Active aeroelastic flutter analysis and vibration control of supersonic composite laminated plate

The active aeroelastic flutter analysis and vibration control at the flutter bounds of the supersonic composite laminated plates with the piezoelectric patches are studied. The piezoelectric patches are bonded on the top and bottom surfaces of the composite laminated plate to act as the sensor and actuator so that the active aeroelastic flutter suppression and vibration control for the supersonic laminated plate can be conducted. The unsteady aerodynamic pressure in supersonic flow is computed by using the supersonic piston theory. Hamilton’s principle with the assumed mode method is used to develop the governing equation of the structural system. The controller is designed by the velocity feedback and proportional feedback control algorithm, and the active damping and stiffness are obtained. The solutions for the complex eigenvalue problem are obtained by using the generalized eigenvalue methodology. The natural frequencies and damping ratios are also gotten. The aeroelastic flutter bounds of the supersonic composite laminated plate are calculated to investigate the characteristics of the aeroelastic flutter. The impulse responses of the structural system are calculated by using the Houbolt numerical algorithm to study the active aeroelastic vibration control. The influences of ply angle of the laminated plate and the control method on the characteristic of flutter and active vibration control are analyzed. From the numerical results it is observed that the aeroelastic flutter characteristics of the supersonic composite laminated plate can be improved and that the aeroelastic vibration response amplitudes can be reduced, especially at the flutter points, by the proportional feedback or the velocity feedback control algorithm using the piezoelectric actuator/sensor pairs. The effectiveness of the flutter control by the two control algorithms is also compared. The results of this study are of great significance to the flutter analysis and aeroelastic design of the aircraft.     

Optimal placement of piezoelectric actuators on plate structures for active vibration control via modified control matrix and singular value decomposition approach using modified heuristic genetic algorithm

The present work deals with the optimal placement of piezoelectric actuators on a thin plate using modified control matrix and singular value decomposition (MCSVD) approach. The MCSVD is considered as the fitness function and optimal positions of the actuators are obtained by maximizing it with MHGA (modified heuristic genetic algorithm). Vibration suppression has been studied for simply supported plate with piezoelectric patches in optimal positions to suppress first specified modes using LQR (linear quadratic regulator) controller. It is observed that the positions of patches obtained with this approach give greater vibration suppression, reduced computational requirements, and provide global optimum solution only.     

基于模态应变能分布的压电致动器/传感器位置优化遗传算法

本文由线弹性压电结构有限元动力方程,推导了压电智能结构的振动控制方程。建立了准确模拟层合压电结构动力行为的有限元模型。基于主结构模态应变能分布提出了一种新的优化目标函数,将压电致动器/传感器位置编号作为优化变量,建立了离散变量表示的智能结构优化问题,并通过二进制编码的遗传算法（GA）求解了该最优问题。以四边固支复合层合压电智能板为数值算例,采用比例反馈控制, 研究了最优位置配置致动器/传感器智能结构目标模态的控制效果。数值结果表明基于模态应变能分布的遗传算法所得优化解具有较好的振动控制效果。     

Analysis of active damping in composite laminate cylindrical shells of revolution with skewed PVDF sensors/actuators

Active damping in a FRP composite cylindrical shell with collocated piezoelectric sensors/actuators is studied. The electrode on the sensors/actuators are spatially shaped to reduce spillover between circumferential modes. A three noded, isoparametric, semianalytical finite element is developed and used to model the cylindrical shell. The element is based on a mixed piezoelectric shell theory which makes a single layer assumption for the displacements and a layerwise assumption for the electric potential. The effects of location of patch of collocated piezoelectric sensors/actuators, percentage length of the shell covered with these patches, fiber angle of the laminae in the composite laminate, stacking sequence of laminae in a laminate and skew angle of the sensor/actuator piezoelectric material, on the system damping for various modes is studied.     

Optimal shapes of PZT actuators for laminated structures subjected to displacement or eigenfrequency constraints

In this paper, dynamics, electromechanical couplings, and control of piezoelectric laminated cylindrical shells and rectangular plates are investigated. It is assumed that the piezoelectric layers are distributed on the top and bottom surfaces of the structures. First of all the governing equations and boundary conditions including elastic and piezoelectric couplings are formulated and solutions are derived. Then control of the plate/shells deflections and natural frequencies using high control voltages are studied in order to optimize the structural response. The present formulation of optimal design introduces boundaries of piezoelectric patches as new class of design variables. In addition, classical design variables in the form of ply orientation angles of orthotropic layers are also taken into account. For the actuator/actuator configuration, it was shown that the piezoelectric actuators can significantly reduce deformations/eigenfrequencies of the composite plate. Those effects were dependent on the value of the applied voltage. It was demonstrated that the proper choice of the actuator area is more efficient in reducing deflections/eigenfrequencies. The accuracy of optimal design are verified both with the aid of the FE package ABAQUS and using the standard Rayleigh-Ritz method. The results concerning active vibration control for axisymmetric cylindrical shells are also discussed.     

