Synthesis and network parameters of hydrophobic poly(N‐[3‐(dimethylaminopropyl)]methacrylamide‐co‐lauryl acrylate) hydrogels

Hydrophobic poly(N‐[3‐(dimethylaminopropyl)]methacrylamide‐co‐lauryl acrylate) [P(DMAPMA‐co‐LA)] hydrogels with different LA content were synthesized by free‐radical crosslinking copolymerization of corresponding monomers in water by using N,N‐methylenebis(acrylamide) as the crosslinker, ammonium persulfate as the initiator, and N,N,N′,N′‐tetramethylethylenediamine as the activator. The swelling equilibrium of the hydrogels was investigated as a function of temperature and hydrophobic comonomer content in pure water. An interesting feature of the swelling behavior of the P(DMAPMA‐co‐LA) hydrogels with low LA content was the reshrinking phase transition where the hydrogels swell once and collapse as temperature was varied in the range of 30–40°C. The average molecular mass between crosslinks (M?_c) and polymer–solvent interaction parameter (χ) of the hydrogels were calculated from equilibrium swelling values. The enthalpy (ΔH) and entropy (ΔS) changes appearing in the χ parameter for the hydrogels were determined by using the Flory–Rehner theory based on the phantom network model of swelling equilibrium. The positive values for ΔH and ΔS indicated that the hydrogels had a positive temperature‐sensitive property in water, that is, swelling at a higher temperature and shrinking at a lower temperature. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 4159–4166, 2006     

Swelling characteristics of thermo‐ sensitive poly[(2‐diethylaminoethyl methacrylate)‐co‐(N,N‐dimethylacrylamide)] porous hydrogels

Temperature‐sensitive poly[(2‐diethylaminoethyl methacrylate)‐co‐(N,N‐dimethylacrylamide)] [P(DEAEMA‐co‐DMAAm)] hydrogels with five different DMAAm contents were synthesized with and without the addition of sodium carbonate as porosity generator. The synthesized hydrogels were characterized with dry gel density measurements, scanning electron microscopy observation and the determination of swelling ratio. The influence of the pore‐forming agent and content of DMAAm on swelling ratio and network parameters such as polymer–solvent interaction parameter (χ), average molecular mass between crosslinks (M?_c) and mesh size (ζ) of the cryogels are reported and discussed. The swelling and deswelling rates of the porous hydrogels are much faster than for the same type of hydrogels prepared via conventional methods. At a temperature below the volume phase transition temperature, the macroporous hydrogels also absorbed larger amounts water compared to that of conventional hydrogels and showed obviously higher equilibrated swelling ratios in aqueous medium. In particular, the unique macroporous structure provided numerous water channels for water diffusion in or out of the matrix and, therefore, an improved response rate to the external temperature changes during the deswelling and swelling processes. These properties are attributed to the macroporous and regularly arranged network of the porous hydrogels. Scanning electron micrographs reveal that the macroporous network structure of the hydrogels can be adjusted by applying porosity generation methods during the polymerization reaction. Copyright © 2007 Society of Chemical Industry     

Control of monodisperse particle size of styrenic–acrylate copolymers in dispersion copolymerization

Syntheses of monodisperse poly[(styrene)‐co‐(n‐butyl acrylate)] and poly[(styrene)‐co‐(2‐ethylhexyl acrylate)] were carried out by dispersion polymerization. The reactions were performed in the mixed solvent of ethanol–water in the presence of azo‐bisisobutyronitrile and poly(N‐vinylpyrrolidone) as the initiator and dispersant, respectively. The effects of reaction parameters, that is the type and concentration of dispersant, ratio of the mixed solvent, reaction temperature, agitation rate, monomer composition between styrene and n‐butyl acrylate or 2‐ethylhexyl acrylate, crosslinking agent and reaction time on the particle size, size distribution and average molecular weights of the resulting copolymer were thoroughly investigated. The resulting copolymer particles were smooth on their spherical surface and the sizes were in the range 0.6–1.8 µm with a narrow size distribution. In most cases, a correlation between small particle sizes with high average molecular weights was observed. The average particle size generally increased with increasing reaction temperature, time and acrylate monomer content. In contrast, the particle size decreased as the molecular weight, concentration of dispersant, polarity of the medium or agitation rate was increased. The glass transition temperature (T_g) of the copolymers can be controlled by the mole ratio of the comonomer. The T_g values decreased when the content of acrylate monomers in the copolymer increased, and T_g values of the synthesized copolymer were in the range 66–102 °C. Instead of using n‐butyl acrylate monomer in the copolymerization, 2‐ethylhexyl acrylate copolymerization with styrene resulted in insignificant changes in the particle sizes but there were significant decreases in T_g values. In this study, the monodisperse particles can be obtained by monitoring the appropriate conditions regarding PVP K‐30 (2–8 wt%), ethanol/water (90/10 wt%), the reaction temperature (70 °C) and the agitation rate (100 rpm). © 2000 Society of Chemical Industry     

