共查询到20条相似文献,搜索用时 171 毫秒
1.
2.
3.
4.
铝合金化学镀镍磷合金镀层的组织和相结构 总被引:3,自引:1,他引:3
介绍了铝合金化学镀镍磷合金镀层的初期析出行为、组织和相结构。镀态下,镀层截面组织为黑白分明的层状组织,平面组织呈同心环状。低磷镀层的相结构是磷在镍中的过饱和固溶体,而高磷镀层为非晶态镍磷合金。随着加热温度的升高,低磷镀层的相结构是磷在镍中的过饱和固溶体,而高磷镀层为非晶态镍磷合金。随着加热温度的升高,低磷镀层首先析出NixPy,然后析出Ni3P相。高磷非晶态镀层首先晶化转变成NixPy相和Ni3P 相似文献
5.
6.
7.
8.
化学镀镍磷合金的动力学研究 总被引:2,自引:0,他引:2
在考察乳酸体系化学镀镍磷合金各反应物浓度、镀液的pH值和温度等因素对沉积速度影响的基础上,根据原子氢理论和实验规律,分析化学镀镍磷合金的反应过程,进行反应动力学研究,分别确定上述各因素所对应的反应动力学参数,提出化学镀镍磷合金的反应速度方程.由实验得出化学镀温度与反应速度的关系,通过该反应速度方程可预测出在乳酸体系镀液中的镀层沉积速度. 相似文献
9.
化学镀镍磷合金技术在防蚀领域巳被广泛的采用。本文重点介绍镀镍一磷合金镀层的组成、结构与防蚀性能之间的关系。以便根据实际应用的要求造择台适的镀层组成和相应的工艺。 相似文献
10.
11.
铝合金化学镀Ni-P合金层及其耐蚀性研究 总被引:6,自引:2,他引:4
为进一步提高2024铝合金的耐蚀性,采用化学镀技术在铝合金表面沉积了Ni-P合金层,用扫描电镜观察镀层的表面形貌,通过开路电位、动电位极化和交流阻抗等电化学测试方法对比了镀层和2024铝合金在3.5%NaCl溶液中的耐蚀性。结果表明:通过该工艺可以在铝合金表面沉积一层致密的Ni-P层,镀层的自腐蚀电位比基体更正,自腐蚀电流密度更低,铝合金的耐蚀性得到提高。 相似文献
12.
铝合金化学镀镍工艺对镀层沉积速度的影响 总被引:2,自引:0,他引:2
针对铝合金的特点,采用一种无机酸处理工艺对铝合金进行前处理,然后直接进行化学镀镍。讨论了主盐、还原剂、络合剂、pH值等因素对化学镀镍反应沉积速度的影响,得到了较优的工艺配方。验证试验所得Ni-P合金镀层表面均匀,耐蚀性好,结合力强。 相似文献
13.
2024铝合金表面化学镀镍工艺研究 总被引:1,自引:0,他引:1
通过正交实验确定了2024铝合金表面化学镀镍合金层的镀液组成,并通过扫描电镜对镀层的表面形貌进行了观察,通过交流阻抗对镀层在3.5%NaCl溶液的耐蚀性进行了测试。实验结果表明,采用本溶液组成和工艺可以制备表面均匀平整、致密的Ni-P合金层,镀层与基体结合良好。同时,镀层的显微硬度约是基体的8.5倍,耐蚀性得到明显改善,具有良好的工业应用前景。 相似文献
14.
Effects of zincate treatment on adhesion of electroless Ni-P coating onto various aluminum alloys 总被引:1,自引:0,他引:1
The effects of alloying elements on zincate treatment and adhesion of electroless Ni-P coating onto various aluminum alloy substrates were examined. Surface morphology of zinc deposits in the 1st zincate treatment and its adhesion were changed depending on the alloying element. The zinc deposits in the 2nd zincate treatment became thinly uniform, and the adhesion between aluminum alloy substrate and Ni-P coating was improved irrespective of the alloying element. XPS analysis revealed the existence of zinc on the surface of each aluminum alloy substrate after the pickling in 5% nitric acid. This zinc on the surface should be an important factor influencing the morphology of zinc deposit at the 2nd zincate treatment and its adhesion. 相似文献
15.
