In vitro and in vivo adhesion testing of mucoadhesive drug delivery systems

Bioadhesive tablets were prepared by physical mixing of polymers and drug, then granulating and compressing into a tablet. The mucoadhesion was evaluated by shear stress measurement, detachment force measurement, and X-ray photography of the rabbit gastrointestinal tract. The strong interaction between the polymer and the mucous lining of the tissue helps increase contact time and permit localization. Polymers like hydroxypropyl methylcellulose K4M (HPMC K4M), hydroxypropyl methylcellulose 100 cps (HPMC 100 cps), carbopol-934, sodium carboxy methylcellulose (Na CMC), guar gum, and polyvinylpyrrolidone (PVP) were tested by shear stress measurement and detachment force measurement methods. HPMC K4M, showing maximum bioadhesion, was used in further studies. Adhesion was maximum between pH 5 and pH 6. Maximum adhesion was observed in the duodenum, followed by the jejunum and ileum. Barium sulfate (BaSO₄) matrix tablets containing polymer and drug were subjected to X-ray studies in rabbits, and it was found that the tablet was mucoadhesive even after 8 hr. Enteric coating did not show any effect on mucoadhesion after passing from the stomach.     

In-vitro evaluation of sustained-release dyphylline tablets

Dyphylline tablets were prepared by direct compression of mixtures of the drug, emcompress and different ratios of hydroxypropyl methylcellulose (HPMC) or cellulose acetate phthalate (CAP). Physical properties of the prepared tablets and the drug release in 0.1 N HC1 and phosphate buffer, pH 7.4 were investigated.

All tablets were found to satisfy the USP requirements regarding content, weight uniformity and friability. Hardness was greatly enhanced and thickness was slightly increased by increasing the polymer ratio in tablet formulations. Disintegration time of the dyphylline tablets was delayed by the presence of either HPMC or CAP and there was a direct relationship between the polymer ratio and the disintegration time. Considerable retardation in the rate and extent of drug release from the prepared tablets in both dissolution liquids was observed. As the polymer ratio increased in the tablet formulations, the drug release was significantly inhibited.     

Fabrication and in vitro evaluation of bidirectional release and stability studies of mucoadhesive donut-shaped captopril tablets

Objective: To obtain controlled release of captopril in the stomach, coated, mucoadhesive donut-shaped tablets were designed.

Materials and methods: Donut-shaped tablet were made of different ratios of diluents to polymer or combination of polymers by direct compression method. Top and bottom portions of the tablet were coated with water-insoluble polymer followed by mucoadhesive coating. Time of water penetration, measurement of tensile strength, mucoadhesion studies (static ex vivo and ex vivo wash-off) were taken into account for characterization of respective films. In vitro study has been performed at different dissolution mediums. Optimized batches were also prepared by wet granulation. Stability studies of optimized batches have been performed.

Results: The results of time of water penetration and tensile strength indicated positive response against water impermeation. Mucoadhesive studies showed that film thickness of 0.12?mm was good for retention of tablet at stomach. At pH 1.2, optimized batch of tablet made with hydroxypropyl methyl cellulose (HPMC) E15 as binder showed 80% w/w drug release within 4–5?h with maximum average release of 97.49% w/w. Similarly, maximum average releases of 96.36% w/w and 95.47% w/w were obtained with nearly same dissolution patterns using combination of HPMC E5 and HPMC E50 and sodium salt of carboxy methyl cellulose (NaCMC) 500–600 cPs instead of HPMC E15. The release profiles in the distilled water and pH 4.5 followed the above pattern except deviation at pH 6.8. Stability studies were not positive for all combinations.

Conclusion: Coated, mucoadhesive donut-shaped tablet is good for controlled release of drug in the stomach.     

Bioadhesive Tablets Influence of the Testing Medium Composition on Bioadhesion

A bioadhesive tablet of metronidazole has been developed for oral or vaginal administration. The bioadhesive component is poly(acrylic acid) (Carbopol 934), and the matrix component is hydroxypropyl methylcellulose (HPMC K4M). The influence of the test medium was investigated in order to determine the adhesion of the tablet during routine use by the various routes. The parameter retained to evaluate adhesion was the adhesion work on a biological tissue. The factors whose influence was investigated were pH, ionic force and nature of cations, and type of biological substrate     

Vitamin B12 buccoadhesive tablets: auspicious non-invasive substitute for intra muscular injection: formulation,in vitro and in vivo appraisal

