Effect of styrene–ethylene–butadiene–styrene and its synergetic effect with ethylene vinyl acetate on the mechanical,thermal, dielectric,and water‐treeing behaviors of crosslinked polyethylene

In this study, we investigated the effect of an aromatic polymer, styrene–ethylene–butadiene–styrene (SEBS), on the water‐tree resistance of crosslinked polyethylene (XLPE), and the synergetic effect of SEBS and ethylene vinyl acetate (EVA) was also investigated. The XLPE/SEBS and XLPE/SEBS/EVA samples were characterized by means of differential scanning calorimetry, scanning electron microscopy, mechanical measurements, and an accelerated water‐treeing experiment, and the obtained results clearly show the relevant influence of SEBS and EVA, and as expected, the addition of SEBS and EVA was found to synergistically influence the water‐tree resistance of XLPE more positively in comparison with that without the addition of EVA. In addition, it also indicated that the blends possessed excellent dielectric behaviors, such as the dielectric constant and dissipation factor. The crystallization of the blends decreased with increasing SEBS content and addition of EVA. However, the melting temperature of the blends increased with the addition of SEBS and EVA, but the melting temperature of the blends decreased with increasing SEBS content. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Ethylene vinyl acetate and ethylene vinyl alcohol copolymer for thermal spray coating application

Ethylene vinyl acetate (EVA) copolymer with varying vinyl acetate (VAc) content, viz. 18%, 28% and 40% has been hydrolyzed using alcoholic NaOH solution. Fourier Transform Infrared Spectroscopy (FTIR) analyses of hydrolyzed polymer showed the presence of both OH group and acetate group indicating that the EVA has been partially hydrolyzed. Differential Scanning Calorimeter (DSC) and Thermo Gravimetric Analyzer (TGA) of EVA and hydrolyzed EVA showed large difference in melting and decomposition temperature, respectively. Hydrolyzed EVA showed higher tensile strength and elongation at break compared to corresponding EVA. Blends of different grades of EVA and ethylene vinyl alcohol (EVAl) with low density polyethylene (LDPE) were applied on grit blasted mild steel surface by flame spray technique. FTIR analysis of blends before and after coating showed no degradation during flame spray. Measurement of adhesion strength of these coating showed that adhesion strength increased on hydrolysis of EVA.     

Toughening effects of ethylene–vinyl acetate copolymers with different vinyl acetate content and viscosity on nylon 1010 blends

Nylon 1010 blends with ethylene–vinyl acetate copolymer (EVA) and maleated ethylene–vinyl acetate (EVA‐g‐MAH) were prepared through melt blending. The vinyl acetate (VA) content and viscosity of EVA significantly affected the notched impact strength of nylon/EVA/EVA‐g‐MAH (80/15/5) blends. The nylon/EVA/EVA‐g‐MAH blends with high notched impact strength (over 60 kJ/m²) were obtained when the VA content in EVA ranged from 28 to 60 wt%. The effect of VA content on the notched impact strength of blends was related to the glass transition temperature for EVA with high VA content and crystallinity for EVA with low VA content. For nylon blends with EVA with the same VA content, low viscosity of EVA led to high notched impact strength. Fracture morphology of nylon/EVA/EVA‐g‐MAH (80/15/5) blends showed that blends with ductile fracture behavior usually had large matrix plastic deformation, which was the main energy dissipation mechanism. A relationship between the notched impact strength and the morphology of nylon/EVA/EVA‐g‐MAH (80/15/5) blends was well correlated by the interparticle distance model. POLYM. ENG. SCI., 2009. © 2009 Society of Plastics Engineers     

Cure characteristics,morphology, mechanical properties,and aging characteristics of silicone rubber/ethylene vinyl acetate blends

Silicone rubber/ethylene vinyl acetate (SR/EVA) rubber mixes with different ratios were prepared by using dicumyl peroxide (DCP) and benzoyl peroxide (BP) as curing agents. The vulcanization characteristics such as cure kinetics, activation energy, and cure rate of the blends were analyzed. The effects of blend ratio and curing agents on the mechanical properties such as stress–strain behavior, tensile strength, elongation at break, tear strength, relative volume loss, hardness, flex crack resistance, and density of the cured blends have been investigated. Almost all the mechanical properties have been found to be increased with increase in EVA content in the blends particularly in DCP‐cured systems. The increment in mechanical properties of the blends with higher EVA content has been explained in terms of the morphology of the blends, attested by scanning electron micrographs. Attempts have been made to compare the experimental results, from the evaluation of mechanical properties, with relevant theoretical models. The aging characteristics of the cured blends were also investigated and found that both the DCP‐ and BP‐cured blends have excellent water and thermal resistance. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 1069–1082, 2006     

