Effects of tetramethylene sulfone solvent additives on conductivity of PEDOT:PSS film and performance of polymer photovoltaic cells

A solvent additive in PEDOT:PSS solution is one of many methods to improve the conductivity of the poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) films. We explore a new type of the solvent additive, namely tetramethylene sulfone (TMS), for the fabrication of the PEDOT:PSS conductive layer in the ITO/PEDOT:PSS/P3HT:PCBM/TiO_x/Al polymer photovoltaic cells, in comparison to a more common dimethyl sulfoxide (DMSO) solvent additive. At optimal conditions, the TMS additive at 10 wt.% has been found to enhance the conductivity of pristine PEDOT:PSS films from 0.04 S/cm up to approximately 189 S/cm, compared with the highest conductivity for the case of the DMSO additive at 15 wt.% of 117 S/cm. Possible mechanisms of this conductivity enhancement, relating to the polymer conformation and the film morphology, have been investigated by Raman spectroscopy, X-ray diffraction, atomic force microscopy, and transmission electron microscopy. The performance of the polymer photovoltaic cells fabricated with the solvent additives PEDOT:PSS films follows a similar trend to the conductivity of the films as a function of the additive concentration. The additives mainly lead to greater short circuit current density (J_sc) of the photovoltaic cells. The highest power conversion efficiency (PCE) of 2.24% of the device has been obtained with the 10 wt.% TMS additive of, compared to the PCE of 1.48% for the standard device without solvent additive.     

Solution processed WO3 layer for the replacement of PEDOT:PSS layer in organic photovoltaic cells

Tungsten oxide layer is formed uniformly by a sol–gel technique on top of indium tin oxide as a neutral and photo-stable hole extraction layer (HEL). The solution processed tungsten oxide layer (sWO₃) is fully characterized by UV–Vis, XPS, UPS, XRD, AFM, and TEM. Optical transmission of ITO/sWO₃ substrates is nearly identical to ITOs. In addition, the sWO₃ layer induces nearly ohmic contact to P3HT as PEDOT:PSS layer does, which is determined by UPS measurement. In case that an optimized thickness (～10 nm) of the sWO₃ layer is incorporated in the organic photovoltaic devices (OPVs) with a structure of ITO/sWO₃/P3HT:PCBM/Al, the power conversion efficiency (PCE) is 3.4%, comparable to that of devices utilizing PEDOT:PSS as HEL. Furthermore, the stability of OPV utilizing sWO₃ is significantly enhanced due to the air- and photo-stability of the sWO₃ layer itself. PCEs are decreased to 40% and 0% of initial values, when PEDOT:PSS layers are exposed to air and light for 192 h, respectively. In contrast, PCEs are maintained to 90% and 87% of initial PCEs respectively, when sWO₃ layers are exposed to the same conditions. Conclusively, we find that solution processed tungsten oxide layers can be prepared easily, act as an efficient hole extraction layer, and afford a much higher stability than PEDOT:PSS layers.     

Adhesion properties of inverted polymer solarcells: Processing and film structure parameters

We report on the adhesion of weak interfaces in inverted P3HT:PCBM-based polymer solar cells (OPV) with either a conductive polymer, PEDOT:PSS, or a metal oxide, molybdenum trioxide (MoO₃), as the hole transport layer. The PEDOT:PSS OPVs were prepared by spin or spray coating on glass substrates, or slot-die coating on flexible PET substrates. In all cases, we observed adhesive failure at the interface between the P3HT:PCBM with PEDOT:PSS layer. The adhesion energy measured for the solar cells made on glass substrates was about 1.8 J/m², but only 0.5 J/m² for the roll-to-roll processed flexible solar cells. The adhesion energy was insensitive to the PEDOT:PSS layer thickness in the range of 10–40 nm. A marginal increase in adhesion energy was measured with increased O₂ plasma power. Compared to solution processed PEDOT:PSS, we found that thermally evaporated MoO₃ adheres less to the P3HT:PCBM layer, which we attributed to the reduced mixing at the MoO₃/P3HT:PCBM interface during the thermal evaporation process. Insights into the mechanisms of delamination and the effect of different material properties and processing parameters yield general guidelines for the design of more reliable organic photovoltaic devices.     

