Determination of consolidation behaviour of clay slurries

The main objective of this study was to determine the consolidation behaviour of clay slurries.A finegrained clay with high consistency limits(W_L = 180%,w_P= 120%) was investigated using conventional oedometer and bench-top centrifuge tests.Results indicated that the slurry had an apparent preconsolidation(due to initial conditions,electrochemical interactions,tortuous drainage,and thixotropic strength) from e = 5.7 to e = 5.5 followed by virgin compression.Likewise,the low hydraulic conductivity(10~(-10)-10~(-12) m/s) was due to low porosity(small pore throats) and high tortuosity(long flow paths).Unlike consolidation of soils,the c_v and m_v decreased with increasing σ' but increased with increasing e and k.The data from the two tests correlated well in the range of σ' = 10-65 kPa,e = 5.5-3.86,k= 1.7 × 10~(-10)-5×10~(-11) m/s,F_c = 1-40 MN.New equations were developed to correlate the consolidation parameters(e,σ',k) with F_c.The deviation of k beyond 40 MN(e = 4.65) was due to deviation from the initial straight line portion of the settlement curve in the centrifuge test.     

Geotechnical behavior of uranium mill tailings from Saskatchewan,Canada

This paper investigates the geotechnical behavior of uranium mill tailings from Saskatchewan, Canada.The 4% tailings were well-graded with 29% fines whereas the 5% and 6% tailings were gap-graded with 49% fines. All samples exhibited a negligible strength(0.4 k Pa) up to 60% solids, followed by a rapid increase. The 4% tailings exhibited a lower rate and amount of settlement than 5% and 6% tailings. The kidecreased from 10~(-2)to 10~(-4)m/s with a decrease in eifrom 16 to 4 and a decrease in ef from 8 to 4 such that 4% tailings showed one order of magnitude lower values than the 5% and 6%tailings. The settling potential decreased ten times(50%–5%) for 4% tailings and four times(60%–15%)for 5% and 6% tailings. The effective stress increased from 80 to 260 Pa in the settling tests. The 4%tailings were less prone to segregation when compared with 5% and 6% tailings. The average solids content after settling was 35% for 4% tailings, 40% for 5% tailings and 39% for 6% tailings with a solids content deviation of ±3%, ±8%, ±6%, respectively. All materials were essentially non-segregating at 40%initial solids.     

Pore structure characteristics of the relative water-resisting layer on the top of the Ordovician in Longgu Coal Mine

In order to study the permeability and water-resisting ability of the strata on the top of the Ordovician in Longgu Coal Mine, this paper tested the permeability and porosity of the strata, investigated the fracture and pore structure features of the strata, and identified the main channels which govern the permeability and water-resisting ability of the strata. The permeability of the upper, central and lower strata shows as 2.0504 × 10⁻³–2.782762 × 10⁻³, 4.1092 × 10⁻³–7.3387 × 10⁻³ and 2.0891 × 10⁻³–3.2705 × 10⁻³ μm², respectively, and porosity of that is 0.6786–0.9197%, 0.3109–0.3951% and 0.9829–1.8655%, respectively. The results indicate that: (1) the main channels of the relative water-resisting layer are the pore throats with a diameter more than 6 μm; (2) the major proportion of pore throats in the vertical flow channel and the permeability first increases and then sharply decreases; (3) the fractures occurring from the top to 20 m in depth of the strata were filled and there occurred almost no fracture under the depth of 40 m; and (4) the ratio of turning point of the main flow channel in the strata on top of Ordovician can be used to confirm the thickness of filled water-resisting layers.     

Preconcentration of rare earth elements from Iranian monazite ore by spiral separator using multi-response optimization method

The present work dealt with the preconcentration of rare earth elements in Saghand ore (Yazd province, Iran) which was achieved by Humphrey spiral using orthogonal optimization method after scrubbing the sample at 45% solid pulp density for 30 min. The pulp was diluted and was fed to a Humphrey spiral for upgrading. The process parameters considered were feed size, feed solids and feed rate, and Taguchi’s L₉ (3⁴) orthogonal array (OA) was selected for optimization of the process. The results show that the feed rate and feed size were more significant than the other operation parameters of the process. It was also found that under optimal conditions, the concentrate grade of rare earth elements increased from 2860 × 10⁻⁶ to 6050 × 10⁻⁶ and recovery reached to 58%.     

