Synthesis and photoluminescence properties of aligned Zn2GeO4 coated ZnO nanorods and Ge doped ZnO nanocombs

Aligned Zn₂GeO₄ coated ZnO nanorods and Ge doped ZnO nanocombs were synthesized on a silicon substrate by a simple thermal evaporation method. The structure and morphology of the as-synthesized nanostructure were characterized using scanning electron microscopy and transmission electron microscopy. The growth of aligned Zn₂GeO₄ coated ZnO nanorods and Ge doped ZnO nanocombs follows a vapor-solid (VS) process. Photoluminescence properties were also investigated at room temperature. The photoluminescence spectrum reveals the nanostructures have a sharp ultraviolet luminescence peak centered at 382 nm and a broad green luminescence peak centered at about 494 nm.     

Characterization and humidity sensing of ZnO/42° YX LiTaO3 Love wave devices with ZnO nanorods

Love mode surface acoustic wave devices based on ZnO/42° YX LiTaO₃ were characterized with the thickness of the sputtered ZnO guiding layer varied from 250 nm to 1.18 μm. Phase velocity, temperature coefficient of resonant frequency, sensitivity, electromechanical coupling coefficient and humidity sensing of the Love mode SAW devices were studied as a function of the ZnO layer thickness. With increasing ZnO thickness over the range of thickness values we have examined, the sensitivity of 42° YX LiTaO₃ to liquid loading increased and the values of electromechanical coupling coefficient decreased. The device with a thickness of 250 nm showed the best humidity response. ZnO nanorods were grown on this device and its humidity sensing performance has been further improved due to their large surface-to-volume ratio of the ZnO nanorods.     

A comparative study on the NO2 gas sensing properties of ZnO thin films, nanowires and nanorods

ZnO thin films were fabricated using the spin coating method, ZnO nanowires by cathodically induced sol-gel deposition by the means of an anodic aluminum oxide (AAO) template, and ZnO nanorods with the hydrothermal technique. For thin film preparation, a clear, homogeneous and stable ZnO solution was prepared by the sol-gel method using zinc acetate (ZnAc) precursor which was then coated on a glass substrate with a spin coater. Vertically aligned ZnO nanowires which were approximately 65 nm in diameter and 10 μm in length were grown in an AAO template by applying a cathodic voltage in aqueous zinc nitrate solution at room temperature. For fabrication of the ZnO nanorods, the sol-gel ZnO solution was coated on glass substrate by spin coating as a seed layer. Then ZnO nanorods were grown in zinc nitrate and hexamthylenetetramine aqueous solution. The ZnO nanorods are approximately 30 nm in diameter and 500 nm in length. The ZnO thin film, ZnO nanowires and nanorods were characterized by X-ray diffraction (XRD) analysis and scanning electron microscope (SEM). The NO₂ gas sensing properties of ZnO thin films, nanowires and nanorods were investigated in a dark chamber at 200 °C in the concentration range of 100 ppb-10 ppm. It was found that the response times of both ZnO thin films and ZnO nanorods were approximately 30 s, and the sensor response was depended on shape and size of ZnO nanostructures and electrode configurations.     

Sensing behaviour of nanosized zinc-tin composite oxide towards liquefied petroleum gas and ethanol

A chemical route has been used to synthesize composite oxides of zinc and tin. An ammonia solution was added to equal amounts of zinc and tin chloride solutions of same molarities to obtain precipitates. Three portions of these precipitates were annealed at 400, 600 and 800 °C, respectively. Results of X-ray diffraction and transmission electron microscopy clearly depicted coexistence of phases of nano-sized SnO₂, ZnO, Zn₂SnO₄ and ZnSnO₃. The effect of annealing on structure, morphology and sensing has been observed as well. It has been observed that annealing promoted growth of Zn₂SnO₄ and ZnSnO₃ at the expense of zinc. The sensing response of fabricated sensors from these materials to 250 ppm LPG and ethanol has been investigated. The sensor fabricated from powder annealed at 400 °C responded better to LPG than ethanol.     

