Architecture of Multilayer Cr/CrN Coatings for Wear Protection in Seawater: Cr/CrN Ratio and Total Thickness

Cr/CrN multilayer coatings with various Cr/CrN thickness ratios and total thicknesses were deposited on 316L stainless steel by multi-arc ion plating. The coatings were systematically characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), and nanoindentation. Tribological behaviors were investigated using a ball-on-disk tribometer in artificial seawater. The results showed that the multilayer coating phases changed from Cr₂N + CrN to Cr + Cr₂N + CrN phases with an increase in Cr/CrN thickness ratio. The adhesion showed a slight difference for the coatings with different thickness ratios but significantly increased with total thickness. The hardness was also slightly improved by thickening the coatings. The friction coefficient and wear rate were lowest at a thickness ratio of about 0.3. However, there was no large difference in the friction coefficient between coatings with different thicknesses. The wear rate was lower for the thicker coatings under various loads. The load-bearing capacity was also improved by thickening the coatings.     

Tribological and electrochemical performances of Cr/CrN and Cr/CrN/CrAlN multilayer coatings deposited by RF magnetron sputtering

CrN/CrAlN and Cr/CrN/CrAlN multilayers were grown with dual RF magnetron sputtering. The application of these multilayers will be wood machining of green wood. That is why ball-on-disc and electrochemical tests in NaCl aqueous solution were realized to elucidate the tribological and corrosion behavior of these coatings as they will be exposed to wear and corrosion during wood machining process. The samples/alumina and samples/WC coupling showed different wear mechanisms. The 300 nm thick Cr/CrN/CrAlN multilayer demonstrated the best tribological behavior and corrosion resistance. The influence of growth defects on corrosion resistance has been shown.     

Friction and wear properties of duplex MAO/CrN coatings sliding against Si3N4 ceramic balls in air, water and oil

It is evident that the micro-arc oxidation (MAO) ceramic coatings often exhibit relatively high friction coefficients as sliding against many mating materials. To reduce the friction coefficient for the MAO coatings, the duplex MAO/CrN coatings were deposited on 2024Al alloy using combined micro-arc oxidation and reactive radio frequency magnetron sputtering. The microstructure and phase of the duplex coatings were observed and determined using scanning electron microscope (SEM) and X-ray diffraction (XRD), respectively. The friction and wear behaviors of the duplex coatings sliding against Si₃N₄ balls in air, water and oil were investigated using a ball-on-disk tribometer. The wear rate of the duplex coating was determined by non-contact optical profilometer and the wear tracks on the duplex coatings were observed by SEM. The results showed the CrN coatings mainly consisted of Cr, CrN and Cr₂N phases. The duplex coatings/Si₃N₄ tribopair exhibited the highest friction coefficient in air, while displayed the lowest friction coefficient in oil. When the normal load and the sliding speed increased, the friction coefficient in air increased from 0.65 to 0.72, whereas decreased from 0.58 to 0.36 in water and 0.20 to 0.08 in oil. The specific wear rates for the duplex coatings in air were higher than those in oil. In comparison to the MAO coatings, the duplex MAO/CrN coatings displayed excellent tribological properties under the same conditions.     

Corrosion-wear behaviour of PVD Cr/CrN multilayer coatings for gear applications

At present, one of the most important problems in automobile engines and transmission components is due to tribological processes (friction and wear) that in many cases come accompanied by corrosion processes due to the environmental conditions to which these materials are exposed during their lifetime. Both mechanisms can be minimized by means of the development and the application of adequate coatings that combine low friction with a high corrosion and wear resistance.The new tendencies in industrial PVD coatings to improve their properties are focused in the development of new multilayer and nanostructured coatings. These structures allow in a relatively simple way enhancing their tribological properties and the corrosion resistance that can not be reached by means of the traditional monolayer coatings. The background of this type of coatings consists of the stacking up of several layers with good individual tribological and mechanical properties, but every individual layer has a thickness that can be from hundreds of nanometres down to only 5-10 nm. The properties of these nanostructured coatings depend strongly on the thickness modulation of every individual layer.Concerning PVD coatings, the chrome nitride coatings have demonstrated to possess excellent wear resistance properties. In this work, multilayer Cr/CrN coatings with different individual layer thickness have been deposited on substrates of steel F1272 and silicon. The deposition has been carried out by means of the cathodic arc method alternating an atmosphere of pure Ar with a reactive mixture of N₂/Ar. The multilayers obtained have been analyzed by means of Glow Discharge Optical Emission Spectroscopy (GD-OES) and in some cases by means of FE-SEM obtaining bilayer (Cr/CrN) periods of the order of 220 and 45 nm. The coating characterization has been complemented with hardness and composition measurements as well as by the performance of several wear and corrosion-wear tests.     

