Affinage electrolytique des ferronickels

Electrorefining of ferronickels is possible in a cell without diaphragm with the electrolyte CaCl₂ 5 M at 98°C.Behavior of the following impurities have been studied: Ag(I), Au(III), Bi(III), Cd(II), Co((II), Cu(I), Fe(II), Hg(II), Ni(II), Pb(II), Pd(II), Sb(III) and Sn(II).The electrochemical system Ni(II)/Ni(O)is much more reversible in this electrolyte and the only other electrochemical system which appears at the same potential is Cu(I)/Cu(O).Ferronickels of 23.2;72.2 and 94.4% in nickel have been refined in this medium without purification of the electrolyte. Nickel of a purity between 98.7 and 99.7% is obtained.In order to increase the nickel purity and for continuous operation of the method a purification of the electrolyte is necessary. Two methods are proposed: anion exchange resin and liquid—liquid extraction with tri-n-butyl phosphate (TBP).Partition coefficients and ion-exchanger capacities are given for following impurities: Fe(III), Fe(II), Co(II), Cu(II), Mn(II), Zn(II), Cr(III) and Pb(II).Percent extracted by TBP for following impurities are given: Fe(III), Fe(II), Co(II), Cu(II), Zn(II), Mn(II), Cr(III), Pb(II), Al(III), Bi(III), Sb(III) and Sn(IV).A continuous purification of the electrolyte by ion-exchange has been done in the refining of a ferronickel 94.4% in nickel. Nickel obtained is 99.74%.CaCl₂ 5 M appears to be a good electrolyte for electro-refining of nickel.     

Part 8. Preparation,characterization and metal complexing of poly[(2‐hydroxyethyl)‐DL‐aspartamide] in aqueous solution

Poly[(2‐hydroxyethyl)‐DL ‐aspartamide] was synthesized by polyreaction of aspartic acid and subsequent polymer‐analogous functionalization with ethanolamine. The water‐soluble polymer was characterized by FTIR, NMR, TGA and light‐scattering measurements. The metal complexing properties of the polymer were studied for Cr(III), Fe(III), Co(II), Ni(II), Cu(II), Zn(II), Sr(II), Cd(II) and Pb(II) ions in aqueous solution using the liquid‐phase polymer‐based retention (LPR) method. According to the retention profiles of LPR, Cr(III), Fe(III), Cu(II) and Pb(II) showed a strong interaction with this polymer under these conditions, indicated by retention values of about 100 %. In contrast, Co(II), Ni(II), Zn(II), Sr(II) and Cd(II) exhibited retention values of only 50–60 % in dilute solution at pH 5. © 2000 Society of Chemical Industry     

Resin. III. Synthesis,characterization, and ion-exchange properties of a 2,2′-dihydroxybiphenyl–formaldehyde copolymer resin

A 2,2′-dihydroxybiphenyl–formaldehyde copolymer, synthesized by the condensation of 2,2′-dihydroxybiphenyl with CH₂O in the presence of an acid catalyst, proved to be a selective chelating ion-exchange copolymer for certain metals. The chelating ion-exchange properties of this copolymer were studied for Fe(III), Cu(II), Ni(II), Zn(II), Cd(II), and Pb(II) ions. A batch equilibrium method was employed in the study of the selectivity of metal ion uptake, involving the measurements of the distribution of a given metal ion between the copolymer sample and the solution containing the metal ion. The study was carried out over a wide pH range and in media of various ionic strengths. The copolymer showed a higher selectivity for Fe(III), Cu(II), and Ni(II) ions than for Co(II), Zn(II), Cd(II), and Pb(II) ions. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Adsorption Behavior of Iminodiacetic Acid Type of Chelating Gel Prepared from Waste Paper

Abstract

Adsorption gel was prepared from waste recycled paper by immobilizing iminodiacetic acid (IDA) functional group by chemical modification. The gel exhibited good adsorption behavior for a number of metal ions viz. Cu(II), Pb(II), Fe(III), Ni(II), Cd(II), and Co(II) at acidic pH. The order of selectivity was found to be as follows: Cu(II)>Pb(II)>Fe(III)>Ni(II)～Cd(II)～Co(II). From the adsorption isotherms, the maximum adsorption capacity of the gel for both Cu(II) and Pb(II) was found to be 0.47 mol/kg whereas that for Cd(II) was 0.24 mol/kg. A continuous flow experiment for Cd(II) showed that the gel can be useful for pre‐concentration and complete removal of Cd(II) from aqueous solution.     

