Water absorption and dimensional stability of short kenaf fiber‐filled polypropylene composites treated with maleated polypropylene

The purpose of this research was to investigate the water absorption behavior and associated dimensional stability of kenaf‐polypropylene‐filled (PP/KF) composites. Composites with different fiber loadings, ranging from 0 to 40 wt %, were prepared with a twin‐screw extruder followed by hot press molding. The influence of the compatibilizer was also studied for PP/KF composite with 5 wt % maleated PP (MAPP). Water absorption testing was carried out at room temperature for 7 weeks. Tensile, flexural, and impact tests were also performed on control, wet, and re‐dried specimens. Increasing the fiber content resulted in higher water absorption and thickness swelling. The inferior mechanical properties of the wet composites were attributed to the effect of water, which deteriorates the interfacial properties of composites. On re‐drying, all properties were almost recovered because of the recovery of interfacial area as evident in scanning electron micrographs. Incorporation of the MAPP significantly improved the compatibility between the fiber and matrix and the mechanical properties of the composites compared with those without MAPP. It also diminished the water absorption as well as the related thickness swelling in the composites. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Steam‐exploded residual softwood‐filled polypropylene composites

Residual softwood sawdust was pretreated by a steam‐explosion technique. It was used as a natural filler in polypropylene (PP)‐based composites. Dynamic mechanical analysis and tensile properties of these materials were studied. The influence of filler loading, steam‐explosion severity, and coating the fiber with a functionalized compatibilizer, such as maleic anhydryde polypropylene (MAPP), on the mechanical behavior of the composite was evaluated. The results were analyzed in relation with scanning electron microscopy observations, and surface energy (dispersive and polar components) and apparent specific area measurements. Experimental data indicate a better compatibility between MAPP‐coated fiber and PP with respect to the untreated one. The coating treatment of the softwood fiber was found to promote interfacial adhesion between both components, and to enhance the tensile properties of the resulting composite. This reinforcing effect was well predicted from theoretical calculations based on a mean field approach (Halpin‐Kardos model). The steam‐explosion pretreatment severity increased the surface energy and apparent specific surface, and resulted in a loss of the fiber entirety. The sorption behavior of these composite materials was also performed. It was found that the composites absorb more water, as the filler content is higher. MAPP coating provided protection from water uptake in the interphase region. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 1962–1977, 1999     

Polypropylene (PP)–Acacia mangiumcomposites: the effect of acetylation on mechanical and water absorption properties

Acacia mangiumwood flour (AMWF)–polypropylene (PP) composites were produced at different filler loading (20, 30, 40, and 50 w/w) and mesh no. (35, 60, 80, and 100 mesh). The AMWF–PP composites (using unmodified or modified wood flour) were compounded using a Haake Rheodrive 500 twin screw compounder. The mechanical and water absorption (WA) properties of modified (only at mesh no. 100) and unmodified AMWF–PP composites were investigated. Increase in the mesh number (35–100) of the unmodified AMWF showed increased flexural and impact properties. Flexural modulus exhibited higher properties as the filler loading increased (20–50). However, flexural and impact strength showed the opposite phenomenon. Water absorption and thickness swelling increased as the mesh number and filler loading increased. This has been attributed to the presence of hydrophilic hydroxyl groups of the filler. Modified AMWF–PP composites exhibited higher mechanical properties and good water resistance when compared to unmodified AMWF–PP composites at all values of filler loading. The evidence of the failure mechanism (from impact strength) of the filler–matrix interface was analyzed using scanning electron microscope.     

Morphological,mechanical, and physical properties of composites made with wood flour‐reinforced polypropylene/recycled poly(ethylene terephthalate) blends

Wood flour (WF)‐filled composites based on a polypropylene (PP)/recycled polyethylene terephthalate (r‐PET) matrix were prepared using two‐step extrusion. Maleic anhydride grafted polypropylene (MAPP) was added to improve the compatibility between polymer matrices and WF. The effects of filler and MAPP compatibilization on the water absorption, mechanical properties, and morphological features of PP/r‐PET/WF composites were investigated. The addition of MAPP significantly improved mechanical properties such as tensile strength, flexural strength, tensile modulus, and flexural modulus compared with uncompatibilized composites, but decreased elongation at break. Scanning electron microscopic images of fracture surface specimens revealed better interfacial interaction between WF and polymer matrix for MAPP‐compatibilized PP/r‐PET/WF composites. MAPP‐compatibilized PP/r‐PET/WF composites also showed reduced water absorption due to improved interfacial bonding, which limited the amount of absorbable water molecules. These results indicated that MAPP acts as an effective compatibilizer in PP/r‐PET/WF composites. POLYM. COMPOS., 38:1749–1755, 2017. © 2015 Society of Plastics Engineers     