Water‐soluble copolymers. I. Biodegradability and functionality of poly[(sodium acrylate)‐co‐(4‐vinylpyridine)]

As a biodegradable functional polymer, poly[(sodium acrylate)‐co‐(4‐vinylpyridine)] [P(SA‐co‐4VP)] containing a small amounts of 4‐vinylpyridine groups were prepared and their biodegradability, dispersity, and complex performance were analyzed. The polymers can be useful as detergent builders and dispersants. It was found that the biodegradation of P(SA‐co‐4VP) was more conspicuous when content of the 4‐vinylpyridine in the copolymer was larger. This indicates that the 4‐vinylpyridine, which acts as biodegradable segments, should be incorporated into the polymer main chain in such a manner that they are digested by activated sludge. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 71: 1953–1957, 1999     

Relation between microstructure and glass transition temperature of poly[(methyl methacrylate)‐co‐(ethyl acrylate)]

The glass transition temperature of a series of samples of the poly[(methyl methacrylate)‐co‐(ethyl acrylate)] copolymer, synthesized at low conversion, were calculated theoretically using the equations of Barton and Johnston. The values obtained are more precise when the probabilities of the compositional diads are derived from the ¹³C NMR data instead of the classical method utilizing reactivity ratios. This can be observed more clearly when the copolymer samples are synthesized at high conversion. Introduction of configuration (tacticity) at the diad level confirms the above observations and slightly improves the calculated values of T_g compared to the initial formulae which were only taking into account the compositional sequences of the copolymer. © 2001 Society of Chemical Industry     

Characterization of a novel bioactive poly[(lactic acid)‐co‐(glycolic acid)] and collagen hybrid matrix for dermal regeneration

Different strategies have been explored for the purpose of autologous or allogeneic dermal regeneration. We have developed a hybrid matrix by lyophilizing collagen within a poly[(lactic acid)‐co‐(glycolic acid)] (10:90, molar composition) knitted mesh, in order to assimilate the advantages of natural and synthetic materials. The porosity of the mesh was found to be almost 95 %, using Micro‐Computed Tomography Analysis, while the mechanical properties were comparable to native skin. In vitro biocompatibility was analyzed by culturing rat dermal fibroblasts in the matrices over 10 days. The cells were able to attach, proliferate and remain viable within the hybrid matrices. Subsequently, in vivo biocompatibility was analyzed by implanting the matrices subcutaneously in immunocompetent rats, for 2 weeks. Histological analysis showed that the poly[(lactic acid)‐co‐(glycolic acid)]–collagen hybrid matrices evoked minimal host tissue response in vivo. This study forms the basis of using poly[(lactic acid)‐co‐(glycolic acid)]–collagen hybrid matrices for our future work to develop a bioactive matrix for dermal regeneration. Copyright © 2005 Society of Chemical Industry     

Preparation of electrorheological active ionomers from poly(2‐hydroxyethyl methacrylate)‐co‐poly(4‐vinyl pyridine)

In this study, synthesis, characterization, partial hydrolysis, and salt formation of poly(2‐hydroxyethyl methacrylate)‐co‐poly(4‐vinyl pyridine), (poly(HEMA)‐co‐poly‐(4‐VP)) copolymers were investigated. The copolymers were synthesized by free radical polymerization using K₂S₂O₈ as an initiator. By varying the monomer/initiator ratio, chain lengths of the copolymers were changed. The copolymers were characterized by gel permeation chromatography (GPC), viscosity measurements, ¹H and ¹³C NMR and FTIR spectroscopies, elemental analysis, and end group analysis methods. The copolymers were partially hydrolyzed by p‐toluene sulfonic acid monohydrate (PTSA·H₂O) and washed with LiOH_(aq) solution to prepare electrorheological (ER) active ionomers, poly(Li‐HEMA)‐co‐poly(4‐VP). © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 99: 3540–3548, 2006     