Combined effect of VA content and pH level of filler on properties of EPDM/SmBO3 and EPDM/ATO composites reinforced by three types of EVA

This study investigates the interaction of vinyl acetic (VA) content of ethylene‐vinyl acetate (EVA), pH level of Samarium borate (SmBO₃), and Sb‐doped SnO₂ (ATO) on reinforcement of peroxide‐cured ethylene‐propylene‐diene rubber (EPDM)/SmBO₃ and EPDM/ATO composites. It was found that EVA could both reinforce mechanical properties of EPDM, and enhance fluidity of gum during processing. During vulcanization, the interaction of VA groups and pH value of filler particles can influence the crosslink density of EPDM composites. In alkaline EPDM/SmBO₃/EVA, VA groups could hydrolyze to produce polyvinyl alcohol and reduce pH level of medium by consuming OH⁻. When dispersed in acidic EPDM/ATO/EVA, VA groups could generate polyunsaturated bonds and acetic acid during vulcanization. The double bonds could react with dicumyl peroxide (DCP) and then boost crosslink efficiency of EPDM composites. Moreover, acetic acid and reduction of pH value could make DCP decompose into ions, and lower crosslink density of EPDM composites. In addition to the contribution of crosslink density, EVA could crystallize in EPDM composites to reinforce EPDM composites. Electric properties of EPDM were also affected. Surface and volume resistivity of EPDM composites decreased with the rise of VA content. As for EPDM/SmBO₃/EVA composites, the growth of VA groups could boost dielectric constant and loss, decrease dielectric strength, due to the enhancement of polarity and reduction of crosslink density. In terms of EPDM/ATO/EVA composites, the EPDM/ATO/EVA14 possesses the highest dielectric constant and loss, and the lowest dielectric strength, because of the competing effect of VA content and crosslink density. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Mechanical,Thermal and Electrical Properties of Ethylene Vinyl Acetate Irradiated by an Electron-Beam

The effects of electron beam irradiation of (ethylene vinyl acetate) EVA containing 18% vinyl acetate was studied. The EVA sample was then irradiated by using 3 MeV electron beam machine at doses ranging from 120 to 360 kGy in air at room temperature and analyzed for mechanical, thermal and electrical properties. It was revealed by DSC analysis that the crystallinity of the electron-beam radiated EVA decreased slightly as verified by a marginal reduction in the densities and heats of melting. Thermal degradation of EVA occurred through two steps as shown by the thermogravimetric curve with maximum rates of 350 and 450°C, respectively. The results obtained from both gel content and hot set tests showed that under the irradiation conditions employed, the EVA sample cross-linked by the electron beam irradiation, and the degree of cross-linking in the amorphous regions was dependent on the irradiation dose. A significant improvement in the tensile strength of the neat EVA samples was obtained upon electron-beam radiation up to 210 kGy with a concomitant decline in elongation of break. Various electrical properties of EVA such as surface and volume resistance, breakdown voltage and dielectric constant were studied as a function of radiation dose. It was revealed that the surface resistance and volume resistivity of the EVA reaches a maximum at a 190 kGy dose of radiation. No considerable change of breakdown voltage and dielectric constant was observed with increasing irradiation dose. These studies suggest that radiation-cured EVA is more thermally and mechanically stable than pure EVA. Similarly, the results from the electrical properties revealed that surface and volume resistance are higher than pure EVA.     