Activated carbon sorbent with thioetheric sites—preparation and characterization

An activated carbon sorbent containing thioetheric sites (ACTS) was prepared by modification of the activated carbon with 2,2′-thiodiethanol. The specific surface area, pore volume, concentration of oxygen-containing groups and sulfur content of the sorbent were determined. The sorption behavior towards ions of some precious metals—Au(III), Pt(IV), Pd(II) and heavy metals—Ni(II), Zn(II), Fe(III), Cu(II), Pb(II), Cd(II) and Co(II) was studied. Selectivity towards gold, palladium and platinum in the pH range 1–9 was observed. The capacity for gold was 80 mg g⁻¹. The sorption of Au(III) at pH 1 is not affected by milligram amounts of Ni(II), Zn(II), Fe(III), Cu(II), Pb(II), Cd(II) and Co(II). The sorbed gold species is Au(0).     

Synthesis,characterization, and catalytic activity of 4 mol % N,N′‐methylene bisacrylamide crosslinked poly(acrylic acid)–metal complexes

The metal‐ion complexation behavior and catalytic activity of 4 mol % N,N′‐methylene bisacrylamide crosslinked poly(acrylic acid) were investigated. The polymeric ligand was prepared by solution polymerization. The metal‐ion complexation was studied with Cr(III), Mn(II), Fe(III), Co(II), Ni(II), Cu(II), and Zn(II) ions. The metal uptake followed the order: Cu(II) > Cr(III) > Mn(II) > Co(II) > Fe(III) > Zn(II) > Ni(II). The polymeric ligand and the metal complexes were characterized by various spectral methods. The catalytic activity of the metal complexes were investigated toward the hydrolysis of p‐nitrophenyl acetate (NPA). The Co(II) complexes exhibited high catalytic activity. The kinetics of catalysis was first order. The hydrolysis was controlled by pH, time, amount of catalyst, and temperature. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 272–279, 2004     

Adsorption properties of poly(acrylaminophosphonic-carboxyl-hydrazide)type chelating fiber for heavy metal ions

In this article, the adsorption properties of poly(acrylaminophosphonic-carboxyl-hydrazide) chelating fibers for Cu(II), Cd(II), Co(II), Mn(II), Pb(II), Zn(II), Ni(II), and Cr(III) are investigated by a batch technique. Based on the research results of binding capacity, adsorption isotherm, effect of pH value on sorption, and adsorption kinetics experiments, it is shown that the poly(acrylaminophosphonic-carboxyl-hydrazide) chelating fibers have higher binding capacities and good adsorption kinetic properties for heavy metal ions. The sorption of the metal ions on the chelating fibers is strongly dependent on the equilibrium pH value of the solution. The adsorption isotherms of Cu(II) and Cd(II) on the chelating fiber exhibit a Langmuir-type equation. The adsorbed Cu(II), Cd(II), Zn(II), and Pb(II) could be eluted by diluted nitric acid. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 70: 7–14, 1998     

Cation effects in the oxidative coupling of methane on phosphate catalysts

The conversion of methane and the selectivities to the various products have been measured at 700 and 775 °C on a variety of phosphates of La(III), Zr(IV), V(V), Cr(III), Mn(III), Mn(II), Fe(III), Co(II), Ni(II), Cu(II), Zn(II), Al(III), B(III), Pb(II), Bi(III) and Sm(III) in the presence and absence of carbon tetrachloride. The conversions reach as high as 30 and 49% at 700 and 775 °C, respectively, with methane and oxygen at partial pressures of 200 and 25 Torr, respectively. The highest C₂₊ selectivities (61 and 82%, respectively) were obtained for lead(II) phosphate at 700 and 775 °C, respectively. In general the conversions and C₂₊ selectivities are enhanced on addition of carbon tetrachloride (1.1 Torr) to the feedstream, although there are notable exceptions. Significantly high selectivities to formaldehyde are observed with a number of the catalysts, in particular 32% with boron(III)phosphate.     