Frequency and temperature dependence of poly(N‐isopropylacrylamide) gel rheology

Poly(N‐isopropylacrylamide) or p‐NIPAAM gels undergo a prominent deswelling transition near physiological temperatures. Using passive microrheology, we have investigated the viscoelastic response of p‐NIPAAM gels over a frequency range not accessible to bulk rheological measurements. Overall, NIPAAM gels moderately shear stiffen with increasing frequency. More intriguingly, sample viscosity rapidly declines with increasing frequency before leveling off near the solvent viscosity. The frequency for this crossover coincides with the emergence of fast gel modes seen in dynamic light scattering (DLS) from the gel. Furthermore, we monitored viscoelastic responses on approach to the deswelling transition. Intrinsic light scattering indicates that experimental conditions are not near the critical point and that the deswelling transition is second order in nature. Nevertheless, the corresponding elastic and viscous moduli of p‐NIPAAM displayed power‐law decreases with temperature. These changes with temperature were independent of probe frequency. Power law exponents, however, are sensitive to details of the sample preparation suggesting that these viscoelastic responses vary with gel structure. Correlating our microrheological measurements with DLS from the gel matrix itself, we find that several of the observed microrheological features are closely related to the intrinsic dynamics of the p‐NIPAAM gels. In particular, the transition from gel‐ to solvent dominated dissipation coincides with a transition from fast to slow gel modes. Combining microrheology with intrinsic light scattering, therefore, provides a compelling approach to probe rheological responses and correlate them to the underlying network dynamics. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci., 2013     

Tailoring the surface architecture of poly(3‐hydroxybutyrate‐co‐4‐hydroxybutyrate) scaffolds

This study was designed to determine whether the surface modifications of the various poly(3‐hydroxybutyrate‐co‐4‐hydroxybutyrate) [P(3HB‐co‐4HB)] copolymer scaffolds fabricated would enhance mouse fibroblast cells (L929) attachment and proliferation. The P(3HB‐co‐4HB) copolymer with a wide range of 4HB monomer composition (16–91 mol %) was synthesized by a local isolate Cupriavidus sp. USMAA1020 by employing the modified two‐stage cultivation and by varying the concentrations of 4HB precursors, namely γ‐butyrolactone and 1,4‐butanediol. Five different processing techniques were used in fabricating the P(3HB‐co‐4HB) copolymer scaffolds such as solvent casting, salt‐leaching, enzyme degradation, combining salt‐leaching with enzyme degradation, and electrospinning. The increase in 4HB composition lowered melting temperatures (T_m) but increased elongation to break. P(3HB‐co‐91 mol % 4HB) exhibited a melting point of 46°C and elongation to break of 380%. The atomic force analysis showed an increase in the average surface roughness as the 4HB monomer composition increased. The mouse fibroblasts (L929) cell attachment was found to increase with high 4HB monomer composition in copolymer scaffolds. These results illustrate the importance of a detailed characterization of surface architecture of scaffolds to provoke specific cellular responses. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Effects of Temperature and Surfactants on the Equilibrium Swelling Behavior of Poly[acrylamide‐co‐(itaconic acid)] Hydrogels

Summary: The swelling equilibrium of poly(acrylamide) [PAAm] and poly[acrylamide‐co‐(itaconic acid)] [P(AAm/IA)] hydrogels was studied as a function of temperature and IA content in aqueous solutions of surfactants: sodium dodecyl sulfate (SDS, anionic) and hexadecyltrimethylammonium bromide (HTAB, cationic). P(AAm/IA) hydrogels in water exhibited reentrant conformational transitions depending on temperature, whereas PAAm hydrogels were not affected with the change of temperature. The equilibrium‐volume‐swelling ratio of P(AAm/IA) hydrogels increased sharply in SDS solutions, with an increase of the mole percent of IA. However, in HTAB solution, the equilibrium‐volume‐swelling ratio of these hydrogels decreased with an increase of IA content.

The equilibrium volume‐swelling ratios of the hydrogels in water shown as a function of temperature.     

