Drehen und Fräsen pulvermetallurgischer Hartlegierungen für warmgehende Werkzeuge

Turning and Milling of Powder Metallurgical Hard Alloys for Tools in Hot Working Applications Hard metals are high wear resistant materials. The microstructure of these composites consists of hard phases which are embedded in a metal matrix. The high hardness and the high content of the hard phases lead to a difficult machining of these materials. The present study investigates the turning and milling of D3 cold work steel (X210 Cr 12) and the powder metallurgical Fe‐based alloys ASP60 and ASP23 + WC/W₂C. The cutting tool materials were polycrystalline cubic boron nitrides (CBN) and ceramic inserts. The machining process could be judged by means of tool wear and machining quality (surface roughness and changes in the surface near zone). The investigations illustrate that the machinability of the different hard metals depends on the cutting speed and the cutting tool material.     

Machining of high performance workpiece materials with CBN coated cutting tools

The machining of high performance workpiece materials requires significantly harder cutting materials. In hard machining, the early tool wear occurs due to high process forces and temperatures. The hardest known material is the diamond, but steel materials cannot be machined with diamond tools because of the reactivity of iron with carbon. Cubic boron nitride (cBN) is the second hardest of all known materials. The supply of such PcBN indexable inserts, which are only geometrically simple and available, requires several work procedures and is cost-intensive. The development of a cBN coating for cutting tools, combine the advantages of a thin film system and of cBN. Flexible cemented carbide tools, in respect to the geometry can be coated. The cBN films with a thickness of up to 2 µm on cemented carbide substrates show excellent mechanical and physical properties. This paper describes the results of the machining of various workpiece materials in turning and milling operations regarding the tool life, resultant cutting force components and workpiece surface roughness. In turning tests of Inconel 718 and milling tests of chrome steel the high potential of cBN coatings for dry machining was proven. The results of the experiments were compared with common used tool coatings for the hard machining. Additionally, the wear mechanisms adhesion, abrasion, surface fatigue and tribo-oxidation were researched in model wear experiments.     

Cutting tool material selection using grey complex proportional assessment method

In today’s metalworking industry, many types of materials, ranging from high carbon steel to ceramics and diamonds, are used as cutting tools. Because of the wide range of conditions and requirements, no single cutting tool material meets all the needs of machining applications. Each tool material has its own properties and characteristics that make it best for a specific machining application. While evaluating a cutting tool material for a machining operation, the applicability is dependant on having the correct combination of its physical properties. Thus, it is extensively important to select the most appropriate cutting tool material with the desired properties for enhanced machining performance. This paper considers an exhaustive list of 19 cutting tool materials whose performance are evaluated based on ten selection criteria. The grey complex proportional assessment (COPRAS-G) method is then applied to solve this cutting tool material selection problem considering grey data in the decision matrix. Synthetic single crystal and polycrystal diamonds emerge out as the best two choices. Oil quenched tool steel (AISI O2) and powder metal tool steel (AISI A11) may also be used as the suitable cutting tool materials. Sialon and sintered reaction bonded silicon nitride are the worst chosen cutting tool materials.     

Investigations on hard machining of Impax Hi Hard tool steel

In this paper, experimental investigations are carried out by end milling process on hardened tool steel, Impax Hi Hard (Hardness 55 HRC) a newly developed tool steel material used by tool and die making industries. Experiments are performed with an aim to study performance investigations of machining parameters such as cutting speed, feed, depth of cut and width of cut with consideration of multiple responses viz. volume of material removed, tool wear, tool life and surface finish to evaluate the performance of PVD coated carbide inserts and ball end mill cutters. It has been observed through scanning electron microscope, X-ray diffraction technique (EDX) that chipping and adhesion are active tool wear mechanisms and saw-toothed chips are formed while machining of Impax Hi Hard steel. It is also noticed out that tool life is not enhanced while machining with minimum quantity lubricant than dry machining. From the investigations, it is observed that hard machining can be considered as an alternative to grinding and EDM, traditional methods of machining difficult-to-machine materials i.e. hardened steel with hardness greater than 50 HRC with a scope of improved productivity, increased flexibility, decreased capital expenses and reduced environmental waste.     

