Study of AC electrical properties of V2O5–P2O5–B2O3–Dy2O3 glasses

The AC conductivity of glass samples of composition 60V₂O₅–5P₂O₅–(35−x)B₂O₃–xDy₂O₃, 0.4≤x≤1.2 has been analyzed. The samples were prepared by the usual melt-quench technique. The prepared compounds were analyzed by X-ray diffraction (XRD) and thermo gravimetric–differential thermal analysis (TG/DTA). The activation energies were evaluated using glass transition temperature (T_g) and peak temperature of crystallization (T_c) from TG/DTA. The dependence of activation energy on composition was discussed. The electrical conductance and capacitance were measured over a frequency range of 20 Hz to 1 MHz and a temperature range of 303–473 K; these reveal semiconducting features based predominantly on an ionic mechanism. The dielectric and complex-impedance response of the sample is discussed. The relaxation time was found to increase with increasing temperature. Jonscher's universal power law is applied to discuss the conductivity. The electrode polarization was found to be negligible and confirmed from electrical modulus.     

Crystallographic characterization of silicon nitride ceramics sintered with Y2O3–Al2O3 or E2O3–Al2O3 additions

Silicon nitride ceramics were sintered using Y₂O₃–Al₂O₃ or E₂O₃–Al₂O₃ (E₂O₃ denotes a mixed oxide of Y₂O₃ and rare-earth oxides) as sintering additives. The intergranular phases formed after sintering was investigated using high-resolution X-ray diffraction (HRXRD). The use of synchrotron radiation enabled high angular resolution and a high signal to background ratio. Besides the appearance of β-Si₃N₄ phase the intergranular phases Y₃Al₅O₁₂ (YAG) and Y₂SiO₅ were identified in both samples. The refinement of the structural parameters by the Rietveld method indicated similar crystalline structure of β-Si₃N₄ for both systems used as sintering additive. On the other hand, the intergranular phases Y₃Al₅O₁₂ and Y₂SiO₅ shown a decrease of the lattice parameters, when E₂O₃ was used as additive, indicating the formation of solid solutions of E₃Al₅O₁₂ and E₂SiO₅, respectively.     

Fe2O3/Ni2O3/Al2O3催化剂制备及其催化氧化靛蓝废水研究

以三氧化二铝为载体,采用浸渍沉淀法制备系列Fe2O3/Ni2O3/Al2O3催化剂。采用TG-DTA,XRD及ESEM等技术对催化剂进行表征,确定催化剂的最佳焙烧温度为460℃。以次氯酸钠为氧化剂,同时考察m(三氧化二镍)/m(三氧化二铝)、m(三氧化二铁)/m(三氧化二镍)、m(次氯酸钠)∶m(靛蓝废水)、pH对印染靛蓝废水处理的影响。结果表明:m(三氧化二镍)/m(三氧化二铝)=0.3,m(三氧化二铁)/m(三氧化二镍)=0.04,m(次氯酸钠)∶m(靛蓝废水)=1∶11,pH=7,反应温度为20℃,常压反应时间为2 h时,COD的去除率为95.3%。     

Al2O3/Fe2O3吸附剂脱除硫化氢的性能

采用共沉淀法制备了氧化铝改性的氧化铁吸附剂,并采用比表面积(BET)、X射线衍射(XRD)技术对吸附剂进行了表征。在固定吸附床上,考察了制备条件及吸附条件对吸附剂脱除硫化氢性能的影响。结果表明,引入氧化铝能显著提高氧化铁对硫化氢的吸附净化能力。氧化铁与氧化铝质量比为1∶0.5,造孔剂十六烷基三甲基溴化铵(CTAB)质量分数为2%,焙烧温度500℃时,采用共沉淀法的负载氧化铝吸附剂的吸附效果最好。在气速20 mL/min,吸附温度80℃时,脱硫率和穿透硫容可分别达到99.3%和105 mg/g,其穿透硫容比未经改性的活性氧化铁提高了49.8 mg/g。     

