Templated grain growth of SrBi2Ta2O9 ceramics: Mechanism of texture development

Textured SrBi₂Ta₂O₉ (SBT) ceramics were fabricated via templated grain growth (TGG) technique using platelet-like SBT single crystal templates. The templates (5 wt%) were embedded in a fine-grain SBT powder matrix containing 3 wt% of Bi₂O₃ excess that were subjected to uniaxial pressing and sintering at 1000–1250 °C for up to 24 h. Microstructural characterization by SEM was performed to establish the effect of sintering parameters on the grain growth and texture development. It was found that the ceramics developed a bimodal microstructure with notable concentration of large (longer than 90 μm) aligned grains with c-axis oriented parallel to the pressing direction. The mechanism controlling the texture development and grain growth in SBT ceramics is discussed.     

Crystal structure and spectroscopic studies of NaGd(PO3)4

Single crystals of gadolinium–sodium polyphosphate NaGd(PO₃)₄ were grown for the first time using a flux method and characterized by X-ray diffraction. This phosphate crystallizes in a monoclinic system with P2₁/n space group and with the following unit-cell dimensions: a = 9.767(3) Å, b = 13.017(1) Å, c = 7.160(2) Å, β = 90.564(5)°, V = 910.3(4) Å³ and Z = 4. The crystal structure was solved from 3451 X-ray independent reflections with final R(F²) = 0.0219 and R_w(F²) = 0.056 refined with 164 parameters (). The atomic arrangement can be described as a long chain polyphosphate organization. Two infinite (PO₃)∝ chains with a period of eight tetrahedra run along the [0 1 1] direction. The structure of NaGd(PO₃)₄ consists of GdO₈ polyhedra sharing oxygen atoms with phosphoric group PO₄. Each Na⁺ ion is bonded to eight oxygen atoms.     

Microwave dielectric properties and microstructures of MgTa2O6 ceramics with CuO addition

The effect of CuO addition on the microstructures and the microwave dielectric properties of MgTa₂O₆ ceramics has been investigated. It is found that low level-doping of CuO (up to 1 wt.%) can significantly improve the density of the specimens and their microwave dielectric properties. Tremendous sintering temperature reduction can be achieved due to the liquid phase effect of CuO addition observed by scanning electronic microscopy (SEM). The sintered samples exhibit excellent microwave dielectric properties, which depend upon the liquid phase and the sintering temperature. With 0.5 wt.% CuO addition, MgTa₂O₆ ceramic can be sintered at 1400 °C and possesses a dielectric constant (_r) of 28, a Q × f value of 58000 GHz and a temperature coefficient of resonant frequency (τ_f) of 18 ppm/°C.     

Deposition of Sm2O3 doped CeO2 thin films from Ce(DPM)4 and Sm(DPM)3 (DPM=2,2,6,6-tetramethyl-3,5-heptanedionato) by aerosol-assisted metal–organic chemical vapor deposition

Samarium-doped ceria (SDC) thin films were prepared from Sm(DPM)₃ (DPM = 2,2,6,6-tetramethyl-3,5-heptanedionato) and Ce(DPM)₄ using the aerosol-assisted metal–organic chemical vapor deposition method. -Al₂O₃ and NiO-YSZ (YSZ = Y₂O₃-stabilized ZrO₂) disks were chosen as substrates in order to investigate the difference in the growth process on the two substrates. Single cubic structure could be obtained on either -Al₂O₃ or NiO-YSZ substrates at deposition temperatures above 450 °C; the similar structure between YSZ and SDC results in matching growth compared with the deposition on -Al₂O₃ substrate. A typical columnar structure could be obtained at 650 °C on -Al₂O₃ substrate and a more uniform surface was produced on NiO-YSZ substrate at 500 °C. The composition of SDC film deposited at 450 °C is close to that of precursor solution (Sm : Ce = 1 : 4), higher or lower deposition temperature will both lead to sharp deviation from this elemental ratio. The different thermal properties of Sm(DPM)₃ and Ce(DPM)₄ may be the key reason for the variation in composition with the increase of deposition temperature.     