连续式蒸汽爆破对PP/棉杆纤维复合材料力学性能的影响

以连续式蒸汽爆破预处理的棉杆作为增强纤维,通过模压成型制得聚丙烯(PP)/棉杆纤维复合材料.研究了蒸汽爆破条件中纤维含水量及爆破次数对复合材料力学性能的影响.结果表明,该预处理使复合材料力学性得以改善.当纤维含水量为40%、爆破次数两次时,获得的复合材料综合力学性能最佳.     

Isolation and characterization of betel nut leaf fiber: Its potential application in making composites

Betel nut leaf fiber (BNLF) is a new finding as cellulosic filler for polymer composites. Its main constituents are 75% α‐cellulose, 12% hemicelluloses, 10% lignin, and 3% others matter, viscosity average molecular weight 132,000 and degree of crystallinity 70%. In the present work, BNLF reinforced polypropylene (PP) composites were prepared using heat press molding method. 5–20 wt% short length fiber is taken for getting benefits of easy manufacturing and the fiber was chemically treated with NaOH, dicumyl peroxide (DCP), and maleic anhydride‐modified PP (MAPP) to promote the interfacial bond with PP. The extent of modification of fiber was assessed on the basis of morphology, bulk density, moisture absorption, thermal, and mechanical properties of untreated fiber, treated fiber, and their reinforcing PP composites. The tensile and flexural strength of composites increase with the increase of fiber loading up to 10 and 20 wt%, respectively. It was also observed that Young's modulus and flexural modulus increase with fiber loading. The thermal degradation behavior of resulting composites was investigated. Among the various treated fibers, MAPP‐treated fiber composite showed best interfacial interactions as well as mechanical and thermal properties. POLYM. COMPOS., 2012. © 2012 Society of Plastics Engineers     

The effects of maleated polybutadiene‐grafted polypropylene (MAPB‐g‐PP) content on the properties of wood flour/polypropylene composites

This research investigated the effects of a compatibilizer of maleated polybutadiene‐grafted polypropylene (MAPB‐g‐PP) on the properties of wood‐flour/polypropylene composites through the analysis of mechanical properties, water absorption, thermogravimetry, differential scanning calorimetry, and scanning electronic microscopy. The results demonstrate that the mechanical properties of composites were significantly increased; the thermal stability and water absorption were improved. The crystallization temperature and crystallinity were decreased. These improvements have been attributed to the strong interfacial interaction of MAPB‐g‐PP with both wood and polypropylene. J. VINYL ADDIT. TECHNOL., 26:17–23, 2020. © 2019 Society of Plastics Engineers     

Properties of glycerin‐thermally modified wood flour/polypropylene composites

This study aimed to investigate the combination effect of glycerin treatment and thermal modification of wood flour on the physical, mechanical, thermal dynamic mechanical properties of wood flour/polypropylene (PP) composite. The morphological aspect was also investigated. The wood flour was first impregnated in the aqueous solution of glycerin, followed by heat treatment at 200°C for 1 h. Then the unmodified or modified wood flour was blended with PP at a weight ratio of 4:6 to prepare composites. Moisture adsorption experiment and X‐ray photoelectron spectroscopy analysis of wood flour demonstrated that the hygroscopicity and the free surface hydroxyl groups of wood flour decreased after glycerin‐thermal modification. Thickness swelling of the 10% wt glycerin‐thermally modified wood flour/PP composite was reduced by 42.8% after 96 h immersion as compared to unmodified control. Evaluation of mechanical properties in impact and flexure modes indicated that glycerin treatment alone had no significant effect, but the combination of glycerin and thermal treatment slightly decreased the strength, with the exception of 10% glycerin and heat modified sample. Dynamic mechanical analysis and scanning electron microscope illustrated the improved interfacial bonding between PP and wood flour modified by 10% glycerin and heat treatment. POLYM. COMPOS., 35:201–207, 2014. © 2013 Society of Plastics Engineers     

Effects of hygrothermal ageing on mechanical properties of flax pulps and their polypropylene matrix composites