Synthesis and characterization of novel biodegradable poly(carbonate‐co‐phosphate)s

A series of aliphatic poly(carbonate‐co‐phosphate)s was synthesized in bulk using aluminium isopropoxide as initiator by ring‐opening polymerization with various cyclic carbonates (trimethylene carbonate (TMC) and 5,5‐dimethyltrimethylene carbonate (DTC)) and cyclic phosphates (ethylene ethyl phosphate (EEP), ethylene isobutyl phosphate (EIBP), ethylene lauryl phosphate (ELP) and ethylene stearyl phosphate (ESP)). The influence of reaction conditions such as polymerization time, polymerization temperature and initiator concentration on the yield and molecular weight were investigated. The substituent effect of the cyclic monomers on the polymerization was also studied, and the results indicate that the substituents exert a marked influence on the molecular weight of the copolymers obtained. The comonomer reactivity ratios were determined (TMC 0.88 and EEP 1.17). The copolymers with backbone chains rich in phosphate content exhibit better hydrophilicity than that of TMC homopolymer, and the degradation rate of the copolymers increases with the increase of phosphate content therein. © 2001 Society of Chemical Industry     

Preparation and swelling properties of solution crosslinked poly(cis‐1,4‐butadiene) gels

Poly(cis‐1,4‐butadiene) (PCB) gels were prepared by the crosslinking polymerization of 4‐tert‐butylstyrene (tBS) and divinylbenzene (DVB) onto unvulcanized butadiene rubber with a solution polymerization technique with benzoyl peroxide (BPO) as an initiator. The effects of the reaction conditions, such as the amount of the solvent, the amount of DVB and tBS, and the initiator (BPO), on the equilibrium swelling ratio (Q_e) were also investigated. The highest oil absorbencies of crosslinked gels in xylene and cyclohexane were 51.35 and 32.98 g/g, respectively. A swelling kinetic equation was proposed for this system: Q_t = Q_e ? {Kt + [1/(Q_e ? Q₀)]}^?1, where Q_t is the swelling ratio at time t, Q₀ is the initial swelling ratio, and K is the swelling kinetic constant. This equation fit the experimental results quite well. The diffusion of organic solvents in PCB gels was Fickian. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 2241–2245, 2003     

Synthesis and in vitro degradation properties of poly[(tetramethylene carbonate)‐co‐(sebacic anhydride)]

A novel poly[(tetramethylene carbonate)‐co‐(sebacic anhydride)] (PTCSA) was synthesized by the melt polycondensation reaction of sebacic acid (SA) and the dicarboxylic acid which derived from oligo(tetramethylene carbonate) diol via the corresponding mixed anhydrides. The copolymer structure was confirmed by means of FTIR and [¹H] NMR spectra. DSC analysis showed PTCSA was semicrystalline polymer which had low T_g (<?30 °C). The measurements of contact angles indicated that the hydrophobicity of PTCSA increased as the content of carbonate segments increased. In vitro degradation of PTCSA was performed in lipase‐free and lipase‐containing phosphate‐buffer saline (0.1 M, pH 7.4) at 37 °C. It was found that the degradation rate of PTCSA increased with the amount of SA. After 7 days of degradation in lipase‐free phosphate‐buffer saline, the weight loss of PTCSA was 74, 49 and 22% for 80, 58 and 32 mol% SA contained samples, respectively. The weight loss of PTCSA increased rapidly in the first week, then slowed down but could be greatly enhanced by lipase. After 3 weeks of degradation with or without lipase, the weight loss of PTCSA was 66 and 52% for 58 mol% SA‐containing samples, respectively. The size of the samples was gradually reduced and the surface became coarse. It was also found that the molecular weights of the outer layer were lower than those of the inner layer of the samples after degradation. The results suggested that PTCSA was some kind of biodegradation and surface‐erosion material. © 2001 Society of Chemical Industry     

Specific interactions in poly(styrene‐co‐2‐hydroxyethyl acrylate)/poly(styrene‐co‐N,N‐dimethylacrylamide) systems

Amphiphilic copolymers of poly(styrene‐co‐2‐hydroxyethyl acrylate) (SHEA) and poly(styrene‐co‐N, N‐dimethylacrylamide) (SAD) of different compositions were prepared by free radical copolymerization and characterized by different techniques. Depending on the nature of the solvent and the densities of interacting species incorporated within the polystyrene matrices, novel materials as blends or interpolymer complexes with properties different from those of their constituents were elaborated when these copolymers are mixed together. The specific interpolymer interactions of hydrogen bonding type and the phase behavior of the elaborated materials were investigated by differential scanning calorimetry (DSC) and Fourier transform infra red spectroscopy (FTIR). The specific interactions of hydrogen bonding type that occurred within the SHEA and within their blends with the SAD were evidenced by FTIR qualitatively by the appearance of a new band at 1626 cm^?1 and quantitatively using appropriate spectral curve fitting in the carbonyl and amide regions. The variation of the glass transition temperature with the blend composition behaved differently with the densities of interacting species. The thermal degradation behavior of the materials was studied by thermogravimetry. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Crosslinking of poly[(3‐hydroxybutyrate)‐co‐(3‐hydroxyvalerate)] using dicumyl peroxide as initiator

