HCN Laser Interferometer on the EAST Superconducting Tokamak

A single-channel far-infrared （FIR） laser interferometer was developed to measure the line averaged electron density on the EAST tokamak. The structure of the single-channel FIR laser interferometer is described in detail. The evolution of density sawtooth oscillation was measured by means the FIR laser interferometer, and was identified by electron cyclotron emission （ECE） signals and soft X-ray intensity. The discharges with and without sawtooth were compared with each other in the Hugill diagram.     

Multipulse Nd：YAG Laser Thomson Scattering Diagnostics on HT-7 Tokamak

A multipulse Nd：YAG （Neodym-yttrium aluminium garnet） laser Thomson scattering diagnostic system developed was recently applied on HT-7 tokamak to obtain more accurate electron temperatures. A CAMAC-based real-time computer system for laser control, data acquisition, analysis and calibration was investigated in detail. Furthermore, the reliability and accuracy of this diagnostic system were demonstrated by comparing the results with those of a soft-X ray diagnostic system.     

Spectrum Blueshifting of Ultrashort UV Laser Pulse Induced by Ionization of Supersonic He and Ar Gas Jets

The predominant spectral blueshifting of a sub-picosecond UV laser pulse induced by ultrafast ionization of noble gases was investigated. Spectral measurements were made at various gas densities. Typical quasi-periodic structures in the blueshifted spectrum were obtained. The observations were in connection with the so-called self-phase modulation of laser pulses in the ultrafast ionization process which was simply simulated with an ADK （Ammosov-Delone-Krainov） ionization model. Some quantitative information can be deduced from the measurements and calculations.     

Experimental Investigation of Glass-Layer Confined Ablation in Laser Plasma Propulsion

Laser plasma propulsion in glass-layer confined ablation was experimentally investigated. The results showed that compared to that of direct ablation, the coupling coefficient was enhanced over ten times. By observing the plasma expansion and calculating the ablation pressure, it was found that a higher ablation pressure and larger glass mass resulted in a higher coupling coefficient in the confined laser ablation.     

Study of Bacterial Samples Using Laser Induced Breakdown Spectroscopy

Laser-induced breakdown spectroscopy （LIBS） technique has been applied to inves- tigate two different types of bacteria, Escherichia coli （B1） and Micrococcus luteus （B2） deposited on glass slides using Spectrolaser 7000. LIBS spectra were analyzed using spectrolaser software. LIBS spectrum of glass substrate was compared with bacteria spectra. Ca, Mg, Na, K, P, S, C1, Fe, A1, Mn, Cu, C, H and CN-band appeared in bacterial samples in air. Two carbon lines at 193.02 nm, 247.88 nm and one hydrogen line at 656.28 nm with intensity ratios of 1.9, 1.83 and 1.53 appeared in bacterial samples B1 and B2 respectively. Carbon and hydrogen are the important components of the bio-samples like bacteria and other cancer cells. Investigation on LIBS spectra of the samples in He and Ar atmospheres is also presented. Ni lines appeared only in B2 sample in Ar atmosphere. From the present experimental results we are able to show that LIBS technique has a potential in the identification and discrimination of different types of bacteria.     

Experimental Research on Plasma Induced by TEA CO2 Laser Propulsion

Results in the air-breathing propulsion experiments with a parabolic light craft and a self-made UV-preionized 100 J TEA CO2 laser device are presented. Air disturbance and the spectrum of the plasma after the interaction of pulsed laser radiation with the light craft were studied. It was found that the focal length of the parabolic light craft had a significant effect on the air-disturbance. Two shock waves were detected for the longer focal length, while only one shock wave detected for the short focal length. The spectrum of the laser-induced plasma, the distribution of the characteristic lines, and the temporal behaviors of the air plasma were studied in detail. The results showed that, the evolution of the laser-induced plasma lasted 20μs, and the plasma spectrum would reach the maximum intensity at 7μs.     