Multiwalled carbon nanotube/montmorillonite hybrid filled ethylene‐co‐vinyl acetate nanocomposites with enhanced mechanical properties,thermal stability,and dielectric response

Homogeneous multiwalled carbon nanotube/montmorillonite hybrid filler (HMM) dispersion was prepared by co‐ultrasonication and was subsequently used to prepare ethylene‐co‐vinyl acetate (EVA) nanocomposites by solution blending method. XRD and TEM analysis of HMM confirm significant interaction between the montmorillonite (MMT) layers and multiwalled carbon nanotubes (MWCNT) in line with previous reports. Analysis of the nanocomposites shows the constituent fillers to be homogeneously dispersed in EVA matrix. Mechanical properties of neat EVA are remarkably improved with HMM content up to 3 wt% followed by reversion. Maximum improvement observed in tensile strength, elongation at break, and toughness are 424%, 109%, and 1122%, respectively. Results show maximum thermal stability at 4 wt% and best dielectric response at 1 wt% HMM content. Exceptional mechanical and dielectric properties of EVA nanocomposites attained may be attributed to homogeneous dispersion of fillers and improved polymer–filler interaction. Comparison shows excellent synergy between MWCNT and MMT towards mechanical reinforcement of EVA. POLYM. ENG. SCI., 58:1155–1165, 2018. © 2017 Society of Plastics Engineers     

Dynamic–mechanical properties of modified poly(ethylene‐co‐vinyl acetate)

To study the relationship among relaxation peaks observed in dynamic mechanical experiments and the structure of poly(ethylene‐co‐vinyl acetate) (EVA), EVA copolymers with different substitution in the carbonyl group were synthesized. EVA was hydrolyzed to obtain poly (ethylene‐co‐vinyl alcohol) and was subsequently reacted with formic, hexanoic, and octanoic acids. The copolymers synthesized were characterized by infrared spectroscopy. Analysis of the DMA spectra of the copolymers showed that their relaxation behavior depends on the vinyl acetate concentration. The α‐ and β‐transitions were observed in EVA copolymers with 8 and 18 wt % of functional groups, and the relationship among relaxation process with the structure of polymer was investigated. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 1371–1376, 2005     

Effect of the elastomer type on the microstructure and mechanical properties of polypropylene

In this study, the effects of the elastomer type—ethylene–propylene–diene monomer (EPDM), three kinds of ethylene vinyl acetate (EVA 9, EVA 18, and EVA 28, where the number is the vinyl acetate concentration), and styrene–butadiene–styrene—and content on the microstructure and mechanical and thermal properties of isotactic polypropylene (i‐PP) blends were investigated. Five different elastomer concentrations (3, 6, 9, 12, and 15 wt %) were added to i‐PP to produce polypropylene/elastomer blends. The yield and tensile strengths, elastic modulus, impact strength, hardness, melt flow index (MFI), and structural properties of the blends were investigated. The tensile and yield strengths, elastic modulus, and hardness decreased gradually, whereas the impact strength and MFI increased as the elastomer content increased. As a result, with respect to the impact strength, the most effective elastomers were EPDM with 15 wt % and EVA 28 with 15 wt % for higher impact strength values. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 1445–1450, 2005     

Radiation grafting of poly(ethylene terephthalate) (PET) fibre,II. Hydrolysis of grafted poly(vinyl acetate) to poly(vinyl alcohol)

Poly(ethylene terephthalate) fibres grafted with poly(vinyl acetate) by γ-radiation were hydrolysed under alkaline and acidic conditions in order to obtain poly(ethylene terephthalate)-graft-poly(vinyl alcohol) fibres. In alkaline media poly(ethylene terephthalate) degraded without appreciable conversion of acetate to hydroxyl groups. During acid hydrolysis no change in tensile properties of the fibres was observed up to an extent of 50% conversion of acetate to hydroxyl groups. Further change in the tensile strength and the elongation at break was attributed partly to the grafted poly(vinyl acetate)/poly(vinyl alcohol) balance and partly to the loss due to degradation of the fibres.     

Processing and properties of an ethylene–vinyl acetate blend foam incorporating ethylene–vinyl acetate and polyurethane waste foams

Waste polyurethane foam (w‐PU) and waste ethylene–vinyl acetate foam (w‐EVA) were used as fillers for the production of an ethylene–vinyl acetate (EVA) blend foam. Two different foaming techniques (single‐stage and heat–chill processes) were used for this purpose. The waste foam concentration was varied up to 30 wt % of the original EVA. The physical, mechanical, and morphological properties of the filled foam were studied. The single‐stage process produced blend foams with a lower density and a greater cell size than the foams obtained by the heat–chill process. The density and compression strength of the blend foam increased as the percentage of w‐PU foam increased. However, for the w‐EVA/EVA blend foams, the addition of w‐EVA foam did not significantly affect the density or compression strength compared to the original EVA foams. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44708.     

