Pervaporation characteristics and structure of poly(vinyl alcohol)/poly(ethylene glycol)/tetraethoxysilane hybrid membranes

Poly(vinyl alcohol) (PVA) blended with poly(ethylene glycol) (PEG) was crosslinked with tetraethoxysilane (TEOS) to prepare organic–inorganic PVA/PEG/TEOS hybrid membranes. The membranes were then used for the dehydration of ethanol by pervaporation (PV). The physicochemical structure of the hybrid membranes was studied with Fourier transform infrared spectra (FT‐IR), wide‐angle X‐ray diffraction WXRD, and scanning electron microscopy (SEM). PVA and PEG were crosslinked with TEOS, and the crosslinking density increased with increases in the TEOS content, annealing temperature, and time. The water permselectivity of the hybrid membranes increased with increasing annealing temperature or time; however, the permeation fluxes decreased at the same time. SEM pictures showed that phase separation took place in the hybrid membranes when the TEOS content was greater than 15 wt %. The water permselectivity increased with the addition of TEOS and reached the maximum at 10 wt % TEOS. The water permselectivity decreased, whereas the permeation flux increased, with an increase in the feed water content or feed temperature. The hybrid membrane that was annealed at 130°C for 12 h exhibited high permselectivity with a separation factor of 300 and a permeation flux of 0.046 kg m^?2 h^?1 in PV of 15 wt % water in ethanol. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Poly(ether sulfone) supported hybrid poly(vinyl alcohol)–maleic acid–silicone dioxide membranes for the pervaporation separation of ethanol–water mixtures

Microporous poly(ether sulfone) (PES) supported hybrid polymer–inorganic membranes were prepared by the crosslinking of poly(vinyl alcohol) (PVA), maleic acid (MA), and SiO₂ via an aqueous sol–gel route and a solution‐casting method. The membrane performance was tested for the pervaporation separation of ethanol–water mixtures from 20 to 60 °C with a feed ethanol concentration of 96 wt %. The membrane characterization results reveal that different SiO₂ loadings affected the crystallinity and roughness of the membranes. The PVA–MA–SiO₂ membrane containing 10 wt % SiO₂ showed that SiO₂ nanoparticles were well dispersed within the polymer matrix; this resulted in significant enhancements in both the flux and selectivity. The membrane achieved a high water permeability of 1202 g·μm·m^?2 h^?1 kPa^?1 and a selectivity of 1027 for the separation of a 96 wt % ethanol‐containing aqueous solution. This enhanced membrane performance might have been due to the dense crosslinking membrane network, increased free volume, and uniform distribution of SiO₂ nanoparticles. Both the water and ethanol fluxes increased with the feed water concentration and temperature. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134 , 44839.     

Preparation of PFSA‐PVA/PSf hollow fiber membrane for IPA/H2O pervaporation process

Using Na⁺ form of perfluorosulfonic acid (PFSA) and poly(vinyl alcohol) (PVA) as coating materials, polysulfone (PSf) hollow fiber ultrafiltration membrane as a substrate membrane, PFSA‐PVA/PSf hollow fiber composite membrane was fabricated by dip‐coating method. The membranes were post‐treated by two methods of heat treatment and by both heat treatment and chemical crosslinking. Maleic anhydride (MAC) aqueous solution was used as chemical crosslinking agent using 0.5 wt % H₂SO₄ as a catalyst. PFSA‐PVA/PSf hollow fiber composite membranes were used for the pervaporation (PV) separation of isopropanol (IPA)/H₂O mixture. Based on the experimental results, PFSA‐PVA/PSf hollow fiber composite membrane is suitable for the PV dehydration of IPA/H₂O solution. With the increment of heat treatment temperature, the separation factor increased and the total permeation flux decreased. The addition of PVA in PFSA‐PVA coating solution was favorable for the improvement of the separation factor of the composite membranes post‐treated by heat treatment. Compared with the membranes by heat treatment, the separation factors of the composite membranes post‐treated by both heat treatment and chemical crosslinking were evidently improved and reached to be about 520 for 95/5 IPA/water. The membranes post‐treated by heat had some cracks which disappeared after chemical crosslinking for a proper time. Effects of feed temperature on PV performance had some differences for the membranes with different composition of coating layer. The composite membranes with the higher mass fraction of PVA in PFSA‐PVA coating solution were more sensitive to temperature. It was concluded that the proper preparation conditions for the composite membranes were as follows: firstly, heated at 160°C for 1 h, then chemical crosslinking at 40°C for 3 h in 4% MAC aqueous solution. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Pervaporation separation of water/isopropanol mixtures through crosslinked carboxymethyl chitosan/polysulfone hollow‐fiber composite membranes