Stable organic photovoltaic with PEDOT:PSS and MoOX mixture anode interfacial layer without encapsulation

Herein, we report about an efficient and stable organic photovoltaic that uses a poly(3,4-ethylenedioxythiophene):poly(styrene-sulfonate) (PEDOT:PSS) and molybdenum oxide (MoO_X) mixture for the anode interfacial layer, and that can reach 4.43% power conversion efficiency (PCE) under AM1.5 conditions. Utilizing PEDOT:PSS:MoO_X (1:1), the shelf lifetime of poly(3-hexylthiophene) (P3HT), and indene-C₆₀ bisadduct (ICBA)-based solar cells without encapsulation, can be realized with only a 25% deterioration after 672 h of storage in air. Furthermore, we compare the photovoltaic performance of the P3HT:ICBA-based organic photovoltaic with PEDOT:PSS, and PEDOT:PSS:MoO_X, in which PEDOT:PSS:MoO_X has outperformed the others. In addition, the water vapor transmission rate of PEDOT:PSS:MoO_X is 0.17 gm/(m² day), which is much less than that of PEDOT:PSS.     

MoO3/Au/MoO3–PEDOT:PSS multilayer electrodes for ITO-free organic solar cells

The effect of the MoO₃–PEDOT:PSS composite layer in the MoO₃/Au/MoO₃–PEDOT:PSS multilayer electrode on the power conversion efficiency of ITO-free organic solar cells (OSCs) was evaluated. The MoO₃ (30 nm)/Au(12 nm)/MoO₃–PEDOT:PSS (30 nm)/PEDOT:PSS structure showed ~7% more optical transmittance than the MoO₃ (30 nm)/Au (12 nm)/MoO₃(30 nm)/PEDOT:PSS structure at 550 nm wavelength. The OSCs using MoO₃/Au/MoO₃–PEDOT:PSS multilayer electrodes as anodes showed a considerable improvement in power conversion efficiency (PCE), from 1.84% to 2.81%, comparable to ITO based OSCs with PCE of 2.89%. This improvement is attributed to the suppression of MoO₃ dissolution by the acidic hole transport layer (HTL) PEDOT:PSS on the MoO₃/Au/MoO₃–PEDOT:PSS multilayer electrode, resulting in high J_sc, V_oc and FF of the OSCs. This composite based multilayer electrode was shown to be a promising replacement in ITO-free flexible optoelectronic devices.     

Energy level alignment and morphology of interfaces between molecular and polymeric organic semiconductors

Ultraviolet photoelectron spectroscopy (UPS) was used to determine the energy level alignment at organic–organic conductor–semiconductor and semiconductor–semiconductor hetero-interfaces that are relevant for organic optoelectronic devices. Such interfaces were formed by in situ vacuum sublimation of small molecular materials [C₆₀ and pentacene (PEN)] and ex situ spin-coating of poly(3-hexylthiophene) (P3HT), all on the common substrate poly(3,4-ethylenedioxythiophene)/poly(styrenesulfonate) (PEDOT:PSS). We found that the deposition sequence had a significant impact on the interface energetics. The hole injection barrier (HIB) of C₆₀ on PEDOT:PSS could be changed from 1.0 eV (moderate hole injection) to 1.7 eV (good electron injection) by introducing a layer of P3HT. The HIB of P3HT/PEDOT:PSS was increased by 0.35 eV due to an interfacial PEN layer. However, PEN deposited on PEDOT:PSS and P3HT/PEDOT:PSS exhibited the same value. These observations are explained by material-dependent dipoles at the interfaces towards PEDOT:PSS and substrate dependent inter-molecular conformation.     

Isopropanol-treated PEDOT:PSS as electron transport layer in polymer solar cells

Isopropanol (IPA)-treated poly(3,4-ethylenedioxithiophene):poly(styrene sulfonate) (PEDOT:PSS) was applied as a new electron transport layer (ETL) in P3HT:PCBM bulk heterojunction polymer solar cell (BHJ-PSC) devices for the first time, revealing the electron transport property of IPA-treated PEDOT:PSS in sharp contrast to the well known hole transport property of the untreated PEDOT:PSS. Under the optimized condition for incorporating PEDOT:PSS ETL, the power conversion efficiency (PCE) of the ITO/untreated PEDOT:PSS (HTL)/P3HT:PCBM/IPA-treated PEDOT:PSS (ETL)/Al device (3.09%) is quite comparable to that of the reference ITO/untreated PEDOT:PSS (HTL)/P3HT:PCBM/Al device without any ETL (3.06%), and an annealing treatment of PEDOT:PSS ETL at 120 °C for 10 min led to a PCE of 3.25%, which even slightly surpasses that of the reference device, revealing the electron transport property of IPA-treated PEDOT:PSS. The electron transport property of IPA-treated PEDOT:PSS is interpreted by the lowering of the work function of PEDOT:PSS upon IPA treatment and incorporation as ETL as probed by scanning Kelvin probe microscopy (SKPM).     