Metal sorption on macroporous poly(GMA-co-EGDMA) modified with ethylene diamine

Two samples of macroporous crosslinked poly(glycidyl methacrylate-co-ethylene glycol dimethacrylate), poly(GMA-co-EGDMA), with different porosity parameters were synthesized by suspension copolymerization and modified by ring-opening reaction of the pendant epoxy groups with ethylene diamine (EDA). The samples were characterized by mercury porosimetry, FT-IR spectroscopy and elemental analysis. The sorption rate of the modified copolymer, poly(GMA-co-EGDMA)-en for Cu(II) ions determined under non-competitive conditions was relatively rapid, i.e. the maximum capacity was reached within 30 min. Batch sorption capacities for Cu(II), Fe(II), Mn(II), Cd(II), Zn(II), Pb(II), Cr(III) and Pt(IV) ions were determined under non-competitive conditions in the pH range 1.25–5.5 at room temperature. The maximum sorption capacities of poly(GMA-co-EGDMA)-en under non-competitive conditions were 1.30 mmol/g for Pt(IV) at pH 5.5, 1.10 mmol/g for Cu(II) at pH 5.5, 1.06 mmol/g for Pb(II) at pH 1.25 and 0.67 mmol/g for Cd(II) ions at pH 5.5. The selectivity of poly(GMA-co-EGDMA)-en towards Cu(II), Co(II), Ni(II), Pb(II) and Pt(IV) ions was investigated under competitive conditions. Poly(GMA-co-EGDMA)-en showed high selectivity for Pt(IV) over Cu(II), Co(II), Ni(II) and Pb(II) ions at pH 2.1. At pH 5.5, the metal sorption capacities of poly(GMA-co-EGDMA)-en decreased in the order: Cu(II) > Co(II) > Pt(IV) ≈ Ni(II) > Pb(II). Regeneration of the Cu(II), Ni(II) and Pb(II) loaded poly(GMA-co-EGDMA)-en with 2 M H₂SO₄ showed that the polymer can be reused in several sorption/desorption cycles.     

Poly(sodium 4-styrenesulfonate)–metal ion interactions

The metal ion-binding properties of poly(sodium 4-styrenesulfonate) in conjunction with membrane filtration were investigated for Cu(II), Cd(II), Co(II), Cr(III), Hg(II), Ni(II), Pb(II), Zn(II), and Fe(II). Different experiments were carried out at different pH's, metal ion concentrations, polymer concentrations, and molecular weight fractions. Only Fe(II) and Cr(III) were retained at pH 1, which allows a selective separation of these metals from all the other metal ions. At pH 3 the retention ability of this polymer increased for all the metal ions. On the other hand, the metal ion-retention properties are dependent on the polymer/metal ratio. © 1998 John Wiley & Sons, Inc. J. Appl. Polym. Sci. 70: 219–225, 1998     

Cetylpyridinium chloride-modified poly(ethyleneimine) for the removal and separation of inorganic ions in aqueous solution