The aim of this work was to study the kinetics of water uptake and its influence on mechanical behavior of both flax pulps and their composites with a maleic anhydride polypropylene copolymer (MAPP) modified polypropylene (PP) matrix by immersion in distilled water at 30, 50, 70, and 100°C. Both the influence of two different MAPP compatibilizers and the optimum doses of each ones were analyzed. The kinetics of water uptake was studied from weight measurements at regular interval times. The diffusion coefficient was dependent on the immersion temperature and MAPP content. Tensile modulus and strength of single flax fiber decreased by water immersion. Both flexural strength and modulus of composites decreased as a result of the combined effect of thermal ageing and moisture absorption. MAPP coupling agent increases moisture resistance and mechanical properties for MAPP‐modified systems with respect to the unmodified ones. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 3438–3445, 2006     

Mechanical properties of modified biofiller‐polypropylene composites

This article reports the mechanical, thermal, and morphological properties of polypropylene (PP)‐chicken eggshell (ES) composites. Mechanical properties like tensile strength, tensile modulus, izod impact strength, flexural modulus of PP composites with normal (unmodified) eggshell and chemically treated ES [modified ES (MES) with isophthalic acid] have been investigated. PP–calcium carbonate (CaCO₃) composites, at the same filler loadings, were also prepared and used as reference. The results showed that PP composites with chemically MES had better mechanical properties compared to the unmodified ES and CaCO₃ composites. An increase of about 3–18% in tensile modulus, 4–44% in izod impact strength and 1.5–26% in flexural modulus at different filler loading was observed in MES composites as compared to unmodified ES composites. Scanning electron microscopy (SEM) micrographs of fractured tensile specimens confirmed better interfacial adhesion of MES with polymer matrix resulting into lower voids and plastic deformation resulting in improved mechanicals of the composites. TEM micrographs showed acicular needle shaped morphology for modified ES and have contributed to better dispersion which is the prime reason for enhancement of all the mechanical properties. At higher filler loading, the modulus of MES composite was found to be higher by 5% as compared to commercial CaCO₃ composites. POLYM. COMPOS., 35:708–714, 2014. © 2013 Society of Plastics Engineers     

Broom fibers as reinforcing materials for polypropylene-based composites

Broom fibers have been used as reinforcement for the conventional polypropylene (iPP) and a maleate modified one (iPPMA). A conventional alkaline treatment and a steam explosion extraction process were applied to obtain the cellulosic material from broom branches. Composites were prepared by melt mixing materials with different weight percentages of broom fibers. Also ternary blends (iPPMA/iPP/broom fibers 5/45/50 wt) were obtained to examine the possibility of utilizing the maleate polypropylene as a compatibilizing agent. The fibers and the composites were thermally, morphologically, and mechanically characterized. Water absorption tests, to examine the behavior of these materials in wet conditions, were also performed. Particular attention was addressed to the study of the fiber/matrix interfacial adhesion. The results showed that the iPPMA-based composites, reinforced with alkaline extracted broom fibers, present specific mechanical properties competitive with those of the homologous polypropylene-based materials reinforced with short glass fibers. The ternary blends gave similar properties to those of the corresponding whole iPPMA-based composites. It is considered that the esteric linkage between the cellulose —OH, and the maleic anhydride groups grafted on the polypropylene backbone is greatly responsible for the similarity in the properties. In spite of better adhesion observed in the samples reinforced by the steam-exploded fibers, less improvement of the mechanical properties was observed, owing to significant damage of the structure of the fibers during the steam explosion process. A general decrease of mechanical properties is observed in normal polypropylene-based composites. The results are also supported by the water absorption tests: whereby the iPPMA-based composites showed good capability to return their dry properties when kept in an oven after wetting for many days. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 68: 1077–1089, 1998     

The effect of various anhydride modifications on mechanical properties and water absorption of oil palm empty fruit bunches reinforced polyester composites

The chemical modification of oil palm empty fruit bunches (EFB) using non‐catalysed reaction with acetic, propionic and succinic anhydrides were investigated. Proof of modification was indicated by the increase of weight and was confirmed by Fourier‐transform infrared analysis (FT‐IR). The mechanical and water‐absorption properties of all anhydride‐modified EFB composites were evaluated at different volume fractions (V_f). The properties were improved for these modified fibres, whereas unmodified EFB fibres exhibited poor mechanical properties and higher water absorption. Acetic anhydride modification showed the greatest benefit on composite properties, followed by propionic and succinic anhydride modification. © 2001 Society of Chemical Industry     

