Fire structural resistance of basalt fibre composite

Basalt fibres are emerging as a replacement to E-glass fibres in polymer matrix composites for selected applications. In this study, the fire structural resistance of a basalt fibre composite is determined experimentally and analytically, and it is compared against an equivalent laminate reinforced with E-glass fibres. When exposed to the same radiant heat flux, the basalt fibre composite heated up more rapidly and reached higher temperatures than the glass fibre laminate due to its higher thermal emissivity. The tensile structural survivability of the basalt fibre composite was inferior to the glass fibre laminate when exposed to the same radiant heat flux. Tensile softening of both materials occurred by thermal softening and decomposition of the polymer matrix and weakening of the fibre reinforcement, which occur at similar rates. The inferior fire resistance of the basalt fibre composite is due mainly to higher emissivity, which causes it to become hotter in fire.     

The effect of polypropylene,polyvinyl-alcohol,carbon and glass fibres on geopolymers properties

Recently, the inclusion of different types of fibres into geopolymers, as reinforcement, has amplified due to the rapid increase in geopolymers developments. In spite of geopolymers have prospective properties such as low carbon footprint, low consumption of energy, good compressive strength, resistance to fire, resistance to flame, resistance to corrosion and good durability, they undergo from low tensile strength and flexural strength. To avoid these shortages, different types of fibres could be incorporated into geopolymers to enhance their toughness, tensile strength and ductility. The current survey aims to review the effect of different types of fibres named polypropylene (PP), polyvinyl alcohol (PVA), carbon and glass fibres on the fresh and hardened properties of geopolymers.     

Tailoring of dual-interface in high tenacity PP composites – Toughening with positive hybrid effect

The study proves the feasibility of manufacturing injection moulded polypropylene composites reinforced with short rayon cellulose fibres of two selectively tailored fibre–matrix interfaces. The originally developed method relies on selective chemical grafting of two different polymer waxes onto the surface of cellulose fibres in order to obtain two different strengths of fibre–matrix interfaces in one composite. This selective tailoring of a dual-interface is meant to improve the notched impact strength without deteriorating of its flexural strength. Compatibilised fibres have a strong interphase, which conditions the transfer of strain from the matrix to fibres during deformation. Fibres tailored for a weak interface more efficiently hinder the crack propagation at crash. A 32% improvement of composite notched impact strength was achieved with merely a 5% deterioration of its flexural strength. Its specific properties are on the level or better than those of polypropylene counterpart reinforced with the same content of glass fibres.     

The effect of fibre content on the mechanical properties of hemp and basalt fibre reinforced phenol formaldehyde composites

In this study, mechanical properties such as tensile, flexural and impact strengths of hemp/phenol formaldehyde (PF), basalt/PF and hemp/basalt hybrid PF composites have been investigated as a function of fibre loading. Hemp fibre reinforced PF composites and basalt fibre reinforced composites were fabricated with varying fibre loading i.e. 20, 32, 40, 48, 56 and 63 vol%. The hybrid effect of hemp fibre and basalt fibre on the tensile, flexural and impact strengths was also investigated for various ratio of hemp/basalt fibre loading such as 1:0, 0.95:0.05, 0.82:0.18, 0.68:0.32, 0.52:0.48, 0.35:0.65, 0.18:0.82 and 0:1. Total fibre loading of the hybrid composites was 40 vol%. The results showed that the tensile strength and elongation at break increase with increasing fibre loading up to 40 vol% and decrease above this value for hemp fibre reinforced PF composite. Similar trend was observed for flexural strength and the maximum value was obtained for 48 vol% hemp fibre loading. Impact strength of hemp/PF composite showed a regular trend of increase with increasing fibre loading up to 63 vol%. Tensile strength, flexural strength and impact strength values of basalt/PF composites were found to be lower compared to hemp/PF composites. The tensile strength and elongation at break of basalt/PF composite increased by incorparation of basalt fibre up to 32 vol% and decreased beyond this value. Flexural strength of basalt/PF composite decreased linearly with fibre loading. However, the maximum impact strength was obtained for 48 vol% basalt fibre loading. For hemp/basalt hybrid PF composite, the tensile strength decreased with increasing basalt fibre loading. On the other hand, the flexural and impact strengths showed large scatter. The maximum flexural strength value was obtained for 0.52:0.48 hemp/basalt ratio. Corresponding value for impact strength was obtained for 0.68:0.32 hemp/basalt fibre ratio.     

