, mechanical, and tribological properties of rice husk (RH)-based carbon carbonized at various carbonizing temperatures under dry conditions. All samples exhibited amorphous carbon structures and the X-ray diffraction spectra of the samples carbonized at 1300 and 1400?°C indicated the presence of a polymorphic crystals of silica. The hardness increased with temperature due to the densification of the structure and the presence of the hard crystalline silica. At low normal loads, the mean friction coefficient of the material decreased as the carbonizing temperature was increased from 600 to 800?°C and slightly decreased as the carbonizing temperature was further increased from 800 to 1400?°C. At the highest load, all samples, except for that carbonized at 600?°C, exhibited extremely low friction coefficients (around 0.05). The wear rates of the all samples were smaller than 10^?5 mm³/N·m, indicating that RH carbon exhibits sufficient wear resistance. A Raman spectroscopic analysis of the worn surface of a steel ball revealed that the transfer layer at 600?°C had a less graphitic structure compared to the other carbonizing temperature. Based on these findings, we recommend an optimal carbonizing temperature for applications of sliding materials exposed to dry sliding contact.     

Investigation of the Transition State in the Wear of Polyphenylene Sulfide Sliding Against Steel

The effect of sliding variables, including counterface roughness, sliding speed, and contact pressure, on the run-in state of wear and friction was studied. Sliding was performed in the pin-on-disk configuration with a polyphenylene sulfide (PPS) pin resting on the flat steel counterface. Some experiments were also run to study the effect of air cooling and heating. Optical microscopy and scanning electron microscopy were used to study the shape and size of the wear debris, worn pin surface, and the transfer film formed on steel counterfaces. It was found that friction and wear in the run-in state were significantly affected by the sliding variables studied and their influence was closely related to the development of a transfer film during the run-in state. If the transfer film developed during initial sliding, the coefficient of friction increased and wear rate decreased. The wear rate in the run-in state increased with the increase in initial counterface roughness and there was an optimal counterface roughness of 0.06 m Ra for minimum steady state wear rate. A higher applied load led to a higher wear rate in the run-in state but that was not the case with steady state wear rate.     

Effect of molybdenum disulphide upon the friction and wear in ceramic–steel pair

Friction and wear tests between a stationary block and a rotating ring under lubrication with molybdenum disulphide (MoS₂) were carried out at room temperature at a sliding distance of 500 m. Silicon nitride and cemented carbide blocks were pressed against a bearing steel ring, silicon nitride-bearing steel and cemented carbide-bearing steel pairs, by a load of 1600 N. The effect of molybdenum disulphide upon the coefficient of friction and the wear of the steel ring was discussed for both pairs in comparison with mineral oil lubricants. Molybdenum disulphide was more effective in reducing the coefficient of friction and the wear of the ring than the oil lubricants. Various mechanical pretreatment for forming MoS₂ film on the ring surface prior to the sliding tests were also considered. The mechanical pretreatment enabled the sliding test with the low friction coefficient even without lubrication over the sliding distance of 500 m. In general, the coefficient of friction and wear loss of the steel ring were smaller in the silicon nitride-bearing steel pair than in the cemented carbide-bearing steel pair.     

载流条件下铬青铜/3D碳/碳复合材料摩擦副的摩擦磨损性能

以3D碳/碳复合材料为销试样、铬青铜QCr0.5为盘试样进行了载流条件下的干滑动摩擦磨损试验。通过对有、无电流条件下销试样磨损量大小和摩擦因数影响度的比较,以及对销试样摩擦表面进行的微观形貌分析,结果表明,电流对铬青铜/3D碳/碳复合材料摩擦副的干摩擦行为具有显著的影响,并且由于电场、摩擦热、电弧热的共同作用,在销试样表层发生了磨粒磨损和氧化磨损。     

The use of post‐mortem Raman spectroscopy in explaining friction and wear behaviour of sintered polyimide at high temperature

Due to their thermal stability and high strength, polyimides are an aromatic type of polymer that is used in sliding equipment functioning under high loads and elevated temperature. However, its tribological behaviour under high temperature and atmospheric conditions is not fully understood. It has been reported that a transition from high towards lower friction occurs ‘somewhere’ in the temperature region between 100°C and 200°C; however, a correlation with changes in the polyimide molecular structure remains difficult to illustrate and it is not certain whether or not this transition is correlated to lower wear. In the present work sliding experiments under controlled bulk temperatures between 100°C and 260°C are performed. A transition is observed in both friction and wear at 180°C which is further explained by microscopic analysis of the transfer film on the steel counterface and Raman spectroscopy of the worn polymer surfaces. A close examination of the spectra reveals transitions in relative intensity of certain absorption bands, pointing to different orientation effects of the molecular conformation at the polymer sliding surface at 180°C. Copyright © 2006 John Wiley & Sons, Ltd.     