Investigation of antiwear coatings deposited by the pvd process

The tribological properties of various PVD‐deposited coatings (vacuum arc method) have been tested, both single‐layer coatings (TiN, CrN, Ti(C,N), and Cr(C,N)) and multilayer coatings (Cr(C,N)/CrN/Cr and CR(C,N)/(CrN+Cr₂N)/CrN/Cr). An unlubricated ball‐on‐disc tribosystem was used in which an Al₂O₃ ball is pressed against a coated steel disc rotating in the horizontal plane. A novelty of the method is the removal of wear debris from the contact zone using a draught of dry argon. This improves the repeatability of the test results and the stability of the tribological characteristics. It is shown that CrN coatings exhibit the best antiwear properties and Ti(C,N) the worst. Multilayer coatings have better antiwear properties than single‐layer ones. The friction coefficients for CrN and Cr(C,N) coatings are much smaller than for the commonly used TiN. A correlation has also been found between the physical properties of the coatings tested (adhesion of the coating to the substrate assessed in scratch tests, and coating hardness) and their antiwear properties. An improvement in coating‐substrate adhesion results in wear reduction, while greater hardness (causing a coating embrittlement increase and a change in the wear mechanism) brings about greater wear. There is no correlation between the physical properties and the friction coefficients of the coatings tested.     

Study of tribological performance of ECR-CVD diamond-like carbon coatings on steel substrates: Part 1. The effect of processing parameters and operating conditions

Diamond-like carbon (DLC) coatings were prepared on AISI 440C steel substrates at room temperature by electron cyclotron resonance chemical vapor deposition (ECR-CVD) process in C₂H₂/Ar plasma. Using the designed Ti/TiN/TiCN/TiC interfacial transition layers, relatively thick DLC coatings (1-2 μm) were successfully prepared on the steel substrates. The friction and wear performance of the DLC coatings was evaluated by ball-on-disk tribometry using a steel counterbody at various normal loads (1-10 N) and sliding speeds (2-15 cm/s). By optimizing the deposition parameters such as negative bias voltage, DLC coatings with hardness up to 30 GPa and friction coefficients lower than 0.15 against the 100Cr6 steel ball could be obtained. The friction coefficient was maintained for 100,000 cycles (∼2.2 km) of dry sliding in ambient environments. In addition, the specific wear rates of the coatings were found to be extremely low (∼10⁻⁸ mm³/Nm); at the same time, the ball wear rates were one order of magnitude lower. The influences of the processing parameters and the sliding conditions were determined, and the frictional behavior of the coatings was discussed. It has been found that higher normal loads or sliding speeds reduced the wear rates of the coatings. Therefore, it is feasible to prepare hard and highly adherent DLC coatings with low friction coefficient and low wear rate on engineering steel substrates by the ECR-CVD process. The excellent tribological performance of DLC coatings enables their industrial applications as wear-resistant solid lubricants on sliding parts.     

Friction and wear behaviour of WC-Co-Cr3C2-VC cemented carbides obtained from nanocrystalline mixtures

The effect of adding Cr₃C_2, VC or a mixture of both as a grain growth inhibitors to cemented carbides obtained from WC-12 wt.%Co nanocrystalline mixtures on the behaviour of friction and dry sliding wear have been studied. All the wear tests were performed on a tribometer with ball on disc configuration, using a WC-6 wt.%Co ball as a counterpart with normal contact loads of 40 and 60 N, sliding distance of 2000 m and a sliding speed of 0.1 m/s. A significant reduction in the wear rates was observed by the effect of the aforementioned additives, in particular for the VC, which showed an increase in the wear resistance of the order of 90%. The analysis of wear and surface damage were correlated to the observed behaviour.     

