Interface-controlled fatigue cracking of SCS-6/Ti-22Al-23Nb “orthorhombic” titanium aluminide composite

The effect of aging at elevated temperature on interfacial stability and fatigue behavior of a SCS-6/Ti-22Al-23Nb “orthorhombic” (O) titanium aluminide composite is investigated. The composite was heat treated in vacuum at 900 °C for up to 250 hours to change the microstructural characteristics. The stability of the matrix alloy and interfacial reaction zone after extended thermal exposure was analyzed. The effect of interface on fatigue behavior, including stiffness degradation, evolution of fatigue damage, and crack growth rates, was characterized. Finally, a modified shear-lag model was used to predict the saturated matrix crack spacing in the composite under fatigue loading. The results demonstrate that aging at elevated temperature affects the stability of the interfacial reaction zone, which, in turn, degrades the fatigue properties of the composite. However, fatigue crack will not develop from the ruptured interfacial reaction layer until the thickness of the reaction zone or the maximum applied stress exceeds a critical value.     

Frequency and wave-form effects on the fatigue crack growth behavior of alloy 718 at 298 K and 823 K

The fatigue crack growth rate (FCGR) of Alloy 718 was measured on CT type specimens at 298 and 823 K. At 823 K, the influence of frequency was studied in the range between 5 – 10^-3 Hz and 20 Hz, using a sinusoidal wave form signal. A substantial increase in FCGR occurred, particularly at low stress intensity levels, as the temperature was increased from 298 to 823 K and as the frequency was decreased at 823 K. At elevated temperature, the effect of cyclic stress wave form was equally investigated, using triangular and square wave form signals producing the same frequency of 5.10^-2 Hz. The triangular load led to higher FCGR than the square wave form. In addition the hold time of 10 s both at the maximum and the minimum load associated with the square load had no significant effect on the FCGR. Electron microscopy was used to observe the substructures that developed ahead of fatigue cracks. These observations showed that in certain circumstances plastic deformation proceeded by the propagation of planar bands which were identified as twins. At room temperature, twinning was found to be abundant only in the threshold regime. At 823 K, twinning was observed in the domain of higher FCGR, particularly at low frequencies. Fractography was carried out to study the micromechanisms of crack propagation. At 823 K. intergranular cracking occurred as the frequency was decreased. The comparison between the substructures formed in low cycle fatigue and those associated with the plastic zones of propagating cracks is made. The importance of planar deformation and twinning on intergranular cracking and on the acceleration of FCGR when the loading rate is decreased at 823 K, is discussed.     

GH4169合金高温疲劳裂纹扩展的微观损伤机制

空气环境对高温合金在高温下的损伤行为有显著影响.为了研究标准热处理态GH4169合金在高温疲劳裂纹扩展过程中的微观损伤机制,在空气环境中进行650℃、初始应力强度因子幅ΔK=30 MPa·m1/2和应力比R=0.05的低周疲劳裂纹扩展试验.使用扫描电镜(SEM)及能谱(EDS)对试样的断口、外表面和剖面进行观察和分析.实验结果表明:疲劳主裂纹以沿晶方式萌生并扩展,随后沿晶二次裂纹出现,并且其数量和长度沿主裂纹方向逐渐增加,进入快速扩展阶段后,断口呈现韧窝组织形貌;在裂纹扩展过程中,δ相与基体的界面发生氧化,使得沿晶二次裂纹沿界面扩展并产生偏折,从而起到阻碍二次裂纹扩展的作用;试样外表面的主裂纹周围出现晶界氧化损伤区,其尺寸和晶界开裂程度沿主裂纹扩展方向逐渐增大.      

Fracture Morphology and Local Deformation Characteristics in the Metallic Glass Matrix Composite Under Tension

Fracture and deformation characteristics of the Ti-based metallic glass matrix composite have been studied by the tensile test and the in situ TEM tension test. Typically, the composite exhibits the high strength and considerable plasticity. Microscopically, it was found that shear deformation zone formed at the crack tip in glass phase, which can bring about quick propagation of shear bands. However, the plastic deformation zone nearby the crack tip in dendrites will postpone or retard the crack extension by dislocations. The attributions of micro-deformations to mechanical properties of composites were discussed.     

