Morphology and physical properties of nanocomposites based on poly(methyl methacrylate)/poly(vinylidene fluoride) blends and multiwalled carbon nanotubes

Nanocomposites of blends of poly(vinylidene fluoride) (PVDF) and poly(methyl methacrylate) (PMMA) with multiwalled carbon nanotubes (CNTs) were prepared by melt mixing and hot press molding followed by quenching or annealing (120°C, 24 h). PMMA‐rich nanocomposites showed higher electrical conductivity than PVDF‐rich samples at identical CNT loading. At a specific composition, the quenched nanocomposites showed electrical conductivity values three to four orders of magnitude higher than those observed in annealed samples. Measurement of the dielectric constants also supported the electrical conductivity results. In the annealed samples, agglomerated CNTs located mainly in the PVDF crystalline phase were observed. Addition of CNTs promoted the crystallization, and especially, the formation of β‐crystals, which was confirmed by X‐ray diffraction. The thermal behavior of nanocomposites from differential scanning calorimetry (DSC) analysis was explained in terms of the three‐phase model involving the presence of the rigid amorphous fraction, the mobile amorphous fraction, and the crystalline phase. POLYM. COMPOS., 36:1195–1204, 2015. © 2014 Society of Plastics Engineers     

Effect of clay addition on the morphology and thermal behavior of polyamide 6

The nanostructure, morphology, and thermal properties of polyamide 6 (PA6)/clay nanocomposites were studied with X‐ray scattering, differential scanning calorimetry (DSC), and transmission electron microscopy (TEM). The wide‐angle X‐ray diffraction (WAXD) and TEM results indicate that the nanoclay platelets were exfoliated throughout the PA6 matrix. The crystallization behavior of PA6 was significantly influenced by the addition of clay to the polymer matrix. A clay‐induced crystal transformation from the α phase to the γ phase for PA6 was confirmed by WAXD and DSC; that is, the formation of γ‐form crystals was strongly enhanced by the presence of clay. With various clay concentrations, the degree of crystallinity and crystalline morphology (e.g., spherulite size, lamellar thickness, and long period) of PA6 and the nanocomposites changed dramatically, as evidenced by TEM and small‐angle X‐ray scattering results. The thermal behavior of the nanocomposites was investigated with DSC and compared with that of neat PA6. The possible origins of a new clay‐induced endothermic peak at high temperature are discussed, and a model is proposed to explain the complex melting behavior of the PA6/clay nanocomposites. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 1191–1199, 2007     

Solid state 19F NMR study of crystal transformation in PVDF and its nanocomposites

The polymorphism of poly(vinylidene fluoride) (PVDF) and its nanocomposites was studied by means of solid state nuclear magnetic resonance spectroscopy. ¹³C cross polarization magic angle spinning (¹³C CP MAS) NMR spectra were recorded using simultaneous high‐power decoupling on both the proton and fluorine channels. Both ¹H → ¹³C and ¹⁹F → ¹³C CP experiments were conducted, giving identical results apart from intensity variations due to the CP efficiency. Two main resonances for the CF₂ and the CH₂ groups were observed for both neat PVDF (PVDF‐C0) and the nanocomposite containing 2 wt% clay (PVDF‐C2) samples. ¹⁹F CP MAS spectra were obtained from long proton spin‐lock experiments with a shorter contact time. The results showed two strong resonances at ?84 and ?98 ppm with equal intensities, representing the α‐form crystalline structure of PVDF. It was shown that the clay induces the crystallization of PVDF in β‐form. Our earlier investigations using thermal analysis and X‐ray scattering methods also showed crystal transformation of PVDF in its clay nanocomposites. POLYM. ENG. SCI. 46:1684–1690, 2006. © 2006 Society of Plastics Engineers     

Polymerization kinetics and thermal properties of dicyanate/clay nanocomposites

The polymerization kinetics and thermal properties of dicyanate/clay nanocomposites were investigated. A type of organically modified clay was used as nanometer‐size fillers for the thermosetting dicyanate resin. Differential scanning calorimetry (DSC) was used to study the curing behavior of the dicyanate/clay nanocomposite systems. The polymerization rate of the nanocomposite systems increased with increasing clay content. An autocatalytic reaction mechanism could adequately describe the polymerization kinetics of the dicyanate/clay nanocomposite systems. The polymerization kinetic parameters were determined by fitting the DSC conversion data to the proposed kinetic equation. The glass‐transition temperature of the dicyanate/clay nanocomposites increased with increasing clay content. The thermal decomposition behavior of the dicyanate/clay nanocomposites was investigated by thermogravimetric analysis. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 1955–1960, 2004     