SiCp增强铝基复合材料与芳纶纤维增强摩擦材料摩擦副摩擦学特性与模型研究

对 Si Cp含量为 2 0 % (vol% )的铝基复合材料和芳纶纤维增强摩擦材料组成的摩擦副在干摩擦条件下的摩擦学特性进行了试验研究。试验表明 :摩擦副的摩擦系数受 Kevlar增强摩擦材料的热分解温度所控制 ,当温度低于2 0 0℃时 ,摩擦系数随滑动速度和温度增大而增大 ,并处于较高水平 ;当温度高于 2 0 0℃时 ,摩擦材料发生热分解 ,摩擦系数急剧下降到较低水平。摩擦材料具有磨损量和磨损率随滑动速度增加而减小的明显特征 ,摩擦副具有良好的耐磨性。建立了描述该摩擦副摩擦特性的数学模型。并用其解释了实验中的摩擦学现象。     

Influence of Combined Addition of Boron and Strontium on High-Temperature Wear Behavior of A356 Alloy

In the present study, the effect of the combined addition of boron (B) and strontium (Sr) on the high-temperature dry sliding wear behavior of A356 alloy has been investigated using a pin-on-disc wear testing machine attached with a furnace. During wear studies, the effect of alloy composition, normal pressure, sliding speed, and sliding distance on A356 alloy at four temperatures, namely, room temperature and 100, 200, and 300°C, have been investigated. Further, the cast alloys and worn surfaces of A356 alloy with and without B and Sr were characterized by scanning electron microscopy (SEM)/energy-dispersive spectroscopy (EDS) microanalysis. Results indicate that the combined addition of B and Sr to A356 alloy has led to improvements in wear properties. This is due to a change in microstructure, improvement in mechanical properties, and the formation of an oxide layer between the mating surfaces during the sliding wear process.     

Oscillating sliding wear behaviour of SiC,TiC, TiB2, 59SiC–41TiB2 and 52SiC–24TiC–24TiB2 materials up to 750°C in air

The tribological behaviour of different monolithic and composite ceramics was evaluated in the temperature range between room temperature and 750°C. The test method was oscillating sliding with a ball‐on‐disk arrangement in an SRV machine. Alumina balls were used as counter body. The friction behaviour was determined on‐line, and the wear behaviour was determined from calculations on the basis of wear scar dimensions and profilometric measurements. The friction depends on temperature and shows an increase for most materials for increasing temperature; the smallest friction at all temperatures is found for monolithic TiC. The wear behaviour shows different trends for the different materials. In tests against SiC a maximum of wear is found at 500°C, for TiC at 200°C and for TiB₂ at 750°C. The composite ceramics suffer the smallest wear of all materials in the range from 200°C to 500°C. Copyright © 2006 John Wiley & Sons, Ltd.     

Wear and Friction Characteristics of a Selected Stainless Steel

Dry sliding wear tests were performed for 3Cr13 steel with various tempered states at 25–400°C; wear and friction characteristics as well as the wear mechanism were explored. With an increase in test temperature, the wear rate decreased accompanied by an increase in tribo-oxides. The fluctuation of friction coefficient was slight at 25–200°C but became violent at 400°C. At 25–200°C, adhesive wear prevailed due to trace or less tribo-oxides; at 400°C, oxidative wear prevailed with the predominant tribo-oxides of Fe₃O₄ and Fe₂O₃. It can be suggested that the antioxidation of the stainless steel postponed the occurrence of oxidative wear to a higher test temperature. For adhesive wear, the wear resistance, roughly following Archard's rule, was directly proportional to hardness besides the specimen tempered at 500°C with grain boundary brittleness. But for elevated-temperature wear, a better wear resistance required thermal stability and an appropriate combination of hardness and toughness.     

Sliding wear of graphite crystallized chromium white cast iron

The effects of sliding velocity, heat-treatment and graphite shape on sliding wear of graphite crystallized chromium white cast iron were studied. Two types of graphite crystallized chromium white cast irons having flaky or spheroidal and another type of 2.6C–15Cr white cast iron were prepared for this study. The effect of sliding velocity on wear resistance was studied by the Okoshi type and pin-on-disk type wear tests on materials which have experienced “as cast” and “heat-treated” conditions. The Okoshi type wear test results are divided into two relationships depending on sliding velocity or distance. Two regimes, initial wear and steady-state wear, existed for wear loss and sliding distance. A characteristic form of wear curve with a peak and a minimum was obtained when correlating wear loss and sliding velocity. The wear resistance of graphite crystallized chromium white cast irons were superior to that of 2.6C–15Cr white cast iron. In the results of pin-on-disk tests, there was no clear difference in the reported wear loss and friction coefficient among the alloys. However, an opposite tendency has appeared in the wear loss and friction coefficient: the wear loss value reached a peak in the wear curve at 0.52 m/s, while the friction coefficient reached a minimum at 0.52 m/s.     

Tribology of ultra-high molecular weight polyethylene disks molded at different temperatures

Tribological characteristics of ultra-high molecular weight polyethylene (UHMW-PE) disks molded at 130–190 °C were studied. The highest crystallinity was obtained for the sheet molded at 130 °C, but crystallinity decreased with increasing molding temperature. Beyond 150 °C, the resultant crystallinity reached a constant level. The dynamic friction coefficients of these UHMW-PE disks were measured using a ball-on-disk friction tester. The friction coefficient decreased with increasing number of rotations in the early stage of the measurement, and achieved at an equilibrium level, independent of the molding temperature. The steady-state friction coefficient was 0.04 for the disk molded at 130 °C and increased with increasing molding temperature. The disks molded at 150–190 °C always had a steady-state friction coefficient of 0.065. The surface deformation of each disk was evaluated from the observation of the resultant wear track. Analyzing the relationship between the above friction coefficient and width of the wear track enabled us to interpret the tribological mechanism generated in this study.