An efficient room-temperature route to uniform ZnO nanorods with an ionic liquid

Rod-like ZnO nanocrystals have been synthesized via an ultrasound-assisted way by the reaction between Zn(CH₃COO)₂·2H₂O and NaOH in the ionic liquid 1-butyl-3-methyl imidazole six hexafluorophosphoric acid salts ([BMIM][PF₆]) aqueous solution. The products were characterized by XRD, EDX, FESEM, TEM, HRTEM, UV-Vis and PL techniques. The as-prepared ZnO nanorods have a diameter of about 50 nm and a length of 1-2 μm. A plausible four-step mechanism was proposed to explain the formation of ZnO nanorods. It was found that the lowered ion diffusion velocity in the water-ionic liquid medium could largely contribute to the formation of the ZnO nanorods. The effects of experimental parameters on the formation of the products were also explored.     

Facile synthesis of highly branched jacks-like ZnO nanorods and their applications in dye-sensitized solar cells

Highly branched, jacks-like ZnO nanorods architecture were explored as a photoanode in dye-sensitized solar cells, and their photovoltaic performance was compared with that of branch-free ZnO nanorods photoanodes. The highly branched network and large pores of the jacks-like ZnO nanorods electrodes enhances the charge transport, and electrolyte penetration. Thus, the jacks-like ZnO nanorods DSSCs render a higher conversion efficiency of η = 1.82% (V_oc = 0.59 V, J_sc = 5.52 mA cm⁻²) than that of the branch-free ZnO nanorods electrodes (η = 1.08%, V_oc = 0.49 V, J_sc = 4.02 mA cm⁻²). The incident photon-to-current conversion efficiency measurements reveal that the jacks-like ZnO nanorods DSSCs exhibit higher internal quantum efficiency (∼59.1%) than do the branch-free ZnO nanorods DSSC (∼52.5%). The charge transfer resistances at the ZnO/dye/electrolyte interfaces investigated using electrochemical impedance spectroscopy showed that the jacks-like ZnO nanorods DSSC had high charge transfer resistance and a slightly longer electron lifetime, thus improving the solar-cell performance.     

Low temperature solution synthesis and characterization of ZnO nano-flowers

Synthesis of flower-shaped ZnO nanostructures composed of hexagonal ZnO nanorods was achieved by the solution process using zinc acetate dihydrate and sodium hydroxide at very low temperature of 90 °C in 30 min. The individual nanorods are of hexagonal shape with sharp tip, and base diameter of about 300-350 nm. Detailed structural characterizations demonstrate that the synthesized products are single crystalline with the wurtzite hexagonal phase, grown along the [0 0 0 1] direction. The IR spectrum shows the standard peak of zinc oxide at 523 cm⁻¹. Raman scattering exhibits a sharp and strong E₂ mode at 437 cm⁻¹ which further confirms the good crystallinity and wurtzite hexagonal phase of the grown nanostructures. The photoelectron spectroscopic measurement shows the presence of Zn, O, C, zinc acetate and Na. The binding energy ca. 1021.2 eV (Zn 2p_3/2) and 1044.3 eV (Zn 2p_1/2), are found very close to the standard bulk ZnO binding energy values. The O 1s peak is found centered at 531.4 eV with a shoulder at 529.8 eV. Room-temperature photoluminescence (PL) demonstrate a strong and dominated peak at 381 nm with a suppressed and broad green emission at 515 nm, suggests that the flower-shaped ZnO nanostructures have good optical properties with very less structural defects.     