Effects of UV light-irradiated buffer layer on the performance of polymer solar cells

We investigate the effect of a UV-irradiated poly(3,4-ethylene dioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) buffer layer on the performance of polymer photovoltaic cells based on poly(3-hexylthiophene) (P3HT) and [6,6]-phenyl-C61-butyric acid methyl ester (PCBM) blends. It was found that UV irradiation can reduce the bulk and contact resistance of PEDOT:PSS films, improving the power conversion efficiency from (3.05 ± 0.04)% to (3.50 ± 0.03)% due to the lower device series resistance under an illumination of AM1.5G, 100 mW/cm². The work function change after UV irradiation and negligible surface morphology change was noticed.     

Enhanced performance in inverted polymer solar cells via solution process: Morphology controlling of PEDOT:PSS as anode buffer layer by adding surfactants

Inverted polymer solar cells were fabricated by adding the amphiphilic surfactant ‘Surfynol 104 series’ to Poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) as a anode buffer layer by solution process. With the introduction of Surfynol 104 series-added PEDOT:PSS, it was able to form a homogeneous film by adjusting the wettability of a hydrophobic poly(3-hexylthiophene) (P3HT):[6,6]-phenyl C₆₁-butyric acid methyl ester (PCBM) film. With decrease in series resistance (R_S) and increase in shunt resistance (R_SH), as a result, the short circuit current density (J_SC), open circuit voltage (V_OC) and fill factor (FF) of the optimized device were 10.2 mA/cm², 0.63 V and 61.3%, respectively, calculated the power conversion efficiency (PCE) was 4.0%. In addition, the air stability of the fabricated device was improved.     

Flexible inverted polymer solar cells on polyethylene terephthalate substrate containing zinc oxide electron-collection-layer prepared by novel sol–gel method and low-temperature treatments

Flexible and air-stable polymer solar cells were fabricated on a polyethylene terephthalate (PET) substrate. The cell structure was indium tin oxide (ITO) on PET/zinc oxide (ZnO)/[6,6]-phenyl C₆₁ butyric acid methyl ester (PCBM):regioregular poly(3-hexylthiophene) (P3HT)/poly (3,4-ethylenedioxylenethiophene):poly(4-styrene sulfonic acid) (PEDOT:PSS)/Au, this being called the ZnO cell. Reproducible cell performances were obtained despite the ZnO cells being fabricated in air and at low temperature, using a novel ZnO precursor solution containing zinc(II) acetylacetonate as a metal source and acetylacetone as a Zn²⁺ complexing agent. The power conversion efficiency (PCE) of the flexible ZnO cells without sealing was 2.15% under irradiating AM1.5G simulated sunlight at 100 mW cm^?2. In addition, the performance of the non-sealed ZnO cells was almost constant in ambient atmosphere under continuous light irradiation for 100 h.     

Optical,electrical and mechanical properties of indium tin oxide on polyethylene terephthalate substrates: Application in bulk-heterojunction polymer solar cells

We investigated optical, electrical and mechanical properties of indium tin oxide (ITO) on flexible polyethylene terephthalate (PET) substrate, considering bulk-heterojunction (BHJ) polymer solar cells applications. Encapsulation of flexible solar cells with the architecture PET/ITO/PEDOT:PSS/P3HT:PCBM (or P3HT:PCBM:AZ-NDI-4)/Al was done by direct brush-painting with nail enamel. Active cell layer blends of [6,6]-phenyl C₆₁ butyric acid methyl ester (PCBM) with regioregular or regiorandom poly(3-hexylthiophene-2,5-diyl) (P3HT) were applied. Additionally for this role the mixture of regioregular P3HT:PCBM with naphthalene diimide–imine with four thiophene rings AZ-NDI-4 was tested. Obtained photovoltaic (PV) and optical (UV–vis) results of the flexible polymer solar cells were compared with the same architecture of devices on the glass/ITO substrate.     

