Application of bismuth-film electrode for cathodic electroanalytical determination of sulfadiazine

A bismuth-film electrode for use in cathodic electrochemical detection was employed in order to quantify sulfadiazine in pharmaceutical formulations. The bismuth film was deposited ex situ onto a glassy carbon substrate. Analysis of two sulfa drugs was carried out by differential-pulse voltammetry in 0.05 mol L⁻¹ Britton-Robinson pH 4.5 solution. Sulfadiazine reduction was observed at −0.74 V vs. Ag/AgCl in one well-resolved irreversible reduction peak. The analytical curve with two slopes was obtained in the concentration range of 3.2-97.0 μmol L⁻¹. The detection limit was 2.1 μmol L⁻¹ for concentrations of 3.2-20.0 μmol L⁻¹ (r = 0.9949) and 12.2 μmol L⁻¹ for concentrations between 20.0 and 97.0 μmol L⁻¹ (r = 0.9951). Recovery studies carried out with both sulfadiazine samples gave values from 93.6 to 109.3%. The accuracy of the results supplied by the bismuth-film electrode was compared to those obtained by the standard amperometric titration method. The relative error between them was lower than 2.0%.     

The ultrasonic electropolymerization of an 5-[o-(4-bromine amyloxy)phenyl]-10,15,20-triphenylporphrin (o-BrPETPP) film electrode and its electrocatalytic properties to dopamine oxidation in aqueous solution

5-[o-(4-Bromine amyloxy)phenyl]-10,15,20-triphenylporphrin (o-BrPETPP) was electropolymerized on a glassy carbon electrode (GCE), and the electrocatalytic properties of the prepared film electrode response to dopamine (DA) oxidation were investigated. A stable o-BrPETPP film was formed on the GCE under ultrasonic irradiation through a potentiodynamic process in 0.1 M H₂SO₄ between −1.1 V and 2.2 V versus a saturated calomel electrode (SCE) at a scan rate of 0.1 V s⁻¹. The film electrode showed high selectivity for DA in the presence of ascorbic acid (AA) and uric acid (UA), and a 6-fold greater sensitivity to DA than that of the bare GCE. In the 0.05 mol L⁻¹ phosphate buffer (pH 6.0), there was a linear relationship between the oxidation current and the concentration of DA solution in the range of 5 × 10⁻⁷ mol L⁻¹ to 3 × 10⁻⁵ mol L⁻¹. The electrode had a detection limit of 6.0 × 10⁻⁸ mol L⁻¹(S/N = 3) when the differential pulse voltammetric (DPV) method was used. In addition, the charge transfer rate constant k = 0.0703 cm s⁻¹, the transfer coefficient α = 0.709, the electron number involved in the rate determining step n_α = 0.952, and the diffusion coefficient D_o = 3.54  10⁻⁵ cm² s⁻¹ were determined. The o-BrPETPP film electrode provides high stability, sensitivity, and selectivity for DA oxidation.     

Preparation, electrochemical behavior and performance of gallium hexacyanoferrate as electrocatalyst of H2O2

The gallium hexacyanoferrate (GaHCF) was synthesized chemically and characterized by FTIR technique. Its electrochemical behavior was carefully investigated by fabricating a GaHCF modified carbon paste electrode in various supporting electrolyte. The experimental results showed that in KNO₃, K₂SO₄, KCl and other supporting electrolyte, GaHCF yielded one pair of ill-defined redox waves with a formal potential of 0.9 V (versus SCE). In 0.050 mol L⁻¹ phosphate buffer solution (PBS, pH 6.8), however, GaHCF yielded one pair of well-defined redox peaks with a formal potential of 0.222 V. Furthermore, this modified electrode exhibited a high electrocatalytic activity toward the reduction of H₂O₂ in pH 6.8 PBS, with over-potential dramatically lower than that of on the bare carbon paste electrode. Amperometry was used for the determination of H₂O₂, under the optimal conditions, a linear dependence of the catalytic current versus H₂O₂ concentration was obtained in the range of 4.9 × 10⁻⁶ to 4.0 × 10⁻⁴ mol L⁻¹ with a detection limit of 1 × 10⁻⁶ mol L⁻¹ when the signal-to-noise ratio was 3, and a sensitivity of 27.9 μA mM⁻¹ (correlation coefficient of 0.997). Chronoamperometry was used to conveniently determine the diffusion coefficient of H₂O₂ in the solution.     