Optimal design in vibration control of adaptive structures using a simulated annealing algorithm

Advanced reinforced composite structures incorporating piezoelectric sensors and actuators are increasingly becoming important due to the development of smart structures. These structures offer potential benefits in a wide range of engineering applications such as vibration and noise suppression, shape control and precision positioning. This paper presents a finite element formulation based on the classical laminated plate theory for laminated structures with integrated piezoelectric layers or patches, acting as sensors and actuators. The finite element model is a single layer triangular nonconforming plate/shell element with 18 degrees of freedom for the generalized displacements, and one additional electrical potential degree of freedom for each surface bonded piezoelectric element layer or patch. The control is initialized through a previous optimization of the core of the laminated structure, in order to minimize the vibration amplitude and maximize the first natural frequency. Also the optimization of the patches position is performed to maximize the piezoelectric actuators efficiency. The simulated annealing algorithm is used for these purposes. To achieve a mechanism of active control of the structure dynamic response, a feedback control algorithm is used, coupling the sensor and active piezoelectric layers or patches, and to calculate the dynamic response of the laminated structures the Newmark method is considered. The model is applied in the optimization of an illustrative adaptive laminated plate case. The influence of the position and number of piezoelectric patches, as well as the control gain, are investigated and the results are presented and discussed.     

Optimal shape control of functionally graded smart plates using genetic algorithms

This paper deals with optimal shape control of functionally graded smart plate containing patches of piezoelectric sensors and actuators. The genetic algorithm (GA) is designed to search for optimal actuator voltage and displacement control gains for the shape control of the functionally graded material (FGM) plates. The work extends the earlier finite element formulations of the two leading authors, so that it can be readily treated using genetic algorithms. Numerical results have been obtained to study the effect of the shape control of the FGM plates under a temperature gradient by optimising (i) the voltage distribution for the open loop control, and (ii) the displacement control gain values for the closed loop feedback control. The effect of the constituent volume fractions of zirconia, through varying the volume fraction exponent n, on the optimal voltages and gain values has also been examined.     

压电耦合板主动控制及稳定性分析

本文研究压电耦合板的主动控制及稳定性。压电耦合板在采用作为传感器和驱动器的压电片之间的速度负反馈时 ,能增大系统的阻尼性能。本文以闭环控制系统方法的特征值分析为基础 ,分析研究了其稳定性。研究表明主动控制在增加系统阻尼性能的同时 ,亦可能导致系统出现不稳定现象。文中指出当仅有对点之间的负反馈时 ,系统是渐近稳定的 ;当负反馈增益矩阵呈非对称或对称但非正定时 ,系统可能出现非稳定。文中以算例进一步给予证实。     

Genetic algorithm based optimal design for vibration control of composite shell structures using piezoelectric sensors and actuators

The present article deals with the design of optimal vibration control of smart fiber reinforced polymer (FRP) composite shell structures using genetic algorithm (GA) based linear quadratic regulator (LQR) and layered shell coupled electro-mechanical finite element analysis. Open loop procedure has been used for optimal placement of actuators considering the control spillover of the higher modes to prevent closed loop instability. An improved real coded GA based LQR control scheme has been developed for designing an optimal controller in order to maximize the closed loop damping ratio while keeping actuators voltages within limit. Results show that increased closed loop-damping has been achieved with a large reduction of control effort considering control spillover.     

层合板中压电作动器最优厚度和嵌入位置研究

研究了压电结构中压电片厚度和嵌入深度的优化问题。首先给出了压电层合板的高阶耦合分析模型;然后以不受约束的含压电铺层复合材料板为代表,在压电层厚度方向施加电场时板自由变形,假设板任意微元横截面上内力为零,以其弯(扭)曲曲率最大为优化目标,建立了求解压电片最优厚度和嵌入深度问题的约束优化模型。最后分别以各向同性板中嵌入各项同性压电片和复合材料板中嵌入各向异性压电片为例进行了分析,绘出了目标函数的三维曲面图及等高线图,结果表明压电片的作动效能与其厚度和嵌入位置密切相关,而最优厚度和嵌入位置是由压电片和基体的材料特性决定的。     