In order to modify poly [(3‐hydroxybutyrate)‐co‐(3‐hydroxyvalerate)] (PHBV), the crosslinking of this copolymer was carried out at 160 °C using dicumyl peroxide (DCP) as the initiator. The torque of the PHBV melt showed an abrupt upturn when DCP was added. Appropriate values for the gel fraction and crosslink density were obtained when the DCP content was up to 1 wt% of the PHBV. According to the NMR spectroscopic data, the location of the free radical reaction was determined to be at the tertiary carbons in the PHBV chains. The melting point, crystallization temperature and crystallinity of PHBV decreased significantly with increasing DCP content. The effect of crosslinking on the melt viscosity of PHBV was confirmed as being positive. Moreover, the mechanical properties of PHBV were improved by curing with DCP. When 1 wt% DCP was used, the ultimate elongation of PHBV increased from 4 to 11 %. A preliminary biodegradation study confirmed the total biodegradability of crosslinked PHBV. Copyright © 2004 Society of Chemical Industry     

Characterization of polyacrylonitrile,poly(acrylonitrile‐co‐vinyl acetate), and poly(acrylonitrile‐co‐itaconic acid) based activated carbon nanofibers

In this study, three different acrylonitrile (AN)‐based polymers, including polyacrylonitrile (PAN), poly(acrylonitrile‐co‐vinyl acetate) [P(AN‐co‐VAc)], and poly(acrylonitrile‐co‐itaconic acid) [P(AN‐co‐IA)], were used as precursors to synthesize activated carbon nanofibers (ACNFs). An electrospinning method was used to produce nanofibers. Oxidative stabilization, carbonization, and finally, activation through a specific heating regimen were applied to the electrospun fibers to produce ACNFs. Stabilization, carbonization, and activation were carried out at 230, 600, and 750 °C, respectively. Scanning electron microscopy, thermogravimetric analysis (TGA), and porosimetry were used to characterize the fibers in each step. According to the fiber diameter variation measurements, the pore extension procedure overcame the shrinkage of the fibers with copolymer precursors. However, the shrinkage process dominated the scene for the PAN homopolymer, and this led to an increase in the fiber diameter. The 328 m²/g Brunauer–Emmett–Teller surface area for ACNFs with PAN precursor were augmented to 614 and 564 m²/g for P(AN‐co‐VAc) and P(AN‐co‐IA), respectively. The TGA results show that the P(AN‐co‐IA)‐based ACNFs exhibited a higher thermal durability in comparison to the fibers of PAN and P(AN‐co‐VAc). The application of these copolymers instead of AN homopolymer enhanced the thermal stability and increased the surface area of the ACNFs even in low‐temperature carbonization and activation processes. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44381.     

Miscibility and crystallization kinetics of poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate)/ poly(methyl methacrylate) blends

The miscibility and crystallization kinetics of the blends of random poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) [P(HB‐co‐HV)] copolymer and poly(methyl methacrylate) (PMMA) were investigated by differential scanning calorimetry (DSC) and polarized optical microscopy (POM). It was found that P(HB‐co‐HV)/PMMA blends were miscible in the melt. Thus the single glass‐transition temperature (T_g) of the blends within the whole composition range suggests that P(HB‐co‐HV) and PMMA were totally miscible for the miscible blends. The equilibrium melting point (T°_m) of P(HB‐co‐HV) in the P(HB‐co‐HV)/PMMA blends decreased with increasing PMMA. The T°_m depression supports the miscibility of the blends. With respect to the results of crystallization kinetics, it was found that both the spherulitic growth rate and the overall crystallization rate decreased with the addition of PMMA. The kinetics retardation was attributed to the decrease in P(HB‐co‐HV) molecular mobility and dilution of P(HB‐co‐HV) concentration resulting from the addition of PMMA, which has a higher T_g. According to secondary nucleation theory, the kinetics of spherulitic crystallization of P(HB‐co‐HV) in the blends was analyzed in the studied temperature range. The crystallizations of P(HB‐co‐HV) in P(HB‐co‐HV)/PMMA blends were assigned to n = 4, regime III growth process. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 91: 3595–3603, 2004     

