Off‐line monitoring of butyl acrylate and vinyl acetate homopolymerization and copolymerization in toluene

A study of butyl acrylate (BA) and vinyl acetate (VAc) solution homopolymerization and copolymerization in toluene was carried out. The conversion and copolymer composition were monitored using traditional techniques (gravimetry and ¹H‐NMR spectroscopy) and attenuated total reflectance‐Fourier transform IR (ATR‐FTIR) spectroscopy with a diamond‐composite probe and light conduit technology. The peak height of the characteristic absorbances of the monomer(s) during the course of the reaction was used to calculate the conversion and copolymer composition for the ATR‐FTIR monitoring. The data obtained using a ReactIR? 1000 reaction analysis system in the off‐line mode showed very good agreement with data obtained using traditional techniques. The solvent effects on BA and VAc solution homopolymerizations and copolymerizations in toluene were also investigated. Improvement to model predictions was obtained by allowing the lumped constant (k_p/k) to vary with the solvent concentration. Experimental data and model predictions of the number‐ and weight‐average molecular weights for the investigated systems are also presented. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 82: 2958–2977, 2001     

Poly(vinyl pyrrolidone‐co‐vinyl acetate)‐graft‐poly(ε‐caprolactone) as a compatibilizer for cellulose acetate/poly(ε‐caprolactone) blends

Poly(vinyl pyrrolidone‐co‐vinyl acetate)‐graft‐poly(ε‐caprolactone) (PVPVAc‐g‐PCL) was synthesized by radical copolymerization of N‐vinyl‐2‐pyrrolidone (VP)/vinyl acetate (VAc) comonomer and PCL macromonomer containing a reactive 2‐hydroxyethyl methacrylate terminal. The graft copolymer was designed in order to improve the interfacial adhesiveness of an immiscible blend system composed of cellulose acetate/poly(ε‐caprolactone) (CA/PCL). Adequate selections of preparation conditions led to successful acquisition of a series of graft copolymer samples with different values of molecular weight ( ), number of grafts (n), and segmental molecular weight of PVPVAc between adjacent grafts (M_n (between grafts)). Differential scanning calorimetry measurements gave a still immiscible indication for all of the ternary blends of CA/PCL/PVPVAc‐g‐PCL (72 : 18 : 10 in weight) that were prepared by using any of the copolymer samples as a compatibilizer. However, the incorporation enabled the CA/PCL (4 : 1) blend to be easily melt‐molded to give a visually homogeneous film sheet. This compatibilizing effect was found to be drastically enhanced when PVPVAc‐g‐PCLs of higher and M_n (between grafts) and lower n were employed. Scanning electron microscopy revealed that a uniform dispersion of the respective ingredients in the ternary blends was attainable with an assurance of the mixing scale of several hundreds of nanometers. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Preparation of toughened polypropylene‐g‐poly(butyl acrylate‐co‐acrylated castor oil) by suspension grafting polymerization

Butyl acrylate (BA) with acrylated castor oil (ACO) was grafted onto porous polypropylene (PP) granules by grafting polymerization. Crosslinked copolymer microdomains which functioned as rubber phase to improve the toughness of PP were filled into the pores of PP granules. The sizes of crosslinked copolymer microdomains were controlled in the range of 0.1–1 μm in PP matrix. The results of fourier transform infrared spectroscopy and scanning electron microscope of PP‐g‐(BA‐co‐ACO) after extracted by acetone confirmed that BA and ACO were grafted onto PP successfully. The effects of comonomer ratio, initiator content and comonomer content on grafting percentage (GP) and grafting efficiency (GE) were investigated. The GP of PP‐g‐(BA‐co‐ACO) could be up to 21.3% with the comonomer content increasing to 25%. The crosslinked copolymer decreased the melting flow index and the relative crystallinity of PP. Dynamic mechanical thermal analysis showed that the glass transition temperature of PP decreased slightly from 22°C to 15°C. The addition of 5% comonomer content led to an increase of notched impact strength from 1.96 to 3.81 kJ/m² (nearly doubled) and a marginal decrease in the tensile strength of PP. Then with further addition of comonomer, the notched impact strength increased to 8.98 kJ/m² while the tensile strength was 29.37 MPa. POLYM. ENG. SCI., 58:86–93, 2018. © 2017 Society of Plastics Engineers     

Empirical Modeling of Butyl Acrylate/Vinyl Acetate/Acrylic Acid Emulsion‐Based Pressure‐Sensitive Adhesives