Effect of interfacial debonding and sliding on matrix crack initiation during isothermal fatigue of SCS-6/Ti-15-3 composites

Direct observation of initial damage-evolution processes occurring during cyclic testing of an unnotched SCS-6 fiber-reinforced Ti-15-3 composite has been carried out. The aligned fibers break at an early stage, followed by debonding and subsequent sliding along the interface between the reaction layer (RL) and Ti-15-3 alloy matrix. Matrix cracking initiation from the initial broken fiber and RL was avoided. This fracture behavior during cyclic loading is modeled and analyzed by the finite-element method, with plastic deformation of the matrix being considered. The plastic strain in the matrix at the initial crack and at the deflected crack tips, when the interface crack is deflected into the RL after extensive interface debonding propagation, is characterized. The effects of interfacial debond lengths and test temperatures on the matrix cracking mechanism are discussed, based on a fatigue-damage summation rule under low-cycle fatigue conditions. The numerical results provide a rationale for experimental observations regarding the avoidance and occurrence of the matrix cracking found in fiber-reinforced titanium composites.     

Low cycle fatigue behavior of inconel 718 at 298 K and 823 K

The cyclic stress-strain response and the low cycle fatigue life of conventionally heat treated Inconel 718 were studied. Fully reversed strain-controlled tests were performed at room temperature and at 823 K. Optical and electron microscopy were used to study the development of deformation and cracking during cycling. A power-law relationship between life-time and plastic strain amplitude was obtained. A substantial decrease in fatigue life occurred as the temperature was increased from 298 to 823 K and as the cycling frequency was lowered from 3 cyclesJmin to 0.3 cyclesJmin at 823 K. At 298 K, for all the strain amplitudes investigated, an initial rapid hardening was followed by softening, while at 823 K only softening occurred. Electron microscopy showed that the precipitates were sheared in the course of cyclic straining and that plastic deformation proceeded by the propagation of planar bands. These bands were identified as twins. Twinning was found to be more abundant at elevated temperatures than at room temperature, especially at lower frequencies. Cracking was generally initiated along the interfaces between these twin bands and the matrix but, at elevated temperatures and low strain rates, intercrystalline cracking took place, as well. The influence of particles shearing and twinning on the cyclic stress-strain response of the material are discussed. The importance of planar deformation and twinning on intergranular cracking is emphasized. Formerly with Centre des Matériaux     

0.13C-5Mn中锰钢的裂纹扩展行为

 为了研究基体组织为铁素体和亚稳奥氏体的0.13C-5Mn中锰钢裂纹扩展特性,采用载荷控制对其进行裂纹扩展试验,采用SEM、EBSD等手段表征了裂纹扩展行为。研究结果表明,裂纹扩展机制为滑移和积累损伤双重机制。在裂纹尖端的塑性区内发生亚稳奥氏体转变为马氏体的相变,发生转变的区域远远小于裂纹尖端塑性区尺寸,由于相变吸收了能量以及裂纹闭合效应降低了疲劳裂纹扩展速率。     

一种单晶高温合金不同温度的高周疲劳性能

研究了一种单晶高温合金700 ℃和800 ℃的高周疲劳性能，采用扫描电镜和透射电镜分析了断口和断裂机制.结果表明，随着温度升高，合金的疲劳强度系数降低，Basquin系数增加，高周疲劳极限降低.合金700 ℃与800 ℃具有相同的高周疲劳断口，都有几个{111}面平面组成，为类解理断裂机制.疲劳断口由裂纹源区、扩展区和瞬断区3部分组成.裂纹起源于试样的表面或亚表面，并沿{111}面扩展.扩展区可见河流状花样、滑移带、疲劳弧线和疲劳条带特征.瞬断区可见解理台阶和撕裂棱.断裂后γ′相仍保持立方形状，位错不均匀分布在γ基体通道中.      