Attempting to prepare a convenient bioavailable formulation of vitamin B₁₂ (cyanocobalamin), 17 tablet formulations were prepared by direct compression. Different concentrations of hydroxypropyl methyl cellulose (HPMC), carbopol 971p (CP971p), and chitosan (Cs) were used. The tablets were characterized for thickness, weight, drug content, hardness, friability, surface pH, in vitro drug release, and mucoadhesion. Kinetic analysis of the release data was conducted. Vitamin B₁₂ bioavailability from the optimized formulations was studied on rabbits by the aid of enzyme-linked immunosorbent assay. Neurotone^® I.M. injection was used for comparison. HPMC (F1-F4), CP971p (F5-F8), and HPMC/CP971p (F12-F15)-based formulations showed acceptable mechanical properties. The formulated tablets showed maximum swelling indices of 232?±?0.13. The surface pH values ranged from 5.3?±?0.03 to 6.6?±?0.02. Bioadhesive force ranged from 66?±?0.6 to 150?±?0.5?mN. Results showed that CP971p-based tablets had superior in vitro drug release, mechanical, and mucoadhesive properties. In vitro release date of selected formulations were fitted well to Peppas model. HPMC/CP971p-based formulations showed bioavailability up to 2.7-folds that of Neurotone^® I.M. injection.     

Hydroxypropyl methylcellulose mixtures: effects and kinetics of release of an insoluble drug

Matrix tablets manufactured from a practically insoluble drug using Methocel K4M, Methocel K100LV, and mixtures thereof exhibited non-Fickian dissolution properties governed by both diffusion and erosion (value of diffusional exponent in Peppas's transport equation 0.7). The effects of these two hydroxypropyl methylcellulose (HPMC) varieties were nonlinear and antagonistic.     

Bioadhesive Tablets Influence of the Testing Medium Composition on Bioadhesion

Abstract

A bioadhesive tablet of metronidazole has been developed for oral or vaginal administration. The bioadhesive component is poly(acrylic acid) (Carbopol 934), and the matrix component is hydroxypropyl methylcellulose (HPMC K4M). The influence of the test medium was investigated in order to determine the adhesion of the tablet during routine use by the various routes. The parameter retained to evaluate adhesion was the adhesion work on a biological tissue. The factors whose influence was investigated were pH, ionic force and nature of cations, and type of biological substrate     

Formulation and In Vitro Studies of a Fixed-Dose Combination of a Bilayer Matrix Tablet Containing Metformin HCl as Sustained Release and Glipizide as Immediate Release

The emerging new fixed dose combination of metformin hydrocholride (HCl) as sustained release and glipizide as immediate release were formulated as a bilayer matrix tablet using hydroxy propyl methyl cellulose (HPMC) as the matrix-forming polymer, and the tablets were evaluated via in vitro studies. Three different grades of HPMC (HPMC K 4M, HPMC K 15M, and HPMC K 100M) were used. All tablet formulations yielded quality matrix preparations with satisfactory tableting properties. In vitro release studies were carried out at a phosphate buffer of pH 6.8 with 0.75% sodium lauryl sulphate w/v using the apparatus I (basket) as described in the . The release kinetics of metformin were evaluated using the regression coefficient analysis. There was no significant difference in drug release for different viscosity grade of HPMC with the same concentration. Tablet thus formulated provided sustained release of metformin HCl over a period of 8 hours and glipizide as immediate release.     

Influence of soluble and insoluble cyclodextrin polymers on drug release from hydroxypropyl methylcellulose tablets

Background: The influence of β-cyclodextrin (β-CD) polymers on drug release from hydroxypropyl methylcellulose (HPMC) matrices has not been reported in the literature. Aim: The influence of monomeric β-CD and both soluble and insoluble β‐CD polymers on drug release from tablets containing either 30% or 50% hydroxypropyl methylcellulose has been studied using diflunisal (DF) as model drug. Method: The DF-β-CD inclusion complex (1:1 M) was prepared by coevaporation and characterised using X-ray diffraction, differential thermal analysis, and IR spectroscopy. The dissolution assays were performed according to the USP paddle method. Results: The incorporation of β-CD in the complexed form increases drug release from hydroxypropyl methylcellulose tablets in comparison with the physical mixture because of the better solubilization of the drug. The soluble polymer promotes drug release to a higher extent than the physical mixture with monomeric β-CD, but the insoluble polymer, which is itself a hydrogel, gives rise to the most retarded release profile, probably by retention of the drug in its structure. The formulations containing physical mixtures with either β‐CD or the soluble polymer present an optimum adjustment to zero-order release kinetics, and the inclusion complex followed non-Fickian diffusion according to the Korsmeyer–Peppas model. Conclusion: The release profile of DF from a HPMC matrix can be modulated in different ways by the use of either monomeric or polymeric β-CD.     