Miscibility and crystallization behavior of poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate)/poly(vinyl acetate) blends

The miscibility and crystallization behavior of poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) (P(HB‐co‐HV))/poly(vinyl acetate) (PVAc) blends have been investigated by differential scanning calorimetry (DSC) and polarized optical microscopy (POM). It was found that P(HB‐co‐HV)/PVAc blends were miscible in the melt over the whole compositions. Thus the blend exhibited a single glass transition temperature (T_g), which increased with increasing PVAc composition. The spherulitic morphologies of P(HB‐co‐HV)/PVAc blends indicated that the PVAc was predominantly segregated into P(HB‐co‐HV) interlamellar or interfibrillar regions during P(HB‐co‐HV) crystallization because of the volume‐filled spherulites. As to the crystallization kinetics study, it was found that the overall crystallization and crystal growth rates decreased with the addition of PVAc. The kinetics retardation was primarily attributed to the reduction of chain mobility and dilution of P(HB‐co‐HV) upon mixing with higher T_g PVAc. The overall crystallization rate was predominantly governed by the spherulitic growth rate and promoted by the samples treated with the quenched state because of the higher nucleation density. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 980–988, 2006     

Synthesis,properties and thermal stability of water‐soluble poly(potassium 1‐hydroxyacrylate‐co‐styrene) copolymer

The present work investigates the structure properties of copolymers using thermogravimetric analysis, hot stage microscopy, static light scattering, field emission scanning electron microscopy, X‐ray diffraction analysis and a Brookfield viscometer. Poly(potassium 1‐hydroxyacrylate) (PKHA) is a water‐soluble polymer. However, the copolymer of styrene and 2‐isopropyl‐5‐methylene‐1,3‐dioxolan‐4‐one is not water soluble at equal molar ratio because the polystyrene reduces the solubility. The effect of styrene on poly(potassium 1‐hydroxyacrylate‐co‐styrene) copolymer, i.e. poly(KHA‐co‐St), was investigated for the increasing solubility of the copolymer. The solubility was increased at a lower molar ratio of styrene such as 0.4 in the copolymer. It was found that the copolymer was soluble in water when a content ratio of 68/32 mol% of homopolymer was incorporated in poly(KHA₆₈‐co‐St₃₂) copolymer as determined by NMR analysis. Also the poly(KHA₆₈‐co‐St₃₂) copolymer was found to be salt tolerant, possessed water absorption capacity and was thermally stable up to 183 °C. Moreover, it is shown that the polystyrene content plays a key role in the thermal stability of the copolymer. © 2017 Society of Chemical Industry     

Surface‐active amphiphilic poly[(2‐acrylamido‐2‐methylpropanesulfonic acid)‐co‐(N‐isopropylacrylamide)] nanoparticles as stabilizer in aqueous emulsion polymerization

This work reports the effect of nanogel solid particles on the surface and interfacial tension of water/air and water/styrene interfaces. Moreover, the work aimed to use nanogels as a stabilizer for miniemulsion aqueous polymerization. A series of amphiphilic crosslinked N‐isopropylacrylamide (NIPAm) and 2‐acrylamido‐2‐methylpropanesulfonic acid (AMPS) copolymer nanogels were synthesized based on an aqueous copolymerization batch method. Divinylbenzene and N,N‐methylene bisacrylamide were used as crosslinkers. The morphologies of the prepared nanogels were investigated using transmission and scanning electron microscopies. The lower critical transition temperatures were determined using differential scanning calorimetry. The surface tension of colloidal NIPAm/AMPS dispersions was measured as functions of surface age, temperature and the morphology of the NIPAm/AMPS nanogels. The NIPAm/AMPS nanogels reduced the surface tension of water to about 30.1 mN m^?1 at 298 K with a small increase at 313 K. Surface activities of these nanogels in water were determined by surface tension measurements. The NIPAm/AMPS dispersions had high surface activity and were used as a stabilizer to prepare a crosslinked poly(styrene‐co‐AMPS) microgel based on emulsion crosslinking polymerization. © 2013 Society of Chemical Industry