Vapor phase growth and optical properties of single-crystalline SnO2 nanobelts

Mass production of single-crystalline SnO₂ nanobelts was successfully achieved through a thermal evaporation of metallic Sn powders at 900 °C. The as-prepared SnO₂ nanobelts were typically 30-200 nm in width, 10-50 nm in thickness, and about tens of micrometers in length. In addition to the classical Raman models, two new Raman bands at 498 and 698 cm⁻¹ are observed for rutile-phased SnO₂ nanobelts, which can be attributed to the IR-active A_2u TO and A_2u LO modes, respectively. Photoluminescence (PL) spectrum of SnO₂ nanobelts featured an emission band at 615 nm (with a small shoulder at 585 nm), which might correspond to the existence of oxygen deficiencies in the produced belts. The formation of SnO₂ nanobelts followed a vapor-solid (VS) growth mechanism.     

Sub-2 nm SnO2 nanocrystals: A reduction/oxidation chemical reaction synthesis and optical properties

A simple reduction/oxidation chemical solution approach at room temperature has been developed to synthesize ultrafine SnO₂ nanocrystals, in which NaBH₄ is used as a reducing agent instead of mineralizers such as sodium hydroxide, ammonia, and alcohol. The morphology, structure, and optical property of the ultrafine SnO₂ nanocrystals have been characterized by high-resolution transmission electron microscopy (HRTEM), X-ray powder diffraction (XRD), differential scanning calorimetry and thermogravimetric analysis (DSC-TGA), X-ray photoelectron spectroscopy (XPS) and UV-vis absorption spectroscopy. It is indicated that the uniform tetragonal ultrafine SnO₂ nanocrystals with the size below 2 nm have been fabricated at room temperature. The band gap of the ultrafine SnO₂ nanocrystals is about 4.1 eV, exhibiting 0.5 eV blue shift from that of the bulk SnO₂ (3.6 eV). Furthermore, the mechanism for the reduction/oxidation chemical reaction synthesis of the ultrafine SnO₂ nanocrystals has been preliminary presented.     

A rapid and efficient method to prepare aligned SnO2 nanorod arrays for field-emission application

Aligned tin dioxide (SnO₂) nanorods have been synthesized by high-frequency inductive heating. Nanorods were grown on silicon substrates vertically in less than 3 min, using SnO₂ and graphite as the source powder. Scanning electron microscopy and transmission electron microscopy showed nanorod with diameters from 25 to 50 nm. The turn-on field needed to produce a current density of 10 μA/cm² is found to be 1.6 V/μm. This type of SnO₂ nanorods can be applied as field emitters in displays as well as vacuum electric devices.     

Highly selective ethanol In2O3-based gas sensor

The sensitive composite material was prepared by loading Pt and La₂O₃ into ultrafine In₂O₃ matric material (8 nm) synthesized by microemulsion method. A highly selective ethanol gas sensor was developed based on hot-wire type gas sensor, which was sintered in a bead (0.8 mm in diameter) to cover a platinum wire coil (0.4 mm in diameter). The gas sensor was operated by a bridge electric circuit. The influences of La₂O₃ and Pt additives on C₂H₅OH sensing properties of In₂O₃-based gas sensor were discussed. The addition of La₂O₃ resulted in a prominent selectivity for C₂H₅OH, and the addition of Pt improved the response rate to C₂H₅OH without affecting the sensitivity. The temperature and humidity characteristics of the sensor output were also investigated. The selective sensor had low power consumption, significantly minor humidity and temperature dependence, high selectivity and prominent long-term stability.     

Tin dioxide nanoparticles: Reverse micellar synthesis and gas sensing properties

Tin dioxide (SnO₂) nanoparticles have been synthesized by reverse micellar route using cetyltrimethyl ammoniumbromide (CTAB) as the surfactant. Monophasic tin dioxide (SnO₂) was obtained using NaOH as the precipitation agent at 60 °C, however, when liquor NH₃ was used as precipitating agent then crystalline SnO₂ nanoparticles are obtained at 500 °C. SnO₂ prepared using NaOH show crystallite size of 4 and 12 nm after heating at 60 and 500 °C respectively using X-ray line broadening studies. Transmission electron microscopy (TEM) studies show agglomerated particles of sizes 70 and 150 nm, respectively. The grain size was found to be 6-8 nm after heating the precursor obtained (using liquor NH₃) at 500 °C by X-ray line broadening and the TEM studies. Dynamic light-scattering (DLS) studies show the aggregates of SnO₂ nanoparticles with uniform size distribution. Mössbauer studies show an increase of s-electron density at the Sn sites compared to bulk SnO₂ and a finite quadrupole splitting indicative of lowering of symmetry around tin atoms. The gas sensing characteristics have also been investigated using n-butane which show high sensitivity and fast recovery time.     