Characteristics of Ions Emitted from Laser-Induced Silver Plasma

In this work, study of laser-induced ions is presented. The plasma was produced by focusing a Nd：YAG laser, with a wavelength of 1064 nm, a pulsed width of 9-14 ns, a power of 1.1 MW and energy of 10 mJ, on silver target in vacuum （10-3 Torr= 1.3332 Pa）. The characteristics of ion streams were investigated by CR-39 detectors located at angles of 0°, 30°, 60° and 90° with respect to normal of the target. The distance between the silver target and each detector was 11 cm. The energy of silver ions was found ranging from 1.5 eV to 1.06E4 eV. There was a high concentration of ions with low energy as compared to those with high energy, showing the energy distribution amongst the ions. The flux of ions was maximum in the axial direction which was decreasing with the angle increase with respect to normal of the target, and finally became minimum in the radial direction. Hence the silver ions have shown anisotropic behaviour.     

Development of Data Acquisition Card Driver for ICRH System on EAST

Presented in this paper is the development of the driver for the data acquisition card with a peripheral component interconnection （PCI） local bus on the ion cyclotron range of frequency heating （1CRH） system. The driver is mainly aimed at the embedded VxWorks system （real-time operating system） which is widely used in various fields of real-time systems. An efficient way is employed to develop this driver, which will advance the real-time control of the ICRH system on the experimental advanced superconductor tokamak （EAST）. The driver is designed using the TORNADO integrated development environment （IDE）, and implemented in C plus language. The details include the hardware configuration, analogue/digital （A/D） and digital/analogue （D/A） conversion, input and output （I/O） operation of the driver to support over five cards. The data acquisition card can be manipulated in a low-level program and meet the requirements of A/D conversion and D/A outputs.     

Effect of Cold Plasma Treatment on Seed Germination and Growth of Wheat简

This study investigated the effect of cold helium plasma treatment on seed germina- tion, growth and yield of wheat. The effects of different power of cold plasma on the germination of treated wheat seeds were studied. We found that the treatment of 80 W could significantly improve seed germination potential （6.0%） and germination rate （6.7%） compared to the control group. Field experiments were carried out for wheat seeds treated with 80 W cold plasma. Com- pared with the control, plant height （20.3%）, root length （9.0%） and fresh weight （21.8%） were improved significantly at seedling stage. At booting stage, plant height, root length, fresh weight, stem diameter, leaf area and leaf thickness of the treated plant were respectively increased by 21.8%, 11.0%, 7.0%, 9.0%, 13.0% and 25.5%. At the same time, the chlorophyll content （9.8%）, nitrogen （10.0%） and moisture content （10.0%） were higher than those of the control, indicating that cold plasma treatment could promote the growth of wheat. The yield of treated wheat was 7.55 t-ha-1, 5.89% more than that of the control. Therefore, our results show that cold plasma has important application prospects for increasing wheat yield.     

Role of Ion Beam Irradiation and Annealing Effect on the Deposition of AlON Nanolayers by Using Plasma Focus Device

AlON nanolayers are synthesized on Al substrate by the irradiation of energetic nitrogen ions using plasma focusing. Samples are exposed to multiple （5, 10, 15, 20 and 25） focus shots. Ion energy and ion number density range from 80 keV to 1.4 MeV and 5.6×10^19 m^- 3 to 1.3×10^19 m ^-3, respectively. Moreover, the effect of continuous annealing （473 K and 523 K） on an AlN surface layer synthesized with 25 focus shots is also examined. The main features of the X-ray diffraction （XRD） patterns with increasing focus shots are： （i） variation in the crystallinity of AlN along （111）, （200） and （311） planes, （ii） increasing average crystallite size of AlN （111） plane, and （iii） stress relaxation observed in AlN （111） and （200） planes. The crystallinity of AlN surface layer is comparatively better at 473 K annealing temperature. A broadened diffraction peak related to an aluminium oxide phase showing weak crystallinity is observed for 15 focus shots while non-bounded oxides are present in all other deposited layers. Raman and Fourier transform infrared spectroscopy （FTIR） analysis confirm the presence of AlN and Al203 for the surface layer annealed at 473 K temperature. Raman analysis shows that the overlapping of AlN and Al2Oa results in the development of residual stresses. Scanning electron microscope （SEM） results demonstrate that the formation of rounded grains （range from 20 nm to 200 nm） and variations in their microstructures features depend on the increasing number of focus shots. Decomposition of larger clusters into smaller ones is observed.     