Carboxymethyl chitosan (CMCS)/polysulfone (PS) hollow‐fiber composite membranes were prepared through glutaraldehyde (GA) as the crosslinking agent and PS hollow‐fiber ultrafiltration membrane as the support. The permeation and separation characteristics for dehydration of isopropanol were investigated by the pervaporation method. Pure chitosan, carboxymethyl chitosan, and crosslinked carboxymethyl chitosan membranes were characterized by Fourier transform infrared (FT‐IR) spectroscopy and X‐ray diffraction (XRD) to study the crosslinking reaction mechanism and degree of crystallinity, respectively. The effects of feed composition, crosslinking agent, membrane thickness, and feed temperature on membrane performance were investigated. The results show that the crosslinked CMCS/PS hollow‐fiber composite membranes possess high selectivity and promising permeability. The permeation flux and separation factor for isopropanol/water is 38.6 g/m²h and 3238.5, using 87.5 wt % isopropanol concentration at 45°C, respectively. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 1959–1965, 2007     

Poly(acrylic acid)–poly(vinyl alcohol) semi- and interpenetrating polymer network pervaporation membranes

A series of poly(acrylic acid) (PAA)–poly(vinyl alcoho) (PVA) semiinterpenetrating (SIPN) and interpenetrating (IPN) polymer network membranes were prepared by crosslinking PVA alone or by crosslinking both PVA and PAA. Glutaraldeyde and ethylene glycol were used as crosslinking agents for the PVA and PAA networks, respectively. The presence of PAA increases the permeability of the membranes while the presence of PVA improves their mechanical and film-forming properties. The mechanical properties of the membranes were investigated via tensile testing. These hydrophilic membranes are permselective to water from ethanol–water mixture and to ethanol from ethanol–benzene mixtures. The IPN membranes were employed for the former mixtures and the SPIN membranes for the latter, because the IPN ones provided too low permeation rates. The permeation rates and seperation factors were determined as functions of the IPN or SIPN composition, feed composition, and temperature. For the azeotropic ethanol–water mixture (95 wt % ethanol), the separation factor and permeation rate at 50°C of the PAA-PVA IPN membrane, containing 50 wt % PAA, were 50 and 260 g/m²h, respectively. For the ethanol–benzene mixture, the PAA–PVA SIPN membranes had separation factors between 1.4 and 1200 and permeation rates between 6 and 550 g/m²h, respectively, depending on the feed composition and temperature. © 1996 John Wiley & Sons, Inc.     

Modified polydimethylsiloxane/polystyrene blended IPN pervaporation membrane for ethanol/water separation

In this article a modified polydimethylsiloxane (PDMS) blended polystyrene (PS) interpenetrating polymer network (IPN) membranes supported by Teflon (polytetrafluoroethylene) ultrafiltration membrane were prepared for the separation of ethanol in water by pervaporation application. The relationship between the surface characteristics of the surface‐modified PDMS membranes and their permselectivity for aqueous ethanol solutions by pervaporation are discussed. The IPN supported membranes were prepared by sequential IPN technique. The IPN supported membrane were tested for the separation performance on 10 wt % ethanol in water and were characterized by evaluating their mechanical properties, swelling behavior, density, and degree of crosslinking. The results indicated that separation performance, mechanical properties, density, and the percentage of swelling of IPN membranes were influenced by degree of crosslink density. Depending on the feed temperature, the supported membranes had separation factors between 2.03 and 6.00 and permeation rates between 81.66 and 144.03 g m^?2 h^?1. For the azeotropic water–ethanol mixture (10 wt % ethanol), the supported membrane had at 30°C a separation factor of 6.00 and a permeation rate of 85 g m^?2 h^?1. Compared to the PDMS supported membranes, the PDMS/PS IPN supported blend membrane ones had a higher selectivity but a somewhat lower permeability. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Comparative behavior of PVA/PAN and PVA/PES composite pervaporation membranes in the pervaporative dehydration of caprolactam