Investigation of the physico‐mechanical properties of electrospun PVDF/cellulose (nano)fibers

The electro‐activity and mechanical properties of PVDF depends mainly on the β‐phase content and degree of crystallinity. In this study, cellulose fibers were used to improve these characteristics. This could be achieved because the hydroxyl groups on cellulose would force the fluorine atoms in PVDF to be in the trans‐conformation, and the cellulose particles could act as nucleation centers. Electrospinning was used to prepare the PVDF/cellulose (nano)fibrous films, and this improved the total crystallinity and the formation of β‐crystals. However, the presence and amount of cellulose in PVDF were found to have little influence on the β‐phase content and on the total crystallinity of PVDF. Improvements in the extent of crystallinity and the β‐phase content were primarily brought about by the chain‐ and crystal orientation as a result of electrospinning. The thermal stability of PVDF in the composites slightly increased with increasing cellulose content in the composites up to 1.0 wt %, while the modulus and tensile strength significantly increased up to the same filler level. The dielectric storage permittivity also increased with increasing cellulose content, but the presence of cellulose had no influence on the dynamics of the γ‐ and β‐relaxations of the PVDF. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43594.     

Structure and properties of polypropylene/clay nanocomposites compatibilized by solid‐phase grafted polypropylene

Polypropylene/organic‐montmorillonite (PP/OMMT) nanocomposites were prepared via a solid‐phase PP graft (TMPP) with a higher grafting level as the compatibilizer. The effects of the compatibilizer on the structure and properties of PP/OMMT nanocomposites were investigated. The structure of the nanocomposites were characterized by X‐ray diffraction (XRD), scanning electron microscopy (SEM), and transmission electron microscopy (TEM). The results showed that when the weight ratio of TMPP and OMMT is greater than 1:1, the OMMT can be dispersed in PP matrix uniformly at the nanoscale. The mechanical properties of the nanocomposites reached a maximum when the weight ratio of TMPP and OMMT is 1:1, although more uniform dispersion was achieved at a higher content of TMPP. The mechanical properties of the nanocomposites decrease with the content of TMPP. The crystallization behavior, dynamic rheological property, and thermal stability of the nanocomposites were investigated by differential scanning calorimetry (DSC), dynamic rheological analysis, and thermal gravimetric analysis (TGA), respectively. Due to the synergistic effects of TMPP and OMMT on the crystallization of PP, the crystallization peak temperature of the nanocomposites increased remarkably compared with that of the neat PP. TMPP shows β‐phase nucleating ability and OMMT promotes the development of β‐phase crystallite. The nanocomposites show restricted melt flow and enhanced temperature sensitivity compared with the neat PP. The thermal stability of the nanocomposites is obviously improved compared with that of the neat PP. POLYM. COMPOS., 2008. © 2008 Society of Plastics Engineers.     

Studies on crystallization behaviors and crystal morphology of polyamide 66/clay nanocomposites

X‐ray diffraction methods, DSC thermal analysis, and polarized light microscopy (PLM) were used to investigate the structural changes of nylon 66/clay nanocomposites. PA 66/clay nanocomposites were prepared by the method of melt intercalation. The results indicate that the addition of the intercalated organo‐montmorillonite (OMMT) can induce generation of the β‐form crystal of PA 66 and substantially affect the arrangement of molecules in the α‐form crystal, although the crystallinity scarcely changes. Also, the DSC results indicate that the addition of OMMT in the PA 66 matrix leads to increases of crystallization temperatures and the full width at half maximum (FWHM) of the exothermic peaks. Moreover, the viscosity factor is the main influence on FWHM of the exothermic peaks of PA 66/clay nanocomposites. The results of nonisothermal crystallization kinetics show that OMMT has the effect of heterogeneous nucleation and leads to the decrease of the size of the spherocrystal. The heterogeneous nucleation effects of OMMTs influence the mechanism of crystallization and the growth mode of PA 66 crystals. PLM photographs verify that the size of spherocrystal is decreased and visually confirm the theory of crystallization kinetics. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 95: 756–763, 2005     