Crystal structure and characterization of [2,5-(CH3O)2C6H3NH3]4P4O12·2H2O

The preparation, crystal structure, TG–DTA analysis and spectroscopy investigation are reported for the 2,5-dimethoxy phenyl ammonium cyclotetraphosphate dihydrate [2,5-(CH₃O)₂C₆H₃NH₃]₄P₄O₁₂·2H₂O. This new compound is triclinic P with unit cell dimensions: a = 7.438(5) Å, b = 11.841(7) Å, c = 12.354(4) Å,  = 96.61(4)°, β = 98.35(4)°, γ = 102.60(6)°, Z = 1 and V = 1038.0(1) Å³. Its crystal structure has been determined and refined to R = 0.049, with 5128 independant reflections. The structure can be described by rows of P₄O₁₂ ring anions along the a axis; between these rows are located the organic groups, connected to them by hydrogen bonds.     

Fibrous monoliths of mullite-AlPO4 and alumina/YAG-alumina platelets

Two-layer, fibrous monolithic composites consisting of mullite-aluminum phosphate (AlPO₄) and 50 vol.% alumina:50 vol.% YAG in situ composite matrix–alumina platelet interphase components, were fabricated by a co-extrusion technique. The four powders were characterized for particle size, specific surface area, and SEM analysis. The mixing formulations for extruding the powders were developed using ethylene vinylacetate copolymer as a binder. The variation in the mixing torque, in a Brabender mixer, as a function of temperature was measured. The binder removal behavior of the mullite-AlPO₄ fibrous monolithic composite was studied by thermogravimetric analysis (TGA). The AlPO₄ and alumina platelet interphase layers formed a porous and less porous interphase region, respectively, after sintering. The sintered mullite-AlPO₄ two-layer fibrous monolithic showed non-brittle fracture behavior. Its 3-point bend strength and work of fracture were 76 ± 5 MPa and 0.45 ± 0.02 kJ/m², respectively.     

Synthesis of (Bi0.5Na0.5)TiO3 nanocrystalline powders by stearic acid gel method

Bismuth sodium titanate (Na_0.5Bi_0.5)TiO₃ (NBT), is considered to be an excellent candidate for a key material of lead-free piezoelectric ceramics. In this study, we propose a stearic acid gel method for the preparation of nanocrystalline single phase NBT powder at relatively low treatment-temperature. Infrared (IR) spectroscopy, differential thermal analysis (DTA), thermogravimetric analysis (TG) and X-ray diffraction (XRD) were used to characterize the process of crystallization. The particle size and morphology of the calcined powders were examined by TEM. It shows that pure single phase NBT powders could be obtained at 700 °C for 1 h, and the particle size is about 20 nm. With an increase in the calcination temperature, crystallite size increased. The powders were further pressed into disk and sintered at 1120 °C for 2 h in air, and its density and microstructure were compared with traditionally prepared samples.     

Processing, microstructure and properties of C40 Mo(Si,Al)2/Al2O3 composites

The C40 Mo(Si_0.75Al_0.25)₂/Al₂O₃ composites were prepared by spark plasma sintering (SPS) of mechanically alloyed (MA) powders. The Mo(Si_0.75Al_0.25)₂/0–20 vol.% Al₂O₃ materials, showing micron and submicron composite structure, possess a hardness of 13.9–14.6 GPa but a poor toughness of 1.78–1.80 MPa m^1/2. The addition of 30 vol.% Al₂O₃ leads to the formation of the micron C40 Mo(Si_0.75Al_0.25)₂/Al₂O₃ composite with an intergranular distribution of Al₂O₃, that results in a drop of the hardness to 10.2 GPa and an improvement of the toughness to 3.67 MPa m^1/2. The transition of the cleavage facets to the intergranular fracture with the addition of Al₂O₃ is assumed as the main toughening mechanism.     

Densification and grain growth during pressureless sintering of TiO2 nanoceramics

Anatase titania nanopowders with mean particle sizes of 7, 15, 26 and 38 nm synthesized by sol–gel method were used to sinter bulk TiO₂ nanoceramics. The relative densities and average grain sizes of the TiO₂ nanoceramics were studied as a function of the compaction pressure on green sheet, sintering temperature, and mean particle size of the starting TiO₂ nanopowders. The relative density of the TiO₂ nanoceramics increases rapidly and average grain size increases slowly with increasing sintering temperature below 800 °C. Sintering at higher temperatures above 800 °C enhances the densification of the TiO₂ nanoceramics and leads to a increase of the grain size. Bulk TiO₂ nanoceramics with an average grain size of less than 60 nm and relative density over 95% was obtained by a phase-transformation-assisted pressureless sintering at a relatively low temperature (800 °C).     