Evaluation of Kraft lignin as natural compatibilizer in wood flour/polypropylene composites

This study investigated the effect of Kraft lignin as natural compatibilizer on the water absorption, thermal, mechanical, and interfacial properties of poplar wood flour (WF)/polypropylene (PP) composites. Varying contents (0.5, 1, 2, 4, and 8 wt%) of lignin were added to WF and PP by direct mixing, then the composites were prepared by two‐screw extrusion and compression moulding. Results showed that lignin incorporation reduced the water absorption and postponed the thermal decomposition of the composites. Composites with lower lignin contents (0.5% and 1%) could get the optimal properties, and the excess lignin contents (4% and 8%) resulted in slight decrease in the mechanical properties. DMA and calculation of adhesion factor showed that the composites with 0.5% lignin had the best interaction between WF and PP. The morphologies of fractured surface also indicated improved interfacial adhesion between WF and PP from the addition of 0.5% and 1% lignin. POLYM. COMPOS., 38:2387–2394, 2017. © 2015 Society of Plastics Engineers     

Effect of clinoptilolite filler on the physical and mechanical properties of polypropylene

This study aims to investigate the mechanical and physical properties of polypropylene (PP) filled by natural zeolite. For this purpose, a natural zeolite (at 1–6 wt% filler loadings) with two different particle sizes was used. Two different kinds of silane coupling agents (3‐aminopropyltriethoxysilane, GAPTES and 3‐glycidoxypropyltrimethoxysilane, GPTMS) at three different volume ratios were used to improve the zeolite compatibility with PP and to improve the mechanical properties of composites. Fillers and PP were compounded with a twin screw extruder, and the composites were moulded with injection moulding press. The samples were subjected to mechanical tests (i.e., impact and tensile tests) and physical tests (i.e., hardness, density, and melt flow index, MFI). The physical test results showed that the levels of hardness and density of both unmodified and modified zeolite‐filled PP composites were higher compared with neat PP. The MFI values of composites were decreased by increasing zeolite loading level. Composites including GAPTES modified zeolite showed improved yield strength, impact strength and stiffness compared with composites filled with unmodified zeolite particles. POLYM. COMPOS. 34:1396–1403, 2013. © 2013 Society of Plastics Engineers     

Polymer nanocomposite powders and melt spun fibers filled with silica nanoparticles

Nanocomposite powders from polypropylene filled with surface modified and unmodified fumed silica have been prepared from polymer solution to achieve improved mixing and have been forwarded to fiber melt spinning. The surface of the fumed silica was modified with dodecyl alkoxy silanes. Crystallization velocity and viscosity of the PP nanocomposites thereof were determined to ensure good melt spinning processing conditions for all composite compositions. Upon addition of untreated filler particles, a shear thinning and an increased crystallization velocity of the polymer melt was found, while only minor changes were detected in the presence of surface modified fumed silica particles. The composites and the polymer fibers made from these powder composites by melt spinning were mainly characterized by optical microscopy (OM), scanning electron microscopy (SEM), mechanical measurements, differential scanning calorimetry (DSC), and solid‐state NMR. The unmodified fumed silica was found to have a strong influence on the mechanical fiber properties, while the surface modified silica only a small one. Fibers were additionally characterized with respect to the uniformity, the PP crystallinity, moisture absorption, and the water contact angle. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 218–227, 2007     

Parameters regulating interfacial and mechanical properties of short glass fiber reinforced polypropylene

The performance of thermoplastic composites is known to depend on the intrinsic properties of the two composite components, the quality of the fiber–matrix interface, and the crystalline properties of their matrix. The objective of this work is to characterize the effect of the addition of modified polypropylene (PP) and silane coupling agent on the mechanical and interfacial properties of short fiber reinforced PP composites. Differential scanning calorimetry (DSC), single fiber composite fragmentation tests (SFC), and mechanical testing are used to understand the different parameters regulating the interfacial properties of composites. No influence of the modified PP on the level of crystallinity is observed. Some differences in the size of the spherulites are observed for acrylic acid grafted PP (PP‐g‐AA). Those samples also show lower mechanical properties in spite of good interfacial interactions. Maleic anhydride grafted PP (PP‐g‐MAh) leads to better mechanical performances than PP‐g‐AA. A high MAh content PP‐g‐MAh grade with low viscosity is the best polymeric additive used in the present work. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 78: 2047–2060, 2000     