Effect of multi‐walled carbon nanotubes on crystallization,thermal, and mechanical properties of poly(vinylidene fluoride)

Composites were prepared by solution blending poly(vinylidene fluoride) (PVDF) and multi‐walled carbon nanotubes (MWNTs). Fourier transform infrared spectroscopy (FTIR) and X‐ray diffraction (XRD) results showed that the crystalline structure of PVDF was changed by the addition of MWNTs and a MWNTs‐induced crystal transformation from α‐phase to β‐phase of PVDF was confirmed. With differential scanning calorimeter (DSC) and dynamic mechanic thermal analysis (DMA) techniques, thermal and mechanical properties of the composite films were examined. As the DSC results showed, addition of MWNTs would lead to the increased cooling crystallization temperature (T_c), implying that MWNTs nanoparticles could act as nucleating agents, which is further proved with the help of polarized optical microphotographs. On the other hand, the decreasing of D_d (degree of crystallinity) implied that the MWNTs networks can confine the crystallization of PVDF. Through the curve analysis of the dynamic mechanical measurements, it was found that the storage modulus (E′) is significantly enhanced, revealing that a strong interaction should exist between PVDF and MWNTs. POLYM. COMPOS., 2010. © 2009 Society of Plastics Engineers     

Dielectric properties of multiwalled carbon nanotube/clay/polyvinylidene fluoride nanocomposites: Effect of clay incorporation

This study investigates the effect of clay addition on the broadband dielectric properties of multi‐walled carbon nanotube/polyvinylidene fluoride (MWCNT/PVDF) composites, that is, frequency range of 10¹−10⁶ Hz. Different loadings of MWCNT and clay were used for the preparation of three‐phase (MWCNT/Clay/PVDF) nanocomposites via melt‐mixing method. The crystalline structure and morphology of nanocomposites were examined by employing characterization techniques such as X‐ray diffraction, transmission electron microscopy, and differential scanning calorimetry. The dielectric spectroscopy showed that introducing clay into the MWCNT/PVDF nanocomposites at a critical MWCNT concentration improved dielectric properties tremendously. It was interestingly observed that the incorporation of a specific amount of clay, that is, 1.0 wt%, into the (MWCNT/PVDF) nanocomposite at a critical MWCNT loading, that is, 0.5 wt% MWCNT, resulted in a huge increase in the dielectric permittivity (670% at 100 Hz) and a considerable reduction in the dissipation factor (68% at 100 Hz). POLYM. COMPOS., 161–167, 2016. © 2014 Society of Plastics Engineers     

Nanocomposite films of poly(vinylidene fluoride) filled with polyvinylpyrrolidone‐coated multiwalled carbon nanotubes: Enhancement of β‐polymorph formation and tensile properties

To improve interactions between carbon nanotubes (CNTs) and poly(vinylidene fluoride) (PVDF) matrix, multiwalled CNTs (MWCNTs) were successfully coated with amphiphilic polyvinylpyrrolidone (PVP) using an ultrasonication treatment performed in aqueous solution. It was found that PVP chains could be attached noncovalently onto the nanotubes' surface, enabling a stable dispersion of MWCNTs in both water and N,N‐dimethylformamide. PVP‐coated MWCNTs/PVDF nanocomposite films were prepared by a solution casting method. The strong specific dipolar interaction between the PVP's carbonyl group (C?O) and the PVDF's fluorine group C?F₂ results in high compatibility between PVP and PVDF, helping PVP‐coated MWCNTs to be homogenously dispersed within PVDF. Fourier transform infrared and X‐ray diffraction characterization revealed that the as‐prepared nanocomposite PVDF films exhibit a purely β‐polymorph even at a very low content of PVP‐wrapped MWCNTs (0.1 wt%) while this phase is totally absent in the corresponding unmodified MWCNTs/PVDF nanocomposites. A possible mechanism of β‐phase formation in PVP‐coated MWCNTs/PVDF nanocomposites has been discussed. Furthermore, the tensile properties of PVDF nanocomposites as function of the content in PVP‐coated MWCNTs were also studied. Results shows that the addition of 2.0 wt% of PVP‐coated MWCNTs lead to a 168% increase in Young's modulus and a 120% in tensile strength. POLYM. ENG. SCI., 2013. © 2012 Society of Plastics Engineers     