Effect of CeO2 addition on structure and electrical properties of (Na0.5Bi0.5)0.93Ba0.07TiO3 ceramics prepared by citric method

(Na_0.5Bi_0.5)_0.93Ba_0.07TiO₃ ceramics added with 0–0.8 wt.% CeO₂ were prepared by a citrate method, and the influence of the CeO₂ addition on the structure and electrical properties was investigated. The specimens containing various amounts of CeO₂ show the coexistence of rhombohedral and tetragonal phases, with the relative content of the tetragonal phases gradually enhancing with increasing amount of CeO₂. Compared with (Na_0.5Bi_0.5)_0.93Ba_0.07TiO₃, the specimen added with a small amount of CeO₂ (≤0.2 wt.%) display a slightly improved electromechanical coupling factor (k_p) and piezoelectric constant (d₃₃) in conjunction with a reduced dielectric loss (tg δ) and an enhanced mechanical quality factor (Q_m), while higher CeO₂ amounts led to a rapid deterioration of the piezoelectric and ferroelectric properties. The variation of the electrical properties with the CeO₂ addition was tentatively interpreted with respect to doping effect, crystal-structural evolution and stability of ferroelectric domains.     

Vacuum heat treatment of LiAlO2 densified silicon nitride ceramics

The aim of the present work has been to produce high-dense Si₃N₄ ceramics by a cheaper pressureless sintering method and then to attain vacuum heat treatment to remove residual grain boundary glass in gaseous form. LiAlO₂ was used as a sintering additive rather than using Li₂O, since its grain boundary glass is not stable above 1200 °C. LiAlO₂ was synthesised from 42% Li₂CO₃ and 58% Al₂O₃ powder mix reacting together at 1450 °C for 3 h in a muffle furnace. X-ray analysis showed that 95% LiAlO₂ was obtained. LiAlO₂ was milled and added to silicon nitride powder as a sintering additive. Hot-pressing and pressureless sintering of LiAlO₂ containing Si₃N₄ compacts were carried out at temperatures between 1450–1750 °C. The sintered samples were vacuum heat-treated at elevated temperatures under high vacuum to remove intergranular glass and to increase refractoriness of Si₃N₄ ceramics. Scanning electron microscope images and weight loss results showed that Li in grain boundary glass (Li–Al–Si–O–N) was successfully volatilised, and oxidation resistance of the sintered samples was increased.     

Influence of Mn doping on microstructure and DC-accelerated aging behaviors of ZnO–V2O5-based varistors

The microstructure, electrical properties, dielectric characteristics, and DC-accelerated aging behavior of the ZnO–V₂O₅–MnO₂ system sintered were investigated for MnO₂ content of 0.0–2.0 mol% by sintering at 900 °C. For all samples, the microstructure of the ZnO–V₂O₅–MnO₂ system consisted of mainly ZnO grain and secondary phase Zn₃(VO₄)₂. The incorporation of MnO₂ to the ZnO–V₂O₅ system was found to restrict the abnormal grain growth of ZnO. The nonlinear properties and stability against DC-accelerated aging stress improved with the increase of MnO₂ content. The ZnO–V₂O₅–MnO₂ system added with MnO₂ content of 2.0 mol% exhibited not only a high nonlinearity, in which the nonlinear coefficient is 27.2 and the leakage current density is 0.17 mA/cm², but also a good stability, in which %ΔE_1 mA = −0.6%, %Δ = −26.1%, and %Δtan δ = +22% for DC-accelerated aging stress of 0.85E_1 mA/85 °C/24 h.     

Synthesis, structure refinement and characterization of tetrahydrated acid gadolinium diphosphate HGdP2O7·4H2O

Synthesis and single crystal structure are reported for a new gadolinium acid diphosphate tetrahydrate HGdP₂O₇·4H₂O. This salt crystallizes in the monoclinic system, space group P2₁/n, with the following unit-cell parameters: a = 6.6137(2) Å, b = 11.4954(4) Å, c = 11.377(4) Å, β = 87.53(2)° and Z = 4. Its crystal structure was refined to R = 0.0333 using 1783 reflections. The corresponding atomic arrangement can be described as an alternation of corrugated layers of monohydrogendiphosphate groups and GdO₈ polyhedra parallel to the () plane. The cohesion between the different diphosphoric groups is provided by strong hydrogen bonding involving the W4 water molecule.

IR and Raman spectra of HGdP₂O₇·4H₂O confirm the existence of the characteristic bands of diphosphate group in 980–700 cm⁻¹ area. The IR spectrum reveals also the characteristic bands of water molecules vibration (3600–3230 cm⁻¹) and acidic hydrogen ones (2340 cm⁻¹). TG and DTA investigations show that the dehydration of this salt occurs between 79 and 900 °C. It decomposes after dehydration into an amorphous phase. Gadolinium diphosphate Gd₄(P₂O₇)₃ was obtained by heating HGdP₂O₇·4H₂O in a static air furnace at 850 °C for 48 h.     

