共查询到19条相似文献,搜索用时 203 毫秒
1.
2.
3.
4.
6.
7.
坐标测量机对凸轮曲线的测量与拟合及其评价 总被引:3,自引:0,他引:3
坐标测量机测量凸轮时,确定工件坐标系是一大难题。文中提出一种方法,可以从凸轮任意位置开始检测。仅测量一次凸轮轮廓,所有的测量数据均用于建立被测凸轮的工件坐标系,并可使测量误差、形位误差对凸轮工件坐标系建立的影响降低至最小程度。此外还提出了一种修正开关式球测头半径的计量学方法。 相似文献
8.
9.
三坐标测量中工件坐标系的建立与分析 总被引:2,自引:0,他引:2
PC-DMIS软件编程中,工件坐标系建立的好坏直接影响测量精度和测量效率。文章结合工作实际,分析了批量工件和单一工件坐标系的建立方法。 相似文献
10.
许多精密仪器仪表零件上分布有相互位置关系的一组孔,如图1所示。手表主夹板就是集中孔组、位置精度要求高的典型零件,其上孔组的位置度测量是生产中的重要环节。目前,国内各表厂均用直角坐标系统的坐标显微镜或工具显微镜来测量其坐标位置误差,然后换算成位置度误差。测量时,通常选取两个孔作为定位基准孔,即定心孔和定向孔,这样就在测量系统中形成测量基准坐标系,使被测夹板定位。由于在实际加工中,夹板孔组中各孔包括定位孔本身的位置,不可避免地产生坐标误差,而作为定位孔的误差就会传播到各被测 相似文献
11.
Theodore H. Hopp Mark S. Levenson 《Journal of research of the National Institute of Standards and Technology》1995,100(5):563-574
The Algorithm Testing and Evaluation Program for Coordinate Measurement Systems (ATEP-CMS) is a Special Test Service offered under the NIST Calibration Program. ATEP-CMS evaluates the performance of geometric fitting software used in coordinate measurement systems. It is a Special Test because it is a new type of NIST service, experimental in nature and unsupported by historical data. This report documents and explains the rationale of the performance measures used in ATEP-CMS and analyzes the uncertainties of those measures. 相似文献
12.
13.
加工坐标系和涡旋体旋转坐标系偏差会引起较大的侧面啮合间隙,加工坐标系的在线调整能提高涡旋体加工精度.基于极坐标系开发了涡旋体侧面轮廓快速测量系统,可调对齐平台能精确确定测量坐标系原点.分析并去除了测量系统误差,通过涡旋体径向误差三维粒子群寻优计算,得到加工坐标系和涡旋体旋转坐标系的坐标偏差和旋转角度偏差.新的测量系统获得了同三坐标测量机(CMM)相同的测量结果,同时测量时间从20 min缩短为180 s,测量环境和测量时间能满足涡旋体在线加工补偿的要求. 相似文献
14.
15.
光学3D坐标测量技术研究 总被引:4,自引:0,他引:4
研究了光学坐标测量系统三维精密视觉测量方法,对其核心技术:数字成像器件模型及标定方法、辅助靶标技术以及高精度亚象素图像处理算法进行了深入的讨论,并提出了详细的解决方法.经实验证明,这些方法切实可行,达到了所要求的精度,从而为光学坐标测量系统的设计提供了可靠依据. 相似文献
16.
Precision measurement of complex surfaces requires intensive sampling for fully characterising the surface geometry and reducing the measurement uncertainty, which is, however, less efficient when the data are costly to acquire. This paper presents a Gaussian process (GP)-based intelligent sampling method for achieving well balance between the measurement efficiency and accuracy. The method makes use of GP to model the surface with domain-specific composite covariance kernel functions. The statistical nature of the GP makes it capable of giving credibility to the arbitrary prediction over the entire established model which can be used in a critical criterion to perform intelligent sampling of the surfaces. The method is independent from the coordinate frames, which makes the sampling plan easily utilised without accurate pre-positioning in actual measurement. The effectiveness of the method is verified through a series of comparison study and actual application in measuring a multi-scaled complex mould insert on coordinate measuring machine. 相似文献
17.
用三坐标实现圆柱齿轮的自动测量与评价 总被引:3,自引:0,他引:3
本文建立了一套三坐标机用于齿轮自动测量时离散采点的数学模型和误差评价模型。应用这套模型编制的自动测量软件可评价出齿形误差、齿向误差、周节累积误差及齿圈径向跳动误差等误差参数。在数据处理中,本文提出了数学软测头的概念,它对齿轮误差评价具有较高的应用价值。 相似文献
18.
19.
基于信标的摄影测量定位技术,提出了一种用于光电助降系统的双摄影测量算法.利用两台CCD 摄像机探测直升机两侧各四个信标,建立目标坐标系、摄像机坐标系和图像坐标系,根据信标、镜头中心和信标像点的共线性得到关于旋转矩阵和平移矢量的线性方程组,由此计算出直升机相对于着降点的位姿.设计了一套直升机光电助降实验系统,使用高性能DSP 系统进行实时图像处理,运用双摄影测量算法实时计算直升机着降引导信息.模拟实验结果表明,在两摄像机距离着降点8~13 m 范围内,光电助降实验系统的距离测量精度达到±5 cm,而角度测量精度达到±3°. 相似文献