Oral Sustained Delivery of Atenolol from Floating Matrix Tablets—Formulation and In Vitro Evaluation

Floating matrix tablets of atenolol were developed to prolong gastric residence time and increase drug bioavailability. Atenolol was chosen as a model drug because it is poorly absorbed from the lower gastrointestinal tract. The tablets were prepared by direct compression technique, using polymers such as hydroxypropyl methylcellulose (HPMC K15M, K4M), guargum (GG), and sodium carboxymethylcellulose (SCMC), alone or in combination, and other standard excipients. Tablets were evaluated for physical characteristics viz. hardness, swelling index, floating capacity, thickness, and weight variation. Further, tablets were evaluated for in vitro release characteristics for 8 hr. The effect of effervescent on buoyancy and drug release pattern was also studied. In vitro release mechanism was evaluated by linear regression analysis. GG- and SCMC-based matrix tablets showed significantly greater swelling indices compared with other batches. The tablets exhibited controlled and prolonged drug release profiles while floating over the dissolution medium.     

Optimization of piribedil mucoadhesive tablets for efficient therapy of Parkinson’s disease: physical characterization and ex vivo drug permeation through buccal mucosa

Objective: The aim of this study was optimization of buccal piribedil (PR) mucoadhesive tablets to improve its low bioavailability and provide controlled release for the treatment of Parkinson’s disease.

Methods: Buccal tablets were prepared by direct compression method using carbomer (CP), carboxymethyl cellulose (CMC), and hydroxypropyl methylcellulose (HPMC) as mucoadhesive polymers. Physical properties of powder mixtures and buccal tablets were evaluated. Physicochemical compatibility between ingredients was investigated with infrared spectroscopy and differential scanning calorimetry analysis. In vitro dissolution profiles and drug release kinetics of buccal tablets were investigated. Mucoadhesion and ex vivo permeation studies were performed using sheep buccal mucosa.

Results: Powder mixtures demonstrated sufficient flow properties and physical characteristics of all tablet formulations were within compendia limits. Tablet ingredients were absent of any chemical interactions. CP tablets displayed slower drug release compared to HPMC tablets with zero order release, while CMC tablets lost their integrity and released entire drug after 6?h following Higuchi model. All formulations displayed adequate mucoadhesion and steady state flux of PR through buccal mucosa were higher with HPMC compared to CP-containing tablets.

Conclusion: Overall, HPMC was found to combine desired controlled release and mucoadhesion characteristics with sufficient pharmaceutical quality for optimization of buccal tablets. Piribedil mucoadhesive buccal tablets designed for the first time may introduce a new alternative for the treatment of Parkinson’s disease.     

Hydroxypropyl Methylcellulose Mixtures: Effects and Kinetics of Release of an Insoluble Drug

Matrix tablets manufactured from a practically insoluble drug using Methocel K4M, Methocel K100LV, and mixtures thereof exhibited non-Fickian dissolution properties governed by both diffusion and erosion (value of diffusional exponent in Peppas's transport equation 0.7). The effects of these two hydroxypropyl methylcellulose (HPMC) varieties were nonlinear and antagonistic.     

Influence of hydroxypropyl methylcellulose mixture,apparent viscosity,and tablet hardness on drug release using a 2(3) full factorial design