Simulation of Electron-Beam Generating Plasma at Atmospheric Pressure

As electron-beam generating plasma is widely applied, the software tool EGS4 （Electron-Gamma Shower） was used to simulate the transmission and energy deposition of electron-beam in air. The simulation results indicated that the range of the electron-beam was inversely proportional to the gas pressure in a wide range of gas pressure, and the electron-beam of 200 keV could generate a plasma with a density 10^11 cm^-3 in air of latm. In addition, the energy distribution of the beam-electron and plasma density profile produced by the beam were achieved.     

Study of Plume Characteristics of a Stationary Plasma Thruster

Electron density and temperature of the plume are measured by a double Langmuir probe in an experimental chamber. A numerical model based on both particle-in-cell scheme and direct simulation Monte Carlo hybrid method is developed to simulate the flow field of plume. The equation for plasma potential is solved by alternative direction implicit technique. The simulation is verified by comparing the computational results with the measured data. The study indicates that the electron temperature of flow field is about 2 eV and the electron density is about 2.5 ×10^16 - 5×10^15 m^-3 at the central line with a distance of 0.3 - 1.0 m downstream of the thruster exit. The model can well predict the flow field parameters of the steady plume. The efforts of this paper are referable for further investigation.     

Density and temperature of fermions and bosons from quantum fluctuations

A novel method to determine the density and temperature of a system constituted by fermions and/or bosons is proposed based on quantum fluctuations. For fermions system, the results in the limit where the reached temperature T is small and where there is no constraint for the reached temperature T compared to the Fermi energy ~f at a given density p are given, respectively. Quadrupole and multiplicity fluctuation relations are derived in terms of T/6f. We compared the two set results in the limit when Tis much smaller compared to Fermi energy Cf and they are consistent, as expected. The classical limit is also obtained for high temperatures and low densities. For bosons system, quadrupole and multiplicity fluctuations using Landau＇s theory of fluctuations near the critical point for a Bose-Einstein condensate （BEC） at a given density p are derived. As an example, we apply our approach to heavy ion collisions using the Constrained Molecular Dynamics model （CoMD） which includes the fermionic statistics. The multiplicity fluctuation quenching for fermions is found in the model and confirmed by experimental data. To reproduce the available experimental data better, we propose a modification of the collision term in the approach to include the possibility of ct-a collisions. The relevant Bose-Einstein factor in the collision term is properly taken into account. This approach increases the yields of bosons relative to fermions closer to data. Boson fluctuations become larger than one as expected.     

Thermal Analysis and Optimization for Cryopanel of NBI Cryocondensation Pump

Excellent vacuum performance ensures a high beam transmission efficiency of the neutral beam injector （NBI）. The vacuum performance is mainly determined by the cryoperformance of the cryopanel of the cryocondensation pumps which are the main vacuum pumps of NBI. In order to optimize the cryoperformance, the requirements for the temperature distribution and the heat load of the cryopanel are analysed and the factors that affect the cryopanel＇s temperature distribution are studied. The results indicate that the temperature difference of the cryopanel can be reduced by fabricating the cryopanel with high thermal conductivity material, increasing its thickness and cutting the distance between the two upward cooling pipes. The results may be applied to a cryopanel cooled by forced flow liquid helium.     

Simultaneous Oxidization of NOx and SO2 by a New Non-thermal Plasma Reactor Enhanced by Catalyst and Additive

The non-thermal plasma as one of the most promising technologies for removing NOx and SO2 has attrm~ted much attention. In this study, a new plasma reactor combined with catalyst and additive was developed to effectively oxidize and remove NOx and SO2 in the flue gas. The experimental results showed that TiO2 could improve the oxidation efficiency of SO2 in the case of applying plasma while having a negative effect on the oxidation process of NO and NOx. With the addition of NH3, the oxidation rates of NOx, NO and SO2 were slightly increased. However, the effect of adding NH3 on NOx oxidation was negative when the temperature was above 200℃.     