难加工材料的高速铣削研究进展

目的 分析难加工材料在高速切削过程中的基本形式及其特点,归纳总结现有的高速切削理论及现象。方法 主要从难加工材料的实验现象和仿真出发,分析高速加工机理,将现有高速铣削方法及其进展进行解析。结果 高速切削在宏观领域的研究主要集中在切屑的形成与刀具磨损,而在微观加工领域,主要研究材料属性及微观结构对于加工的影响。结论 从研究趋势上看,对宏观加工模型和微观理论分析的研究均有进展,但对微观模型的研究逐渐成为了近年来的研究热点。     

Effects of Lubricant Condition and Tool Wear in Hard Turning of Novel-Abrasion-Resistance (N-AR) Cast Iron

Advanced materials, such as high abrasion resistant cast iron, have great applications for abrasive and erosive environments. Since the amount and the hardness of the microstructural carbides constituents in this material is extremely high, the abrasion-resistance cast iron is generally difficult to be machined with traditional cemented carbide tool. The hard and abrasive particles in this material can remarkably shorten the cutting tool life through abrasion of tool face and deterioration of cutting edge. In this article, Cubic Boron Nitride (CBN) cutting tool has been used to machine a novel-abrasion-resistance (N-AR) cast iron. The performances of CBN tool under different lubrication conditions were evaluated in view of tool wear, cutting force, and surface roughness (Rz). Further more, the wear rate of CBN tool under different machining condition and the mechanism of the CBN tool in machining of this type of work materials has also been investigated.     

Tool wear mechanisms in axial ultrasonic vibration assisted milling in-situ TiB2/7050Al metal matrix composites

The in-situ TiB₂ particle reinforced aluminum matrix composites are materials that are difficult to machine, owing to hard ceramic particles in the matrix. In the milling process, the polycrystalline diamond (PCD) tools are used for machining these materials instead of carbide cutting tools, which significantly increase the machining cost. In this study, ultrasonic vibration method was applied for milling in-situ TiB₂/7050Al metal matrix composites using a TiAlN coated carbide end milling tool. To completely understand the tool wear mechanism in ultrasonic-vibration assisted milling (UAM), the relative motion of the cutting tool and interaction of workpiecetool-chip contact interface was analyzed in detail. Additionally, a comparative experimental study with and without ultrasonic vibration was carried out to investigate the influences of ultrasonic vibration and cutting parameters on the cutting force, tool life and tool wear mechanism. The results show that the motion of the cutting tool relative to the chip changes periodically in the helical direction and the separation of tool and chip occurs in the transverse direction in one vibration period, in ultrasonic vibration assisted cutting. Large instantaneous acceleration can be obtained in axial ultrasonic vibration milling. The cutting force in axial direction is significantly reduced by 42%-57%, 40%-57% and 44%-54%, at different cutting speeds, feed rates and cutting depths, respectively, compared with that in conventional milling. Additionally, the tool life is prolonged approximately 2-5 times when the ultrasonic vibration method is applied. The tool wear pattern microcracks are only found in UAM. These might be of great importance for future research in order to understand the cutting mechanisms in UAM of in-situ TiB₂/7050Al metal matrix composites.The full text can be downloaded at https://link.springer.com/article/10.1007/s40436-020-00294-2     

Experimental investigation of IN725 under different cooling environments using new tool holder

Heat buildup is an important issue on the cutting edge which then promotes high-temperature wear which consequently leads to poor machinability during dry machining. To improve the machinability, new tool holder designs accommodating cooling techniques have paid considerable attention toward the manufacturing domain recently. Whereas, in this paper, a new tool holder is designed and fabricated to serve for multipurpose cooling arrangements (internal cooling, external cooling) to reduce the heat buildup of the cutting edge along with the consolidated air system to clear away the chips. Initially, need of new tool holder is discussed followed by its manufacturability and machinability characteristics to a machine for nickel alloy Inconel 725. Machinability studies then are compared for dry machining, internal and external wet machining, and tool wear results are discussed. Thus, improvement in tool wear of around 70–75% and 65–72% is observed for internal wet, external wet concerning dry machining, respectively. Whereas, 15–18% (flank wear) and 6–9% (nose wear) improvement are seen for internal wet machining when compared with external wet machining. Results are best understood for internal cooling using a new tool holder.     