Nanocrystal V2O5 thin film as hole-extraction layer in normal architecture organic solar cells

Nanocrystal V₂O₅ dispersion processed thin films are introduced as efficient hole extraction interlayer in normal architecture P3HT:PCBM solar cells. Both thin and rather thick interlayers are studied and demonstrated to work properly in organic photovoltaic. Nanocrystal V₂O₅V₂O₅ layers effectively block electrons and effectively extract holes at the ITO anode. Very constant and high V_OC (above 0.56 V) are easily achieved. Comparable J_SC and PCE are demonstrated for nanocrystal dispersion-processed devices when compared with amorphous sol–gel processed devices. The excellent functionality of nanocrystal V₂O₅ interlayers in Si-PCPDTBT:PCBM devices further demonstrates the broad application potential of this material class for photovoltaic applications.     

Metal salt modified PEDOT:PSS as anode buffer layer and its effect on power conversion efficiency of organic solar cells

The effects of metal chlorides such as LiCl, NaCl, CdCl₂ and CuCl₂ on optical transmittance, electrical conductivity as well as morphology of PEDOT:PSS films have been investigated. Transmittance spectra of spun PEDOT:PSS layers were improved by more than 6% to a maximum of 94% in LiCl doped PEDOT:PSS film. The surface of the PEDOT:PSS films has exhibited higher roughness associated with an increase in the electrical conductivity after doping with metal salts. The improvement in the physical properties of PEDOT:PSS as the hole transport layer proved to be key factors towards enhancing the P3HT:PCBM bulk heterojunction (BHJ) solar cells. These improvements include significantly improved power conversion efficiency with values as high as 6.82% associated with high fill factor (61%) and larger short circuit current density (∼18 mA cm⁻²).     

Hybrid photovoltaic structures based on amorphous silicon and P3HT:PCBM/PEDOT:PSS polymer semiconductors

Hybrid thin film photovoltaic structures, based on hydrogenated silicon (Si:H), organic poly(3-hexythiophene):methano-fullerenephenyl-C61-butyric-acid-methyl-ester (P3HT:PCBM) and poly(3,4ethylenedioxythiophene):poly(4-styrenesulfonate) (PEDOT:PSS) films, have been fabricated. Organic semiconductor thin films were deposited by spin-coating technique and were exposed to radio frequency plasma enhanced chemical vapor deposition (RF PECVD) of Si:H films at deposition temperature T_d = 160 °C. Different types of structures have been investigated: H1) ITO/(p)SiC:H /P3HT:PCBM/(n) Si:H, H2) ITO/PEDOT:PSS/(i)Si:H/(n) Si:H and H3) ITO/PEDOT:PSS/P3HT:PCBM/(i)Si:H/(n)Si:H. Short circuit current density spectral response and current-voltage characteristics were measured for diagnostic of the photovoltaic performance. The current density spectral dependence of hybrid structures which contains organic layers showed improved response (50–80%) in high photon energy range (hν ≈ 3.1–3.5 eV) in comparison with Si:H reference structure. An adjustment in the absorbing layer thickness and in the contact material for ITO/PEDOT:PSS/(i)Si:H/(n)Si:H structure, resulted in a remarkably high short circuit current density (as large as 17.74 mA/cm²), an open circuit voltage of 640 mV and an efficiency of 3.75%.     

Detailed investigation of dependencies of photovoltaic performances of P3HT:PC61BM based solar cells on anodic work function modified by surface treatment of indium-tin-oxide electrode with benzenesulfonyl chloride derivatives

The photovoltaic (PV) characteristics of bulk-heterojunction (BHJ) solar cells based on poly(3-hexylthiophene) and [6,6]-phenyl-C₆₁-butyric acid methyl ester (P3HT:PC₆₁BM) were improved using indium-tin-oxide (ITO) anode electrodes modified chemically with CH₃O-, H-, Cl-, CF₃-, and NO₂-terminated benzenesulfonyl chlorides as a self-assembled monolayer (SAM). The ITO electrode surfaces were easily treated through the chemical modification of the reactive –SO₂Cl binding group, and the work function (WF) of the modified ITO was effectively changed depending on the permanent dipole moments introduced in the para-position of benzenesulfonyl chloride. We examined the correlation between the ITO WFs corrected by the change in the contact potential difference and the calculated dipole moments of the SAM models. Moreover, we examined the PV characteristics of the P3HT:PC₆₁BM based BHJ organic PV cells using the SAMs or poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS)-treated ITOs with different WFs lying within ±0.2 eV from the highest occupied molecular orbital (HOMO) level of P3HT. We found that the enhancement effect of the SAMs on the power-conversion efficiency (η_P) reached a maximum with Cl (η_P = 3.72%), and became larger than that of PEDOT:PSS (η_P = 3.62%). Two distinct J_sc dependencies, increasing and decreasing with the increasing WF of the anode ITO, were observed at higher and lower WFs than the HOMO level of the donor, respectively. Almost constant V_oc values (around 0.6 V) were observed with different SAM-modified ITOs, which suggested that Fermi level pinning was achieved by aligning the anode Fermi level and positive polaronic level of the donor polymer.     