This study investigates the effects of three factors: (1) use of a mixture of two different grades of hydroxypropyl methylcellulose (HPMC), (2) apparent viscosity, and (3) tablet hardness on drug release profiles of extended-release matrix tablets. The lot-to-lot apparent viscosity difference of HPMC K15M on in vitro dissolution was also investigated. Four test formulations were made, each containing 10% of a very water-soluble active pharmaceutical ingredient (API), 32% HPMC K15M, or a mixture of HPMC K100LV and HPMC K100M, 56% diluents, and 2% lubricants. Each formulation was made at two hardness levels. A 2³ full factorial design was used to study various combinations of the three factors using eight experiments conducted in a randomized order. Dissolution studies were performed in USP apparatus I. The values of t_50% (time in which 50% drug is released) and t_lag (lag time, the time taken by the matrix tablet edges to get hydrated and achieve a state of quasi-equilibrium before erosion and the advance of solvent front through the matrix occur) were calculated from each dissolution profile. The similarity factor (f₂) was also calculated for each dissolution profile against the target dissolution profile. A simple Higuchi-type equation was used to analyze the drug release profiles. Statistical analysis using analysis of variance (ANOVA) and similarity factor (f₂) values calculated from the data indicated no significant difference among the t_50% values and dissolution profiles respectively for all formulations. Within the 3.3-6 kp hardness range investigated, dissolution rates were found to be independent of tablet hardness for all the formulations. Although significantly shorter lag times were observed for the tablets formulated with low- and high-viscosity HPMC mixtures in comparison to those containing a single grade of HPMC, this change had no significant impact on the overall dissolution profiles indicated by the similarity factor f₂ values. From this study it can be concluded that lot-to-lot variability in apparent viscosity of HPMC should not be a concern in achieving similar dissolution profiles. Also, results indicated that within the viscosity range studied (12,000-19,500 cps) an HPMC mixture of two viscosity grades can be substituted for another HPMC grade if the apparent viscosity is comparable. Also, the drug release is diffusion-controlled and depends mostly on the viscosity of the gel layer formed.     

Formulation and Evaluation of Methocel K15M Bioadhesive Matrix Tablets

Methocel K15M is a bioadhesive polymer. Its adhesion and bioadhesion characteristics were evaluated by shear stress measurement and detachment force measurement methods, respectively. The effect of pH on adhesion was studied, and it was found that the maximum adhesion was between pH 5 and pH 6. Adhesion strength at different parts of the sheep intestine was studied; in the duodenal portion of the intestine, the adhesion was maximum. Chlorpheniramine maleate and diclofenac sodium drugs are formulated with Methocel K15M as matrix tablets. In vitro release studies revealed that some of the formulations showed initial first-order behavior followed by zero-order release behavior.     

Formulation and evaluation of Methocel K15M bioadhesive matrix tablets

Methocel K15M is a bioadhesive polymer. Its adhesion and bioadhesion characteristics were evaluated by shear stress measurement and detachment force measurement methods, respectively. The effect of pH on adhesion was studied, and it was found that the maximum adhesion was between pH 5 and pH 6. Adhesion strength at different parts of the sheep intestine was studied; in the duodenal portion of the intestine, the adhesion was maximum. Chlorpheniramine maleate and diclofenac sodium drugs are formulated with Methocel K15M as matrix tablets. In vitro release studies revealed that some of the formulations showed initial first-order behavior followed by zero-order release behavior.     

The Effect of Processing Variables on the Release of Ibuprofen and Caffeine from Controlled-Release Nonswellable Core-in-Cup Compressed Tablets

Abstract

An aqueous soluble polymer such as hydroxypropyl methylcellulose (HPMC), which is widely used in oral sustained-release drug delivery systems, swells when it comes into contact with an aqueous environment. In core-in-cup systems the swelling of the HPMC splits open the cup portion of the tablet. This study investigated the use of acacia, tragacanth, polyethylene glycol 6000 (PEG 6000), and hydroxyethyl-cellulose (HEC) as possible alternatives to the use of HPMC to control the release of caffeine (soluble) and ibuprofen (insoluble) from core-in-cup compressed tablets. It also investigated the possibility of producing a core-in-cup system that had the ability to release caffeine and ibuprofen for a maximum time of constant release of 8-12 hr. A preliminary study revealed that acacia was most effective for the release of caffeine from the core-in-cup compressed tablets, and that PEG 6000 was most effective for the release of ibuprofen from the core-in-cup compressed tablets. On further investigation it was found that by means of adjusting the hardness of compression and the concentration of polymers used, it was possible to formulate a core-in-cup system that could release drug at a constant rate from the core-in-cup compressed tablets for 8 to 12 hr.     