16.
铝合金化学镀Ni-P前处理工艺条件的优化 总被引:3,自引:2,他引:1
化学镀Ni-P可以改善铝合金易产生晶间腐蚀、表面硬度低、不耐磨损等缺陷,欲使镀层与铝合金基体具有很好的结合力,前处理工艺则显得尤为重要。采用正交试验,用极差法分析了活化和预镀镍各工艺参数对后续化学镀Ni-P镀速影响的主次顺序,确定了活化和预镀镍镀液的最佳配方及各工艺条件,并利用金相显微镜、扫描电镜能谱、增重法、热震实验和失重法等测试了采用最佳活化、预镀镍工艺所得镀层的形貌和性能,结果表明:所确定的活化、预化学镀镍前处理工艺可显著提高镀层的硬度、沉积速率及其与基体的结合强度,镀层组织致密均匀,耐蚀性优良。 相似文献
17.
飞机结构铝合金直接化学镀Ni-P合金研究 总被引:2,自引:0,他引:2
高强度铝合金被广泛用于飞机结构中,然而,这一系列铝合金抗腐蚀和耐磨性差,限制了其应用。而Ni-P合金镀层具有高的硬度和抗腐蚀性能等优异特点,成为增强表面性能的常用手段。采用化学镀镍工艺在铝合金(6061)表面进行化学镀镍处理,研究了pH值、沉积温度和沉积时间对沉积速率的影响。分析了化学镀镍层的成分和组织形貌,同时对镀层的硬度、抗腐蚀性进行了表征。试验表明,在铝合金表面化学镀镍可以显著提高铝合金表面的硬度,并改善其在5%NaCl溶液中的耐蚀性。 相似文献
18.
Lijian Gu Xiaolong Chen Xizhi FanYangjia Liu Binglin ZouYing Wang Xueqiang Cao 《Surface & coatings technology》2011,206(1):29-36
NiCoCrAlY/8YSZ coating was firstly directly deposited on aluminum alloy 5A06 by atmospheric plasma spray to make it applicable to short-time high temperature condition. The failure after thermal shock test was mainly due to the stress caused by thermal expansion mismatch between the bond coat and the substrate as well as the galvanic corrosion of the aluminum alloy. Ni-P, Ni-W-P and Ni-Cu-P as interlayers were electrolessly deposited on the substrate in order to mitigate the thermal stress. The composition and thermal transformation of the interlayers were investigated. Thermal shock resistance and bonding strength of multilayer coatings (interlayer/NiCoCrAlY/8YSZ) were tested. Diffusion layers mainly composed of AlNi, Al3Ni2 and Al3Ni were observed between the interlayers and the substrate after thermal shock test. The oxidation of the substrate was effectively inhibited. Ni-P interlayer obtained at lower pH value was superior to the other two interlayers and enhanced the thermal shock life from 38 to more than 200 cycles. With the application of the Ni-P and Ni-Cu-P interlayers, the bonding strength examined by pull-off test was also largely improved from 11.7 MPa to 18.8 and 19.0 MPa, respectively. 相似文献
19.
20.
钨铜合金表面化学镀Ni-P镀层性能研究 总被引:2,自引:0,他引:2
从钨铜合金表面化学镀Ni-P镀层的表面形貌及成分,镀层结构,外观,结合力.硬度,耐磨性,孔隙率,纤焊性等方面进行了检测和表征.结果表明,化学镀Ni-P合金层磷含量为11.37%,属于高磷镀层,主要为非晶型结构,在钨铜合金表面化学镀Ni-P合金可以大大提高钨铜合金的硬度和耐磨性,且Ni-P合金镀层与钨铜合金基体结合强度好,孔隙率低,纤焊性好. 相似文献