Monotonic and fatigue deformation of Ni-W directionally solidified eutectic

Unlike many eutectic composites, the Ni-W eutectic exhibits extensive ductility by slip. Furthermore, its properties may be greatly varied by proper heat treatments. Here results of studies of deformation in both monotonic and fatigue loading are reported. During monotonie deformation the fiber /matrix interface acts as a source of dislocations at low strains and an obstacle to matrix slip at higher strains. Deforming the quenched-plus-aged eutectic causes planar matrix slip, with the result that matrix slip bands create stress concentrations in the fibers at low strains. The aged eutectic reaches generally higher stress levels for comparable strains than does the as-quenched eutectic, and the failure strains decrease with increasing aging times. For the composites tested in fatigue, the aged eutectic has better high-stress fatigue resistance than the as-quenched material, but for low-stress, high-cycle fatigue their cycles to failure are nearly the same. However, both crack initiation and crack propagation are different in the two conditions, so the coincidence in high-cycle fatigue is probably fortuitous. The effect of matrix strength on composite performance is not simple, since changes in strength may be accompanied by alterations in slip modes and failure processes.     

Monotonic and fatigue deformation of Ni-W directionally solidified eutectic

Unlike many eutectic composites, the Ni-W eutectic exhibits extensive ductility by slip. Furthermore, its properties may be greatly varied by proper heat treatments. Here results of studies of deformation in both monotonic and fatigue loading are reported. During monotonie deformation the fiber /matrix interface acts as a source of dislocations at low strains and an obstacle to matrix slip at higher strains. Deforming the quenched-plus-aged eutectic causes planar matrix slip, with the result that matrix slip bands create stress concentrations in the fibers at low strains. The aged eutectic reaches generally higher stress levels for comparable strains than does the as-quenched eutectic, and the failure strains decrease with increasing aging times. For the composites tested in fatigue, the aged eutectic has better high-stress fatigue resistance than the as-quenched material, but for low-stress, high-cycle fatigue their cycles to failure are nearly the same. However, both crack initiation and crack propagation are different in the two conditions, so the coincidence in high-cycle fatigue is probably fortuitous. The effect of matrix strength on composite performance is not simple, since changes in strength may be accompanied by alterations in slip modes and failure processes.     

Fatigue crack growth of SM-1240/TIMETAL-21S metal matrix composites at elevated temperatures

A series of high-temperature fatigue crack growth experiments was conducted on a continuous-fiberreinforced SM1240/TIMETAL-21S composite using three different temperatures, room temperature (24 °C), 500 °C, and 650 °C, and three loading frequencies, 10, 0.1, and 0.02 Hz. In all the tests, the cracking process concentrated along a single mode I crack for which the principal damage mechanism was crack bridging and fiber/matrix debonding. The matrix transgranular fracture mode was not significantly influenced by temperature or loading frequency. The fiber debonding length in the crack bridging region was estimated based on the knowledge of the fiber pullout lengths measured along the fracture surfaces of the test specimens. The average pullout length was correlated with both temperature and loading frequency. Furthermore, the increase in the temperature was found to lead to a decrease in the crack growth rate. The mechanism responsible for this behavior is discussed in relation to the interaction of a number of temperature-dependent factors acting along the bridged fiber/matrix debonded zone. These factors include the frictional stress, the radial stress, and the debonding length of the fiber/matrix interface. In addition, the crack growth speed was found to depend proportionally on the loading frequency. This relationship, particularly at low frequencies, is interpreted in terms of the development of a crack tip closure induced by the relaxation of the compressive residual stresses developed in the matrix phase in regions ahead of the crack tip during the time-dependent loading process.     

Failure mechanisms in SiC-fiber reinforced 6061 aluminum alloy composites under monotonic and cyclic loading

Micromechanisms influencing crack propagation in a unidirectional SiC-fiber (SCS-8) continuously reinforced Al-Mg-Si 6061 alloy metal-matrix composite (SiC_f/Al-6061) during monotonie and cyclic loading are examined at room temperature, both for the longitudinal (0 deg or L-T) and transverse (90 deg or T-L) orientations. It is found that the composite is insensitive to the presence of notches in the L-T orientation under pure tension loading due to the weak fiber/matrix interface; notched failure strengths are ∼1500 MPa compared to 124 MPa for unreinforced 6061. However, behavior is strongly dependent on loading configuration, specimen geometry, and orientation. Specifically, properties in SiC_f/Al in the T-L orientation are inferior to unreinforced 6061, although the composite does exhibit increasing crack-growth resistance with crack extension (resistance-curve behavior) under monotonie loading; peak toughnesses of ∼16 MPa√m are achieved due to crack bridging by the continuous metal phase between fibers and residual plastic deformation in the crack wake. In contrast, such bridging is minimal under cyclic loading, as the ductile phase fails subcritically by fatigue such that the transverse fatigue crack-growth resistance is superior in the unreinforced alloy, particularly at high stress-intensity levels. Conversely, fatigue cracks are bridged by unbroken SiC fibers in the L-T orientation and exhibit marked crack deflection and branching; the fatigue crack-growth resistance in this orientation is clearly superior in the composite.     