Prediction of cutting force based on machining parameters on AL7075-T6 aluminum alloy by response surface methodology in end milling

Cutting forces modeling is the basic to understand the cutting process, which should be kept in minimum to reduce tool deflection, vibration, tool wear and optimize the process parameters in order to obtain a high quality product within minimum machining time. In this paper a statistical model has been developed to predict cutting force in terms of geometrical parameters such as rake angle, nose radius of cutting tool and machining parameters such as cutting speed, cutting feed and axial depth of cut. Response surface methodology experimental design was employed for conducting experiments. The work piece material is Aluminum (Al 7075-T6) and the tool used is high speed steel end mill cutter with different tool geometry. The cutting forces are measured using three axis milling tool dynamometer. The second order mathematical model in terms of machining parameters is developed for predicting cutting forces. The adequacy of the model is checked by employing ANOVA. The direct effect of the process parameter with cutting forces are analyzed, which helps to select process parameter in order to keep cutting forces minimum, which ensures the stability of end milling process. The study observed that feed rate has the highest statistical and physical influence on cutting force.     

SiCP/2024复合材料切削力与刀具磨损的试验研究

本文通过SiC_P/2024复合材料的车削试验,得出了刀具材料、切削用量及SiC_P含量对切削力和刀具磨损的影响规律。并认为K类硬质合金可用于粗加工和半精加工,而且要采用较低切削速度和较大进给量,但SiC_P含量较高时会出现切深分力大于主切削力。SiC_P含量越高差值越大;PDC是精加工最佳刀具材料,也不会出现切深分力大于主切削力现象     

Experimental and numerical investigation of thermal loads in Inocnel 718 machining

Inducing high thermal loads in machining of difficult-to-cut materials changes the mechanical properties of a machined surface/subsurface. In particular, a thermally affected layer leads to tensile residual stresses and microstructure changes. Nickel-based alloys are hard materials and frequently used in different industries. Since the generation of thermal loads in machining Inconel 718 is evident, in this paper an experimental and numerical investigation were performed to evaluate thermal loads and the depth of the affected layer in the machining of Inconel 718 superalloy. First, the effect of cutting parameters was studied on the average machined surface temperature by experimental tests. Then, the results of experiments were used to validate a 3D numerical model. Using the calibration strategy, the heat transfer coefficient at the chip–tool interface was found to be dependent on the cutting conditions. Next, the effect of the initial workpiece hardness and tool geometry, including tool nose radius and edge radius, was evaluated on thermal loads and the depth of the recrystallized layer. The critical strain criterion was used to estimate the depth of the recrystallized layer and then, the numerical results were compared with experimentally measured depth of the affected layer at different machining parameters.     

Multi-attribute optimization of end milling epoxy granite composites using TOPSIS

Epoxy granite composites are identified and recognized as better materials for machine tool applications due to inherent damping properties. However, end milling of these composites has not been explored much. Milling of epoxy granite composites presents a number of problems, namely, cutting forces and surface roughness appear during machining. This research work focuses on end milling of epoxy granite composite specimens using high-speed steel end mill cutter by varying the cutting conditions such as spindle speed and feed with a uniform depth of cut and selection of optimal machining parameters. The experimental runs of 27 different trials were carried out and three different attributes such as thrust force, tangential force, and surface roughness were analyzed. This research work presents a sequential procedure for machining parameters selection. Selection of optimal machining parameters is done on the basis of Technique for Order Preference by Similarity to Ideal Solution (TOPSIS) method.     