Flat‐sheet composite membranes were developed by the traditional phase inversion technique using poly;(vinyl alcohol) (PVA). PVA composite pervaporation (PV) membranes were prepared with crosslinked PVA selective layer and porous polyacrylonitrile (PAN) and polyether sulfone (PES) substrate layer material as supports for separating heat sensitivity substance ε‐caprolactam (CPL) from CPL/water mixtures. Glutaraldehyde was used as crosslinking agent. The effect of the composition of glutaraldehyde on membrane stability and structure were investigated. The operating parameters, such as feed concentration and operating temperature, remarkably affected PV performance of the composite membranes. The composite membranes with PVA casted on PAN (PVA/PAN) showed superior PV performance than that casted on PES (PVA/PES). This study has also shown that the type of porous support plays an important role in the PV performance. As a result, this work has presented the information needed of the behavior of PV membranes for dehydration applications of industrial caprolactam. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 4005–4011, 2007     

Preparation of water‐swollen hydrogel membranes for gas separation

Water‐swollen hydrogel (WSH) membranes for gas separation were prepared by the dip‐coating of asymmetric porous polyetherimide (PEI) membrane supports with poly(vinyl alcohol) (PVA)–glutaraldehyde (GA), followed by the crosslinking of the active layer by a solution method. Crosslinked PVA/GA film of different blend compositions (PVA/GA = 1/0.04, 0.06, 0.08, 0.10, 0.12 mol %) were characterized by differential scanning calorimetry (DSC) and their water‐swelling ratio. The swelling behavior of PVA/GA films of different blend compositions was dependent on the crosslinking density and chemical functional groups created by the reaction between PVA and GA, such as the acetal group, ether linkage, and unreacted pendent aldehydes in PVA. The permeation performances of the membranes swollen by the water vapor contained in a feed gas were investigated. The behavior of gas permeation through a WSH membrane was parallel to the swelling behavior of the PVA/GA film in water. The permeation rate of carbon dioxide through the WSH membranes was 10⁵ (cm³ cm^?2 s^?1 cmHg) and a CO₂/N₂ separation factor was about 80 at room temperature. The effect of the additive (potassium bicarbonate, KHCO₃) and catalyst (sodium arsenite, NaASO₂) on the permeation of gases through these WSH membranes was also studied. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 1785–1791, 2001     

Modified poly(vinyl alcohol)/chitosan blended membranes for isopropanol dehydration via pervaporation: Synthesis optimization and modeling by response surface methodology

Box–Behnken (BB) design of response surface methodology (RSM) was effectively applied to optimize fabrication conditions of modified poly(vinyl alcohol) (PVA) and chitosan (CS) blended pervaporation (PV) membranes. The PVA/CS membranes were crosslinked either by chemical reaction with glutaraldehyde (GA) or by heat‐treating at different temperatures. The main objectives were to determine the optimal levels of fabricating parameters and also to investigate interactions among the variables. CS content in the blended membranes, concentration of crosslinking agent and heat‐treating temperature were the fabrication parameters, the main effects and interaction effects of which on membrane structure and PV performance toward isopropanol (IPA)/water dehydration were investigated, and for which regression models were established. The modified PVA/CS blended membranes were characterized by means of scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR) as well as X‐ray diffraction (XRD). It was found that the CS content is the most significant factor influencing flux and separation factor among the three studied variables and the experimental results are in excellent accordance with predicted values from the developed RSM regression models. The RSM results indicated that under preparation conditions of 80 wt % CS in the blended membrane, 0.58 wt % GA concentration, and 77 °C heat‐treating temperature, the maximum separation factor of 5222.8 and the normalized flux of 9.407 kg µm/m²h can be acquired with feed content of 85 wt % IPA at 25 °C, showing that the prepared membrane is highly efficient for PV dehydration of IPA. The models were satisfactorily validated against experimental data. Furthermore, the optimum membrane presents excellent separation performance at different feed compositions and temperatures. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44587.     

A polyvinyl alcohol-based mixed matrix membrane with uniformly distributed Schiff base network-1 for ethanol dehydration

In this study, Schiff base network (SNW)-1 nanoparticles with high hydrophilicity and large specific surface area were used to prepare polyvinyl alcohol (PVA)-based mixed matrix membranes (MMMs), which were evaluated for ethanol dehydration. Because of the low difference of density between SNW-1 and PVA, the as-prepared nanoparticles can be uniformly distributed into the PVA active layer. The effects of SNW-1 loading, feed temperature, and water concentration on pervaporation (PV) performance were further studied. The results showed the MMM with 10 wt% of SNW-1 loading exhibited a separation factor of 1,501 and a permeation flux of 187 g m⁻² h⁻¹ for feeding 95 wt% ethanol/water binary solution at 75°C. Overall, the SNW-1/PVA MMMs showed great prospect in ethanol dehydration via PV.     