Plasma surface modification of advanced organic fibres

The interlaminar shear strength, interlaminar fracture energy, flexural strength and modulus of extended-chain polyethylene/epoxy composites are improved substantially when the fibres are pretreated in an ammonia plasma to introduce amine groups on to the fibre surface. These property changes are examined in terms of the microscopic properties of the fibre/matrix interface. Fracture surface micrographs show clean interfacial tensile and shear fracture in composites made from untreated fibres, indicative of a weak interfacial bond. In contrast, fracture surfaces of composites made from ammonia plasma-treated fibres exhibit fibre fibrillation and internal shear failure as well as matrix cracking, suggesting stronger fibre/matrix bonding, in accord with the observed increase in interlaminar fracture energy and shear strength. Failure of flexural test specimens occurs exclusively in compression, and the enhanced flexural strength and modulus of composites containing plasma-treated fibres result mainly from reduced compressive fibre buckling and debonding due to stronger interfacial bonding. Fibre treatment by ammonia plasma also causes an appreciable loss in the transverse ballistic impact properties of the composite, in accord with a higher fibre/matrix interfacial bond strength.     

Post-Impact Mechanical Characterisation of Glass and Basalt Woven Fabric Laminates

Two woven fabric laminates, one based on basalt fibres, the other on E-glass fibres, as a reinforcement for vinylester matrix, were compared in terms of their post-impact performance. With this aim, first the non-impacted specimens were subjected to interlaminar shear stress and flexural tests, then flexural tests were repeated on laminates impacted using a falling weight tower at three impact energies (7.5, 15 and 22.5J). Tests were monitored using acoustic emission analysis of signal distribution with load and with distance from the impact point. The results show that the materials have a similar damage tolerance to impact and also their post-impact residual properties after impact do not differ much, with a slight superiority for basalt fibre reinforced laminates. The principal difference is represented by the presence of a more extended delamination area on E-glass fibre reinforced laminates than on basalt fibre reinforced ones.     

Thermomechanical properties of bio-based composites made from a lactic acid thermoset resin and flax and flax/basalt fibre reinforcements

Low viscosity thermoset bio-based resin was synthesised from lactic acid, allyl alcohol and pentaerythritol. The resin was impregnated into cellulosic fibre reinforcement from flax and basalt and then compression moulded at elevated temperature to produce thermoset composites. The mechanical properties of composites were characterised by flexural, tensile and Charpy impact testing whereas the thermal properties were analysed by dynamic mechanical thermal analysis (DMTA) and thermogravimetric analysis (TGA). The results showed a decrease in mechanical properties with increase in fibre load after 40 wt.% for the neat flax composite due to insufficient fibre wetting and an increase in mechanical properties with increase fibre load up to 60 wt.% for the flax/basalt composite. The results of the ageing test showed that the mechanical properties of the composites deteriorate with ageing; however, the flax/basalt composite had better mechanical properties after ageing than the flax composite before ageing.     

Mechanical properties of chemically-treated hemp fibre reinforced sandwich composites

In this study, hemp fabrics were used as reinforcements with polyester resin to form composite skins while short hemp fibres with polyester as a core for making composite sandwich structures. To improve the fibre matrix adhesion properties, alkalisation, silane and acetylation treatments on the fibres surface were carried out. Examinations through fourier transform infrared (FTIR) spectroscopy, scanning electron microscope (SEM), differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) were conducted to investigate the physical and thermal properties of the fibres. Mechanical properties such as flexural and compressive strengths of the sandwich structures made by treated and untreated hemp fibres were studied. Based on the results obtained from the experiments, it was found that the fibre treated with alkalic solution and post-soaked by 8% NaOH exhibited better mechanical strength as compared with other treated and untreated fibre composite samples. Besides, DSC and TGA analysis showed that the thermal stability of all treated fibre was enhanced as compared with untreated samples.     