Catalytic reduction of hydrogen peroxide at metal hexacyanoferrate composite electrodes and applications in enzymatic analysis

The electrocatalytic activity of various metal hexacyanoferrates (Mhcfs) (i) immobilized on graphite electrodes, and (ii) as components of a composite electrode was investigated with respect to the reduction of hydrogen peroxide. The flow-through working electrode was a thin layer consisting of a composite of Mhcf, graphite, and polymethylmetacrylate (PMMA) as a binder, sandwiched between two Plexiglas plates. Among the pure Mhcfs immobilized on a graphite electrode, iron(III) hexacyanoferrate (Prussian blue) exhibits the highest electrocatalytic effect, whereas in the composite electrodes chromium(III) hexacyanoferrate (Crhcf) shows the highest activity and best performance and reproducibility for the electrochemical reduction of H₂O₂. The Crhcf electrode provides a linear dependence on H₂O₂ concentration in the range 2.5 × 10⁻⁶ mol L⁻¹ (LOD) to 1 × 10⁻⁴ mol L⁻¹ (phosphate buffer, pH 7). The sensor was applied for the detection of H₂O₂ enzymatically produced by glucose oxidase. The optimal conditions for the peroxide injection were 2 min after the beginning of the reaction and 25 °C with a detection limit of 7.0 × 10⁻⁶ mol L⁻¹ for glucose.     

Direct electrochemistry and electrocatalysis of cytochrome c based on chitosan-room temperature ionic liquid-carbon nanotubes composite

A robust and effective composite film combined the benefits of room temperature ionic liquid (RTIL), chitosan (Chi) and multi-wall carbon nanotubes (MWNTs) was prepared. Cytochrome c (Cyt c) was successfully immobilized on glassy carbon electrode (GCE) surface by entrapping in the composite film. Direct electrochemistry and electrocatalysis of immobilized Cyt c were investigated in detail. A pair of well-defined and quasi-reversible redox peaks of Cyt c was obtained in 0.1 mol L⁻¹ pH 7.0 phosphate buffer solution (PBS), indicating the Chi-RTIL-MWNTs film showed an obvious promotion for the direct electron transfer between Cyt c and the underlying electrode. The immobilized Cyt c exhibited an excellent electrocatalytic activity towards the reduction of H₂O₂. The catalysis current was linear to H₂O₂ concentration in the range of 2.0 × 10⁻⁶ to 2.6 × 10⁻⁴ mol L⁻¹, with a detection limit of 8.0 × 10⁻⁷ mol L⁻¹ (S/N = 3). The apparent Michaelis-Menten constant (K_m) was calculated to be 0.45 ± 0.02 mmol L⁻¹. Moreover, the modified electrode displayed a rapid response (5 s) to H₂O₂, and possessed good stability and reproducibility. Based on the composite film, a third-generation reagentless biosensor could be constructed for the determination of H₂O₂.     

An electrochemical methanol sensor based on a Pd-Ni/SiNWs catalytic electrode

A novel electrochemical methanol sensor based on a catalytic electrode of palladium-nickel/silicon nanowires (Pd-Ni/SiNWs) is presented in this paper. Scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), and electrochemical methods are employed to investigate the Pd-Ni/SiNWs electrode materials. These nanocomposite materials exhibit a highly ordered, wire-like structure with a wire length of ∼50 μm and a wire diameter ranging from 100 to 300 nm. The substrate has good electrocatalytic activity towards the oxidation of methanol in alkaline solutions. The performances of the prototype sensor are characterized by cyclic voltammetry and fixed potential amperometry techniques. In a 1 mol L⁻¹ KOH solution containing different methanol concentrations, the sensor exhibits a good sensitivity of 1.96 mA mmol⁻¹ L cm⁻² with R² = 0.99 and the corresponding detection limit of 18 μmol L⁻¹ (signal-to-noise ratio = 3, S/N = 3) for cyclic voltammetry. Meanwhile, the electrode also displays a sensitivity of 0.48 mA mmol⁻¹ L cm⁻² with R² = 0.98 and the corresponding detection limit of 25 μmol L⁻¹ (S/N = 3) for a fixed potential amperometry at −0.3 V versus an Ag/AgCl reference electrode. The results demonstrate that the Pd-Ni/SiNWs catalytic electrode has potential as an efficient and integrated sensor for methanol detection.     