Pervaporation properties of polyvinyl alcohol/ceramic composite membrane for separation of ethyl acetate/ethanol/water ternary mixtures

In further purification of ethyl acetate (EAC) process, azeotropic distillation or extractive distillation is usually applied. High energy consumption limits the economic profit of the process. In this study, pervaporation separation of EAC/ethanol (EA)/water ternary mixtures using the ceramic-supported polyvinyl alcohol (PVA) composite membrane was investigated to substitute the azeotropic distillation or extractive distillation. Swelling experiments were performed to evaluate the sorption characteristic of the membrane. Flory-Huggins theory was applied to study the interaction between the membrane and the penetrant. The UNIFAC model was adopted to investigate the variation of the penetrant activity in the membrane. The effects of operation temperature, feed water content and feed flow rate on the PV performance of the membrane were systematically investigated. The composite membrane exhibited high PV performance with the total flux of 2.1 kg·m⁻²·h⁻¹ and 94.9 wt% permeate concentration of water (operation condition: feed composition 82.6 wt% EAC, 8.4 wt% EA, 9 wt% water, feed temperature 60 °C, feed flow rate 252 mL· min⁻¹). The PV performance of the membrane varied slightly over a continuous PV experiment period of 110 h. Our results demonstrated that the PVA/ceramic membrane was a potential candidate for the purification of EAC/EA/water ternary mixtures.     

Chitosan/Gelatin Blend Membranes for Pervaporation Dehydration of 1,4-Dioxane

Abstract

This paper deals with the development of compatible blend membranes of chitosan (CS) and gelatin (GL) by solution casting and crosslinking with glutaraldehyde. The membranes were tested in pervaporation (PV) dehydration of 1,4-dioxane. Membrane characterizations by Fourier transform infrared spectroscopy, wide-angle X-ray diffraction, and a universal testing machine were done to understand their physicochemical properties and for their suitability under PV conditions. The blend membranes were more water selective compared to pristine chitosan membrane at 30°C. Flux increased with increasing wt.% of water of the feed and also by increasing the gelatin content of the blend, but selectivity decreased. Sorption experiments gave information on the interaction between feed mixture and membrane polymers. Membranes of this study could extract nearly 97 wt.% of water from the feed mixture. Arrhenius activation parameters and diffusion coefficients estimated from a temperature dependence of PV results could explain the PV results satisfactorily.     

Characterization of sodium alginate and poly(vinyl alcohol) blend membranes in pervaporation separation

By blending a rigid polymer, sodium alginate (SA), and a flexible polymer, poly(vinyl alcohol) (PVA), SA/PVA blend membranes were prepared for the pervaporation separation of ethanol–water mixtures. The rigid SA membrane showed a serious decline in flux and a increase in separation factor due to the relaxation of polymeric chains, whereas the flexible PVA membrane kept consistent membrane performance during pervaporation. Compared with the nascent SA membrane, all of the blend membranes prepared could have an enhanced membrane mobility by which the relaxation during pervaporation operation could be reduced. From the pervaporation separation of the ethanol–water mixtures along with the temperature range of 50–80°C, the effects of operating temperature and PVA content in membrane were investigated on membrane performance, as well as the extent of the relaxation. The morphology of the blend membrane was observed with PVA content by a scanning electron microscopy. The relaxational phenomena during pervaporation were also elucidated through an analysis on experimental data of membrane performance measured by repeating the operation in the given temperature range. SA/PVA blend membrane with 10 wt % of PVA content was crosslinked with glutaraldehyde to enhance membrane stability in water, and the result of pervaporation separation of an ethanol–water mixture through the membrane was discussed. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 67:949–959, 1998     

Properties and pervaporation performance of poly(vinyl alcohol) membranes crosslinked with various dianhydrides