PEG-300 assisted hydrothermal synthesis of 4ZnO·B2O3·H2O nanorods

4ZnO·B₂O₃·H₂O is commonly used as a flame-retardant filler in composite materials. The microstructure of the powder is of importance in its applications. In our study, for the first time, one-dimensional (1D) nanostructure of 4ZnO·B₂O₃·H₂O with rectangle rod-like shape has been synthesized by a hydrothermal route in the presence of surfactant polyethylene glycol-300 (PEG-300). The nanorods have been characterized by X-ray powder diffraction (XRD), inductively coupled plasma with atomic emission spectroscopy (ICP-AES), thermogravimetry (TG) and differential thermal analysis (DTA), scanning electron microscopy (SEM), transmission electron microscopy (TEM) equipped with selected area electron diffraction (SAED) as well as high-resolution transmission electron microscopy (HRTEM). These nanorods are about 70 nm in thickness, 150-800 nm in width and have lengths up to a few microns. 4ZnO·B₂O₃·H₂O nanorods crystallize in the monoclinic space group P2₁/m, a = 6.8871(19) Å, b = 4.9318(10) Å, c = 5.7137(16) Å, β = 98.81(21)° and V = 191.779(71) Å³.     

Synthesis and gas sensing properties of novel SnO2 nanorods

We report the microstructures and gas sensing properties of two novel SnO₂ nanorods prepared by hydrothermal method with the utilizing of cetyltrimethylammonium bromide and polyethylene glycol. The structures and morphologies of the dense and porous nanorods were characterized by means of powder X-ray diffraction and scanning electron microscopy. The gas sensing performances towards ethanol of the two samples were investigated. The results show that the porous SnO₂ nanorods display excellent gas response to ethanol, indicating SnO₂ as a potential gas sensing material for broad applications.     

Solvothermal synthesis of nanorods of ZnO, N-doped ZnO and CdO

ZnO nanorods with diameters in the 80-800 nm range are readily synthesized by the reaction of zinc acetate, ethanol and ethylenediamine under solvothermal conditions. The best products are obtained at 330 °C with a slow heating rate. Addition of the surfactant Triton^®-X 100 gave nanorods of uniform (300 nm) diameter. By adding a small amount of liquid NH₃ to the reaction mixture, N-doped ZnO nanorods, with distinct spectroscopic features are obtained. CdO nanorods of 80 nm diameter have been prepared under solvothermal conditions using a mixture of cadmium cupferronate, ethylenediamine and ethanol at 330 °C. Similarly, Zn_1−xCd_xO nanorods of a 70 nm diameter are obtained under solvothermal conditions starting with a mixture of zinc acetate, cadmium cupferronate, ethanol and ethylenediamine.     

Vertically aligned Mn-doped zinc oxide nanorods by hybrid wet chemical route

Mn-doped zinc oxide (Mn:ZnO) nanorods were synthesized by incorporating manganese in aligned ZnO nanorods. For this, Mn was evaporated onto ZnO nanorods and the composite structure was subjected to rapid thermal annealing. The nanorods were preferentially oriented in (0 0 2) direction as indicated by the XRD measurement. Optical band gap was seen to decrease with increasing amount of Mn incorporation. XPS studies indicated that incorporated Mn was in Mn²⁺ and Mn⁴⁺ states. Mn²⁺ atomic concentration was found to be larger than Mn⁴⁺ concentration in all the samples. The Raman spectra of the Mn:ZnO nanorods indicated the presence of the characteristic peak at ∼438 cm⁻¹ for high frequency branch of E₂ mode of ZnO. The PL peak at ∼376 nm (∼3.29 eV) was ascribed to the band edge luminescence while the peak at ∼394 nm (∼3.15 eV) was assigned to the donor bound exciton (D^oX) and free exciton transition related to Mn²⁺ states.     