Effect of agitation on the characteristics of air dense medium fluidization

In order to study the effect of agitation on the characteristics of air dense medium fluidization, we designed and constructed an agitation device. Analyses were then conducted on the fluidization characteristics curves, the bed density stability and the average bubble rise velocity Uaunder different agitation conditions. The results indicated that a lower bed pressure drop(without considering lower gas velocity in a fixed bed stage) and higher minimum fluidized velocity are achieved with increasing agitation speed.The height d(distance between the lower blades and air distribution plate) at which the agitation paddle was located had a considerable effect on the stability of the bed density at 9.36 cm/s U 10.70 cm/s. The higher the value of d, the better the stability, and the standard deviation of the bed density fluctuation r dropped to 0.0364 g/cm~3 at the ideal condition of d = 40 mm. The agitation speed also had a significant influence on the fluidization performance, and r was only 0.0286 g/cm~3 at an agitation speed of N = 75 r/min. The average bubble rise velocity decreased significantly with increasing agitation speed under the operating condition of 1.50 cm/s U–U_(mf) 3.50 cm/s. This shows that appropriate agitation contributes to a significant improvement in the fluidization quality in a fluidized bed, and enhances the separation performance of a fluidized bed.     

Surface magnetization of siderite mineral

Surface self-magnetization of siderite is achieved by generating ferromagnetic substance on the surface of siderite by adjusting slurry temperature, pH value, stirring rate and reaction time. No addition of any iron-containing reagent is required. The temperature of 60 °C, NaOH concentration of 0.10 mol/L; stirring rate of 900 r/min and the reaction time of 10 min are the optimal conditions. The results show that the siderite recovery in magnetic separation increased from 26.9% to 88.8% after surface magnetization. Magnetization kinetic equation is expressed as 1 ? [1 ? (? ? 0.269)]^1/3 = Kt. Activation energy for the magnetization reaction is 4.30 kJ/mol. VSM, SEM and XPS were used to characterize the siderite, and results show that the saturated magnetization (σ_s) of siderite increased from 0.652 to 2.569 A m²/kg, the magnetic hysteresis was detected with a coercive force of 0.976 A/m after magnetization; Fe2P3/2 electron binding energy changed which reflects the valence alteration in iron on the surface and the formation of ferromagnetic Fe₃O₄.     

Leaching kinetics in cyanide media of Ag contained in the industrial mining-metallurgical wastes in the state of Hidalgo,Mexico

The leaching kinetics in cyanide media of the silver contained in the Dos Carlos waste tailings at the City of Pachuca de Soto, Hidalgo State, Mexico were carried out. The used material contained the following chemical composition: 56 × 10^-6 of Ag, 0.6 × 10⁻⁶ of Au and 70.43% (by weight) of SiO₂; 7.032% (by weight) of Al₂O₃; 2.69% (by weight) of Fe; 0.46% (by weight) of Mn; 3.98% (by weight) of K₂O; 3.34% (by weight) of CaO; 2.50% (by weight) of Na₂O; 0.04% (by weight) of Zn; 0.026% (by weight) of Pb. The mineralogical phases present were the following: Silica, albite, argentite, berlinite, orthoclase, potassium jarosite, and natrojarosite. In the leaching kinetics in cyanide media, and under the studied conditions, the effect of the CN⁻ concentration on the reaction rate has no effect on the whole process of alkaline cyanidation, of which the reaction order is n ≈ 0. Temperature has an effect on the cyanidation rate of the reaction, with an activation energy of 47.9 KJ/mol. At the same time, when the particle size decreases there is an increase in the reaction rate, which is inversely proportional to the particle diameter; when increasing the NaOH concentration there is an increase in the reaction rate K_exp, with a reaction order (n) of 0.215 under the studied ranges.     

Artificial neural network approach for rheological characteristics of coal-water slurry using microwave pre-treatment

Detailed experimental investigations were carried out for microwave pre-treatment of high ash Indian coal at high power level(900 W) in microwave oven. The microwave exposure times were fixed at60 s and 120 s. A rheology characteristic for microwave pre-treatment of coal-water slurry(CWS) was performed in an online Bohlin viscometer. The non-Newtonian character of the slurry follows the rheological model of Ostwald de Waele. The values of n and k vary from 0.31 to 0.64 and 0.19 to 0.81 Pa·sn,respectively. This paper presents an artificial neural network(ANN) model to predict the effects of operational parameters on apparent viscosity of CWS. A 4-2-1 topology with Levenberg-Marquardt training algorithm(trainlm) was selected as the controlled ANN. Mean squared error(MSE) of 0.002 and coefficient of multiple determinations(R~2) of 0.99 were obtained for the outperforming model. The promising values of correlation coefficient further confirm the robustness and satisfactory performance of the proposed ANN model.     