The Significance of Crack Initiation Stage in Very High Cycle Fatigue of Steels

Different stages of the Very High Cycle Fatigue (VHCF) crack evolution in tool steels have been explored using a 20 kHz ultrasonic fatigue testing equipment. Extensive experimental data is presented describing VHCF behaviour, strength and crack initiating defects in an AISI H11 tool steel. Striation measurements are used to estimate fatigue crack growth rate, between 10^?8 and 10^?6 m/cycle, and the number of load cycles required for a crack to grow to critical dimensions. The growth of small fatigue cracks within the “fish‐eye” is shown to be distinctively different from the crack propagation behaviour of larger cracks. More importantly, the crack initiation stage is shown to determine the total fatigue life, which emphasizes the inherent difficulty to detect VHCF cracks prior to failure. Several mechanisms for initiation and early crack growth are possible. Some of them are discussed here: crack development by local accumulation of fatigue damage at the inclusion – matrix interface, hydrogen assisted crack growth and crack initiation by decohesion of carbides from the matrix.     

An assessment of cold work effects on strain-controlled low-cycle fatigue behavior of type 304 stainless steel

The influence of prior cold work (PCW) on low-cycle fatigue (LCF) behavior of type 304 stainless steel has been studied at 300, 823, 923, and 1023 K by conducting total axial strain-controlled tests in solution annealed (SA, 0 pct PCW) condition and on specimens having three levels of PCW, namely, 10, 20, and 30 pct. A triangular waveform with a constant frequency of 0.1 Hz was employed for all of the tests performed over strain amplitudes in the range of ±0.25 to ± 1.25 pct. These studies have revealed that fatigue life is strongly dependent on PCW, temperature, and strain amplitude employed in testing. The SA material generally displayed better endurance in terms of total and plastic strain amplitudes than the material in 10, 20, and 30 pct PCW conditions at all of the temperatures. However, at 300 K at very low strain amplitudes, PCW material exhibited better total strain fatigue resistance. At 823 K, LCF life decreased with increasing PCW, whereas at 923 K, 10 pct PCW displayed the lowest life. An improvement in life occurred for prior deformations exceeding 10 pct at all strain amplitudes at 923 K. Fatigue life showed a noticeable decrease with increasing temperature up to 1023 K in PCW state. On the other hand, SA material displayed a minimum in fatigue life at 923 K. The fatigue life results of SA as well as all of the PCW conditions obeyed the Basquin and Coffin-Manson relationships at 300, 823, and 923 K. The constants and exponents in these equations were found to depend on the test temperature and prior metallurgical state of the material. A study is made of cyclic stress-strain behavior in SA and PCW states and the relationship between the cyclic strain-hardening exponent and fatigue behavior at different temperatures has been explored. The influence of environment on fatigue crack initiation and propagation behavior has been examined.     

Use of the nanoindentation technique for studying microstructure/crack interactions in the fatigue of 4340 steel

The objectives of this research are to study the influence of microstructure on the fatigue crack growth behavior in 4340 steel and to explore the application of the nanoindentation technique for determining the plastic deformation zone at a fatigue crack tip. Two heat treatment conditions were chosen for the steel: annealed and quenched plus tempered. The annealed steel consists of coarse pearlite and proeutectoid ferrite, while the quenched and tempered steel consists of fine tempered martensite. Fatigue crack propagation tests were conducted on disklike compact (DCT) specimens. Subsequently, the nanoindentation technique was applied to quantitatively determine the plastic deformation zone at fatigue crack tips. The plastic deformation zone size determined by the nanoindentation test seems larger than the cyclic deformation zone calculated using the fracture mechanics equation, which involves many assumptions. The fatigue crack growth test results show that the annealed steel has a higher resistance to crack growth than the quenched and tempered steel. The fatigue crack in the annealed steel tends to grow along pearlite domain boundaries, or the cementite/ferrite interfaces within a pearlite domain. In contrast, the fatigue crack in the quenched and tempered steel tends to traverse the fine martensite laths. Consequently, the actual crack path in the annealed steel is rougher than in the quenched and tempered steel and more secondary cracks are observed in the annealed steel.     