V2O5、NiO、Fe2O3和钒渣对Al2O3/MgAl2O4的腐蚀机理

研究了V2O5、NiO、Fe2O3和钒渣对Al2O3和MgAl2O4尖晶石的腐蚀。把Al2O3和MgAl2O4试样分别同上述氧化物一起从室温加热到1 400℃、1 450℃和1 500℃,加热速率为10℃.min-1。用XRD和SEM对每个系统的腐蚀机理进行了分析。结果显示,所研究的氧化物对Al2O3的影响弱于对MgAl2O4的影响。氧化铝被NiO侵蚀形成NiAl2O4尖晶石,MgAl2O4尖晶石被V2O5侵蚀形成MgV2O6。本文还观察到钒渣中的成分Fe2O3、Mg、Ni、V和Fe分散到了Al2O3结构中。另一方面,Fe2O3、Ca、S、Si、Na、Mg、V和Fe分散到了MgAl2O4结构中。最后,把得到的结果与FactSage软件的预测结果进行了对比。     

Influences of La and Er on structure and properties of Bi2O3–B2O3 glass

Bi₂O₃·2B₂O₃ glasses doped with La₂O₃ and Er₂O₃ were prepared by the melting-quenching method with AR-grade oxides. IR analysis was used to investigate the glass network structure. The characteristic temperatures including the glass transition temperature (T_g), crystallization temperature (T_p), and melting temperature (T_m) were estimated by DSC. The coefficient of thermal expansion (α), mass density (D), and Vickers hardness (H_v) were also measured. The results show that the basic network structure of Bi₂O₃·2B₂O₃ glasses doped with rare-earth oxides consists of chains composed of [BO₃], [BO₄], and [BiO₆] units. La₂O₃ and Er₂O₃ act as network modifiers. As the doping concentrations of the rare-earth oxides were increased, T_g increased and α decreased, indicating that a more rigid glass was obtained. Er₂O₃ reduces the melting temperature and prevents glass crystallization. La₂O₃ contributes to the improvement of the microhardness of Bi₂O₃·2B₂O₃ glass.     

The influence of In2O3 on electrical characteristics of iron mixed Li2O–PbO–B2O3–SiO2–Bi2O3 multi-component glass system

Glasses of the composition 19Li₂O–20PbO–20B₂O₃–30SiO₂–(10−x) Bi₂O₃–1Fe₂O₃: xIn₂O₃ with six values of x (0 to 5.0) were synthesized. Dielectric properties viz., dielectric constant, ε′(ω), loss, tan δ, ac conductivity, σ_ac, electric modulus, M(ω) over wide ranges of frequency and temperature and also dielectric break down strength have been studied as a function of In₂O₃ concentration. The temperature dispersion of real part of dielectric constant, ε′(ω) has been analyzed using space charge polarization model. The dielectric loss (and also the electric moduli) variation with frequency and temperature exhibited relaxation effects and these effects were attributed to the divalent iron ion complexes. The ac conductivity exhibited maximal effect, whereas the activation energy for the conductivity demonstrated minimal magnitude at about 1.0 mol% of In₂O₃. The conductivity mechanism is understood due to the polaronic transfer between Fe²⁺ and Fe³⁺ ions. The low temperature ac conductivity mechanism is explained following the quantum mechanical tunneling model. Spectroscopic studies viz., optical absorption and ESR spectra have revealed that the redox ratio (Fe²⁺/Fe³⁺) is maximal when the concentration of In₂O₃ is ~1.0 mol%. The higher values of dielectric parameters observed at 1.0 mol% of In₂O₃ are attributed to the presence of iron ions largely in divalent state and act as modifiers. The analysis of these results together with spectroscopic studies has indicated that when In₂O₃ is present in the glass matrix in higher concentrations (more than 1.0 mol%) iron ions predominantly exist in trivalent state, occupy substitutional positions and make the glass more rigid. Such enhanced rigidity of the network is causing the decrease of dielectric parameters with the concentration of In₂O₃. Finally it is concluded that In₂O₃ mostly participate in the glass network in octahedral positions and make act as reducing agent (for iron ions) in the studied glass matrix when its concentration is ≤1.0 mol%.     