Use of pyrolysed oil shale as filler in poly(ethylene‐co‐vinyl alcohol)

The pyrolysed oil shale (POS) obtained from the pyrolysis of bituminous rock was used as filler in poly(ethylene‐co‐vinyl alcohol) (EVAL). The effects of vinyl alcohol content in the EVAL and the particle size of pyrolysed oil shale in the mechanical properties were investigated. The EVAL was prepared by hydrolysis of poly(ethylene‐co‐vinyl acetate) (EVA) with 8 and 18 wt % of vinyl alcohol content. The composites were prepared in a rotor mixer at 180°C with concentration of pyrolysed oil shale up to 5 wt %. Stress–strain plots of compression‐molded composites showed a synergic behavior in the mechanical properties for low concentrations (1–5 wt %) of POS in all particle sizes and EVAL used. Such behavior indicates a close packing and strong interactions between the inorganic filler and the polymer. Increasing of the vinyl alcohol content of EVAL improved the compatibility between the polymer and filler, but decreasing the POS particle size had no effect on the properties. The modulus and the ultimate tensile strength also increased in all concentrations of POS for both EVAL. Mechanical properties and dynamic mechanical analysis also demonstrated the compatibility between EVAL and POS. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 1658–1665, 2004     

Melt grafting of poly(ethylene‐vinyl acetate) copolymer with maleic anhydride

Poly(ethylene‐vinyl acetate) (EVA) copolymer was melt grafted with maleic anhydride (MAH) in a twin screw extruder in the presence of peroxide. It is confirmed that MAH has been melt grafted on the backbone of EVA by FTIR using the method of hydrolysis. The NMR analysis suggests that the grafting reaction occurs on the tertiary carbon of main chain of EVA other than the methyl moiety of vinyl acetate (VA) group. The incorporation of VA groups onto the matrix shows a competitive effect on the grafting. The existence of VA groups promotes the extent of MAH graft onto EVA; nevertheless, it also weakens the crystallizability of main chain. When the content of peroxide initiator is 0.1 wt % based on the polymer matrix, the grafting degree increases with increasing the concentration of monomer. When the peroxide content is higher than 0.1 wt %, side reactions such as crosslinking or disproportionation will be introduced into this system. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 841–846, 2006     

Preparation and properties of microcapsule with EVA core‐PU shell structure

Microcapsule with poly(ethylene‐co‐vinylacetate) (EVA) core‐polyurethane (PU) shell structure was synthesized by interfacial polymerization in aqueous polyol dispersion with ethylene diamine as the chain extender of toluene diisocyanate in poly(vinyl alcohol) aqueous solution as the stabilizing agent. The effects of polyol constituent on the average particle size and distributions, morphologies, color strength, and friction fastness of core‐shell particles were investigated to design microcapsule. The friction fastness of printed fabrics with EVA core‐PU shell microcapsules became the increase to 4–5 grades. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 893–902, 2007     

Kinetic features of the nonisothermal oxidative degradation of ethylene vinyl acetate copolymers

Thermogravimetric analysis was used for a comparative investigation of the thermooxidative decomposition of ethylene vinyl acetate (EVA) copolymers with different vinyl acetate (VA) group contents. There were two stages of mass loss in this process. It was revealed that the apparent activation energies were correlated with the content of VA groups in the EVA copolymers. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 1958–1961, 2004     

Improvement of compression set property of ethylene vinyl acetate copolymer/ethylene‐1‐butene copolymer/organoclay nanocomposite foams

To chemically bond polymer and organoclay, low molecular weight trimethoxysilyl‐modified polybutadiene (Silane) was used in this study. When Silane was added, ethylene‐vinyl acetate copolymer (EVA)/ethylene‐1‐butene copolymer (EtBC)/methyl tallow bis‐2‐hydroxyethyl quaternary ammonium‐modified montmorillonite (OH‐MMT)/Silane foams with and without maleic anhydride grafted EtBC (EtBC‐g‐MAH) display lower compression set than EVA/EtBC foams. According to the compression set result, OH‐MMT is more effective in improvement of compression set than dimethyl dihydrogenated tallow quaternary ammonium‐modified montmorillonite (DM‐MMT) because in addition of OH groups in the organoclay surface, the OH groups of the alkylammonium ion existed in interlayer of OH‐MMT may react with silanol group of Silane. The possible chemical reactions between Silanol groups of Silane and the hydroxyl groups of OH‐MMT and DM‐MMT were proved by ATR‐FTIR experiments. POLYM. ENG. SCI., 2008. © 2008 Society of Plastics Engineers.     