Development of a voltammetric sensor based on a molecularly imprinted polymer (MIP) for caffeine measurement

A new voltammetric sensor for caffeine measurement is introduced. A caffeine-selective molecularly imprinted polymer (MIP) and a non-imprinted polymer (NIP) were synthesized and then used for carbon paste (CP) electrode preparation. The MIP, embedded in the carbon paste electrode, functioned as a selective recognition element and a pre-concentrator agent for caffeine determination. The prepared electrode was used for caffeine measurement via a three-step procedure including analyte extraction in the electrode, electrode washing and electrochemical measurement of caffeine. The MIP-CP electrode showed very high recognition ability in comparison to NIP-CP. It was shown that electrode washing after caffeine extraction led to enhanced selectivity. Differential pulse voltammetry for caffeine determination was more effective than square wave voltammetry. Some parameters affecting sensor response were optimized, and a calibration curve was then plotted. A linear range of 6 × 10⁻⁸ to 2.5 × 10⁻⁵ mol L⁻¹ was obtained. The detection limit of the sensor was calculated to be equal to 1.5 × 10⁻⁸ mol L⁻¹. This sensor was used successfully for caffeine determination in spiked beverage and tea samples.     

Electrochemical study on cobalt film modified glassy carbon electrode and its application

A novel electroactive material for ascorbic acid (AA) determination was successfully prepared by plating/potential cycling method. The cobalt film was first deposited on the surface of glassy carbon electrode (GCE) in CoSO₄ solution by potential cycling, and then a cobalt film on the surface of GCE was activated by potential cycling in 0.1 mol L⁻¹ NaOH. The electrochemical performance of the resulted film (Co/GCE) and factors affecting its electrochemical activity were investigated by cyclic voltammetry and amperometry. This film electrode exhibited good electrocatalytic activity to the oxidation of AA. This biosensor had a fast response of AA less than 3 s and excellent linear relationships were obtained in the concentration range of 3 × 10⁻⁷ to 1 × 10⁻⁴ mol L⁻¹ with a detection limit of 2 × 10⁻⁷ mol L⁻¹ (S/N = 3) under the optimum conditions. Moreover, the selectivity, stability and reproducibility of this biosensor were evaluated with satisfactory results.     

Electrocatalytic oxidation and simultaneous determination of uric acid and ascorbic acid on the gold nanoparticles-modified glassy carbon electrode

A new gold nanoparticles-modified electrode (GNP/LC/GCE) was fabricated by self-assembling gold nanoparticles to the surface of the l-cysteine-modified glassy carbon electrode. The modified electrode showed an excellent character for electrocatalytic oxidization of uric acid (UA) and ascorbic acid (AA) with a 0.306 V separation of both peaks, while the bare GC electrode only gave an overlapped and broad oxidation peak. The anodic currents of UA and AA on the modified electrode were 6- and 2.5-fold to that of the bare GCE, respectively. Using differential pulse voltammetry (DPV), a highly selective and simultaneous determination of UA and AA has been explored at the modified electrode. DPV peak currents of UA and AA increased linearly with their concentration at the range of 6.0 × 10⁻⁷ to 8.5 × 10⁻⁴ mol L⁻¹ and 8.0 × 10⁻⁶ to 5.5 × 10⁻³ mol L⁻¹, respectively. The proposed method was applied for the detection of UA and AA in human urine with satisfactory result.     

Structural and electrochemical characterization of a cobalt phthalocyanine bulk-modified SiO2/SnO2 carbon ceramic electrode

A cobalt phthalocyanine bulk-modified carbon ceramic composite has been prepared by using sol-gel processing, and characterized by BET surface area, X-ray photoelectron spectroscopy, scanning electron microscopy and atomic force microscopy. A water-soluble 3-n-propylpyridinium chloride silsesquioxane (SiPyCl), an ion exchanger polymer, was employed to attach cobalt(II) tetrasulfophthalocyanine (CoTsPc) and prevent its leakage, as well as, to ensure adequate dispersion in the sol-gel network. The modified electrode built in a rigid disk-format displayed good electrocatalytic behavior towards the oxidation of oxalic acid at 0.84 V (SCE), as evidenced by the enhancement of the anodic current peak intensity when the concentration of oxalic acid was increased. A linear response was found in the range of 1.6 × 10⁻⁵ to 1.5 × 10⁻³ mol l⁻¹ with a detection limit of 7.1 × 10⁻⁶ mol l⁻¹.     