Summary: Butyl acrylate/vinyl acetate/acrylic acid (BA/VAc/AA) emulsion latexes were produced in a semi‐batch mode. The objective was to generate polymers with properties favoring their application as pressure‐sensitive adhesives. The influence of the individual monomer concentrations on final properties such as glass transition temperature (T_g), peel strength, shear strength and tack was investigated. To obtain the maximum amount of information in a reasonable number of runs, a constrained three‐component mixture design was used to define the experimental conditions. Latexes were coated onto a polyethylene terephthalate carrier and dried. Different empirical models (e.g. linear, quadratic and cubic mixture models) governing the individual properties (i.e. T_g, peel adhesion, shear resistance and tack) were developed and evaluated. In the given experimental region, no single model was found to fit all of the responses (i.e. the final properties). However, in all models the most significant factor affecting the final properties was the AA concentration, followed by the VAc concentration.

Shear strength contour lines over the investigated region.     

Carbon‐13 nuclear magnetic resonance investigation of styrene–α‐methylstyrene copolymers

A copolymer based on α‐methylstyrene (AMS) was investigated by nuclear magnetic resonance (NMR). The styrene‐co‐α‐methylstyrene (SAMS) was analyzed by solution and solid‐state NMR techniques. Three copolymers of SAMS with different compositions presented a particular behavior. The solution results showed the copolymer microstructure and the AMS content. The carbon‐13 spectra of SAMS C indicated that the AMS CH₃ signal was detected at three distinct chemical shifts, because of the different comonomer‐sequences distribution. The proton spin–lattice relaxation time in the rotating frame (Tρ) parameter was chosen because it permits the evaluation of changes in the molecular mobility. The values of Tρ found for the copolymers confirmed the random distribution in the samples. The copolymer with a low quantity of AMS (1.7%), when analyzed by this relaxation parameter, showed lower values that were interpreted as an antiplasticization effect. The SAMS copolymer with a higher AMS quantity showed a plasticization effect. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 261–266, 2001     

Chemorheology and thermomechanical characteristics of benzoxazine‐urethane copolymers

In this research, processability and some important thermomechanical properties of polybenzoxazine (BA‐a) modified with a highly flexible urethane elastomer (PU) are discussed. This copolymer has been reported to show synergy in its glass transition temperature and some mechanical properties thus provides a fascinating group of high temperature polymers with enhanced flexibility. The results reveal that a processing window of the BA‐a/PU mixtures is widened with the increasing urethane prepolymer fraction, that is, the liquefying temperature is lowered and the gel point shifted to higher temperature with the amount of the PU. Synergism in glass transition temperature (T_g) of this copolymer was clearly confirmed, i.e., T_g's of the BA‐a/PU alloys were significantly greater than those of the parent resins, i.e., BA‐a (T_g = 166°C) and PU (T_g = ? 70°C). In addition, flexural modulus was found to systemically decrease from 5.4 GPa of the neat polybenzoxazine to 2.1 GPa at 40% by weight of the PU. Flexural strength of the alloys also shows a synergistic behavior at the BA‐a/PU ratio of 90/10. Coefficient of thermal expansion of the polymer alloys were also found to show a minimum value at BA‐a/PU = 90/10. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Mechanical and dynamic mechanical studies of epoxy/VAc‐EHA/HMMM IPN–jute composite systems

Epoxy [50:50 mixture of Di‐Glycidyl Ether of Bis‐Phenol A (DGEBA) and Epoxidized Novolac (EPN)] was solution blended with Vinyl Acetate‐2‐ Ethylhexylacrylate (VAc‐EHA) resin in aqueous medium, in varying weight fractions, with Hexamethoxymethylmelamine (HMMM) as a crosslinker and data was compared with a control. The present work was aimed to optimize the tensile strength, dynamic mechanical strength, impact strength, and toughness by preparing a blend followed by jute composites of a semi‐ and full interpenetrating network (IPN). In control experiments epoxy alone was crosslinked (semi‐IPN), whereas the DGEBA‐EPN and VAc‐EHA/HMMM were crosslinked separately (full‐IPN), using jute as the substrate for making composites. Composites of full‐IPN systems of epoxy/VAc‐EHA system had higher moduli and UTS than the semi‐IPN systems. Dynamic mechanical study showed that full‐IPN systems have higher T_g values than semi‐IPN systems. The impact strength increases with increasing proportions of VAc‐EHA copolymer. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 958–963, 2004     