Effects of carbon content on the high temperature friction and wear of chromium carbonitride coatings

Chromium nitride-based coatings are often used in application at high temperature. They possess high wear and oxidation resistance; however, the friction coefficient is typically very high. Therefore, we doped CrN coatings by carbon with the aim to improve tribological properties at elevated temperature, particularly to lower the friction. CrCN coatings were prepared by cathode arc evaporation technology using constant N₂ flow and variable C₂H₂ flow. The coatings with a thickness of 3-4 μm were deposited on hardened steel substrates and high-temperature resistant alloy. The carbon content varied from 0 at.% (i.e. CrN) up to 31 at.%. The standard coating characterization included the nano-hardness, adhesion, chemical composition and structure (including hot X-ray diffraction). Wear testing was done using a high temperature tribometer (pin-on-disc); the maximum testing temperature was 700 °C. The coatings with carbon content 12-31 at.% showed almost identical tribological behaviour up to 700 °C.     

Friction, wear and N2-lubrication of carbon nitride coatings: a review

Recent results of tribological properties of carbon nitride (CN_x) coatings are reviewed. CN_x coatings of 100 nm thickness were formed on Si-wafer and Si₃N₄ disks by the ion beam mixing method. Friction and wear tests were carried out against Si₃N₄ balls in the environments of vacuum, Ar, N₂, CO₂, O₂ or air by a ball-on-disk tribo-tester in the load range of 80-750 mN and in the velocity range of 4-400 mm/s.It was found that friction coefficient μ is high (μ=0.2-0.4) in air and O₂, and low (μ=0.01-0.1) in N₂, CO₂ and vacuum. The lowest friction coefficient (μ<0.01) was obtained in N₂. It was also found that N₂ gas blown to the sliding surfaces in air effectively reduced the friction coefficient down to μ≈0.017. Wear rate of CN_x coatings varied in the range 10⁻⁹-10⁻⁵ mm³/N m depending on the environment.The wear mechanisms of CN_x in the nanometer scale were studied by abrasive sliding of an AFM diamond pin in air. It was confirmed that the major wear mechanism of CN_x in abrasive friction was low-cycle fatigue which generated thin flaky wear particles of nanometre size.     

CrCN/CrN+ta-C multilayer coating for applications in wood processing

The paper presents mechanical and tribological properties of CrCN/CrN and CrCN/CrN+ta-C multilayer coatings. Tetrahedral carbon (ta-C) layer formed using the pulse cathodic arc evaporation method are characterised by high hardness –45 GPa, very low friction coefficient—below 0.1 and a low wear rate −1.3×10⁻¹⁷ m³N⁻¹ m⁻¹ providing promising application perspectives.Three sets of tools—planer knives for cutterheads were tested: uncoated (as reference), tools with a CrCN/CrN coating and tools with CrCN/CrN coating with additional friction-reducing tetrahedral carbon (ta-C) layer. The results of investigations indicate that the “tool life” depends on the type of coating and machining conditions. The blades covered with CrCN/CrN multilayer coating after machining of dry, seasoned pine timber showed a twofold increase of durability, and knives covered with CrCN/CrN+ta-C multilayer coating were characterised further by about 15% higher durability. Durability of knives tested in the course of rounding of wet pine timber, despite relatively high depth of machining was improved and for cutters with a CrCN/CrN coating increased more than twice, while the use of the additional ta-C layer on the multilayer coating improved durability by almost 5 times.     