The use of silver solid amalgam electrode for voltammetric and amperometric determination of nitroquinolines

Solid amalgam electrodes represent a suitable alternative to mercury electrodes due to their similar electrochemical properties and non-toxicity of the amalgam material. Nitro derivatives of quinoline have been proven to be genotoxic, thus their presence in environmental samples is a legitimate cause for concern.In this contribution, meniscus modified silver solid amalgam electrode (m-AgSAE) was employed for the batch voltammetric determination and amperometric determination in connection with flow injection analysis of 5-nitroquinoline and 6-nitroquinoline (5-NQ, 6-NQ). Their electrochemical behavior was characterized by cyclic voltammetry, for their determination direct current voltammetry and differential pulse voltammetry were used. Linear calibration curves in the concentration range of 2 × 10⁻⁷ to 1 × 10⁻⁴ mol L⁻¹ were obtained. These results are comparable with results obtained for polarographic determination of the same substances using mercury electrodes. Further, the meniscus modified silver solid amalgam electrode was employed in amperometric detection cell in “wall jet” arrangement for determination of 5-NQ in flow injection analysis. Under optimized conditions (run buffer 0.05 mol L⁻¹ borate buffer, pH 9.0; flow rate 4 mL min⁻¹; detection potential −1.6 V; injection volume 0.1 mL), the limit of quantitation of ∼4 × 10⁻⁶ mol L⁻¹ was achieved. The repeatability of the detector response is satisfactory (relative standard deviation ∼2.15% for c(5-NQ) = 1 × 10⁻⁴ mol L⁻¹). Practical applicability of the method was verified for the determination of micromolar concentrations of 5-NQ in drinking and river water model samples.     

Polyaniline Langmuir-Blodgett film modified glassy carbon electrode as a voltammetric sensor for determination of Ag ions

A highly sensitive electrochemical sensor made of a glassy carbon electrode (GCE) coated with a Langmuir-Blodgett film (LB) containing polyaniline (PAn) doped with p-toluenesulfonic acid (PTSA) (LB/PAn-PTSA/GCE) has been used for the detection of trace concentrations of Ag⁺. UV-vis absorption spectra indicated that the PAn was doped by PTSA. The surface morphology of the PAn LB film was characterized by atomic force microscopy (AFM). The electrochemical properties of this LB/PAn-PTSA/GCE were studied using electrochemical impedance spectroscopy (EIS) and cyclic voltammetry. The LB/PAn-PTSA/GCE was used as a voltammetric sensor for determination of trace Ag⁺ at pH 5.0 using linear scanning stripping voltammetry. Under the optimal experimental conditions, the stripping current was proportional to the Ag⁺ concentration over the range from 6.0 × 10⁻¹⁰ mol L⁻¹ to 1.0 × 10⁻⁶ mol L⁻¹, with a detection limit of 4.0 × 10⁻¹⁰ mol L⁻¹. The high sensitivity, selectivity, and stability of this LB/PAn-PTSA/GCE also demonstrated its practical utility for simple, rapid and economical determination of Ag⁺ in water samples.     

Study of the potentiometric response of the doped spinel Li1.05Al0.02Mn1.98O4 for the optimization of a selective lithium ion sensor

In this paper, we studied the development of a selective lithium ion sensor constituted of a carbon paste electrode modified (CPEM) with an aluminum-doped spinel-type manganese oxide (Li_1.05Al_0.02Mn_1.98O₄) for investigating the influence of a doping ion in the sensor response. Experimental parameters, such as influence of the lithium concentration in the activation of the sensor by cyclic voltammetry, pH of the carrier solution and selectivity for Li⁺ against other alkali and alkaline-earth ions were investigated. The sensor response to lithium ions was linear in the concentration range 5.62 × 10⁻⁵ to 1.62 × 10⁻³ mol L⁻¹ with a slope 100.1 mV/decade over a wide pH 10 (Tris buffer) and detection limit of 2.75 × 10⁻⁵ mol L⁻¹, without interference of other alkali and alkaline-earth metals, demonstrating that the Al³⁺ doping increases the structure stability and improves the potentiometric response and sensitivity of the sensor. The super-Nernstian response of the sensor in pH 10 can be explained by mixed potential arising from two equilibria (redox and ion-exchange) in the spinel-type manganese oxide.     