Long-term economic sensitivity analysis of light duty underground mining vehicles by power source

LHD's are expensive vehicles; therefore, it is important to accurately define the financial consequences associated with the investment of purchasing the mining equipment. This study concentrates on longterm incremental and sensitivity analysis to determine whether it is feasible to incorporate current battery technology into these machines. When revenue was taken into account, decreasing the amount of haulage in battery operated equipment by 5% or 200 kg per h amounts to a $4.0 × 10~4 loss of profit per year. On average it was found that using battery operated equipment generated $9.5 × 10~4 more in income annually, reducing the payback period from seven to two years to pay back the additional $1.0 × 10~5 investment of buying battery powered equipment over cheaper diesel equipment. Due to the estimated 5% increase in capital, it was observed that electric vehicles must possess a lifetime that is a minimum of one year longer than that of diesel equipment.     

Strength behaviour of sandstone subjected to polyaxial state of stress

The paper presents an experimental investigation on the strength behaviour of natural rock subjected to polyaxial state of stress. The polyaxial tests were conducted on cubical specimens of sandstone obtained from the Shivpuri district in Madhya Pradesh state of India, The specimens having nominal dimensions of100 mm x 100 mm x 100 mm were tested using a polyaxial testing machine. Twenty-five combinations of intermediate and minor principal stresses were applied and the specimens were loaded till failure occurs. It was observed that the intermediate principal stress has a substantial effect on the strength of the Shivpuri sandstone. A database of rock strength under various combinations of σ_2 and σ_3 was obtained for the Shivpuri sandstone. The database was used to study the predictability of five most commonly used strength criterion. Root mean square error(RMSE), average absolute relative error percentage(AAREP) and coefficient of accordance(COA) were used as indices for the measure of goodness of fit. It was observed that the least error in the prediction was shown by modified Mohr Coulomb criterion followed by modified Weibols and Cook criterion. A probability analysis of the error in prediction was also done.     

Reservoir characteristics of Donghe well No.1 in Tarim Basin

Based on the techniques of X-ray diffraction analysis, identification of the thin sections of core cast, physical analysis and scanning electron microscopy analysis, this paper studied the reservoir characteristics of the Carboniferous strata in Donghe well No.1 of Tarim region. The results show that the reservoir lithology is mainly the fine-grained quartz sandstone with ferrocalcite and pyrite, mud cement-based, the permeability concentrated in 5–40 × 10–3 μm², a small part of the high permeability up to 150–327 × 10⁻³ μm² and porosity ranged from 10% to 20%. The most part of the reservoirs is low permeability with a small part of the layer in moderate-high permeability. The types of reservoir space include intergranular pores, intra particle-molding pores, micro-pores and cracks, which mainly are intergranular pores with the pore diameter of 15–200 μm, 95.5 μm on average. And the types of the throats are complex with the main type of constricted throats in this area and large contribution to the permeability.     

Effective goaf gas capture design at Ravensworth Underground Mine

This paper highlights a reliable goaf gas capture system developed and used at Ravensworth Underground Mine since its trial in 2009. The method utilises horizontal holes drilled from underground sites and connected to an underground gas pipeline. This system incorporates a gas suction and flaring plant designed specifically for this method. The current method has captured effectively a total longwall, and adjacent goaf gas accounts for over 85%. The design of the holes drilled has been the success of the gas flow reliability. The flow is extraordinarily consistent and predictable. The management of the underground pipeline determines the overall reliability of flow. The design has resulted in Ravensworth Management being confident to remove a gas bearing bleeder roadway and still manage the existing tailgate roadway for allowing access as required. The reduction of CO₂ equivalent emissions recorded is approximately 0.35 × 10⁶ tons annually. This design has further improvements to be added to allow use at any other site with gas in the overlying strata.     

Removal and utilization of calcite existed in scheelite by preparation of calcium sulfate whiskers

In order to eliminate the effect of calcite associated with scheelite on the scheelite flotation, hydrochloric acid was used to dissolve the calcite, and the soaking solution was used to prepare CaSO_4 whiskers by hydrothermal reaction with sulfuric acid at ambient pressure. First, the condition experiments of preparing CaSO_4 whiskers by using CaCl_2 and H_2SO_4 were carried out to optimize reaction parameters of the crystallization process. The optimal conditions were: at 102 ℃ reaction temperature, 0,5 mol/L reactant concentration and 60 min reaction time. Then based on the condition experiments and considering keeping acid concentration stable for achieving HCl recycling, Calcium sulfate whiskers with the average diameter of 1.41 μm and the average aspect ratio of 109 were prepared by the soaking solution after evaporating to half of its volume and 1.0 mol/L H_2SO_4 at 102 ℃ for 60 min: After ion exchange processing,the filtrate could be used as HCl in the process of HCl dissolution.     