A method for the tribological testing of thin,hard coatings

A new method has been developed for tribological testing of thin, hard antiwear coatings, using a ball‐on‐disc tribosystem, under conditions of dry sliding. In this, an Al₂O₃ ball is pressed against a coated steel disc. Wear debris is removed from the contact zone by a stream of dry argon in this novel method. This improves the stability of the tribological properties and the repeatability of the test results. All test conditions are precisely defined, in particular: the type of motion, air relative humidity, ambient temperature, sliding speed, load, tribosystem spatial configuration, substrate material, substrate hardness and roughness, and coating thickness. The method developed has been used to test various physical vapour deposition coatings (deposited by the vacuum arc method), i. e., single‐layer TiN, Ti(C,N), CrN, and Cr(C,N), and multilayer Cr(C,N)/CrN/Cr and Cr(C,N)/(CrN+Cr₂N)/CrN/Cr. It is shown that CrN coatings exhibit the best antiwear properties, and Ti(C,N) the worst. Friction coefficients for CrN and Cr(C,N) coatings are much lower than for the more commonly used TiN. Multilayer coatings have better antiwear properties than single‐layer ones.     

Abrasive Wear Performance of Cr3C2-25%NiCr Coatings by Plasma Spray and CDS Detonation Spray

This work investigates the abrasive wear performance, of thermally sprayed Cr₃C₂-25%NiCr coatings try APS with Ar/H₂, APS with Ar/He and CDS detonation spray against AL₂O₃ and Si0₂-dominaled abrasive papers using a pin-on-disk abrasive tester. The experimental results indicate that the wear resistance of these coatings increases in the order of Cr₃C₂25%NiCr (APS-ArH₂), Cr₃C₂-25%NiCr (APS-Ar/He) and Cr₃C₂-25%NiCr (CDS). The SEM analyses of worn surfaces indicate that the wear mechanisms mainly include abrasion and strain fatigue. Measurements of indentation damage show that the fracture toughness of the three coatings increases just in the same order as wear resistance.     

INVESTIGATION OF NANO-STRUCTURED PVD COATINGS FOR DRY HIGH-SPEED MACHINING

The objective of this paper is to investigate the performance of different categories of hard PVD coatings in terms of friction and tool wear under dry high-speed machining (HSM) conditions. In this study five different categories of commercially available coatings (nano-composite AlTiN/Si₃N₄, nano-crystalline Al₆₇Ti₃₃N and mono-layered Ti₁₀Al₇₀Cr₂₀N) and experimental nano-multilayered coatings (Ti₂₅Al₆₅Cr₁₀N/BCN and Ti₂₅Al₆₅Cr₁₀N/WN) were studied by machining hardened steel AISI H13 (HRC 50). The coefficients of friction against steel versus temperature were measured. Tool wear and cutting forces were measured in-situ under dry high speed machining conditions. The morphology of the worn tools and the chips collected during cutting were studied using an SEM (Scanning Electron Microscopy) and the EDX (Energy Dispersive X-ray analysis). The cutting temperatures were estimated based on the color of the chips generated during cutting. The comparison among these categories of coatings was conducted based on tool wear, coefficient of friction, cutting forces and chip formation. From this study, it was revealed that the solid self-lubricating layers, automatically formed in the cutting zone under elevated temperatures, play a key role in leading to a significant improvement of tool performance under dry high-speed machining.     

Tribological properties of plasma sprayed and laser remelted 75/25 Cr3C2/NiCr coatings

A CO₂ laser was used to fuse based Ni–Cr Cr₃C₂ coatings for the purpose of homogenizing their microstructures and eliminating their porosity. Tests of layer control and wear resistance were carried out on the samples treated with the laser. The results have shown that laser remelting improves the microstructure of the coatings, increases the coating microhardness, and improves coating–substrate adherence. The dry sliding wear behaviour was characterized by the existence of two periods. During the first period the square of the wear volume is proportional to the sliding distance. During the second, the wear volume is proportional to the sliding distance.     