Nucleation Effect of Layered Metal Phosphonate on Crystallization of Bacterial Poly[(3‐hydroxybutyrate)‐co‐(3‐hydroxyhexanoate)]

The nucleating effect of zinc phenylphosphonate (PPZn) was investigated on the as‐bacterially synthesized poly(3‐hydroxybutyrate) [P(3HB)] and poly[(3‐hydroxybutyrate)‐co‐(3‐hydroxyhexanoate)]s [P(3HB‐co‐3HHx)s] in order to improve their crystallization rate. PPZn is found an efficient nucleating agent on the crystallization of P(3HB) and P(3HB‐co‐3HHx) with low 3HHx unit content. The nucleation mechanism is proposed to be epitaxial nucleation. Both the comonomer‐unit composition and its distribution of P(3HB‐co‐3HHx)s were found exhibiting significant effect on the nucleating effect of PPZn. It is found that PPZn is more efficient on nucleating the crystallization of P(3HB‐co‐3HHx) with a broader comonomer‐unit compositional distribution than that with a narrower distribution.

     

Atom transfer radical homo‐ and copolymerization of styrene and methyl acrylate initiated with trichloromethyl‐ terminated poly(vinyl acetate) macroinitiator: A kinetic study

Atom transfer radical bulk copolymerization of styrene (St) and methyl acrylate (MA) initiated with trichloromethyl‐terminated poly(vinyl acetate) macroinitiator was performed in the presence of CuCl/PMDETA as a catalyst system at 90°C. Linear dependence of ln[M]₀/[M] versus time data along with narrow polydispersity of molecular weight distribution revealed that all the homo‐ and copolymerization reactions proceed according to the controlled/living characteristic. To obtain more reliable monomer reactivity ratios, the cumulative average copolymer composition at moderate to high conversion was determined by ¹H‐NMR spectroscopy. Reactivity ratios of St and MA were calculated by the extended Kelen‐Tudos (KT) and Mao‐Huglin (MH) methods to be r_St = 1.018 ± 0.060, r_MA = 0.177 ± 0.025 and r_St = 1.016 ± 0.053, r_MA = 0.179 ± 0.023, respectively, which are in a good agreement with those reported for the conventional free‐radical copolymerization of St and MA. Good agreement between the theoretical and experimental composition drifts in the comonomer mixture and copolymer as a function of the overall monomer conversion were observed, indicating that the reactivity ratios calculated by copolymer composition at the moderate to high conversion are accurate. Instantaneous copolymer composition curve and number‐average sequence length of comonomers in the copolymer indicated that the copolymerization system tends to produce a random copolymer. However, MA‐centered triad distribution results indicate that the spontaneous gradient copolymers can also be obtained when the mole fraction of MA in the initial comonomer mixture is high enough. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

A comprehensive study on the kinetics of aqueous free-radical homo- and copolymerization of acrylamide and diallyldimethylammonium chloride by online 1H-NMR spectroscopy

Free-radical homo- and copolymerization of acrylamide (AAm) and diallyldimethylammonium chloride (DADMAC) initiated with potassium persulfate (KPS) were performed in the presence of 0.1 M NaCl solution in D₂O at 50 °C. Online ¹H-NMR kinetic experiments were used to study polymerization kinetics via determination of the individual and overall conversion of the comonomers and compositions of the comonomer mixture and produced copolymer as a function of the reaction time. Reactivity ratios of the AAm and DADMAC were calculated by Mao-Huglin (MH) and extended Kelen-Tudos (KT) methods to be 7.0855?±?1.3963, 0.1216?±?0.0301 and 6.9458?±?2.0113, 0.1201?±?0.0437 respectively. “Lumped” kinetic parameter (k _p k _t ^??0.5 ) was estimated from experimental data. Results showed that k _p k _t ^??0.5 value increases by increasing mole fraction of the AAm in the initial reaction mixture. Drift in the comonomer mixture and copolymer compositions with reaction progress was evaluated experimentally and theoretically. Theoretical values were calculated from Meyer-Lowry equation by using reactivity ratios obtained from MH method. A good fitting between the experimental and theoretical values was observed, indicating accuracy of the reactivity ratios estimated in the present work. It was found from following changes in the copolymer composition with the comonomer conversion that produced copolymer has a statistical structure.     