Effect of nanoclay on the morphology and properties of acrylonitrile butadiene styrene toughened polyoxymethylene (POM)/clay nanocomposites

Here, we report the morphology and properties of melt‐blended poly(acrylonitrile‐butadiene‐styrene) (ABS) toughened polyoxymethylene (POM)/clay nanocomposites at different clay loadings (2.5 and 5 phr). The number average domain diameter (D_n) of the ABS droplets in the (75/25 w/w) POM/ABS blend was gradually decreased with increase in clay loading. The X‐ray diffraction (XRD) study and transmission electron microscopic (TEM) analysis of the (75/25 w/w) POM/ABS/clay nanocomposites revealed that, the major amount of clay silicates was dispersed selectively in the POM phase of the blend with an exfoliated morphology. The thermal stability of the (75/25 w/w) POM/ABS blend was increased with the increase in clay loadings. Differential scanning calorimetry (DSC) study suggested the enhancement in the non‐isothermal crystallization temperature of the matrix polymer in the blend/clay nanocomposites. The rheological study revealed a shear thinning behavior in the nanocomposites indicating good processability of the nanocomposites. The solvent uptake property of the blend was decreased in the presence of small amount of the clay in the nanocomposites. The tensile strength and Young modulus of the (75/25 w/w) POM/ABS blend were increased, whereas, percent elongation of the blend was decreased with increasing the clay content. The toughening effect of the ABS was prominent in the POM/ABS/clay nanocomposites compared to the pristine polymer. POLYM. COMPOS., 35:273–282, 2014. © 2013 Society of Plastics Engineers     

Graphene nanocomposites based on poly(vinylidene fluoride): Structure and properties

A nanocomposite of Poly(vinylidene fluoride) (PVDF) was prepared with graphene sheets (GSs), which are a novel filler by a solution method. The structure‐properties relationships of PVDF/GSs nanocomposites were studied. The results of differential scanning calorimetry and X‐ray diffraction show that addition of GSs to the PVDF matrix promotes an α phase to β phase transformation of the polymer crystal. The nanocomposites exhibit significant increases in dynamic mechanical properties and thermal stability compared to the neat PVDF. In addition, the incorporation of GSs in PVDF indicated excellent optical transparency at the lowest weight fractions of GSs and modified wettability of PVDF. POLYM. COMPOS., 2011. © 2011 Society of Plastics Engineers     

Influence of clay content on the melting behavior and crystal structure of nonisothermal crystallized poly(L‐lactic acid)/nanocomposites

To study the effect of organophilic clay concentration on nonisothermal crystallization, poly(L ‐lactic acid) (PLLA)/montmorillonite (MMT) nanocomposites were prepared by mixing various amounts of commercial MMT (Cloisite^® 30B) and PLLA. The effect of MMT content on melting behavior and crystal structure of nonisothermal crystallized PLLA/MMT nanocomposites was investigated by differential scanning calorimetry (DSC), small‐angle X‐ray scattering, and wide‐angle X‐ray diffraction (XRD) analyses. The study was focused on the effect of the filler concentration on thermal and structural properties of the nonisothermally crystallized nanocomposite PLLA/MMT. The results obtained have shown that at filler loadings higher than 3 wt %, intercalation of the clay is observed. At lower clay concentrations (1–3 wt %), exfoliation predominates. DSC and XRD analysis data show that the crystallinity of PLLA/MMT composites increases drastically at high clay loadings (5–9 wt %). In these nanocomposites, PLLA crystallizes nonisothermally in an orthorhombic crystal structure, assigned to the α form of PLLA. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Thermal and mechanical properties of melt processed intercalated poly(methyl methacrylate)–organoclay nanocomposites over a wide range of filler loading