Influence of aging treatment on microstructure, wear and corrosion behavior of a nickel base hardfaced coating

In this work nickel based hardfacing alloy (Colmonoy 5) was deposited on 316 L (N) stainless steel substrate to study the effects of aging treatment on coating microstructure, wear and corrosion properties. Coatings, deposited through plasma transferred arc (PTA) welding process, were aged at 923 K for 5000 h. Microstructural characterization studies carried out by scanning electron microscopy (SEM) and transmission electron microscopy (TEM) revealed the coarsening of dendrites and precipitation of Cr₂₃C₆ particles in the aged coating. The wear behavior of the as deposited and aged coatings was compared in room temperature (RT) and high temperature (823 K) under dry sliding wear condition (pin-on-disc configuration). At RT, aged coating experienced more wear loss when compared to as-deposited. At high temperature, the wear loss was almost same with similar operating wear mechanisms (tribo-oxidation) for both as-deposited and aged coating. From pitting corrosion studies, it was found that aged coatings are more prone to pitting when compared to the as-deposited coatings.     

Comparative evaluation of ambient temperature friction behaviour of thermal sprayed Cr3C2–25(Ni20Cr) coatings with conventional and nano-crystalline grains

Due to their improved hardness and toughness properties, nano-crystalline materials have become attractive for a wide variety of applications. However, as the processing of nano-crystalline materials is quite expensive, efforts have been made to develop coatings using nano-crystalline grains. The present study investigates the ambient temperature friction behaviour of Cr₃C₂–25(Ni20Cr) coatings with nano-crystalline grains (CNG). In the technical process, both, Cr₃C₂–25(Ni20Cr) coatings with conventional grains (CCG), and nano-crystalline grains were deposited using an HVOF technique. Micro-structural characteristics and mechanical properties of the coatings were determined. Friction behaviour of the coatings as a function of different test conditions was evaluated. The specimens worn were examined by a scanning electron microscope (SEM). The results showed that the coefficient of friction of the CNG against 100Cr6 steel is lower than that of CCG against 100Cr6 steel. The principal types of material removal of CNG on the one hand, and CCG on the other, differ. Maps showing the prevalence of different wear mechanisms for different wear conditions were established for both types of coatings.     

Friction and wear behaviour of Thordon XL and LgSn80 in sliding against plasma-sprayed Cr2O3 coatings

This paper studies the friction and wear behaviour of two important bearing materials, Thordon XL and LgSn80, in dry and lubricated sliding vs. plasma-sprayed Cr₂O₃ coatings. As a reference, AISI 1043 steel is also studied under the same conditions. SEM, EDS and surface topography were employed to study the wear mechanisms. The results indicate that the Thordon XL/Cr₂O₃ coating pair gives the lowest dry friction coefficient (0.16) under a normal load of 45.3 N (pressure 0.453 MPa) at a velocity of 1 m/s. The dry friction coefficient of Thordon XL/Cr₂O₃ coating increases to 0.38 under a normal load of 88.5 N (pressure 0.885 MPa). The dry friction coefficients of the LgSn80/Cr₂O₃ coating are in the range of 0.31–0.46. Secondly, both dry wear rate under low normal load (45.3 N) and lubricated wear rate under a load of 680 N for Thordon XL are lower than those of LgSn80 in sliding against plasma-sprayed Cr₂O₃ coatings at a speed of 1 m/s. However, under a normal load of 88.5 N the dry wear rate of Thordon XL is much higher than that of LgSn80. Thirdly, a high viscosity lubricant (SAE 140) leads to lower wear for Thordon XL and LgSn80 than a low viscosity lubricant (SAE 30). Finally, the dominating wear mechanism for Thordon XL is shear fracture when against the plasma-sprayed Cr₂O₃ ceramic coating. For LgSn80 against plasma-sprayed Cr₂O₃ ceramic coating, abrasive wear is the governing failure mechanism.     