An electrochemiluminescent biosensor for vitamin C based on inhibition of luminol electrochemiluminescence on graphite/poly(methylmethacrylate) composite electrode

A novel graphite/poly(methyl methacrylate) (graphite/PMMA) electrode was prepared in this paper. It was found that the developed polymer graphite paste electrode has some advantages in electrochemistry and electrochemiluminescence (ECL), such as high sensitivity, good reproducibility, quick and wide linear range of response to some biomolecules. The ECL behavior of luminol has been investigated in detail at the graphite/PMMA electrode, and vitamin C was found to be able to inhibit this ECL system. Based on which an inhibited ECL detection method has been developed for determination of vitamin C in this paper. The proposed method exhibited good reproducibility, wide-range linearity, high sensitivity and stability with a detection limit of 8.3 × 10⁻⁹ mol L⁻¹ (signal-to-noise ratio = 3) and linear response range of 2.5 × 10⁻⁸-1.0 × 10⁻⁴ mol L⁻¹. The relative standard deviation was 2.3% for 5 × 10⁻⁶ mol L⁻¹ vitamin C (n = 9). The possible mechanism for inhibition of luminol on graphite/PMMA electrode has also been proposed.     

Facile electrosynthesis of nitro-group-substituted oligopyrene with bicolored emission

Nitro-group-substituted oligopyrene (ONP) film with fairly high electrical conductivity (1.25 × 10⁻¹ S cm⁻¹) and good thermal stability was electrochemically synthesized by direct anodic oxidation of its monomer 1-nitropyrene (NP) in boron trifluoride diethyl etherate (BFEE). The oxidation potential of NP in this medium was determined to be 1.12 V vs. SCE, which was lower than that in acetonitrile +0.1 mol L⁻¹ Bu₄NBF₄ (1.27 V vs. SCE). ONP films obtained from this medium showed good redox activity and structural stability in both BFEE and concentrated sulfuric acid. Fourier transform infrared spectra and theoretical calculations showed that the electropolymerization of the NP monomer mainly occurred at the C(3), C(6) and C(8) positions. The fluorescence spectra suggested that soluble ONP emits strong blue or green fluorescence when excited at 402 nm or 504 nm, respectively. Scanning electron microscopy showed that highly crystalline nitro-group-substituted oligopyrene was formed on the electrode surface. All these results indicate that as-prepared ONP film has many potential applications in various fields.     

Direct electrochemistry of guanosine on multi-walled carbon nanotubes modified carbon ionic liquid electrode

A multi-walled carbon nanotubes (MWCNTs) modified carbon ionic liquid electrode (CILE) was fabricated and used to investigate the electrochemical behavior of guanosine. CILE was prepared by mixing hydrophilic ionic liquid 1-ethyl-3-methylimidazolium tetrafluoroborate (EMIMBF₄), graphite powder and liquid paraffin together. The fabricated MWCNTs/CILE showed great electrocatalytic ability to the oxidation of guanosine and an irreversible oxidation peak appeared at 1.067 V (vs. SCE) with improved peak current. The electrochemical behavior of guanosine on the MWCNTs/CILE was carefully studied by cyclic voltammetry and the electrochemical parameters such as the charge transfer coefficient (α) and the electrode reaction standard rate constant (k_s) were calculated with the result as 0.66 and 2.94 × 10⁻⁴ s⁻¹, respectively. By using differential pulse voltammetry (DPV) as the detection method, a linear relationship was obtained between the oxidation peak current and the guanosine concentration in the range from 1.0 × 10⁻⁷ to 4.0 × 10⁻⁵ mol/L with the detection limit as 7.8 × 10⁻⁸ mol/L (3σ). The common coexisting substances showed no interferences to the guanosine detection and the modified electrode showed good ability to distinguish the electrochemical response of guanosine and adenosine.     

A simple electroanalytical method for the analysis of the dye solvent orange 7 in fuel ethanol

The purpose of this paper is to develop a simple, rapid and accurate electroanalytical method for the determination of solvent orange 7 (SO-7), commercially used as a dye marker in fuel ethanol samples. SO-7 is oxidized in a mixture of Britton-Robinson buffer with N,N-dimethylformamide (1:1, v/v) at a glassy carbon electrode and presents a well-defined peak around +0.70 V vs. Ag/AgCl, which can be monitored by linear-scan voltammetry (LSV) and square-wave voltammetry (SWV). Using optimized parameters based on the SWV technique, it is possible to get a linear relationship between the peak current and the SO-7 dye concentration from 4.0 × 10⁻⁶ to 18.0 × 10⁻⁶ mol L⁻¹ (r = 0.995). The proposed method was successfully applied to the direct quantification of the SO-7 dye in fuel ethanol samples, which gave good average recovery for commercial samples containing 5.0 mg L⁻¹ and 10.0 mg L⁻¹ of SO-7 dye, respectively.     