BACKGROUND: Poly(methyl methacrylate) (PMMA)–organoclay nanocomposites with octadecylammonium ion‐modified montmorillonite, prepared via melt processing, over a wide range of filler loading (2–16 wt%) were investigated in detail. These hybrids were characterized for their dispersion structure, and thermal and mechanical properties, such as tensile modulus (E), break stress (σ_brk), percent break strain (ε_brk) and ductility (J), using wide‐angle X‐ray diffraction, transmission electron microscopy, differential scanning calorimetry (DSC), thermogravimetric analysis (TGA) and tensile and impact tests. RESULTS: Intercalated nanocomposites were formed even in the presence of 16 wt% clay (high loading) in PMMA matrix. PMMA intercalated into the galleries of the organically modified clay, with a change in d‐spacing in the range 11–16 Å. TGA results showed improved thermal stability of the nanocomposites. The glass transition temperature (T_g) of the nanocomposites, from DSC measurements, was 2–3 °C higher than that of PMMA. The ultimate tensile strength and impact strength decreased with increasing clay fraction. Tensile modulus for the nanocomposites increased by a significant amount (113%) at the highest level of clay fraction (16 wt%) studied. CONCLUSION: We show for the first time the formation of intercalated PMMA nanocomposites with alkylammonium‐modified clays at high clay loadings (>15 wt%). Tensile modulus increases linearly with clay fraction, and the enhancement in modulus is significant. A linear correlation between tensile strength and strain‐at‐break is shown. Thermal properties are not affected appreciably. Organoclay can be dispersed well even at high clay fractions to form nanocomposites with superior bulk properties of practical interest. Copyright © 2007 Society of Chemical Industry     

Preparation and characterization of polystyrene–clay nanocomposites by free‐radical polymerization

The polymerizable cationic surfactant, vinylbenzyldimethylethanolammouium chloride (VBDEAC), was synthesized to functionalize montmorillonite (MMT) clay and used to prepare exfoliated polystyrene–clay nanocomposites. The organophilic MMT was prepared by Na⁺ exchanged montmorillonite and ammonium cations of the VBDEAC in an aqueous medium. Polystyrene–clay nanocomposites were prepared by free‐radical polymerization of the styrene containing intercalated organophilic MMT. Dispersion of the intercalated montmorillonite in the polystyrene matrix determined by X‐ray diffraction reveals that the basal spacing is higher than 17.6 nm. These nanocomposites were characterized by differential scanning calorimetry (DSC), transmission electron micrograph (TEM), thermal gravimetric analysis (TGA), and mechanical properties. The exfoliated nanocomposites have higher thermal stability and better mechanical properties than the pure polystyrene. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 1370–1377, 2002     

Coaxial electrospun nanofibers of poly(vinylidene fluoride)/polyaniline filled with multi‐walled carbon nanotubes

Core‐shell nanofibers of poly (vinylidene fluoride)/polyaniline/multi‐walled carbon nanotubes (PVDF/PANi/MWCNTs) have been produced using the coaxial electrospinning technique. The nanofibers were semiconductive and had better piezoelectric properties than pure PVDF nanofibers. Piezoelectric PVDF nanofibers are capable of converting mechanical energy into electrical energy, which can be stored in charge storage devices. However, PVDF is not conductive and therefore, a conductive associate material is needed to transfer accumulated static charges into the capacitor. Fourier Transform Infrared (FTIR) spectroscopy and differential scanning calorimetry (DSC) were carried out to study the crystalline β‐phase of PVDF. There was an increase in β‐phase in the electrospun PVDF nanofibers filled with MWCNTs as compared with compression molded samples of neat PVDF. Incorporation of PANi as an intrinsically conductive polymer (ICP) and MWCNTs as conductive nanofiller helps the movement of static charges. Core‐shell nanofibers had conductivities of about seven orders of magnitude higher than simple electrospun nanofibers. POLYM. COMPOS., 35:1198–1203, 2014. © 2013 Society of Plastics Engineers     

Changes in the melting temperature and crystal structure of poly(vinylidene fluoride) by knotting