Isothermal crystallization of metallocene‐based propylene/α‐olefin copolymers

Isothermal crystallization and subsequent melting behavior of two propylene/hexene‐1 copolymers and two propylene/octene‐1 copolymers prepared with metallocene catalyst were investigated. It is found that γ‐modification is predominant in all copolymers. The Avrami exponent shows a weak dependency on comonomer content and comonomer type. At higher crystallization temperatures (T_c) the crystallization rate constant changes more rapidly with T_c and the crystallization half‐time substantially increases. Double melting peaks were also observed at high T_c, which is attributed to the inhomogeneous distribution of comonomer units along the polymer chains and the existence of crystals with different lamellar thicknesses. The equilibrium melting temperatures (T) of the copolymers were obtained by Hoffman–Weeks extrapolation. It was found that the T decreases with increasing comonomer content, but are independent of comonomer type, implying that comonomer units are excluded from the crystal lattice. Dilation of the crystal lattice was also observed, which depends on crystallization, comonomer content, and comonomer type. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 240–247, 2005     

Kinetic study of radical polymerization. VII. Investigation into the solution copolymerization of acrylonitrile and itaconic acid by real‐time 1H NMR spectroscopy

Free radical solution copolymerization of acrylonitrile (AN) and itaconic acid (IA) was performed with DMSO‐d₆ as the solvent and 2,2′‐azobisisobutyronitrile (AIBN) as the initiator. Weight ratio of the monomers to solvent and molar ratio of initiator to monomers were constant in all experiments. The initial comonomer composition was the only variable in this study. On‐line ¹H NMR spectroscopy was applied to follow individual monomer conversion. Mole fraction of AN and IA in the reaction mixture (f) and in the copolymer chain (F) were measured with progress of the copolymerization reaction. Overall monomer conversion versus time and also compositions of monomer mixture and copolymer as a function of overall monomer conversion were calculated from the data of individual monomer conversion versus time. Total rate constant for the copolymerization reaction was calculated by using the overall monomer conversion versus time data and then k_p/k_t^0.5 was estimated. The dependency of k_p/k_t^0.5 on IA concentration was studied and it was found that this ratio decreases by increasing the mole fraction of IA in the initial feed. The variation of comonomer and copolymer compositions as a function of overall monomer conversion was calculated theoretically by the terminal model equations and compared with the experimental data. Instantaneous copolymer composition curve showed the formation of alternating copolymer chain during copolymerization reaction. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 3253–3260, 2007     

BA‐MMA‐POMA copolymer latexes prepared by using HMPS polymerizable emulsifier

BA‐MMA‐POMA copolymer latex was successfully prepared by soap‐free emulsion polymerization of 2‐(perfluoro‐(1,1‐bisisopropyl)‐2‐propenyl)oxyethyl methacrylate(POMA) with butyl acrylate(BA), methyl methacrylate (MMA) initiated by K₂S₂O₈ in the water. POMA was synthesized from the intermediate perfluoro nonene and 2‐hydroxyethyl methacrylate as the staring reactants. The structure of BA‐MMA‐POMA copolymer latex was investigated by Fourier transform infrared (FTIR). The characteristics of the film such as hydrophobicity and glass transition temperature were characterized with the contact angle and differential scanning calorimetry respectively. The influences of the amount of the fluorinated monomer and the initiator on the soap‐free emulsion polymerization and performance of the latex were studied. In addition, comparison with the latex prepared by the conventional emulsifier SDBS is investigated. Results show that the hydrophobicity and glass transition temperature (T_g) of the latex are increased when the fluorinated monomer is introduced to copolymerize with other monomers. The hydrophobicity can be improved further with heating. Compared with the latices prepared by using SDBS emulsifier, the latices prepared by using HMPS emulsifier have larger particle size, higher surface tension. However, the difference of their T_g is extremely minute. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Interpenetrating polymer networks based on poly(styrene‐co‐butylacrylate‐co‐hydroxyethyl methacrylate) and SiO2