Mechanical performance optimization through interface strength gradation in PP/glass fibre reinforced composites

A new design for thermoplastic composites based on the gradation of the interlaminar interface strength (IGIS) has been developed with the aim of coupling high impact resistance with high static properties. IGIS laminates have been prepared by properly alternating layers of woven fabric with layers of compatibilized or not compatibilized polymeric films. To prove the new concept, polypropylene (PP) and glass fibres woven fabrics have been used to prepare composites by using the film stacking technique. Maleated PP, able to compatibilize polypropylene with glass fibres, has been used to manage the interface strength layer by layer.The flexural and low-velocity impact characterizations have shown that the presence of the coupling agent in conventional composite structures (prepared with fully compatibilized polymeric layers) improves the static flexural properties through the strengthening of the matrix/fibre interface but considerably lowers the low velocity impact resistance of the composite, in terms of maximum load before fibre breakage and recovered energy after impact. The use of the IGIS design, that grade the interface strength through the laminate thickness, allows to prepare composites with both high flexural properties and high impact resistance, without affecting the balance and type of the reinforcement configuration.     

Mechanical properties of carbon fibre-reinforced glasses

Carbon fibre-reinforced glasses exhibit very high values of flexural strength but usually a much less controlled fracture behaviour than SiC fibre-reinforced glasses. Some carbon fibre/glass composite combinations show a well controlled fracture, others a brittle fracture behaviour. The former combinations occasionally exhibit an increase in strength after an abrupt breakdown from the maximum strength. No correlation exists between the strength of the composites and the stresses in the glass matrix due to the thermal expansion mismatch between carbon fibres and glasses in contrast to the SiC fibre composites. The reason for that is seen in the structure of the surface and mainly in the anisotropic properties of the fibres, such as the large differences in the Young's moduli and thermal expansion coefficients parallel and perpendicular to the fibre axis. In particular, no radial compressive stress on the fibres can be built up at the fibre/glass interface because the thermal expansion coefficient of the fibres in the radial direction is much larger than that of the glass matrices used. Thus, the mechanism of load transfer from the matrix to the fibres is a complicated one, and cannot easily be predicted as in the case of the isotropic SiC fibres. A possible mechanism is described in order to interpret the experimental results.     

Fabrication and testing of natural fibre composites: Vakka, sisal, bamboo and banana

A study has been carried out to investigate the tensile, flexural and dielectric properties of composites made by reinforcing vakka as a new natural fibre into a polyester resin matrix. The fibres extracted by retting and manual processes have been used to fabricate the composites. These composites are tested for tensile, flexural and dielectric properties and compared with those of established composites like sisal, bamboo and banana made under the same laboratory conditions. The composites are fabricated up to a maximum volume fraction of fibre of 0.37 in the case of tensile testing, and 0.39 for flexural and dielectric testing. It has been observed that the tensile properties increase with respect to volume fraction of fibre for vakka fibre composite and are also more than those of sisal and banana composites and comparable to those of bamboo composites. The flexural strength of vakka fibre composite is more than that of banana composite and is closer to sisal fibre composite with respect to the volume fraction of fibre, where as the flexural modulus is much higher than those of banana and sisal fibre composites and also very much closer to bamboo fibre composites. The dielectric strength of vakka fibre composite increases with increase in volume fraction of fibre in the composite unlike the case of sisal, bamboo and banana composites. The dielectric strength being a unique feature of vakka fibre composite, can be suggested for electrical insulation applications.     

Evaluation of mechanical and thermal properties of banana–flax based natural fibre composite

Hybrid materials of any kind are the keynote for today’s demands. This paper deals with one of such hybrid composite made of natural fibres namely, banana and flax fibres. The structural build-up is such that one layer of banana fibre is sandwiched between two layers of flax fibres by hand layup method with a volume fraction of 40% using Epoxy resin and HY951 hardener. Glass fibre reinforcement polymer (GFRP) is used for lamination on both sides. This lamination also increases the overall mechanical properties along with better surface properties. The properties of this hybrid composite are determined by testing its tensile, impact, and flexural loads using a Universal testing machine. Thermal properties are analysed and hybrid composites of flax and banana with GFRP have better thermal stability and flame resistance over flax, banana with GFRP single fibre hybrid composites. Morphological analysis is done using Scanning Electron Microscope (SEM). The result of test shows that hybrid composite has far better properties than single fibre glass reinforced composite under impact and flexural loads. However it is found that the hybrid composite have better strength as compared to single fibre composites.     