A significant increase in the melting temperature of knotted fibers of poly(vinylidene fluoride) (PVDF) was detected by differential scanning calorimetry. The melting peak partially returned to the original peak after the fibers were unknotted. Knotted PVDF fibers were observed with an optical microscope at crossed‐nicol conditions. The knotted portions of the fibers showed birefringence even above the melting temperature of the fibers before knotting. The dependence of the physical properties of PVDF under applied stress was estimated in order to investigate the influence of knotting. The fracture temperature of PVDF fibers increased with applied stress below 1 MPa and decreased above 10 MPa because the applied stress increased the melting temperature of PVDF crystals, but strong stress mechanically broke the fibers. The X‐ray diffraction patterns of the PVDF fibers under different stress were divided into the peaks of α‐ and β‐phase crystals and amorphous. The peak area of the β‐phase crystal increased and that of the amorphous decreased with applied stress. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Morphology and properties of highly filled iPP/TiO2 nanocomposites

Nanocomposites based on isotactic polypropylene (iPP) and titanium dioxide (TiO₂) nanoparticle containing 1–15 vol% (4.6–45.5 wt%) of the nanoparticle were prepared by the melt blending process. The effect of an anhydride‐modified polypropylene as a compatibilizer on dispersion of TiO₂ nanoparticles was assessed using SEM. TGA and DSC analysis were performed to study the thermal properties of the nanocomposites. Crystalline structures of iPP in the presence of TiO₂ were analyzed by XRD. Mechanical properties of the nanoparticles were measured and a micromechanical analysis was applied to quantify interface interaction between the polymer and particle. SEM results revealed improvement of TiO₂ particle dispersion by adding the compatibilizer. It was shown that the thermal stability and crystalline structure of the nanocomposite are significantly affected by the state of particle dispersion. TiO₂ nanoparticles were shown to be strong β‐nucleating agents for iPP, especially at concentrations less than 5 vol%. Presence of the β‐structure crystals reduced the elastic modulus and yield strength of the nanocomposites. Micromechanical analysis showed enhanced interaction between organic and inorganic phases of the compatibilized nanocomposites. POLYM. ENG. SCI., 54:874–886, 2014. © 2013 Society of Plastics Engineers     

Preparation,crystallization behavior,and dynamic mechanical property of nanocomposites based on poly(vinylidene fluoride) and exfoliated graphite nanoplate

Nanocomposites based on poly(vinylidene fluoride) (PVDF) and exfoliated graphite nanoplate (xGnP) were prepared by solution precipitation method. The resulting nanocomposites were investigated with respect to their structure and properties by scanning electron microscopy (SEM), transmission electron microscopy (TEM), differential scanning calorimetry (DSC), wide‐angle X‐ray diffraction, and dynamic mechanical analysis. Both SEM and TEM examinations confirmed the good dispersion of xGnP in the PVDF matrix. The nonisothermal crystallization behavior of the PVDF/xGnP nanocomposites was studied using DSC technique at various cooling rates. The results indicated that the xGnPs in nanometer size might act as nucleating agents and accelerated the overall nonisothermal crystallization process. Meanwhile, the incorporation of xGnP significantly improved the storage modulus of the PVDF/xGnP nanocomposites. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Facile and effective promotion of β crystalline phase in poly(vinylidene fluoride) via the incorporation of imidazolium ionic liquids

In this study, a facile and efficient protocol to enhance the β‐phase content of poly(vinylidene fluoride) (PVDF) is developed, in which the effect of room temperature ionic liquids (RTILs), including [1‐butyl‐3‐methylimidazolium (bmim)][PF₆], [bmim][BF₄], [bmim][FeCl₄] and [bmim][Cl], on the crystallization behavior of PVDF is investigated. The resulting PVDF/RTIL hybrids are characterized by Fourier transform infrared (FTIR) spectroscopy, XRD, polarized optical microscopy (POM) and DSC. The FTIR spectroscopy and XRD results show that the fraction of β‐phase, F(β), is significantly enhanced by the incorporation of RTILs, specifically from 49.2% for neat PVDF to 92.6% for hybrid filled with 15 wt% [bmim][PF₆]. The analysis of the crystallization behavior based on the DSC tests reveals that the degree of crystallinity increases with incorporation of RTILs, implying that RTILs could act as directing agents to facilitate the crystallization process, which is further evidenced by the POM results. In addition, the non‐isothermal crystallization kinetics of PVDF and PVDF/RTIL composites are investigated by means of DSC and the results indicate that the addition of the RTILs significantly influences the mechanism of nucleation and growth of PVDF crystallites. © 2013 Society of Chemical Industry