Toward green three‐phase composites with enhanced dielectric permittivity

This work aims to investigate the dielectric potential of microcrystalline cellulose, a green biosourced material, as a third constituent in the three‐phase composites based on ethylene vinyl acetate‐vinyl ester of versatic acid (EVA‐VeoVa) terpolymer and BaTiO₃. For that, new green three‐phase composites were prepared using an economic and green process, with simple implementation at room temperature and using water as a solvent. Compared with the binary composite EVA‐VeoVa/BaTiO₃, the three‐phase composite EVA‐VeoVa/BaTiO₃/microcrystalline cellulose showed an improvement of the BaTiO₃ particles dispersion, enhanced relative permittivity, and reduced dielectric loss, which explains the significance of this study. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46147.     

Polyaniline/ethylene vinyl acetate composites as dielectric sensor

The compressive stress (pressure) sensitivity of dielectric properties has been studied on ethylene vinyl acetate (EVA)/polyaniline (Pani) composites prepared through In‐situ synthesis of polyaniline in the solution of insulating EVA matrix. It is observed that the dielectric constant and loss increase with the increase in applied pressure, that is some piezoelectric effect is observed for these composites. The dielectric properties are also found to increase with respect to time when subjected under constant pressure. It is seen that changes in dielectric constant and loss follow some exponential relationships with respect to applied pressure and time duration under constant stress, and the relaxation time for the composites can be calculated. The relaxation time decreases with the increase in concentration of Pani in a composite. However, a composite with lower Pani content exhibits relatively higher change in dielectric properties against applied pressure and time duration under compression compared to one with higher loading. Granular crew type morphology of Pani is observed through scanning electron microscopic (SEM) study. This study reveals that these EVA‐Pani composites can be used as dielectric sensor. POLYM. ENG. SCI., 54:1632–1639, 2014. © 2013 Society of Plastics Engineers     

Production of polymeric membranes made of polypropylene,poly(ethylene‐co‐vinyl acetate), and poly(vinyl alcohol)

In this study, we prepared and characterized membranes containing polypropylene, poly(ethylene‐co‐vinyl acetate) (EVA), and poly(vinyl alcohol) (PVA). The production process involved blend extrusion and calendering followed by solvent extraction by toluene and water of the EVA and PVA phases. Morphology studies involving scanning electron microscopy determined the pore size distribution at the surface and in the internal regions of the membrane. The resulting membrane properties were related to the processing variables (extension rate, process temperature, and solvent extraction methods) and blend composition. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 3275–3286, 2004     

Poly(lactic acid)/ethylene vinyl acetate copolymer blend composites with wood flour and wollastonite: Physical properties,morphology, and biodegradability

In the present study, poly(lactic acid) (PLA), a biodegradable plastic, was melt‐blended with five weight percentages (10–50 wt%) of ethylene vinyl acetate (EVA) copolymer, a non‐biodegradable plastic, having a vinyl acetate content of 19 wt% and a melt flow index of 530 g/10 min, on a twin screw extruder, followed by an injection molding. The blends at 10 and 20 wt% EVA revealed a noticeably increased impact strength and strain at break over the pure PLA, and the blend at 10 wt% EVA exhibited the highest impact strength and strain at break. The 90/10 (wt%/wt%) PLA/EVA blend was then selected for preparing either single or hybrid composite with wood flour (WF) and wollastonite (WT). The filler loading was fixed at 30 parts by weight per hundred of resin throughout the experiment, and the WF/WT weight ratios were 30/0, 20/10, 15/15, 10/20, and 0/30. The prepared composites were examined for their mechanical and thermal properties, melt flow index, flammability, water uptake, and biodegradability as a function of composition. All the composites showed a filler‐dose‐dependent decrease in the impact strength and strain at break, but an increase in the tensile and flexural modulus (optimal at 0/30 WF/WT) and tensile and flexural strength (optimal at 30/0 WF/WT) as compared with the neat 90/10 (wt%/wt%) PLA/EVA blend. In addition, the melt flow index, char residue, anti‐dripping ability, water uptake, and biodegradability of the composites were also higher than those of the neat blend. J. VINYL ADDIT. TECHNOL., 25:313–327, 2019. © 2019 Society of Plastics Engineers