Development of kenaf-glass reinforced unsaturated polyester hybrid composite for structural applications

The main aim of this paper is to develop kenaf-glass (KG) fibres reinforced unsaturated polyester hybrid composite on a source of green composite using sheet moulding compound process. Unsaturated polyester resin (UPE) and KG fibres in mat form were used at a ratio of 70:30 (by volume) with treated and untreated kenaf fibre. The kenaf fibre was treated with 6% sodium hydroxide (NaOH) diluted solution for 3 h using mercerization method. The hybrid composites were tested for flexural, tensile and Izod impact strength using ASTM D790-03, ASTM D618 and ASTM D256-04 standards respectively. The highest flexural, tensile and impact strength were obtained from treated kenaf with 15/15 v/v KG fibres reinforced UPE hybrid composite in this investigation.Scanning electron microscopy fractography showed fibre cracking, debonding and fibre pulled-out as the main fracture mode of composites and kenaf treated 15/15 v/v KG reinforced hybrid composite exhibited better interfacial bonding between the matrix and reinforcement compared to other combinations.     

The influence of fibre microstructure on fibre breakage and mechanical properties of natural fibre reinforced polypropylene

The aim of the study was to investigate the influence of fibre morphology of different natural fibres on the composites mechanical properties and on the fibre breakage due to extrusion process. The composite materials were manufactured using LTF (long fibre thermoplastic) extrusion and compression moulding and the used fibres were sisal, banana, jute and flax, and the matrix was a polypropylene. The results showed that sisal composites had the best impact properties and the longest fibres after the extrusion. Generally, the composites flexural stiffness was increased with increased fibre content for all fibres, being highest for flax composites. The flexural strength was not affected by the addition of fibres because of the low compatibility. The addition of 2 wt.% maleated polypropylene significantly improved the composites properties. Unlike the other three fibres, flax fibres were separated into individual elementary fibres during the process due to enzymatic retting and low lignin content.     

Experimental and theoretical studies on the properties of injection moulded glass fibre reinforced mixed plastics composites

Recycled mixed post-consumer and post-industrial plastic wastes consisting of HDPE, LDPE and PP were injection moulded with short glass fibre (10–30% by weight) to produce a new generation composite materials. Intensive experimental studies were then performed to characterise the tensile, compression and flexural properties of glass fibre reinforced mixed plastics composites. With the addition of 30 wt.% of glass fibre, the strength properties and elastic modulus increased by as much as 141% and 357%, respectively. The best improvement is seen in the flexural properties due to the better orientation of the glass fibres in the longitudinal direction at the outer layers. The randomness and length of the glass fibre were accounted to modify the existing rule of mixture and fibre model analysis to reliably predict the elastic and strength properties of glass fibre reinforced mixed plastics composites.     

Mechanical,thermal and morphological properties of a bio-based composite derived from banana plant source

This paper focuses on the synthesis and testing of a novel bio-based composite structure in which banana fibres was infused with resin made from banana sap. The mechanical, thermal, morphological and biodegradation properties of the bio-composite were characterized and it was found that the material was suitable for general non-functional components. Mechanical tests indicated 15% increase in tensile strength, 12% improvement in tensile modulus and a 25% improvement in flexural modulus when compared to structures produced without banana sap. At elevated temperatures a decrease in the moduli was observed. The thermal stability of the biocomposite composite improved and this corresponded with an increase in the glass transition temperature. Morphological studies using scanning electron microscopy revealed improved compatibility between the fibre and banana sap matrix. This resulted in improved dynamic modulus values and low damping values. Finally, degradation tests revealed increased microbial activity on the banana sap composite. This was indicative of improved biodegradation rates.     