From tin oxalate to (Fe, Co, Nb)-doped SnO2: Sintering behavior, microstructural and electrical features

Highly reactive SnO₂-doped nanocrystalline powders with average particle size of 20 nm and specific surface areas above 30 m²/g were obtained through the polymeric precursor method with tin oxalate (SnC₂O₄) as a chloride-free precursor for SnO₂. Powders and sintered discs were characterized by means of X-ray powder diffraction (XRD), SEM and TEM. The influence of Co and Fe on the microstructure development and on the electrical properties of dense SnO₂-based ceramics was studied. Co and Fe species were found to decrease in more than 70 °C the sintering temperature of SnO₂ with respect to mixed oxide procedures. Secondary phases enriched in Co and Fe were detected and identified in sintered samples with XRD. Current-voltage curves were registered for electrical characterization. Doping with iron increased the electrical breakdown field and a nonlinearity coefficient of 20 was achieved.     

Low temperature extrusion of 6061 aluminum matrix composite reinforced with SnO2-coated Al18B4O33 whisker

The 6061 aluminum matrix composite reinforced with SnO₂-coated Al₁₈B₄O₃₃ whisker was fabricated by squeeze casting and following by extrusion extruded at elevated temperatures from 300 °C to 400 °C. Optimization of the extruding process, microstructure, texture and mechanical properties of the extruded composites were investigated. The lowest extrusion temperature at which a composite rod with high surface quality was successfully produced was 300 °C. The yield strength of composites is much improved after extrusion, and especially their elongation is increased by 300%. Such big improvements depend on a fact that SnO₂ coating can introduce low-melting-point Sn phase into the interface through an interfacial reaction. The melting of interphase and their surrounding areas is the main reason for the excellent extrusion ability of the composite. Besides, detailed X-ray diffraction analysis of the extruded composite textures reveals the significant effects of extrusion temperatures on their features.     

Ni-doped vertically aligned zinc oxide nanorods prepared by hybrid wet chemical route

Ni-doped zinc oxide (Ni:ZnO) nanorods were synthesized by incorporating nickel in vertically aligned ZnO nanorods. Ni was evaporated onto ZnO nanorods and the composite structure was subjected to rapid thermal annealing for dispersing Ni in ZnO nanorods. The optical band gap decreased with increasing amount of Ni incorporation. The origin of the photoluminescence peak at ∼ 400 nm was related to the defect levels introduced due to substitution of Ni²⁺ in the Zn²⁺ site with annealing. The Raman spectra indicated the presence of the characteristic peak at ∼ 436 cm^− 1 which was identified as high frequency branch of E₂ mode of ZnO. The Fourier Transformed Infrared spectra indicated the existence of the distinct characteristic absorption peak at 481 cm^− 1 for ZnO stretching modes. Current-voltage characteristics indicated that the current changed linearly with voltage for both the doped and undoped samples.     

Morphology effect on the performances of SnO2 nanorod arrays as anodes for Li-ion batteries

Ni foam suppported-SnO₂ nanorod arrays with controllable diameter were prepared via a template-free growth method, which was a convenient route for the large-scale growth of pure-phase metal oxide nanorod arrays on metal substrates. The relationship between electrochemical behavior and the shape of SnO₂ nanorod arrays has been investigated in detail. SnO₂ nanorod arrays with diameter of about 25 nm, as anode materials for Li-ion batteries revealed a capacity of 607 mAh g⁻¹ (at 0.2 C) up to 50 cycles. The superior performance of the SnO₂ nanorods can be mainly attributed to small size of nanorods which reduce volume expansion and lithium diffusion length.