Active damping of rotating composite thin-walled beams using MFC actuators and PVDF sensors

The object of this research is to enhance the damping performance for vibration suppression of rotating composite thin-walled beams using MFC actuators and PVDF sensors. The formulation is based on single cell composite beam including a warping function, centrifugal force, Coriolis acceleration and piezoelectric effect. Adaptive capability of the beam is acquired through the use of a negative velocity feedback control algorithm. Numerical analysis is performed using finite element method and Newmark time integration method is used to calculate the time response of the model. It is observed that the feedback control gain has an effect on damping performance. The paper continues with an investigation into influences of parameters such as the rotating speed and the fiber orientation in host structures. Also, it is confirmed that effective damping performance is achievable through the suitable arrangement and distributed size of sensor and actuator pair using case study.     

Hybrid damping of smart, functionally graded plates using piezoelectric, fiber-reinforced composites

This paper deals with the investigation of active, constrained layer damping (ACLD) of smart, functionally graded (FG) plates. The constraining layer of the ACLD treatment is considered to be made of a piezoelectric, fiber-reinforced composite (PFRC) material with enhanced effective piezoelectric coefficient that quantifies the in-plane actuating force due to the electric field applied across the thickness of the layer. The Young's modulus and the mass density of the FG plates are assumed to vary exponentially along the thickness of the plate, and the Poisson's ratio is assumed to be constant over the domain of the plate. A finite-element model has been developed to model the open-loop and closed-loop dynamics of the FG plates integrated with two patches of ACLD treatment. The frequency response of the plates revealed that the active patches of ACLD treatment significantly improve the damping characteristics of the FG plates over the passive damping. Emphasis has been placed on investigating the effect of variation of piezoelectric fiber angle in the constraining layer of the ACLD treatment on the attenuating capability of the patches. The analysis also revealed that the activated patches of the ACLD treatment are more effective in controlling the vibrations of FG plates when the patches are attached to the surface of the FG plates with minimum stiffness than when they are attached to the surface of the same with maximum stiffness.     

基于不同压电材料作动机制的压电层厚度研究

研究了压电材料复合板的3种作动机制,弯曲作动机制、剪切作动机制、混合作动机制,针对粘贴在纤维板上不同厚度的压电作动层,具体分析了复合板的端部位移,研究结果对噪声和振动的主动控制中的模态控制和智能结构静态形状控制提供了一定的参考。     

Active constrained layer damping of geometrically nonlinear vibrations of smart laminated composite sandwich plates using 1–3 piezoelectric composites

This paper deals with the analysis of active constrained layer damping (ACLD) of geometrically nonlinear vibrations of sandwich plate with orthotropic laminated composite faces separated by a flexible core. The constraining layer of the ACLD treatment is composed of the vertically/obliquely reinforced 1?C3 piezoelectric composites. The Golla?CHughes?CMcTavish method has been implemented to model the constrained viscoelastic layer of the ACLD treatment in time domain. The first-order shear deformation theory and the Von Kármán type nonlinear strain displacement relations are used for analyzing this coupled electro-elastic problem. A three dimensional finite element model of smart laminated composite sandwich plate integrated with ACLD patches has been developed to investigate the performance of these patches for controlling the geometrically nonlinear vibrations of the plates. The numerical results indicate that the ACLD patches significantly improve the damping characteristics of the sandwich plates with laminated cross-ply and angle-ply facings for suppressing their geometrically nonlinear vibrations. Particular emphasis has been placed on investigating the effect of the variation of piezoelectric fiber orientation angle on the performance of the ACLD treatment.     

《压电层合板的振动主动控制》

利用一阶剪切变形理论推导压电层合板的抗弯刚度,由Hamilton变分原理建立压电层合板的有限元模型,采用模态叠加方法对有限元模型降阶。在应变最大处配置制动器和传感器,并采用二次线性控制的独立模态空间控制法来进行板结构的主动控制。数值算例验证了这种力学建模方法和控制方法的有效性。     

Performance of piezoelectric fiber-reinforced composites for active structural-acoustic control of laminated composite plates

This paper deals with the active structural acoustic control of thin laminated composite plates using piezoelectric fiber-reinforced composite (PFRC) material for the constraining layer of active constrained layer damping (ACLD) treatment. A finite element model is developed for the laminated composite plates integrated with the patches of ACLD treatment to describe the coupled structural-acoustic behavior of the plates enclosing an acoustic cavity. The performance of the PFRC layers of the patches has been investigated for active control of sound radiated from thin symmetric and antisymmetric cross-ply and antisymmetric angle-ply laminated composite plates into the acoustic cavity. The significant effect of variation of piezoelectric fiber orientation in the PFRC layer on controlling the structure-borne sound radiated from thin laminated plates has been investigated to determine the fiber angle in the PFRC layer for which the structural-acoustic control authority of the patches becomes maximum.     