Multiferroic ceramics in BaO–Y2O3–Fe2O3–Nb2O5 system

Multiferroic ceramics in BaO–Y₂O₃–Fe₂O₃–Nb₂O₅ system were synthesized and their dielectric, ferroelectric and magnetic properties were evaluated. XRD results showed that the ceramic composite consists of a major phase of tetragonal tungsten bronze structured Ba₂YFeNb₄O₁₅, and minor phases of monoclinic YNbO₄ and hexagonal Ba₃Fe₂Nb₆O₂₁. Three dielectric relaxations were observed in the temperature range from 125 to 575 K. The relaxor dielectric behavior in the temperature range from 125 to 350 K was attributed to the random occupation of Fe³⁺ and Nb⁵⁺ ions at B site of the tungsten bronze structure. The electrode polarization and the inhomogeneous structure contributed to the high-temperature and middle-temperature dielectric relaxations, respectively. Both the ferroelectric hysteresis loop and the magnetic hysteresis loop were measured, which suggested that the synthesized ceramic composite was a promising candidate of multiferroics.     

基于Fe2O3的片状α-Al2O3包覆研究

首先以片状α-Al₂O₃为基质,以Fe Cl₃为铁源,采用液相沉积法制备了Fe₂O₃/α-Al₂O₃珠光颜料,并借助SEM、EDS、XRD等手段对制备的珠光颜料进行性能表征,考察了反应p H值、反应温度、铁盐浓度、添加剂用量等因素对片状α-Al₂O₃包覆率的影响,得到了制备铁系包覆片状α-Al₂O₃的最佳制备工艺参数,同时了解了各参数影响包覆率的主次顺序,并在此基础上着重探讨了六偏磷酸钠对包覆率产生影响的机理。结果表明：影响包覆率的主次顺序依次为反应p H值、反应温度、添加剂用量、铁盐浓度;在最优的工艺参数下制备出来Fe₂O₃/α-Al₂O₃的包覆率为20.93%;样品的表面形貌光滑平整且包覆完整。     

Physical properties of pseudo quaternary Na2B4O7 – SiO2 – MoO3 – Dy2O3 glasses

Pseudo quaternary Na₂B₄O₇–SiO₂–MoO₃–Dy₂O₃ glasses with various concentrations of Dy₂O₃ were synthesized and characterized by ultrasound, DTA and X-ray diffraction (XRD). It was found that, the density, the molar volume and the elastic moduli increased while the ultrasonic velocities and the packing density decreased with increasing of Dy₂O₃ concentration. The lower values of the radii and the bond length of B₂O₃, compared to those of Dy₂O₃, decreased the interatomic forces between the reactant glass forming cations and oxygens inside the glassy network. Accordingly, this will increase the molar volume and in the same time will decrease the average cross-link density, the ultrasonic velocities, the glass transition temperature and the thermal stability. Also, this may result in a high density glass sample which will increase the elastic moduli. Based on Lasocka's model, a good correlation between the temperature of both glass transition ($T_{\mathit{gl}}$) and crystallization peak ($T_{\mathit{pc}})$was observed.     

Al2O3-3Al2O3·2SiO2-ZrO2耐火材料的相组成

Al2O3-SiO2-ZrO2系耐火材料应用范围广,特别被用作陶瓷辊,具有力学强度高、抗热震性能优良、耐碱类化合物侵蚀和高温蠕变率低的特性。Al2O3-SiO2-ZrO2系耐火材料性能很大程度上取决于其结晶相和玻璃相的总量和化学成分,采用定量XRPD和XRF研究了原料中Al2O3/SiO2比和氧化铝颗粒尺寸分布对结晶相和玻璃相的总量及其化学成分的影响。耐火材料由莫来石、刚玉、ZrO2的多晶体和总量各异的玻璃相组成。莫来石含量及其晶胞参数和成分随烧成温度改变,但主要受原料中Al2O3/SiO2比的影响。     