Low Friction CrNMPP/TiNDCMS Multilayer Coatings

Transition metal nitrides like CrN and TiN are widely used in automotive applications due to their high hardness and wear resistance. Recently, we showed that a multilayer architecture of CrN and TiN, deposited using the hybrid—high power impulse magnetron sputtering (HIPIMS) and direct current magnetron sputtering (DCMS)—HIPIMS/DCMS deposition technique, results in coatings which indicate not only increased mechanical and tribological properties but also friction coefficients in the range of diamond-like-carbon coatings when tested at RT and ambient air conditions. The modulated pulsed power (MPP) deposition technique was used to replace the HIPIMS powered cathode within this study to allow for a higher deposition rate, which is based on the complex MPP pulse configuration. Our results on MPP/DCMS deposited CrN/TiN multilayer coatings indicate excellent mechanical and tribological properties, comparable to those obtained for HIPIMS/DCMS. Hardness values are around 25 GPa with wear rates in the range of 2 × 10⁻¹⁶ Nm/m³ and a coefficient of friction around 0.05 when preparing a superlattice structure. The low friction values can directly be correlated to the relative humidity in the ambient air during dry sliding testing. A minimum relative humidity of 13% is necessary to guarantee such low friction values, as confirmed by repeated tests, which are even obtained after vacuum annealing to 700 °C. Our results demonstrate that the co-sputtering of high metal ion sputtering techniques and conventional DC sputtering opens a new field of applications for CrN/TiN coatings as high wear resistance and low friction coatings.     

Sliding tribological behavior of AlCrN coating

The sliding tribological behavior of the PVD AlCrN coating against Si₃N₄ ball have been investigated by using the CETR multi-functional UMT-2 test system under two sliding conditions (bidirectional and unidirectional). Reciprocating sliding tests (bidirectional) were performed under varied normal loads (5, 10 and 20 N) at sliding velocity of 0.48 m/min. Ball-on-disc tests (unidirectional) were performed at varied sliding velocities (0.48 and 5 m/min) under normal load of 5 N. The wear scars of the coating were evaluated by surface profilometer, scanning electron microscopy (SEM), energy-dispersive spectroscopy (EDX), X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS), and the sliding wear mechanism of the coating was consequently discussed. The results showed that AlCrN coating had excellent anti-abrasion properties. Both the normal load in reciprocating sliding test and the sliding velocity in ball-on-disc test had significant influence on the sliding tribological behavior of the AlCrN coating. The combination of abrasion and oxidation was the main sliding wear mechanism for the AlCrN coating. The wear resistant and thermally stable oxides formed by the tribo-chemical reactions of chromium and aluminum protected the AlCrN coating against wear admirably.     

Study of tribological performance of ECR-CVD diamond-like carbon coatings on steel substrates: Part 2. The analysis of wear mechanism

This paper describes the tribological performance of diamond-like carbon (DLC) coatings deposited on AISI 440C steel substrates by electron cyclotron resonance chemical vapor deposition (ECR-CVD) process. A variety of analytic techniques were used to characterize the coatings, such as Raman spectroscopy, atomic force microscopy (AFM) and nano-indentation. The sliding wear and friction experiments were carried out by the conventional ball-on-disk tribometry against 100Cr6 steel counterbody at various normal loads (1-10 N) and sliding speeds (2-15 cm/s). All the wear tests were conducted under dry sliding condition in ambient air for a total rotation cycle of 1 × 10⁵ (sliding distance ∼2.2 km). Surfaces of the coatings and the steel balls were examined before and after the sliding wear tests. The DLC coatings that had been tested all showed relatively low values of friction coefficient, in the range of 0.1-0.2 at a steady-state stage, and low specific wear rates (on the order of 10⁻⁸ mm³/Nm). It was found that higher normal loads or sliding speeds reduced the wear rates of the coatings. Plastic deformation became more evident on the coating surface during the sliding wear test at higher contact stresses. The friction-induced transformation of the coating surface into a graphite-like phase was revealed by micro-Raman analysis, and the flash temperature of the contact asperities was estimated. It was suggested that the structural transformation taking place within the wear tracks was mainly due to the formation of compact wear debris layer rather than the frictional heating effect. On the other hand, an adherent transfer layer (tribolayer) was formed on the counterface, which was closely related to the steady-state friction during sliding and the wear mechanisms. Fundamental knowledge combined with the present tribological study led to the conclusion that adhesive wear along with abrasion was probably the dominant wear mechanism for the DLC/steel sliding systems. Additionally, fatigue processes might also be involved in the wear of the coatings.