Experimental Study of Surface Roughness and Tool Flank Wear during Hybrid Milling

Two advanced machining methods such as thermally enhanced machining and ultrasonic-assisted machining are recently considered in many studies. In this article, a new hybrid milling process is presented by gathering the characteristics of these two methods. In order to determine the axial depth of cut and engagement in the process, three-dimensional thermal finite-element analysis is applied to determine the dimensions of softened materials. Finite-element modal analysis is used to determine the dimensions and clamping state of the workpiece while cutting area has the highest vibration amplitude. Full factorial experimental design is applied to investigate the effect of hybrid machining parameters on the surface roughness and tool wear. Tool flank wear was investigated under the condition of constant cutting speed during different period of times. Hybrid milling process with an amplitude of 6 µm and a temperature of 900°C creates a surface with 42% lower roughness in comparison to conventional milling in feed 0.08 mm/tooth. In a study of tool flank wear, the results show that application of TEUAM decreases flank wear at least 16% in comparison to all other processes.     

Optimization of cryo-treated EDM variables using TOPSIS-based TLBO algorithm

In order to machine hard and high-strength-to-weight ratio materials, electrical discharge machining (EDM) process is extensively used in aerospace, automobile and other industrial applications. However, high erosion of tool and improper selection of machining variables have emerged as a major obstruction to achieve productivity in this direction. High erosion of tool not only enhances the cost of machining but also increases the machining time by causing interruption during machining. Therefore, proper selection of machining variables and tool material life are the two vital aspects for the tool engineers working in EDM. In view of this, the present work proposes an extensive experimental investigation and optimization of machining variables of cryogenically treated brass tool materials on machining competences of Inconel 718 workpiece. The study primarily highlights the outcome of cryogenically treated soaking duration of tools along with other important process variables, viz. discharge current, open-circuit voltage, pulse-on time, duty factor and flushing pressure, on the performance measures such as electrode wear ratio (EWR), surface roughness and radial over-cut. The study revealed that soaking duration in deep cryo-treatment of the electrode is a significant variable to achieve improved machining characteristics. The performance measures are converted into equivalent single performance measure by calculating the relative closeness coefficient by the techniques for order preferences by similarity to ideal solution (TOPSIS) approach. Finally, a novel teaching–learning-based optimization (TLBO) algorithm has been proposed to find the optimal level of machining variables for the performance measures. The optimal levels of cutting variables obtained through the algorithm are validated through confirmation test, predicting an error of 2.171 percentages between the computational and experimental results. The predicted result suggests that the proposed model can be used to select the ideal process states to achieve productivity for the cryo-treated EDM.     

铝基碳化硅精密铣削刀具磨损实验研究

针对铝基碳化硅切削加工中刀具易磨损、寿命低、切削难度大和加工成本高等问题,选用不同材料的硬质合金铣刀及金刚石铣刀进行切削加工实验,并利用扫描电镜和工具显微镜对高体积分数铝基碳化硅铣削时刀具磨损形态进行了分析研究.研究表明:硬质合金刀具前刀面和刃口磨损主要形式为粘结磨损和微崩刃,后刀面磨损主要为刻划磨损,而金刚石铣刀加工时刀具磨损很小;YG6X铣刀材料微观组织致密,抗磨损能力较强,宜粗加工时选用;金刚石刀体的硬度远大于SiC颗粒,且金刚石与工件的摩擦系数小,金刚石铣刀寿命远大于硬质合金铣刀,宜精加工时选用.     

A study on milling of glass fiber reinforced plastics manufactured by hand-lay up using statistical analysis (ANOVA)

Milling is the most practical machining (corrective) operation for removing excess material to produce a well defined and high quality surface. However, milling composite materials presents a number of problems such as surface delamination associated with the characteristics of the material and the cutting parameters used. In order to minimize these problem is presented a study with the objective of evaluating the cutting parameters (cutting velocity and feed rate) related to machining force in the workpiece, delamination factor, surface roughness and international dimensional precision in two GFRP composite materials (Viapal VUP 9731 and ATLAC 382-05). A plan of experiments, based on an orthogonal array, was established considering milling with prefixed cutting parameters. Finally an analysis of variance (ANOVA) was preformed to investigate the cutting characteristics of GFRP composite materials using a cemented carbide (K10) end mill.     