Signal characteristics of coal and rock dynamics with micro-seismic monitoring technique

In this study,differences of signal characteristics between mine shocks and coal and gas outbursts in coal mines were examined with the micro-seismic monitoring technique and time–frequency analysis.The duration of the mine shock is short while the coal and gas outburst lasts longer.The outburst consists of three stages:the pre-shock,secondary shock and main shock stage,respectively.The velocity amplitude of the mine shock is between 10~(-)5and 10~(-3)m/s,which is higher than that of the outburst with the same energy level.In addition,in both cases,the correlation between the velocity amplitude and energy is positive while the correlation between the signal frequency band distribution and energy is negative.The signal frequency band of the high energy mine shock is distributed between 0 and 50 Hz,and the low energy mine shock is between 50 and 100 Hz.The fractal characteristics of mine shocks were studied based on a fractal theory.The box dimensions of high energy mine shocks are lower than the low energy ones,however,the box dimensions of outbursts are higher than that of mine shocks with the same energy level.The higher box dimensions indicate more dangerous dynamic events.     

Discontinuities effect on drilling condition and performance of selected rocks in Nigeria

The study examined joint discontinuity spacing effect on drilling condition and performance in selected rocks in Ilorin and Ibese areas, Nigeria. Five samples for each rock type (gneiss and limestone) were tested in the laboratory for chemical, physical and mechanical properties. Dip direction and joint spacing were measured using compass clinometers. The chemical composition was determined using X-ray Fluorescence (XRF) spectrometer. The results show that gneiss has SiO₂ of 61.88% and limestone has CaO content of 52.3%. The average dry density of gneiss and limestone are 2.6 and 2.39 g/cm³, respectively. The uniaxial compressive strength of gneiss and limestone are 195 and 93.83 MPa, respectively. These rocks are classified as strong and moderately strong rock. Gneiss and limestone have mean joint discontinuity spacing of 0.79 and 0.25 m, which classified them as moderate and wide joint spacing respectively. Joint spacing was correlated with specific energy, bit wear and uniaxial compressive using Statistical Package for Social Science (SPSS). The regression model has multiple coefficient of correlation of R² = 0.791 and R² = 0.995 for gneiss and limestone, respectively. The variation in joint spacing could be attributed to specific energy, bit wear and uniaxial compressive strength which affect drilling condition and performance. Ultimately, as joint spacing gets closer, the drilling velocity increases, drill string will be stable.     

Non-Darcy flow seepage characteristics of saturated broken rocks under compression with lateral constraint

sing an MTS816.03 test system and self-designed seepage apparatus,seepage tests of saturated broken rocks were conducted,and the influence of lithology,axial stress,grain size distribution and loading rate on seepage characteristics was analyzed.The results show that:(1) Under the same axial stress(12 MPa)the permeability of different lithologic samples increases in the order:gangue mudstone sand stone limestone.The permeability of gangue is 3 magnitudes lower than that of limestone.The absolute value of the non-Darcy coefficient β increases in the order:limestone sandstone mudstone gangue The non-Darcy coefficient β of limestone,which is positive,is 5 magnitudes lower than that of gangue.(2)With increasing axial stress,the permeability of saturated broken sandstone decreases,and the absolute value of the non-Darcy coefficient β increases.After the axial stress exceeds 12 MPa,the curves of perme ability and non-Darcy coefficient β all tend to be stable.(3) With increasing Talbol power exponent,the permeability increases,and the absolute value of the non-Darcy coefficient β decreases.(4) With increas ing loading,the permeability increases,and the absolute value of the non-Darcy coefficient β decreases When the loading rate is 0.5 kN/s,the non-Darcy coefficient β is positive.     