A sensor charge output deviation method for delamination detection using isolated piezoelectric actuator and sensor patches

Delamination is one of the most prevalent failure mechanisms for laminated composites. To secure the safety of composite structures, it is required and necessary to develop cost-effective and efficient delamination detection techniques and methods. In this paper, a dynamic analytical model, namely sensor charge output deviation method is proposed to identify a delamination embedded in a cantilever laminated composite beam bonded with isolated piezoelectric actuator and sensor patches. Two pairs of collocated piezoelectric patches are bonded on top and bottom surfaces of the beam and used as actuators for exciting the composite beam. Another piezoelectric patch with gridding electrode pattern on its top surface is bonded on the top surface of the host beam and is employed as a sensor to record the required voltage and thus the sensor charge output along the beam. The effects of some major geometric parameters and the type of applied electric voltage on the sensor charge output distribution and delamination detection sensitivity are discussed in this paper. A comparison between the analytical models using isolated piezoelectric actuator and sensor patches and that using integrated piezoelectric sensor/actuator layer, which was developed previously, is conducted. For the baseline case considered here, there is an excellent agreement of the first three order frequencies between the present finite element analysis and analytical models.     

Analysis of laminated composite beams and plates with piezoelectric patches using the element-free Galerkin method

 An efficient meshfree formulation based on the first-order shear deformation theory (FSDT) is presented for the static analysis of laminated composite beams and plates with integrated piezoelectric layers. This meshfree model is constructed based on the element-free Galerkin (EFG) method. The formulation is derived from the variational principle and the piezoelectric stiffness is taken into account in the model. In numerical test problems, bending control of piezoelectric bimorph beams was shown to have the efficiency and accuracy of the present EFG formulation for this class of problems. It is demonstrated that the different boundary conditions and applied actuate voltages affects the shape control of piezolaminated composite beams. The meshfree model is further extended to study the shape control of piezo-laminated composite plates. From the investigation, it is found that actuator patches bonded on high strain regions are significant in deflection control of laminated composite plates. Received: 23 October 2001 / Accepted: 29 July 2002     

Control of geometrically nonlinear vibrations of skew laminated composite plates using skew or rectangular 1–3 piezoelectric patches

This paper deals with the analysis of active constrained layer damping (ACLD) of geometrically nonlinear transient vibrations of skew laminated composite plates using skew or rectangular patches of the ACLD treatment. The constraining layer of the patch of the ACLD treatment is composed of the vertically/obliquely reinforced 1–3 piezoelectric composite material. The Golla–Hughes–McTavish method has been used to model the constrained viscoelastic layer of the ACLD treatment in the time domain. A coupled electromechanical nonlinear three dimensional finite element model of skew laminated thin composite plates integrated with the skew or rectangular patches of ACLD treatment has been derived. The performance of the patches is investigated for different configurations of their placements on the top surface of the skew substrate plates. The analysis reveals that the ACLD treatment significantly improves the active damping characteristics of the skew laminated composite plates over the passive damping for suppressing their geometrically nonlinear transient vibrations. It is found that even though the substrate laminated plates are skew, a rectangular patch of the ACLD treatment located at the centre of the top surface of the substrate should be used for optimum damping of geometrically nonlinear vibrations of skew laminated composite plates irrespective of their skew angles and boundary conditions. The effects of piezoelectric fiber orientation angle and the skew angles of the substrate plates on the control authority of the ACLD patches have been emphatically investigated.     

Active structural-acoustic control of laminated composite plates using vertically/obliquely reinforced 1–3 piezoelectric composite patch

This article deals with the active structural-acoustic control of thin laminated composite plates using vertically reinforced 1–3 piezoelectric fiber-reinforced composite (PFRC) material for constraining layer of active constrained layer damping (ACLD) treatment. A finite element model is developed for the laminated composite plates integrated with ACLD patches and coupled with acoustic cavity to describe the coupled structural-acoustic behavior of the plates enclosing the cavity. Both in-plane and out of plane actuation of the constraining layer of the ACLD treatment have been utilized for deriving the finite element model. The analysis revealed that the vertical actuation dominates over the in-plane actuation. The performance of PFRC layers of the patches has been investigated for active control of sound radiated from thin symmetric and antisymmetric cross-ply and antisymmetric angle-ply laminated composite plates into the acoustic cavity.