In this work, three dianhydrides with similar chemical structures, 3,3′,4,4′‐benzophenone tetracarboxylic dianhydride (BTDA), 4,4′‐oxydiphthalic anhydride (ODPA), and pyromellitic dianhydride (PMDA), are employed for the crosslinking modification of poly(vinyl alcohol) (PVA) membranes for ethanol dehydration via pervaporation. The changes in crosslinking degree, surface hydrophilicity, and glass‐transition temperature are investigated and compared. Compared to the pure PVA membrane, all crosslinked membranes show higher fluxes but lower separation factors, because of the higher fractional free volume and the lower hydrophilicity by the crosslinking of the PVA matrix, respectively. In addition, all crosslinked PVA membranes exhibit similar flux, and the separation factor presents a decreasing order of PVA/PMDA‐2 > PVA/ODPA‐2 > PVA/BTDA‐2, which is in the reverse order of their hydrophilicity, probably because of the reduction in the swelling resistance. With the PMDA content increasing from 0.01 to 0.04 mol/(kg PVA) in the PVA/PMDA crosslinked membranes, the crosslinking degree is enhanced and the hydrogen bonding is weakened, resulting in a flux increase from 120.2 to 190.8 g m^?2 h^?1, but the separation factor declines from 306 to 58. This work is believed to provide useful insight on the chemical modification of PVA membranes for pervaporation and other membrane‐based separation applications. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46159.     

Gasoline desulfurization by a TiO2‐filled ethyl cellulose pervaporation membrane

The TiO₂ nanoparticles were incorporated into an ethyl cellulose (EC) matrix to improve the pervaporation (PV) performance of the membrane for gasoline desulfurization. The microstructures of different EC membranes were characterized by scanning electron microscopy, Fourier transform infrared spectroscopy, and X‐ray and transmission electron microscopy. The PV experiments showed that the hybrid membrane of EC/TiO₂ demonstrated an improved permeation flux (J ) of 7.58 kg m^?2 h^?1 and a sulfur enrichment factor (α) of 3.13 in comparison with the pure EC membrane, with a J of 3.73 kg m^?2 h^?1 and an α of 3.69. In addition, the effects of the operating conditions, including the operating temperature, layer thickness, crosslinking time, feed flow rate, and feed sulfur content level, on the PV performance of the EC/TiO₂ membrane were investigated. Under a 100 mL/min feed flow rate and a 85 μg/g sulfur content, J of the 10 μm thick membrane increased to 7.58 kg m^?2 h^?1 with α of 3.13 compared to the pure EC membrane (3.73 kg m^?2 h^?1, 3.69) at 80 °C with 30 min of crosslinking time. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 : 134 , 43409.     

Pervaporation dehydration of ethyl acetate aqueous solution using the doubly modified polyvinyl alcohol (PVA) composite membrane

Polyvinyl alcohol–tetraethoxysilane–perfluorosulfonic acid (PVA–TEOS–PFSA) hybrid membrane was prepared by sol–gel method through PVA being modified doubly by PFSA and TEOS. With polyacrylonitrile (PAN) ultrafiltration membrane as a substrate membrane, PVA–TEOS–PFSA/PAN composite membrane was fabricated by dip-coating method for pervaporation (PV) dehydration of ethyl acetate (EAc) aqueous solution. The hybrid membrane was characterized by swelling degree, static contact angle, Fourier transform infrared spectra and scanning electron microscope. Effects of PFSA and TEOS contents in coating solution on PV performance of composite membrane were investigated, respectively. With increasing PFSA content, the permeation flux of composite membrane increased, while the separation factor decreased. Just the opposite, the increase of TEOS content resulted in the decrease in permeation flux and the increase in separation factor. In addition, the PV performances of composite membranes were also investigated at different feed temperatures and water concentrations in feed, respectively. The PVA–TEOS–PFSA/PAN composite membrane, which was prepared from coating with PVA/PFSA mass ratio of 80/20 and TEOS content of 20 wt%, exhibited the permeation flux of 347.9 g m^?2 h^?1 and the separation factor of 2218 for PV dehydration of 2 wt% water of EAc solution at 40 °C.     