An electrochemical biosensor based on Nafion-ionic liquid and a myoglobin-modified carbon paste electrode

An electrochemical biosensor was constructed based on the immobilization of myoglobin (Mb) in a composite film of Nafion and hydrophobic ionic liquid 1-butyl-3-methylimidazolium hexafluorophosphate (BMIMPF₆) for a modified carbon paste electrode (CPE). Direct electrochemistry of Mb in the Nafion-BMIMPF₆/CPE was achieved, confirmed by the appearance of a pair of well-defined redox peaks. The results indicate that Nafion-BMIMPF₆ composite film provided a suitable microenvironment to realize direct electron transfer between Mb and the electrode. The cathodic and anodic peak potentials were located at −0.351 V and −0.263 V (vs. SCE), with the apparent formal potential (Ep) of −0.307 V, which was characteristic of Mb Fe(III)/Fe(II) redox couples. The electrochemical behavior of Mb in the composite film was a surface-controlled quasi-reversible electrode process with one electron transfer and one proton transportation when the scan rate was smaller than 200 mV/s. Mb-modified electrode showed excellent electrocatalytic activity towards the reduction of trichloroacetic acid (TCA) in a linear concentration range from 2.0 × 10⁻⁴ mol/L to 1.1 × 10⁻² mol/L and with a detection limit of 1.6 × 10⁻⁵ mol/L (3σ). The proposed method would be valuable for the construction of a third-generation biosensor with cheap reagents and a simple procedure.     

Effects of NO2 ions on localised corrosion of steel in NaHCO3 + NaCl electrolytes

Pitting corrosion of carbon steel electrodes in 0.1 mol L⁻¹ NaHCO₃ + 0.02 mol L⁻¹ NaCl solutions was induced by anodic polarisation. The evolution of the breakdown potential E_b with NO₂⁻ concentration was investigated by linear voltammetry. E_b increased from −15 ± 5 mV/SCE for [NO₂⁻] = 0 up to 400 ± 50 mV/SCE for [NO₂⁻] = 0.1 mol L⁻¹. During anodic polarisation at potentials comprised between E_b([NO₂⁻] = 0) and E_b([NO₂⁻] ≠ 0), the behaviour of the whole electrode surface, followed by chronoamperometry, was compared to the behaviour of one single pit, followed via scanning vibrating electrode technique (SVET). Addition of a NaNO₂ solution after the beginning of the polarisation led to a rapid repassivation of pre-existing well-grown pits. In situ micro-Raman spectroscopy was then used to identify the corrosion products forming inside the pits. The first species to be detected in the presence of NO₂⁻ were mainly dissolved Fe(III) species, more likely [Fe^III(H₂O)₆]³⁺ complexes. Iron(II) carbonate FeCO₃, siderite, and carbonated green rust GR(CO₃²⁻) were also detected in the active pits, as in the absence of nitrite. But they were accompanied by maghemite γ-Fe₂O₃, a phase structurally similar to the passive film, that forms from the Fe(III) complexes. The Raman analyses then correlate with the SVET observations and confirm that the main effect of nitrite ions is to oxidize iron(II) into iron(III). The passive film would then form from the Fe(III) species still bound to the steel surface.     

Catalytic adsorptive stripping voltammetric determination of Cr(VI) in EDTA extracts from solid samples

A catalytic adsorptive stripping voltammetric procedure which allows for Cr(VI) determination in EDTA extracts is presented. EDTA used for extraction can be exploited as a masking agent for Cr(III). The calibration graph for Cr(VI) for an accumulation time of 60 s was linear in the range from 2 × 10⁻¹⁰ to 3 × 10⁻⁸ mol L⁻¹. The relative standard deviation for a Cr(VI) concentration of 2 × 10⁻⁹ mol L⁻¹ was 5.1% (n = 5). The detection limit estimated from three times the standard deviation of low Cr(VI) concentration and accumulation time of 60 s was about 7 × 10⁻¹¹ mol L⁻¹. The influence of foreign ions commonly present in extracts from solid samples is presented. The proposed voltammetric procedure was applied to determine Cr(VI) in EDTA extractable chromium from soil certified reference materials CRM 483 and CRM 041. The performance of the method was also verified by studying the recovery of Cr(VI) from spiked river water.