The effect of epoxy‐polyester hybrid resin on mechanical properties,rheological behavior,and water absorption of polypropylene wood flour composites

The effect of epoxy resin on mechanical and Rheological properties, and moisture absorption of wood flour polypropylene composites (WPCs) were investigated. The reactive mixing of epoxy resin with 30, and 40 wt% wood flour and polypropylene (PP) was carried out in twin screw extruder with a special screw elements arrangement. PP grafted maleic anhydrides (MPP) were used as coupling agent to improve the interfacial interactions of wood flour, epoxy resin, and PP. The tensile strength of composites decreased, and elastic modulus and moisture absorption increased with increasing epoxy resin content. The complex viscosity η* increased with increasing epoxy resin content of composites, and a synergistic effect in increasing the η* was observed at 3 wt% resin. The epoxy resin modified wood‐PP composites that chemically coupled by MPP showed minimum water absorption with highest elastic modulus. The experimental oscillation rheologyical data were used to drive a model to predict the flow behavior of WPCs, in a wide range of frequencies. POLYM. ENG. SCI., 47:2041–2048, 2007. © 2007 Society of Plastics Engineers     

Bamboo fiber polypropylene composites: Effect of fiber treatment and nano clay on mechanical and thermal properties

In the current study, bamboo fibers were modified with sodium meta‐periodate in order to improve the mechanical and thermal properties of the bamboo‐clay‐polypropylene (PP) composites. Both raw and treated bamboo fibers were used in the manufacturing of the composites. The mechanical and thermal properties of the composites from modified bamboo fibers were found to increase considerably compared with those of untreated fibers. Tensile strengths of (raw bamboo fiber)/PP, (raw bamboo fiber‐clay)/PP, and (treated bamboo fiber‐clay)/PP composites showed a decreasing trend with increasing fiber loadings. However, the values for the chemically modified (bamboo fiber)‐clay‐PP composite at all mixing ratios were found to be higher than that of the original PP. The scanning electron micrographs showed that interfacial bonding between the treated fiber‐clay and matrix has significantly improved. It was determined that better dispersion of the filler into matrix occurred on 5% clay addition and fiber treatment. J. VINYL ADDIT. TECHNOL., 21:253–258, 2015. © 2014 Society of Plastics Engineers     

Surface modification of ultra‐high‐molecular‐weight polyethylene. II. Effect on the physicomechanical and tribological properties of ultra‐high‐molecular‐weight polyethylene/poly(ethylene terephthalate) composites

We performed surface modification of ultra‐high‐molecular‐weight polyethylene (UHMWPE) through chromic acid etching, with the aim of improving the performance of its composites with poly(ethylene terephthalate) (PET) fibers. In this article, we report on the morphology and physicomechanical and tribological properties of modified UHMWPE/PET composites. Composites containing chemically modified UHMWPE had higher impact properties than those based on unmodified UHMWPE because of improved interfacial bonding between the polymer matrix and the fibers and better dispersion of the fibers within the modified UHMWPE matrix. Chemical modification of UHMWPE before the introduction of PET fibers resulted in composites exhibiting improved wear resistance compared to the base material and compared to unmodified UHMWPE/PET composites. On the basis of the morphological studies of worn samples, microploughing and fatigue failure associated with microcracking were identified as the principle wear mechanisms. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci, 2006     

Preliminary studies on the use of modified ALCELL lignin as a coupling agent in the biofiber composites

ALCELL lignin has been employed as a coupling agent in empty fruit bunch fiber (EFBF)–polypropylene (PP) composites. The lignin has been chemically modified with toluene diisocyanate (TDI) to various weight loadings. The evidence of the reaction between TDI and lignin has been observed by using Fourier transform infrared (FTIR) analysis. The effect of lignin as a coupling agent on mechanical properties has been studied. The results show that the TDI‐modified lignin is able to impart greater compatibility between EFBF and PP. This is reflected in the greater mechanical properties shown by the composites with TDI‐modified lignin than in those with the unmodified lignin. Scanning electron microscopy (SEM) studies showed that TDI modification of lignin resulted in a better blending and compatibility between lignin and PP matrix. The glass‐transition temperature of the lignin increases as the WPG is increased. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 1333–1340, 2001