The removal and separation of a series of ions by the water-soluble cetylpyridinium chloride-modified poly(ethyleneimine) (PEI-CPC) in conjunction with membrane filtration were investigated. The Liquid-Phase Polymer-Based Retention (LPR) method was applied to study the removal of the low-molecular species at different pH values and at several element concentrations. The study comprises aqueous solutions of the anions chromate and phosphate, and of the cations Cu(II), Zn(II), Co(II), Ni(II), Cr(III), Fe(III), Cd(II), Pb(II) and Sr(II). The results show that a high retention was attained in neutral solutions for both anions and also for most metal ions investigated. PEI-CPC exhibited good removing abilities for chromate and phosphate ions even at relatively high concentrations of anions (85 and 150 mg · L ^?1, respectively) and also for most of the metal ions studied. In the case of Cu(II), Ni(II), Cd(II), and Sr(II) ions, selective interactions were observed. The polymer reagent and its interaction products were characterized by IR, UV/VIS spectrometry, and viscometry. In addition, the interaction behaviour was investigated by the retention ability. A good correlation was found between the retention data and the IR and UV/VIS spectra of the interaction products of the polymer reagent with the metal ions.     

REMOVAL OF METAL IONS FROM AQUEOUS SOLUTIONS USING PYROLYZED RICE HUSKS: ADSORPTION KINETICS AND EQUILIBRIA

Four carbon/silica-containing materials obtained by pyrolysis of rice husks were characterized and their adsorption properties towards some metal ions were evaluated. GC/MS analysis and FT-IR spectroscopy were applied for identification of functional groups finely dispersed on the surface. Their amounts were gravimetrically determined after extraction with acetone. The specific surface area and porosity of the materials were characterized by the Brunauer-Emmett-Teller (BET) method and by mercury porosimetry, respectively. The adsorption properties of the carbonized rice husks towards Fe(III), Pb(II), Cr(III), and Cu(II) ions in single- and multicomponent aqueous solutions also containing Ni(II), Co(II), Mn(II), and Cd(II) were studied in a batch system. The effects of contact time, acidity of initial solutions, and metal ion concentrations were followed. Pseudo-first-order, pseudo-second-order, and intraparticle diffusion models were used to analyze kinetic data. Equilibrium experimental data were fitted to linear Langmuir and Freundlich models. The maximum adsorption capacities for single- and multicomponent adsorption were calculated and compared with literature data. A correlation between the adsorption properties of pyrolyzed rice husks and their textural and surface parameters was established. Possibilities for desorption of the investigated ions were estimated.     

Synthesis and characterization of poly(acrylaminophosphonic-carboxyl-hydrazide) chelating fibre

The poly(acrylaminophosphonic-carboxyl-hydrazide) chelating ion exchange fibre was prepared by the amination and phosphorization reaction of the hydrazine-modified polyacrylonitrile fibre. The structure of the chelating fibre and the same fibre saturated by Cu(II) and Ag(I) ions was investigated by IR spectrometer in detail. In addition, the crystalline and surface characteristics of the chelating fibre were determined by X-ray diffraction and SEM. The higher binding capacities of the fibrous sorbent for Cu(II), Pb(II), Zn(II), Co(II), Ni(II), Hg(II), Cd(II), Mn(II), Cr(III) and Ag(I) and the effect of pH value on adsorption of the chelating fibre for Cu(II) and Hg(II) ions were examined.     

Analytical applications of newly synthesized copolymer resin derived from p‐aminophenol,dithiooxamide, and formaldehyde

A copolymer resin (p‐APDF) has been synthesized using the monomers p‐aminophenol, dithiooxamide, formaldehyde in 1 : 1 : 2M proportions in the presence of 2M HCl as catalyst. The structure of p‐APDF copolymer has been elucidated on the basis of elemental analysis and various physicochemical techniques, i.e., UV‐visible, FTIR, and ¹H‐NMR spectroscopy. The number average molecular weight of copolymer resin was determined by nonaqueous conductometric titration in DMF. Viscosity measurement were carried out in DMF indicate normal behavior. The prepared resin proved to be a selective ion exchange resin for some metal ions. The chelating ion exchange properties of this resin was studied for Fe(III) and Cu(II), Ni(II), Co(II), Zn(II), Cd(II), Pb(II) ions. A batch equilibrium method was used to study selectivity of metal ion uptake over a wide pH range and in media of various ionic strength. The resin showed a higher selectivity for Fe(III), Ni(II), Cu(II) ions than for Co(II), Pb(II), Zn(II), and Cd(II) ions. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Application of Chitosan Membranes in Separation of Heavy Metal Ions