Mechanical,rheological, morphological and water absorption properties of maleated polyethylene/hemp composites: Effect of ground tire rubber addition

Natural fibre composites were produced from maleated polyethylene (MAPE) and hemp fibres, while impact modification was performed via ground tire rubber (GTR) addition. Incorporation of hemp fibre increased significantly the tensile (strength and modulus) and flexural properties of the MAPE matrix. Impact strength however, decreased with increasing hemp content, but GTR addition led to a noticeable increase in impact strength (up to 50% at 10% GTR). Increase in hemp content produced also higher water uptake and longer saturation time. After ageing in water, the mechanical properties and thermal stability were unchanged for samples up to 30% hemp, but samples at higher concentrations showed some degradation.     

Plasma surface modification of advanced organic fibres: Part V Effects on the mechanical properties of aramid/phenolic composites

Aramid fibres have been treated in ammonia and oxygen plasma to enhance adhesion to resole phenolic resins. The plasma treatments resulted in significant improvements in interlaminar shear strength (ILSS) and flexural strength of composites made from these materials. Composites containing aramid fibres with epoxide groups reacted on to the ammonia plasma-treated fibre surface also showed further improvements in ILSS and flexural strength. Scanning electron and optical microscopic observations were used to examine the microscopic basis for these results, which have been compared with those obtained previously for aramid/epoxy and aramid/vinyl ester composites. For composites containing oxygen and ammonia plasma-treated fibres, the enhanced ILSS and flexural strength are attributed to improved wetting of the surface-treated aramid fibres by the phenolic resin. However, for those containing fibres with reacted epoxide groups on the ammonia plasma-treated fibre surfaces, the enhanced composite properties may be due to covalent chemical interfacial bonding between the epoxide groups and the phenolic resin. Effects of catalyst levels and cure cycle on the ILSS of composites laminated with untreated fabric has also been examined and optimum values have been determined. The catalyst concentration has an influence on the phase-separated water domain density in the matrix which in turn, affects the available fibre/matrix bonding area and hence the composite ILSS and flexural strength. This revised version was published online in November 2006 with corrections to the Cover Date.     

Mechanical properties of 3D KD-I SiCf/SiC composites with engineered fibre-matrix interfaces

Three-dimensional (3D) silicon carbide (SiC) matrix composites reinforced with KD-I SiC fibres were fabricated by precursor impregnation and pyrolysis (PIP) process. The fibre-matrix interfaces were tailored by pre-coating the as-received KD-I SiC fibres with PyC layers of different thicknesses or a layer of SiC. Interfacial characteristics and their effects on the composite mechanical properties were evaluated. The results indicate that the composite reinforced with as-received fibre possessed an interfacial shear strength of 72.1 MPa while the composite reinforced with SiC layer coated fibres had a much higher interfacial shear strength of 135.2 MPa. However, both composites showed inferior flexural strength and fracture toughness. With optimised PyC coating thickness, the interface coating led to much improved mechanical properties, i.e. a flexural strength of 420.6 MPa was achieved when the interlayer thickness is 0.1 μm, and a fracture toughness of 23.1 MPa m^1/2 was obtained for the interlayer thickness of 0.53 μm. In addition, the composites prepared by the PIP process exhibited superior mechanical properties over the composites prepared by the chemical vapour infiltration and vapour silicon infiltration (CVI-VSI) process.     

Effect of heat treatment in air on the structure and properties of barium osumilite reinforced with Nicalon fibres

Microstructural studies have been carried out on glass-ceramic matrix composites, consisting of barium osumilite reinforced with Nicalon fibres, which have been subjected to heat treatment in air in the range 600–1100 °C. Parallel studies have involved the measurement of the friction stress between fibre and matrix and the flexural strength of the composite. The matrix was shown to consist of barium osumilite, hexacelsian, mullite and a silica-rich glass, the thermal mismatch of these different phases leading to the development of appreciable strains. Whilst high-temperature treatments caused the formation of voids due to flow of the glassy phase, the major factor controlling the mechanical properties of the composite was the fibre/matrix interface. A change in microstructure, from a weak carbon-rich interface to one where the fibre and matrix were strongly bonded together by a silica layer, was thus reflected in an increase in the interfacial friction stress and a change in fracture behaviour from one showing fibre pull-out and delamination to one with brittle characteristics.