Incorporation of multiwalled carbon nanotubes into poly(vinyl alcohol) membranes for use in the pervaporation of water/ethanol mixtures

Multiwalled carbon nanotube (MWNT)/poly (vinyl alcohol) (PVA) blend membranes were prepared by the solution‐casting method to determine the effect of MWNTs with nanoscale empty inner space along the tube length on the pervaporation performance of a PVA membrane in the separation of alcohol/water mixtures. The blend membranes were then characterized with several analytical methods such as transmission electron microscopy, differential scanning calorimetry, and X‐ray diffractometry: Transmission electron microscopy showed that the MWNTs were homogeneously distributed through the PVA matrix. The glass‐transition temperature of the PVA membrane was increased from 69.21 to 78.53°C via blending with MWNTs. The crystallinity of the PVA matrix decreased with increasing MWNTs up to 5 wt % from 41 to 36%. The pervaporation properties of the blend membranes were completely different from those of the pure PVA membrane in the separation of water/ethanol mixtures. The flux of the membrane was increased with the amount of MWNTs, whereas the separation factor was maintained up to 1.0 wt % MWNTs. However, beyond that, it was reduced. These results suggested that two factors, the crystallinity of the membrane and the diameters of the MWNTs, affected the performance of the membranes. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Pervaporation separation of aqueous organic mixtures through sulfated zirconia‐poly(vinyl alcohol) membrane

Sulfated zirconia‐poly(vinyl alcohol) membranes were prepared, and pervaporation performances for aqueous organic mixtures were investigated. These hydrophilic membranes were formed by crosslinking poly(vinyl alcohol) (PVA) with the solid acid of sulfated zirconia by an acid‐catalyzed reaction. The pervaporation performances were measured as a function of the content ratio of sulfated zirconia to PVA, which affected the degree of swelling for water and the crosslinking density of the membrane. The membrane selectivity in pervaporation of aqueous organic mixtures increased in order of acetic acid < ethanol < 2‐ethoxyethanol without sacrificing the permeation rate, depending on their feed compositions. The effects of feed temperature and concentration on the membrane performance were also significant. It was found that sulfated zirconia in the membrane preparation played an important role as a filler material as well as an effective crosslinking or insolubilization agent in improving and controlling the membrane performance, i.e., permeation rate and selectivity. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 79: 1450–1455, 2001     

Crosslinked blended poly(vinyl alcohol)/N-methylol nylon-6 membranes for the pervaporation separation of ethanol–water mixtures

Crosslinked blended membranes of poly(vinyl alcohol) (PVA) and N-methylol nylon-6 were prepared either by thermal crosslinking at 180°C or by chemical crosslinking with maleic acid. The pervaporation performance for the separation of ethanol–water mixtures of these membranes was investigated in terms of feed concentration, PVA content, and crosslinking agent content. The pervaporation performance of two differently crosslinked membranes was strongly influenced by the nature of the crosslinkage. Significant improvement in the pervaporation separation index can be achieved for chemically crosslinked membranes. From the comparison between the pervaporation and sorption tests, it is suggested that, for hydrophilic membranes, sorption properties dominate the pervaporation performance at feed solutions of higher water content, while diffusion properties govern at feed solutions of higher ethanol content. © 1998 John Wiley & Sons, Inc. J. Appl. Polym. Sci. 70: 317–327, 1998     

Synthesis of ion‐imprinting chitosan/PVA crosslinked membrane for selective removal of Ag(I)

A novel ion‐imprinted membranes were synthesized for selective removal and preconentration for Ag(I) ions from aqueous solutions. The membranes were obtained via crosslinking of chitosan (CS), PVA, and blend chitosan/PVA using glutaraldehyde (GA) as crosslinker. The FTIR spectra were used to confirm the membrane formation. Comparing with the nonimprinted membranes, Ag(I)‐imprinted CS and CS/PVA has higher removal capacity and selectivity for Ag⁺ ions. An enhancement in the Ag⁺ removal capacity by ～ 20% (from 77.8 to 94.4 mg g^–1) and ～ 50% (from 83.9 to 125 mg g^–1) was found in the Ag(I)‐imprinted CS and Ag(I)‐imprinted CS/PVA membranes, respectively, when compared with the nonimprinted membranes. Removal equilibra was achieved in about 40 min for the non‐ and ion‐imprinted CS/PVA. The pH and temperature significantly affected the removal capacity of ion‐imprinted membrane. The relative selectivity coefficient values of Ag⁺/Cu²⁺ and Ag⁺/Ni²⁺ are 9 and 10.7 for ion‐imprinted CS membrane and 11.1 and 15 for ion‐imprinted CS/PVA membrane when compared with nonimprinted membranes. The imprinted membranes can be easily regenerated by 0.01M EDTA and therefore can be reused at least five times with only 15% loss of removal capacity. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009