Abstract

The authors present an application of chitosan membranes for the removal of heavy metal ions. Investigations covered membranes produced by phase inversion. Additionally, separation properties of acetylated membranes were tested. Low-viscous chitosan produced by the Sea Fisheries Institute—Poland was used in the experiments. The investigations were carried out for the transition metal ions Cr(VI), Mn(II), Fe(III), Co(II), Ni(II), Cu(II), Zn(II), and Cd(II). A method for metal ions separation by means of chitosan membranes was proposed. The metal ions were complexed in the membrane during ultrafiltration of the solution. The separation ability of the membranes was investigated for individual metal ions and for a mixture. The effect of the pH of the solution on separation properties of membranes was determined. The concentration of metal ions was investigated by the method of inductively coupled plasma (ICP) atomic emission spectrometry. The investigations show the suitability of chitosan membranes produced by the phase inversion method for the removal of metal ions.     

Synthesis and properties of hydrophilic polymers. IX. Synthesis,biodegradability, and metal complexation of copolymers of ethylenediaminetetraacetic acid dianhydride and lactose

The synthesis and characterization of poly(ethylenediaminetetraacetic acid‐co‐lactose) with pendant carboxylic groups of high molar mass (132 kg mol^?1) is described. The polycondensate was hydrolytically and microbiologically degradable with conventional microbiological methods. The metal‐complexing properties of the polyester were studied for Cr(III), Fe(III), Co(II), Ni(II), Cu(II), Zn(II), Sr(II), Cd(II), Pb(II), and Al(III) ions in aqueous solution with the liquid‐phase polymer‐based retention (LPR) method. In addition, the complexing capacity of the Cu(II)‐saturated copolymer was determined by thermogravimetric analysis to be 182 mg g^?1 of polymer. According to the retention profiles determined as a function of the filtration factor with LPR in conjunction with inductively coupled plasma spectrometry, Cr(III) and Fe(III) showed a strong interaction with this polymer under these conditions, as indicated by retention values of about 100% at pH 5. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 650–657, 2003     

Synthesis and properties of hydrophilic polymers,part 11: Synthesis,biodegradability, and metal complexation of copolymers of ethylenediaminetetraacetic acid dianhydride and lactose

The synthesis and characterization of poly(ethylenediaminetetraacetic acid‐co‐lactose) of high molar mass (132 kg mol^?1) is described. The polycondensate with pendant carboxylic groups was shown to be hydrolytically and microbiologically degradable by using conventional microbiological methods. The metal complexing properties of the polyester were studied for Cr(III), Fe(III), Co(II), Ni(II), Cu(II), Zn(II), Sr(II), Cd(II), Pb(II), and Al(III) ions in aqueous solution using the liquid‐phase polymer‐based retention (LPR) method. In addition, the complexing capacity of the Cu(II)‐saturated copolymer was determined by TGA to be 182 mg g^?1 polymer. According to the retention profiles determined as a function of filtration factor by using LPR in conjunction with inductively coupled plasma spectrometry, Cr(III) and Fe(III) showed a strong interaction with this polymer under these conditions, indicated by retention values of 100% at pH 5. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 2932–2939, 2007     

Synthesis,Characterization, and Applications of a New Chelating Resin Containing 4-2-(Thiazolylazo) Resorcinol (TAR)