Enhancing the short-circuit current,efficiency of inverted organic solar cells using tetra sulfonic copper phthalocyanine (TS-CuPc) as electron transporting layer

Efficient bulk-heterojunction polymer solar cells based on poly(3-hexylthiophene) (P3HT) blended with a fullerene derivative, [6,6]-phenyl-C61-butyric acid methyl ester (PCBM) were fabricated in inverted configuration by using copper phthalocyanine-3,4′,4′′,4′′′tetra-sulfonated acid tetrasodium salt (TS-CuPc) as the electron collecting layer and MoO₃ as hole collecting layer. TS-CuPc is observed to be critical for the device performance, significantly enhancing the Jsc and the PCE compared to devices based on TiOx. The optimal thicknesses of MoO₃ and TS-CuPc were 10 nm and 15 nm, respectively. Based on these optimal parameters, the PCE of 3.6% was obtained compared to 3.4% for the reference TiOx/P3HT:PCBM/MoO₃/Ag.     

Photo stability enhancement of Poly(3-hexylthiophene)-PCBM nanocomposites by addition of multi walled carbon nanotubes under ambient conditions

Poly(3-hexylthiophene)-Phenyl-C61-butyric acid methyl ester (P3HT–PCBM) composites find wide application in optoelectronic devices, especially bulk-hetero junction (BHJ) solar cells. These composites, even though could give efficient polymer solar cells with ∼4–5% power conversion efficiencies (PCE), a major problem of photo stability is associated with it and remains unsolved. P3HT–PCBM composite was found to be degrading on irradiation with ultraviolet radiation or a solar simulator providing AM1.5G illumination (1000 W m^–2, 72 ± 2 °C or 330 W m⁻², 25 °C), in presence of oxygen and moisture. Here, we have studied the photo stability of P3HT–PCBM under ambient conditions and showed that a new ternary composite, P3HT–PCBM–MWCNT (multi walled carbon nanotube) has superior photo stability even on extended UV–Vis exposure. A total of 7% (w/w) PCBM and 3% (w/w) MWCNT with respect to P3HT resulted in optimum stability. UV–Visible and fluorescence spectral analysis have been used to study the photo stability, both in solution state and solid/film state. Transmission electron micrograph (TEM) along with selected area electron diffraction (SAED) pattern and Field Emission Scanning Electron Microscopy (FE-SEM) micrographs have been used to show the well coating of MWCNT on P3HT–PCBM composite. Since MWCNT is one of the very important carbon based nanomaterial with several supreme characteristics, this new ternary composite has great importance for optoelectronic applications.     

Interfacial layer material derived from dialkylviologen and sol–gel chemistry for polymer solar cells