Identification of large-scale goaf instability in underground mine using particle swarm optimization and support vector machine

An approach which combines particle swarm optimization and support vector machine (PSO–SVM) is proposed to forecast large-scale goaf instability (LSGI). Firstly, influencing factors of goaf safety are analyzed, and following parameters were selected as evaluation indexes in the LSGI: uniaxial compressive strength (UCS) of rock, elastic modulus (E) of rock, rock quality designation (RQD), area ration of pillar (S_p), the ratio of width to height of the pillar (w/h), depth of ore body (H), volume of goaf (V), dip of ore body (α) and area of goaf (S_g). Then LSGI forecasting model by PSO-SVM was established according to the influencing factors. The performance of hybrid model (PSO + SVM = PSO–SVM) has been compared with the grid search method of support vector machine (GSM–SVM) model. The actual data of 40 goafs are applied to research the forecasting ability of the proposed method, and two cases of underground mine are also validated by the proposed model. The results indicated that the heuristic algorithm of PSO can speed up the SVM parameter optimization search, and the predictive ability of the PSO–SVM model with the RBF kernel function is acceptable and robust, which might hold a high potential to become a useful tool in goaf risky prediction research.     

Moment tensor analysis of transversely isotropic shale based on the discrete element method

In this study,the moment tensor of transversely isotropic shale was analyzed using a discrete element method-acoustic emission model(DEM-AE model).Firstly,the failure modes of the shale obtained from the acoustic emission(AE) events and physical experiments were compared.Secondly,the relationships between AE events and seismic magnitudes,and AE events and the resulting cracks were analyzed.Finally,a moment tensor T-k chart describing the seismic source was introduced to demonstrate the differences in the transversely isotropic shale.The results showed that,for different anisotropy angles,a linear logarithmic relationship existed between the cumulative AE events and the seismic magnitude in the concentration area of the AE events.A normal distribution was observed for the number of AE events as the seismic magnitude changed from small to large.The moment tensor T-k chart indicated that the number and proportion of linear tension cracks in the shale were highest.When θ = 30°,the peak seismic magnitude was at a minimum.The average seismic magnitude in the concentration area of the AE events was also relatively small.Points close to the U=-1/3V line and the number of cracks included in a single AE event were at a minimum,and the corresponding peak stress also reached its lowest level.In contrast,when θ=90°,all related parameters were contrary to the above θ = 30° case.The DEM-AE model and the moment tensor T-k chart are suitable for analyzing the distribution of shale cracks appearing during the loading process.This study can provide constructive references for future research on the fracturing treatment of shale.     

Determining the rational layout parameters of the lateral high drainage roadway serving for two adjacent working faces

To determine the rational layout parameters of the lateral high drainage roadway(LHDR) serving for two adjacent working faces, a mechanical model of the LHDR under mining influence was established, and the overburden fissure, mining-induced stress distribution rules were analyzed. First, the development characteristics of mining-induced overburden fissure and the stress distribution law of the upper section of the working face were analyzed. Second, by analyzing the distribution law of vertical stress at different layers, the lateral distance of the LHDR was determined as 25 m. Third, by analyzing the surrounding rock deformation effect, stress distribution law, and overburden fissure distribution law of the LHDR at the heights of 20, 25, and 30 m away from the roof, the rational horizon of the LHDR was determined to be 25 m. Finally, an example of a LHDR located 25 m above the roof of the No. 2 coal seam and 25 m away from the No. 2-603 working face was presented. Results show that when the No. 2-603 coalface is being mined, the surrounding rocks lag 80 m or even further and the working face tends to be stable. The relative deformations of the roof and floor of the roadway and both of its walls were 583 and 450 mm,respectively. The reduction rate of the roadway section was 21.52%–25.32%. The section of the roadway was sufficient to extract the pressure relief gas in the overburden of the No. 2-605 working face. The average gas concentration and the pure volume at the branch pipeline were 24.8% and 22.3 m~3/min,respectively, showing that the position of high-level boreholes was reasonable.     

Constitutive model for methane desorption and diffusion based on pore structure differences between soft and hard coal

This paper aims to improve the accuracy and applicability of gas diffusion mathematical models from coal particles. Firstly, a new constitutive model for gas diffusion from coal particles with tri-disperse pore structure is constructed by considering the difference in characteristics between soft coal and hard coal.The analytical solution is then derived, that is, the quantitative relationship between gas diffusion rate(Qt/Q_∞) and diffusion time(t), The pore structure parameters of soft coal and hard coal from Juji coal mine are determined. Gas diffusion rules are numerically calculated and investigated by physical simulation methods. Lastly, the applicability of this model is verified. The results show that the homogeneous model only applies to the gas diffusion process of hard coal during the initial 10 min. The calculation results from this model and the physical experimental results of soft coal and hard coal are nearly identical during the initial 30 min.