Influence of radial depth of cut on entry conditions and dynamics in face milling application

The choice of milling cutter geometry and appropriate cutting data for certain milling application is of vital importance for successful machining results. Unfavorable selection of cutting conditions might give rise to high load impacts that cause severe cutting edge damage. Under some circumstances the radial depth of cut in combination with milling cutter geometry might give unfavorable entry conditions in terms of cutting forces and vibration amplitudes. This phenomenon is originated from the geometrical features that affect the rise time of the cutting edge engagement into workpiece at different radial depths of cut. As the radial depth of cut is often an important parameter, particularly when machining difficult-to-cut materials, it is important to explore the driving mechanism behind vibrations generation. In this study, acceleration of the workpiece is measured for different radial depths of cut and cutting edge geometries. The influence of the radial depth of cut on the dynamical behavior is evaluated in time and frequency domains. The results for different radial depths of cut and cutting geometries are quantified using the root mean square value of acceleration. The outcome of this research study can be used both for the better cutting data recommendations and improved tool design.     

Analysis of hard turning process:thermal aspects

In manufacturing sector,hard turning has emerged as a vital machining process for cutting hardened steels.Besides many advantages of hard turning operations,one has to implement to achieve close tolerances in terms of surface finish,high product quality,reduced machining time,low operating cost and environmental friendly characteristics.In the study,three dimensional(3D) computer aided engineering(CAE) based simulation of hard turning by using commercial software DEFORM 3D has been compared to the experimental results of stresses,temperatures and tool forces in machining of AISI D3 and AISI H13 steel using mixed ceramic inserts(CC6050).In the following analysis,orthogonal cutting models are proposed,considering several processing parameters such as cutting speed,feed and depth of cut.An exhaustive friction modelling at the tool-work interface is carried out.Work material flow around the cutting edge is carefully modelled with adaptive re-meshing simulation capability of DEFORM 3D.The process simulations are performed at constant feed rate(0.075 mm/r) and cutting speed(155 m/min),and analysis is focused on stresses,forces and temperatures generated during the process of machining.Close agreement is observed between the CAE simulation and experimental values.     

Ein neues Werkstoffkonzept zur trockenen Bearbeitung mineralischer Materialien

A new material concept for machining of mineral materials For the machining of mineral materials like rock, concrete and asphalt ultra hard cutting‐tools such as diamond tools are used. During the use diamond tools are cooled with water to remove the heat and to prevent an early deterioration of the diamonds. Without water cooling the diamonds at the cutting edge as well as in lower levels are damaged. For ecological and economic reasons a dry machining of mineral materials is of great interest. The consumption of coolant and the pollution of occupied buildings by alkaline water would be decreased. But specific diamonds tools are necessary to realise a dry machining. The Institute of Materials Engineering pursues a novel material concept for diamond impregnated composites to protect diamonds in deeper layers. Materials with a very low thermal conductivity are inserted in the diamond‐composites to protect the diamonds against heat and to reduce the deterioration of diamonds in lower levels. Cobalt and bronze (CuSn 85/15) with particle sizes of 45–90 μm and < 40 μm, diamonds with particle sizes of 300–450 μm and alumina with particle sizes of 350–500 μm, 150–210 μm and < 70 μm were used. The diamond‐alumina‐composites were powder metallurgically produced and were examined by light‐ and electron microscopy and digital image analysis.     

Studies on Machining Parameters While Milling Particle Reinforced Hybrid (Al6061/Al2O3/Gr) MMC

In this article, response surface methodology has been used for finding the optimal machining parameters values for cutting force, surface roughness, and tool wear while milling aluminum hybrid composites. In order to perform the experiment, various machining parameters such as feed, cutting speed, depth of cut, and weight (wt) fraction of alumina (Al₂O₃) were planned based on face-centered, central composite design. Stir casting method is used to fabricate the composites with various wt fractions (5%, 10%, and 15%) of Al₂O₃. The multiple regression analysis is used to develop mathematical models, and the models are tested using analysis of variance (ANOVA). Evaluation on the effects and interactions of the machining parameters on the cutting force, surface roughness, and tool wear was carried out using ANOVA. The developed models were used for multiple-response optimization by desirability function approach to determine the optimum machining parameters. The optimum machining parameters obtained from the experimental results showed that lower cutting force, surface roughness, and tool wear can be obtained by employing the combination of higher cutting speed, low feed, lower depth of cut, and higher wt fraction of alumina when face milling hybrid composites using polycrystalline diamond insert.