A new phenol–formaldehyde based chelating resin containing 4-(2-thiazolylazo) resorcinol (TAR) functional groups has been synthesized and characterized by Fourier transform infrared spectroscopy and elemental analysis. Its adsorption behavior for Cu(II), Pb(II), Ni(II), Co(II), Cd(II), and Mn(II) has been investigated by batch and column experiments. The chelating resin is highly selective for Cu(II) in the pH range 2 ～ 3, whereas alkali metal and alkaline earth metal ions such as Na(I), Mg(II), and Ca(II) are not adsorbed even at pH 6. Quantitative recovery of most metal ions studied in this work except Co(II) is achieved by elution with 2M HNO₃ at a flow rate of 0.2 mL min^?1. A similar trend is observed for distribution coefficient values. The quantitative separations achieved on a mini-column of chelating resin include Cd(II) – Cu(II), Mn(II) – Pb(II), Co(II) – Cu(II), Mn(II) – Ni(II), and Mn(II) – Co(II) – Cu(II). The recovery of copper(II) is quantitative (98.0–99.0%) from test solutions (10–50 mg/L) by 1 mol/L HNO₃-0.01 mol/L EDTA. The chelating resin is stable in acidic solutions below 2.5 M HNO₃ or HCl as well as in alkaline solution below pH 11. The adsorption behavior of the resin towards Cu(II) was found to follow Langmuir isotherm and second order rate.     

Preparation of amidoximated polyester fiber and competitive adsorption of some heavy metal ions from aqueous solution onto this fiber

In this study, a fibrous adsorbent containing amidoxime groups was prepared by graft copolymerization of acrylonitrile (AN) onto poly(ethylene terephthalate) (PET) fibers using benzoyl peroxide (Bz₂O₂) as initiator in aqueous solution, and subsequent chemical modification of cyano groups by reaction with hydroxylamine hydrochloride in methanol. The grafted and modified fibers were characterized by FTIR, TGA, SEM, and XRD analysis. The crystallinity increased, but thermal stability decreased with grafting and amidoximation. The removal of Cu(II), Ni(II), Co(II), Pb(II), and Cd(II) ions from aqueous solution onto chelating fibers were studied using batch adsorption method. These properties were investigated under competitive conditions. The effects of the pH, contact time, and initial ion concentration on the removal percentage of ions were studied. The results show that the adsorption rate of metal ions followed the given order Co(II) > Pb(II) > Cd(II) > Ni(II) > Cu(II). The percentage removal of ions increased with initial ion concentration, shaking time, and pH of the medium. Total metal ion removal capacity was 49.75 mg/g fiber on amidoximated fiber. It was observed that amidoximated fibers can be regenerated by acid without losing their activity, and it is more selective for Pb(II) ions in the mixed solution of Pb‐Cu‐Ni–Co‐Cd at pH 4. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Macromolecular Chelator‐Amberlite XAD‐16 Anchored with 2,3‐Dihydroxypyridine (DHP) for Enrichment of Metal Ions before their Determination by Flame Atomic Absorption Spectrometry

Abstract

2,3‐Dihydroxypyridine (DHP) was loaded onto Amberlite XAD‐16 via azo linker and the resulting resin AXAD‐16‐DHP explored for enrichment of Zn(II), Mn(II), Ni(II), Pb(II), Cd(II), Cu(II), Fe(III), and Co(II) in the pH range 4.0–6.5. The sorption capacity was found in the range 120–512 µmol g^?1 and the preconcentration factor from 200 to 300. Tolerance limits for foreign species are reported. The kinetics of sorption is fast, as t_1/2 is generally ≤2 min. The chelating resin can be reused for fifty cycles of sorption‐desorption without any significant change (≤2.0%) in its sorption capacity. The limit of detection values (blank + 3s) are 2.90, 3.80, 5.17, 7.02, 1.91, 1.63, 4.59, and 5.02 µg L^?1 for Zn, Mn, Ni, Pb, Cd, Cu, Fe, and Co respectively. The corresponding limit of quantification (blank + 10 s) values are 5.30, 6.20, 8.38, 9.54, 4.22, 4.17, 8.62, and 9.86 µg L^?1, respectively. The enrichment on AXAD‐16‐DHP coupled with monitoring by flame atomic absorption spectrometry (FAAS) is used to determine these metal ions in river and synthetic water samples, Co in vitamin tablets, and Zn in milk samples. AXAD‐16‐DHP has been found to perform better than DHP loaded cellulose and Amberlite XAD‐2.