Bi2O3对K2O–B2O3–SrO–Al2O3–Nb2O5–SiO2玻璃陶瓷介电储能性能的影响

随着电力电子系统的不断发展,高功率脉冲电容器的需求增多。电介质电容器因具有放电功率大、充放电速度快及性能稳定等优点,在电力系统、电子器件、脉冲电源等方面发挥着重要作用,广泛应用于民用领域及军事领域。通过熔融压延制备玻璃基体,采用可控结晶工艺研究了不同含量的Bi₂O₃ (x=0.0%、1.0%、2.0%、4.0%,摩尔分数)对K₂O–B₂O₃–Sr O–Al₂O₃–Nb₂O₅–SiO₂玻璃陶瓷物相演化、微观结构、介电和储能性能的影响。在该玻璃陶瓷中,KSr₂Nb₅O₁₅为主要析出晶相,当Bi₂O₃的加入量为x=2.0%(摩尔分数)时,热处理温度为950℃时,玻璃陶瓷样品的储能密度最大可达到1.27 J/cm³,室温下介电常数可达342,是热处...     

不同介质中Ni-La2O3/SiO2-Al2O3催化剂稳定性研究

采用浸渍法制备Ni-La2O3/SiO2-Al2O3催化剂,选用四氢呋喃(THF)、γ-丁内酯(GBL)、1,4-丁二醇(BDO)、水(H2O)等常用溶剂作为介质对催化剂进行溶剂热处理,通过XRD、TG、H2-TPR手段对催化剂进行表征。结果表明,不同介质中催化剂活性组分发生不同程度的晶粒尺寸长大。经GBL处理过的催化剂Ni晶粒尺寸长大最明显,H2O处理次之,而THF的影响最小。     

Influence of Al2O3 whisker concentration on flexural strength of Al2O3(w)–ZrO2 (TZ-3Y) composite

On investigating the possibility of using alumina whisker reinforced 3 mol% Yttria stabilized Tetragonal Zirconia (TZ-3Y) composite for bioceramic applications, presented here is the influence of varying whisker concentration (2, 5, 10, 15 and 20 wt%) on flexural strength of the composite. Whiskers of hydrothermally synthesized Ammonium Aluminum Carbonate Hydroxide (AACH) were used for composite synthesis. These whiskers transformed in situ into alumina during sintering. It was found that with addition of alumina whiskers, strength was increased and reached a maximum value of 1212±60 MPa and 1325±65 MPa, in pure and 1 wt% CTAB added samples respectively, at a concentration of 10 wt% Al₂O₃ whiskers. The strength values of the synthesized composite can compete well with commercially available materials for dental applications.     

Low temperature sintering and microwave dielectric properties of Li2ZnTi3O8 ceramics doped with ZnO–La2O3–B2O3 glass

Li₂ZnTi₃O₈ ceramics doped with ZnO–La₂O₃–B₂O₃ glass were prepared by the conventional solid-state ceramic route. The effects of the ZnO–La₂O₃–B₂O₃ glass on the sintering temperature, phase composition, microstructure and microwave dielectric properties of Li₂ZnTi₃O₈ ceramics were investigated. The addition of ZLB glass can reduce the sintering temperature of Li₂ZnTi₃O₈ ceramic from 1075 °C to 925 °C without obvious degradation of the microwave dielectric properties. Only a single phase Li₂ZnTi₃O₈ with cubic spinel structure is formed in Li₂ZnTi₃O₈ ceramic with ZLB addition sintered at 925 °C. Typically, 1.0 wt% ZLB-doped Li₂ZnTi₃O₈ ceramic sintered at 925 °C can reach a maximum relative density of 95.8% and exhibits good microwave dielectric properties of ε_r=24.34, Q×f=41,360 GHz and τ_f=−13.4 ppm/°C. Moreover, this material is compatible with Ag electrode, which makes it a promising candidate for LTCC application.     