Sol–gel processible organosilicate material based on dialkylviologen (1,1-(bis-trimethoxysilane)-[4,4′]bipyridium dibromide (bis-trimethoxypropylsilane)-yl-viologen, PV-Si) was synthesized and used as an interfacial layer material for polymer solar cells based on poly(3-hexylthiophene): [6,6]-phenyl-C₆₁-butyric acid methyl ester (P3HT:PCBM). PV-Si is very good soluble in polar protic solvents because of two pyrinium bromide salts and PV-Si pre-polymer can be easily prepared by sol–gel chemistry under the mild acidic conditions. From the ultraviolet spectroscopy (UPS) study, the reduction of the work function of Al and ITO is observed by the formation of interface dipole, which is induced by the thin film of thermally cured PV-Si pre-polymer (cPV-Si) at 180 °C. The open circuit voltage (V_oc) of conventional type polymer solar cell (CPSC) with a structure of ITO/active layer (P3HT:PCBM)/cPV-Si(<5 nm)/Al is 0.58 V, which is higher than the CPSC without cPV-Si (0.55 V). This indicates that the favorable interface dipole is generated by the thin film of cPV-Si. Besides, the power conversion efficiency (PCE) of CPSC with cPV-Si reaches at 2.90%, which is higher than that of the device without cPV-Si (2.69%). Surprisingly, the PCE and the short circuit current (J_sc) of inverted type polymer solar cell (IPSC) with a structure of ITO/cPV-Si (<5 nm)/active layer/WO₃/Ag are 2.83% and ?9.19 mA/cm², respectively, which are higher than those of the device with ZnO (2.51% and ?8.63 mA/cm²) as an electron transporting/injecting layer. This is due to that the work function of ITO is also reduced by the formation of interface dipole. The IPSC with cPV-Si as an interfacial layer (IFL) shows very good rectification and a contact property as well. From the results, the thin layer of cPV-Si is potential material for an IFL for either CPSC or IPSC. Especially, ZnO can be replaced by cPV-Si because of their improved device performances and pretty low processing temperature.     

All-conjugated diblock copolymer of poly(3-hexylthiophene)-block-poly(3-phenoxymethylthiophene) for field-effect transistor and photovoltaic applications

The electronic properties, morphology and optoelectronic device characteristics of conjugated diblock copolythiophene, poly(3-hexylthiophene)-block -poly(3-phenoxymethylthiophene) (P3HT-b-P3PT), are firstly reported. The polymer properties and structures were explored through different solvent mixtures of chloroform (CHCl₃), dichlorobenzene (DCB), and CHCl₃:DCB (1:1 ratio). The absorption maximum (λ_max) of P3HT-b-P3PT prepared from DCB was around 554 nm with a shoulder peak indicative for the highly crystalline structure around 604 nm while that from CHCl₃ was 516 nm without the clear shoulder peak. The field-effect hole mobility of P3HT-b-P3PT increased from ～6.0 × 10^?3, ～8.0 × 10^?3 to ～2.0 × 10^?2 cm² V^?1 s^?1 as the DCB content in the solvent mixture enhanced. The AFM images suggested that the highly volatile CHCl₃ processing solvent led to the amorphous structure, on the other hand, less volatile DCB resulted in the largely crystalline structure of the P3HT-b-P3PT. Such difference on the polymer structure and hole mobility led to the varied power conversion efficiency (PCE) of the photovoltaic cells fabricated from the blend of P3HT-b-P3PT/[6,6]-phenyl-C₆₁-butyric acid methyl ester (PCBM) (1:1, w/w): 1.88 (CHCl₃), 2.13 (CHCl₃:DCB (1:1)), and 2.60% (DCB). The PCBM blend ratio also significantly affected the surface structure and the solar cell performance. The PCE of polymer/PCBM could be improved to 2.80% while the ratio of polymer to PCBM went to 1:0.7. The present study suggested that the surface structures and optoelectronic device characteristics of conjugated diblock copolymers could be easily manipulated by the processing solvent, the block segment characteristic, and blend composition.     

An efficient inverted organic solar cell with improved ZnO and gold contact layers

This paper presents a high efficiency (～3.8%) inverted organic photovoltaic devices based on a P3HT:PCBM bulk heterojunction (BHJ) blend with improved electron- and hole-selective contact layers. Zinc oxide (ZnO) nanoparticle films with different thicknesses are deposited on the transparent electrodes as a nano-porous electron-selective contact layer. A thin gold film is used between the BHJ photoactive layer and the poly(3,4-ethylenedioxythiophene) poly(styrenesulfonate) (PEDOT:PSS), which improves the wettability and significantly enhances the stability of the device (>50 days of air exposure). Photovoltaic device parameters such as power conversion efficiency (PCE) and external quantum efficiency (EQE) are systematically examined for inverted devices with different thicknesses of ZnO and gold layers in comparison to the non-inverted and reference inverted devices with no contact layers. The optimized organic devices with ZnO and Au contact layers show exceptional short circuit currents (in excess of 13 mA/cm²), in comparison to the reference devices, which is related to increased quantum efficiency of the device observed in measured EQE experiments. These results are important for development of high efficiency and stable all-printed organic solar cells and point out the role of contact layers, in particular, ZnO conductivity and morphology in the device performance.