The influence of SiC particulates on fatigue crack propagation in a rapidly solidified Al-Fe-V-Si alloy

The fatigue crack propagation properties of a rapidly solidified aluminum alloy are compared with those of a metal matrix composite (MMC) made of the same base alloy with the addition of 11.5 vol pct SiC particulate. The high-temperature base material, alloy 8009 produced by Allied-Signal, Inc. (Morristown, NJ), is solidified and processed using powder metallurgy techniques; these techniques yield a fine-grained, nonequilibrium microstructure. A direct comparison between the fatigue crack propagation properties of the reinforced and unreinforced materials is possible, because alloy 8009 requires no postprocessing heat treatment. As a consequence, this comparison reflects the influence of the SiC particulate and not differences in microstructure that could arise during processing and aging. The experimental data demonstrate that the SiC-reinforced material exhibits modestly superior fatigue crack propagation properties: slower crack growth rates for a given ΔK, at near-threshold crack growth rates. Even when the data are corrected for crack closure using an effective stress intensity factor, ΔK_eff, the composite exhibits lower crack propagation rates than the unreinforced matrix alloy. Microscopic evidence shows a rougher fracture surface and a more tortuous crack path in the composite than in the base alloy. It is argued that the lower crack growth rates and higher intrinsic threshold stress intensity factor observed in the composite are associated with crack deflection around SiC particles. Formerly Graduate Research Assistant, University of California-Davis     

Effect of Hot Deformation on Formation and Growth of Thermal Fatigue Crack in Chromium Wear Resistant Cast Iron

Chromium wear resistant cast iron is widelyusedin engineering, mining and power industry forits high strength,hardness and wear resistance .Inproduction process , some wear-resistant parts ser-ving in alternative stress due to rapid heating andcooling rate ofteninduces thermal fatigue andresultsinfailure .The badthermal fatigue property of chro-mium wear resistant cast iron is due to eutectic car-bides which distribute as continuous net in matrix.Recent researches showthat hot deformation can …     

Ultrasonic Fatigue Damage Behavior of 304L Austenitic Stainless Steel Based on Micro-plasticity and Heat Dissipation

Very high cycle fatigue behavior(107-109 cycles)of 304 Laustenitic stainless steel was studied with ultrasonic fatigue testing system(20kHz).The characteristics of fatigue crack initiation and propagation were discussed based on the observation of surface plastic deformation and heat dissipation.It was found that micro-plasticity(slip markings)could be observed on the specimen surface even at very low stress amplitudes.The persistent slip markings increased clearly along with a remarkable process of heat dissipation just before the fatigue failure.By detailed investigation using a scanning electron microscope and an infrared camera,slip markings appeared at the large grains where the fatigue crack initiation site was located.The surface temperature around the fatigue crack tip and the slip markings close to the fracture surface increased prominently with the propagation of fatigue crack.Finally,the coupling relationship among the fatigue crack propagation,appearance of surface slip markings and heat dissipation was analyzed for a better understanding of ultrasonic fatigue damage behavior.     

Properties of 3Cr2W8V Die Steel With Striations Processed by Laser

 The striations on the surface of 3Cr2W8V die steel were processed by laser. The microstructure, hardness, wear resistance and thermal fatigue behavior of the specimens processed by laser were measured. The appearance and mechanism of thermal fatigue crack propagation in the zone processed by laser were observed and discussed. The results show that the wear resistance and thermal fatigue resistance of materials processed by laser are all better than those of the unprocessed material. The processed zone by laser plays a role in baffling wearing process and crack propagation. The pile nail effect of processed zone is the main factor for improving the wear resistance and thermal fatigue resistance of material.