Piezoelectric and dielectric properties of PZT–PZN–PMS ceramics prepared by molten salt synthesis method

Piezoelectric powders and ceramics with the composition of Pb_0.95Sr_0.05(Zr_0.52Ti_0.48)O₃–Pb(Zn_1/3Nb_2/3)O₃–Pb(Mn_1/3Sb_2/3)O₃ (PZT–PZN–PMS) were prepared by molten salt synthesis (MSS) and conventional mixed-oxide (CMO) methods, respectively. The influence of synthesis process on the properties of powders and ceramics were investigated in detail. The results show that the MSS method significantly improved the sinterability of PZT–PZN–PMS ceramics, resulting in an improvement of dielectric and piezoelectric properties compared to the CMO method. The optimum values of MSS samples are as follows: _r = 1773; tan δ = 0.0040; T_c = 280 °C; d₃₃ = 455 pC/N; k_p = 0.70; Q_m = 888; E_c = 10.3 kV/cm; and P_r = 28.2 μC/cm², at calcination of 800 °C and sintering of 1120 °C temperature.     

Improvements in mechanical properties of TiB2 ceramics tool materials by the dispersion of Al2O3 particles

TiB₂–Al₂O₃ composites with Ni–Mo as sintering aid have been fabricated by a hot-press technique at a lower temperature of 1530 °C for 1 h, and the mechanical properties and microstructure were investigated. The microstructure consists of dispersed Al₂O₃ particles in a fine-grained TiB₂ matrix. The addition of Al₂O₃ increases the fracture toughness up to 6.02 MPa m^1/2 at an amount of 40 vol.% Al₂O₃ and the flexural strength up to 913.86 MPa at an amount of 10 vol.% Al₂O₃. The improved flexural strength of the composites is a result of higher density than that of monolithic TiB₂. The increase of fracture toughness is a result of crack bridging by the metal grains on the boundaries, and crack deflection by weak grain boundaries due to the bad wetting characters between Ni–Mo and Al₂O₃.     

Kinetic analysis on Al2O3/Cu composite prepared by mechanical activation and internal oxidation

The Al₂O₃/Cu composite was prepared by mechanical activation and internal oxidation process. Kinetic factors, which influenced the internal oxidation process, were also discussed in the present paper. The results showed that the duration of the internal oxidation was highly shortened after the powders were treated by mechanical activation. The typical internal oxidation duration was only 1 h. It is unnecessary for further prolonging internal oxidation time. Besides, in order to get a complete internal oxidation heating rate and green density of the compact are another two control factors. Their parameters should be controlled from Al contents in the powders. In this research, the optimum internal oxidation duration, heating rate and green density are 1 h, 20 °C/min and 80%, respectively, for Cu–0.8 wt% Al/Cu₂O powders. After the internal oxidation, uniform spherical -Al₂O₃ particles with an average size 0.5–0.8 μm in diameter were observed in the Cu matrix.     

Direct liquid injection metal-organic chemical vapor deposition of HfO2 thin films using Hf(dimethylaminoethoxide)4

Hf(OCH₂CH₂NMe₂)₄, [Hf(dmae)₄] (dmae=dimethylaminoethoxide) was synthesized and used as a chemical vapor deposition precursor for depositing Hf oxide (HfO₂). Hf(dmae)₄ is a liquid at room temperature and has a moderate vapor pressure (4.5 Torr at 80 °C). It was found that HfO₂ film could be deposited as low as 150 °C with carbon level not detected by X-ray photoelectron spectroscopy. As deposited film was amorphous but when the deposition temperature was raised to 400 °C, X-ray diffraction pattern showed that the film was polycrystalline with weak peak of monoclinic (020). Scanning electron microscope analysis indicated that the grain size was not significantly changed with the increase of the annealing temperature. Capacitance–voltage measurement showed that with the increase of annealing temperature, the effective dielectric constant was increased, but above 900 °C, the effective dielectric constant was decreased due to the formation of interface oxide. For 500 Å thin film, the dielectric constant of HfO₂ film annealed at 800 °C was 20.1 and the current–voltage measurements showed that the leakage current density of the HfO₂ thin film annealed at 800 °C was 2.2×10⁻⁶ A/cm² at 5 V.     