Study of Atmospheric Pressure Abnormal Glow Discharge

Atmospheric pressure abnormal glow discharge （APAGD） was carried out simply with a transformer of 1 ： 500 driven by a alternating current with a frequency of 50 Hz. Typical stable discharge parameters, namely voltage of 400 V to 850 V and current of 60 mA to 110 mA were measured by oscillograph. Simulation of the discharge process suggested that the stable discharge was supported by the impedance from the secondary coil of the transformer, which offered a negative feedback to prevent the discharge from turning into an arc. An interpretation was given for the oscillogram of the sinuous discharge current and square voltage. Furthermore, the electron temperature and electron density averaged in the discharge channel of APAGD were estimated.     

Application of Super-Synchronization Speed Control Technology in Two 80 MVA Motor-Generator Units of HL-2A

Two sets of super-synchronization speed control assemblies for two 80 MVA motor-generator units have been developed successfully in order to satisfy the demand of the toroidal field system in the HL-2A tokamak. Based on the three-phase logical no-circumfluence a.c./a.c. cycloconverter, the speeds of two 2500 kW double fed drive motors have been regulated by means of the vector control technology. The maximum operating speed of each motor- generator unit has been raised from 1488 rpm （revolutions per minute） to 1650 rpm and the released energy of each unit during a pulsed discharge can reach 500 MJ. As a result, the toroidal field system has the capacity to provide 2.8 tesla （T） in HL-2A experiments.     

Mechanical Properties of Thermoplastic Polyurethanes Laminated Glass Treated by Acid Etching Combined with Cold Plasma

To overcome the problem of interlaminar delamination of thermoplastic polyurethane laminated glass, silicate glass was etched with hydrofluoric acid and thermoplastic polyurethane was then treated with cold plasma. Compared with the untreated samples, the interlaminar shear strength of acid etching samples, cold plasma-treated samples and acid etching combined with cold plasma-treated samples increased by 97%, 84% and 341%, respectively. Acid etching combined with cold plasma-treated samples exhibited a higher flexural strength and strain as compared with the untreated samples. The impact energy of acid etching samples, cold plasmatreated samples and acid etching combined with cold plasma-treated samples increased by 8.7%, 8.1% and 11.6%, respectively, in comparison with the untreated samples. FT-IR analysis showed that a large number of -C-O, CO N and CO O C groups appeared on the surface of cold plasma-treated thermoplastic polyurethane, which resulted in the formation of hydrogen bonds. SEM results showed that some pittings formed on the surface of the silicate glass treated by acid etching, which resulted in the formation of a three-dimensional interface structure between tile silicate glass and polyurethane. Hydrogen bonds combined with the three-dimensional interface between silicate glass and polyurethanes co-improved the mechanical properties of thermoplastic polyurethanes laminated glass.     

Second Discharge Characteristics of Aluminum Wire Electrical Explosion Under Various Argon Pressures

Electrical wire explosion is a promising method for the preparation of metal nanopowder, but the properties of metal nanopowder are affected by the second discharge process of electrical wire explosion. The second discharge characteristics of aluminum wire electrical ex- plosion under variant argon pressures were studied in a RLC discharge circuit. The results show that the curve of the second discharge voltages versus the pressure presents a U-shape. To clarify the roles of aluminum vapor and argon in the process of the second discharge, a spectrograph and a high speed framing camera were used to study the radiation spectrum and spatial distribution of the electrical explosion plasma. It is observed that argon participates in the second discharge process under low pressure. A discharge channel develops along the surface of the aluminum vapor. Under higher pressure, a second discharge takes place in the aluminum vapor and the discharge channel is inside the aluminum vapor.     

Experimental Study on Indoor Air Cleaning Technique of Nano-Titania Catalysis Under Plasma Discharge

In this study, a new technique of air cleaning by plasma combined with catalyst was proposed, which consisted of electrostatic precipitation, volatile organic compounds （VOCs） decomposition and sterilization. A novel indoor air purifier based on this technique was adopted. The experimental results showed that formaldehyde decomposition by the plasma-catalyst hybrid system was more efficient than that by plasma only, Positive discharge was better than negative discharge in formaldehyde removal. Meanwhile, the outlet concentration of ozone byproduct was effectively reduced by the nano-titania catalyst.