Copolymer such as poly(styrene‐co‐butylacrylate‐co‐hydroxyethyl methacrylate) p (St‐BA‐HEMA) was prepared via free radical emulsion polymerization method. The resulting copolymer was converted to silicone secondary crosslinked interpenetrating polymer network (IPN) by condensation reaction with tetraethyl orthosilicate (TEOS). The obtained copolymers were characterized by using Fourier transform infrared spectroscopy (FTIR). Thermal properties of the copolymers were studied by using thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). Optical microscopy (OM) is used for studying the morphology, and then the effects of silicone concentrations, the reflux time, and composition on the phase morphology of P (St‐BA‐HEMA)‐SiO₂ IPNs were discussed. The broadening of the transition region was observed with the prolongation of the reflux time, and the tendency for aggregation of silicone on the surface was observed with Teflon as substrate plate. However, an optically transparent film was easily achieved at higher temperature due to the chemical crosslink and physical entanglement between the two phases of P (St‐BA‐HEMA)‐SiO₂. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Properties of PHMS‐g‐p [butylacrylate (BA)‐N‐hydroxyl‐methyl acrylamide (NMA)] graft copolymer emulsions

Emulsion graft copolymerization of poly(hydrogenmethylsiloxane) (PHMS) and butyl acrylate (BA) in the presence of functional comonomer N‐hydroxyl‐methyl acrylamide (NMA) was conducted by batch emulsion copolymerization to modify the properties of polysiloxane. Morphology of graft copolymer particles was characterized by transmission electron microscopy. The effect of polymerization method, PHMS content, initiator concentration, and NMA content on stability of emulsion, morphology, size of particle, and rheological properties were investigated. It has been found that stability of emulsion is better by semicontinuous emulsion polymerization than that of batch emulsion polymerization and it increased with increasing PHMS‐NMA concentration. Increasing PHMS concentration and NMA concentration, the particle size and the viscosities increase. The property of resistance to electrolytes of graft copolymer emulsions and swelling property of film were also discussed. Results showed PHMS‐g‐P [butylacrylate (BA)‐N‐hydroxyl‐methyl acrylamide (NMA)] graft copolymer emulsion has good resistance to electrolytes and the water absorption of its film increases with increasing BA‐NMA content grafted onto PHMS. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 71: 2209–2217, 1999     

Thermomechanical properties of arylamine‐based benzoxazine resins alloyed with epoxy resin

Effects of epoxy resin on various arylamine‐based benzoxazine resins, i.e., aniline (BA‐a), m‐toluidine (BA‐mt), and 3,5‐xylidine (BA‐35x), have been investigated. Processing windows of BA‐35x, BA‐mt, and BA‐a were found to be widened with the amount of the epoxy. Gel points of benzoxazine‐epoxy resin mixtures can be predicted by an Arrhenius equation, e.g., gel time of BA‐35x and epoxy mixture at 70:30 mass ratio can be estimated by t_gel = 0.7012 × 10^?7 exp (10.563/T). Glass transition temperature (T_g) of BA‐a and BA‐mt alloyed with epoxy exhibited a synergistic behavior with the maximum T_g value at the benzoxazine‐epoxy composition of 80:20 mass ratio. However, in the BA‐35x and epoxy mixture, the decreasing trend in T_g from 241°C to 223°C with an addition of epoxy was observed. Furthermore, flexural strength and strain‐at‐break of those alloys were found to increase with increasing amount of the epoxy while modulus increased with the polybenzoxazine mass fraction. POLYM. ENG. SCI., 2011. © 2011 Society of Plastics Engineers     

Hydrolytic Degradation of Amorphous Films of L‐Lactide Copolymers with Glycolide and D‐Lactide

Summary: Films of poly(L ‐lactic acid) (PLLA) and copolymers of L ‐lactide (LLA) with either glycolide [P(LLA‐GA)](81/19) or D ‐lactide [P(LLA‐DLA)](77/23) were prepared and an effect of comonomer type on the hydrolytic degradation of the films was studied in phosphate‐buffered solutions at 37 °C. The degraded films were investigated using gravimetry (weight loss and water absorption), gel permeation chromatography, DSC, X‐ray diffractometry, tensile testing and polarization optical microscopy. To exclude the effects of molecular weight and crystallinity on hydrolytic degradation, the films were prepared from polymers with similar molecular weights and were made amorphous by melt quenching. It was found that the hydrolytic degradation rate decreased in the order P(LLA‐GA) > P(LLA‐DLA) > PLLA. The hydrolytic degradation rate constant of PLLA and LLA copolymer films increased with increasing the water absorption (hydrophilicity), or with decreasing the initial glass transition temperature or the L ‐lactyl unit sequence length, indicating that the hydrolytic degradation rate of the copolymers was closely related to these three parameters. The crystallization of P(LLA‐GA) film occurred within hydrolytic degradation for 20 weeks.

M_n of PLLA and LLA copolymer films as a function of hydrolytic degradation time.     