Novel soft solution synthesis and characterization of submicromic LiCoVO4

A novel soft solution process has been used to prepare LiCoVO₄ by reacting Co(CH₃CH₂COO)₂, Li₂CO₃, NH₄VO₃ and citric acid. LiCoVO₄ powders were successfully prepared at as low as 450 °C in 4 h. Compared to the solid-state reaction processes, the soft solution process greatly reduced the temperature and the time for preparing LiCoVO₄. The inverse spinel structure and high crystallinity of the synthesized product has been confirmed by X-ray diffraction. Thermal analysis proves that the phase formation of the compound occurs at about 450 °C. The results of the IR investigations show that the band located at 820 cm⁻¹ corresponds to the stretching vibration mode of VO₄ tetrahedron with the A symmetry. SEM examination reveals a spherical grain distribution, the average particle size being typically lower than 1 μm. The quantitative result from ICP-AES analysis is Li_0.967Co_0.994VO₄.     

Densification and Grain-Growth Behavior of Various Amounts of SiO2 Doped 8YSCZ/SiO2 Composites

The effect of SiO₂ addition on densification and grain-growth behavior of 8YSCZ/SiO₂ composites was investigated using high purity 8 mol% yttria-stabilized cubic zirconia powders (8YSCZ) doped with 0, 1, 5, 10 wt% SiO₂. The specimens were sintered at 1400°C for 1 hour. It was seen that the sintered density increased with SiO₂ content up to 1 wt% and further increase in SiO₂ content led to a decrease in density. The enhanced density with increasing SiO₂ content up to 1 wt% could be mainly attributable to liquid phase sintering. For grain growth measurements, the specimens sintered at 1400°C were annealed at 1400, 1500, and 1600°C for 10, 50, and 100 hours. The experimental results showed that the grain growth in 8YSCZ/SiO₂ composites occurred more slowly than that in undoped 8YSCZ. Also, the grain growth rate decreased with increasing SiO₂ content. The grain growth exponent value and the activation energy for undoped 8YSCZ were found to be 2 and 289 kJ/mol, respectively. The addition of SiO₂ raised the grain growth exponent value to 3, and activation energy for the grain growth process was increased from 289 to 420 kJ/mol for the addition of SiO₂ from 0 to 10 wt%.     

粉末冶金(FeNiMnAl_(x))_(50)Cu_(50)中熵合金的微观组织与力学性能EI北大核心CSCD

对物理法制备的再生铜合金粉末进一步合金化,通过机械合金化(MA)结合放电等离子烧结(SPS)的方法制备了(Fe_(40)Ni_(40)Mn_(20))_(50)Cu_(50),(Fe_(38)Ni_(38)Ni_(38)Mn_(19)Al_(5))_(50)Cu_(50),(Fe_(36)Ni_(36)Mn_(18)Al_(10))50 Cu_(50)和(Fe_(32)Ni_(32)Mn_(16)Al_(20))_(50)Cu_(50)四种中熵合金块体,并研究了Al元素的含量对中熵合金微观组织与力学性能的影响。结果表明:在高能球磨60 h之后合金粉末完成合金化,四种中熵合金粉末均形成单一FCC相的过饱和固溶体且有微量WC杂质。经SPS烧结后,(Fe_(40)Ni_(40)Mn_(20))_(50)Cu_(50),(Fe_(38)Ni_(38)Mn_(19)Al_(5))_(50)Cu_(50)和(Fe_(36)Ni_(36)Mn_(18)Al_(10))50 Cu_(50)形成了由富Cu的FCC1相和富Fe-Ni的FCC2相组成的双相FCC结构,并具有超细晶+微米晶的多尺度结构;而(Fe_(32)Ni_(32)Mn_(16)Al_(20))_(50)Cu_(50)由富Cu的FCC主相和少量富Fe-Mn的FCC2相及富Ni-Al的BCC相(B2)组成。随着Al含量的提高,四种中熵合金的塑性逐渐降低,而强度和硬度逐渐提高。(Fe_(40)Ni_(40)Mn_(20))_(50)Cu_(50)合金的压缩屈服强度、抗压强度和维氏硬度分别为878 MPa,1257 MPa和248.5HV。与(Fe_(40)Ni_(40)Mn_(20))_(50)Cu_(50)相比,(Fe_(32)Ni_(32)Mn_(16)Al_(20))_(50)Cu_(50)的压缩屈服强度和硬度分别提高了50.1%和50.4%,断裂应变由19.55%下降至8.31%。