Effect of excipient and processing variables on adhesive properties and release profile of pentoxifylline from mucoadhesive tablets

The bioavailability and onset of action of drugs with high first-pass metabolism can be significantly improved by administration via the sublingual route. The objective of this study was to evaluate the effect of polymer type and tablet compaction parameters on the adhesive properties and drug release profile from mucoadhesive sublingual tablet formulations. Pentoxifylline was selected as the model drug because it has poor oral bioavailability due to extensive first-pass metabolism. Two polymers known to possess mucoadhesive properties, carbomer and hydroxypropyl methyl cellulose (HPMC), were used to prepare the formulations. Tablets were prepared by using direct compression technique and evaluated for in vitro dissolution, drug-excipient interactions, and adhesive properties. In general, there was a decrease in the rate of drug release with an increase in the concentration of polymers. No drug-excipient interactions were evident from differential scanning calorimetry or high-performance liquid chromatography analysis. For the formulations containing HPMC, the force of mucoadhesion increased with an increase in the concentration of polymer; however, for carbomer formulations, no such correlation was observed. Force of mucoadhesion decreased as a function of hydration time in both of the polymers.     

The Effect of Processing Variables on the Release of Ibuprofen and Caffeine from Controlled-Release Nonswellable Core-in-Cup Compressed Tablets

An aqueous soluble polymer such as hydroxypropyl methylcellulose (HPMC), which is widely used in oral sustained-release drug delivery systems, swells when it comes into contact with an aqueous environment. In core-in-cup systems the swelling of the HPMC splits open the cup portion of the tablet. This study investigated the use of acacia, tragacanth, polyethylene glycol 6000 (PEG 6000), and hydroxyethyl-cellulose (HEC) as possible alternatives to the use of HPMC to control the release of caffeine (soluble) and ibuprofen (insoluble) from core-in-cup compressed tablets. It also investigated the possibility of producing a core-in-cup system that had the ability to release caffeine and ibuprofen for a maximum time of constant release of 8-12 hr. A preliminary study revealed that acacia was most effective for the release of caffeine from the core-in-cup compressed tablets, and that PEG 6000 was most effective for the release of ibuprofen from the core-in-cup compressed tablets. On further investigation it was found that by means of adjusting the hardness of compression and the concentration of polymers used, it was possible to formulate a core-in-cup system that could release drug at a constant rate from the core-in-cup compressed tablets for 8 to 12 hr.     

Formulation and in vitro studies of a fixed-dose combination of a bilayer matrix tablet containing metformin HCl as sustained release and glipizide as immediate release

The emerging new fixed dose combination of metformin hydrocholride (HCl) as sustained release and glipizide as immediate release were formulated as a bilayer matrix tablet using hydroxy propyl methyl cellulose (HPMC) as the matrix-forming polymer, and the tablets were evaluated via in vitro studies. Three different grades of HPMC (HPMC K 4M, HPMC K 15M, and HPMC K 100M) were used. All tablet formulations yielded quality matrix preparations with satisfactory tableting properties. In vitro release studies were carried out at a phosphate buffer of pH 6.8 with 0.75% sodium lauryl sulphate w/v using the apparatus I (basket) as described in the United States Pharmacopeia (2000). The release kinetics of metformin were evaluated using the regression coefficient analysis. There was no significant difference in drug release for different viscosity grade of HPMC with the same concentration. Tablet thus formulated provided sustained release of metformin HCl over a period of 8 hours and glipizide as immediate release.     

Mucoadhesive delivery systems. I. Evaluation of mucoadhesive polymers for buccal tablet formulation

Different types of mucoadhesive polymers, intended for buccal tablet formulation, were investigated for their comparative mucoadhesive force, swelling behavior, residence time and surface pH. The selected polymers were carbopols (CP934, and CP940), polycarbophil (PC), sodium carboxymethyl cellulose (SCMC) and pectin representing the anionic type, while chitosan (Ch) as cationic polymer and hydroxypropylmethyl cellulose (HPMC) as a non-ionic polymer. Results revealed that polyacrylic acid derivatives (PAA) showed the highest bioadhesion force, prolonged residence time and high surface acidity. SCMC and chitosan ensured promising bioadhesive characteristics, whilst HPMC and pectin exhibited weaker bioadhesion. Different polymer combinations as well as formulations were evaluated to improve the mucoadhesive performance of the tablets. Bioadhesive tablet formulations containing either 5% CP934, 65% HPMC and 30% spray-dried lactose or 2% PC, 68% HPMC and 30% mannitol showed optimum mucoadhesion and suitable residence time. SCMC, when formulated individually, exhibited promising bioadhesion, acceptable swelling, convenient residence time and surface pH. In-vivo trials of these formulations proved non-irritative and prolonged residence of the mucoadhesive tablets on human buccal mucosa for 8 to 13 h.