A new general approach to determine more accurate comonomer reactivity ratios in controlled/living radical copolymerization systems

In controlled/living radical copolymerization (atom transfer radical copolymerization in this study) and in any other living chain‐growth copolymerization, the possible preferential addition of one of the comonomers onto the (macro)initiator‐derived (macro)radical can affect the copolymer composition, especially at low conversion; this results in inaccurate comonomer reactivity ratio estimation by the classic approach. A new general approach is introduced in this article, which allowed us to exclude the influence of the possible preferential addition of one of the comonomers onto the (macro)initiator‐derived (macro)radical on the copolymer composition at any conversion. According to this approach, copolymer chain grown during time t (t ≠ 0) is considered to be, in fact, the macroinitiator terminated with one of the comonomers under study, which will further grow during the time interval Δt′ = t′ ? t [where any reaction time t′ is considered to be grater than reaction time t, i.e. t′ > t] from a comonomer mixture with composition of f(t) [where f(t) is the molar ratio of comonomer i to comonomer j in the comonomer mixture] at time t. In such a situation, it is possible to obtain individual comonomer conversions [x_i(Δt′) and x_j(Δt′)], the overall comonomer conversion [x_ov(Δt′)], and the cumulative average copolymer composition for the copolymer formed during Δt′, from which more accurate comonomer reactivity ratios can be calculated by the various low‐ or high‐conversion methods, depending on the overall comonomer conversion. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Dynamic Mechanical Properties of Poly(propylene) Blends with Poly[ethylene‐co‐(methyl acrylate)]

Summary: Blends of poly(propylene) (PP) were prepared with poly[ethylene‐co‐(methyl acrylate)] (EMA) having 9.0 and 21.5% methyl acrylate comonomer. A similar series of blends were compatibilized by using maleic anhydride grafted PP. The morphology and mechanical properties of the blends were investigated using differential scanning calorimetry (DSC) and dynamic mechanical analysis (DMA) in tensile mode. The DMA method and conditions were optimized for polymer film specimens and are discussed in the experimental section. The DSC results showed separate melting that is indicative of phase‐separated blends, analogous to other PP‐polyethylene blends but with the added polarity of methyl acrylate pendant side groups that may be beneficial for chemical resistance. Heterogeneous nucleation of PP was decreased in the blends because of migration of nuclei into the more polar EMA phase. The crystallinity and peak‐melting temperature did not vary significantly, although the width of the melting endotherm increased in the blends indicating a change had occurred to the crystals. DMA analysis showed the crystal‐crystal slip transition and glass transition (T_g) for PP as well as a T_g of the EMA copolymer occurring chronologically toward lower temperatures. The storage modulus of PP and the blends was generally greater with annealing at 150 °C compared with isothermal crystallization at 130 °C. The storage modulus of the blends for isothermally crystallized PP increased with 5% EMA, then decreased for higher amounts of EMA. Annealing caused a decrease with increasing copolymer content. The extent of the trend was greater for the compatibilized blends. The T_g of the blends varied over a small range, although this change was less for the compatibilized blends.

Storage modulus for PP and EMA9.0 blends annealed at 150 °C.     

In Situ Preparation of a Compatibilized Poly(cis‐1,4‐butadiene)/Poly(ε‐caprolactone) Blend

The ternary Ziegler‐Natta‐type catalyst system based on neodymium versatate (NdV), diisobutylaluminium hydride (DIBAH) and ethylaluminium sesquichloride (EASC) was used for the in situ preparation of a compatibilized blend consisting of poly(cis‐1,4‐butadiene) (BR = butadiene rubber) and poly(ε‐caprolactone) (PCL). Poly(cis‐1,4‐butadiene)‐block‐poly(ε‐caprolactone) which acts as compatibilizer for the two immiscible polymers BR and PCL was obtained by a two step sequential polymerization with the preparation of a living cis‐1,4‐BR building block in the first stage and the subsequent polymerization of CL during the second stage. This preparation method resulted in a polymer blend comprising the homopolymers BR and PCL as well as the block copolymer BR‐block‐PCL. For detailed characterization the block copolymer was separated from the respective homopolymers BR and PCL by means of fractionation with the binary solvent mixture dimethylformamide/methylcyclohexane (DMF/MCH) which mixes well at elevated temperature and exhibits phase separation at ambient temperature. ¹H NMR, IR, SEC and TEM were used for characterization of the block copolymer.

TEM of BR‐block‐PCL.