Synthesis of γ-Ga2O3-Al2O3 solid solutions by spray pyrolysis method

Synthesis of the γ-Ga₂O₃-Al₂O₃ solid solutions by spray pyrolysis was examined. Spherical particles were obtained using an aqueous solution of Al(NO₃)₃ and Ga(NO₃)₃ with HNO₃. For Ga-rich composition, γ-phase solid solutions were directly crystallized by the spray pyrolysis. For Al-rich composition, spray pyrolysis gave amorphous products unless a sufficient thermal energy was supplied during the spray pyrolysis. Subsequent calcination of the amorphous products gave γ-Ga₂O₃-Al₂O₃ solid solutions. However, physical properties of the solid solutions were affected by the spray pyrolysis conditions.     

H2O2处理H3PW12O40/ZrO2-WO3光催化降解有机染料

采用浸渍法将H3PW12O40负载在ZrO2-WO3上,通过H2O2溶液的敏化,制得H3PW12O40/ZrO2-WO3(x)光催化剂。然后以光降解甲基橙为探针反应,对各反应影响因素进行了探究。在甲基橙初始质量浓度为5 mg/L,溶液pH=2.5,催化剂用量为0.3 g的优化条件下,光降解2 h,甲基橙的降解率达到91.2%,光催化降解甲基橙溶液为一级动力学反应。且H3PW12O40/ZrO2-WO3(x)对罗丹明B、碱性品红和和亚甲基蓝也具有较高的光催化活性,降解率分别为70.0%、73.0%和73.5%。     

Emission analysis of CdO–Bi2O3–B2O3 glasses doped with Eu and Tb

This article reports on the emission properties of cadmium bismuth borate (CdBiB) glasses as a function of doping concentrations of Eu³⁺ and Tb³⁺ ions. The functional groups present in the glasses have been identified by analyzing FT-IR spectra. The emission spectra of Eu³⁺ and Tb³⁺:CdBiB glasses have shown reddish green emissions at 616 nm (⁵D₀→⁷F₂) under the excitation at 465 nm and at 547 nm (⁵D₄→⁷F₅) under the excitation at 485 nm, respectively. The Judd–Ofelt (J–O) theory was applied to evaluate the J–O intensity parameters from the absorption and the emission spectra; by using the J–O intensity (Ω_λ) parameters, spontaneous emission transition probability (A), total radiative transition rate (A_T), radiative lifetime (τ_R) and branching ratios (β) of the various emission transitions have been computed for both Eu³⁺ and Tb³⁺:CdBiB glasses. The quenching behavior in the emission intensity with increased concentration of Eu³⁺ and Tb³⁺ was observed, which could be useful for optimizing the compositions toward practical applications.     

Microwave dielectric characteristics of Nb2O5-added 0.9Al2O3–0.1TiO2 ceramics

The sintering characteristics, phase composition, and microwave dielectric properties of Nb₂O₅-added 0.9Al₂O₃–0.1TiO₂ ceramics sintered at 1300–1500 °C have been investigated. Results show that Nb⁵⁺ and Al³⁺ can co-substitute for Ti⁴⁺ and form Ti_0.8Al_0.1Nb_0.1O₂, which can lower effectively the sintering temperature, and improve the quality factor of 0.9Al₂O₃–0.1TiO₂ ceramics.     

CuO-Co3O4-CeO2/CeO2-Al2O3催化剂脱除CO性能研究

以CeO₂-Al₂O₃为载体,采用等体积浸渍法制备CuO-Co₃O₄-CeO₂/CeO₂-Al₂O₃催化剂,通过X射线衍射(XRD)、氢气程序升温还原(H₂-TPR)、氢气等温还原(H₂-TIR)、CO脱除性能评价等方法,考察预还原温度、反应温度、液相空速对CO脱除性能的影响。结果表明：催化剂在160℃下预还原可以获得37.3%的还原度,有效提高活性Cu⁺的数量,进而提高CO脱除性能;在液相丙烯中微量CO脱除反应中,反应温度升高、液相空速减小有利于提高CO脱除性能,当反应温度不低于50℃,液相空速不高于8 h^-1时,CO体积分数可脱除至0.03 mL/m³以下。在50℃、3 MPa,液相空速为8 h^-1的反应条件下,CuO-Co₃O