Graft copolymerization of methoxyacrylethyl phosphate onto expanded poly(tetrafluoroethylene) facial membranes

Expanded poly(tetrafluoroethylene) (ePTFE) membranes were modified by graft copolymerization with methoxyacrylethyl phosphate (MOEP) in methyl ethyl ketone (MEK) solutions at ambient temperature using gamma irradiation. The effect of monomer concentration (3–30%) was studied and the modified membranes were characterized by weight increase, x‐ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), contact angle measurements, and differential scanning calorimetry (DSC). Results show that the ePTFE membrane had a degree of crystallinity of 59% and that this did not significantly change after grafting indicating that grafting occurs in the amorphous regions. SEM images showed a globular surface morphology for the grafted membranes. XPS was used to evaluate the chemical structure of the graft copolymer and to determine the XPS grafting extent using the C‐F (ePTFE membrane) and the C‐C (MOEP graft copolymer) peaks. The graft yield as well as grafting extent was found to increase with increasing monomer concentration. Concomitantly, the contact angle was found to decrease with increasing monomer concentration. No direct correlation was found between XPS grafting extent and the advancing water contact angle illustrating that the former does not adequately give an indication of the copolymer surface coverage of the first molecular layer. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Temperature‐sensitive membranes prepared by the plasma‐induced graft polymerization of N‐Isopropylacrylamide into porous polyethylene membranes

A temperature‐responsive polymer, poly(N‐isopropylacrylamide) (PNIPAAm), was grafted onto porous polyethylene membranes by a plasma‐induced graft polymerization technique. A wide range of grafting was achieved through variations in the grafting conditions, including the postpolymerization temperature, time, monomer concentration, and graft‐reaction medium. The active species induced by plasma treatment was proven to be long‐living via a postpolymerization time of 95 h. Different solvent compositions, that is, water, methanol, benzene, and water/methanol, were used as reaction media, and water showed a much higher polymerization rate than the organic solvents. Based on the hydrophilicity of the active species, a mechanism explaining the solvent effect in plasma‐induced graft polymerization was examined. Characterizations by scanning electron microscopy, X‐ray photoelectron spectroscopy (XPS), and micro Fourier transform infrared showed that the grafted polymers were located on both the outer surface and inside pores of the membranes. The XPS analysis also confirmed that the polar amide groups tended to distribute more outward when grafted PNIPAAm was in its expanding state than when it was in its shrinking state. Water permeation experiments showed that the permeability of the grafted membranes varied dramatically with a slight temperature change in the vicinity of the lower critical solution temperature (LCST) of PNIPAAm. The effective pore radii of the grafted membranes above and below the LCST could be depicted by Hagen‐Poiseuille's law. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 3180–3187, 2003     

Radiation-induced grafting of acrylic acid onto expanded poly(tetrafluoroethylene) membranes

Expanded poly(tetrafluoroethylene) (ePTFE) is currently being applied in facial reconstruction surgery. One requirement for the use of ePTFE membranes in soft tissue replacements is establishment of a well-bonded interface with the surrounding bone. However, ePTFE is classified as bioinert, thus lacking in biomimetic properties which may result in poor osseointegration at the bone–implant interface. Thus, the introduction of functional groups onto the polymer surface was carried out in the current study using radiation induced grafting of acrylic acid (AA) yielding graft yields of up to 40%. This resulted in reducing the hydrophobicity (advancing contact angle reduced from 116 to 92°). XPS revealed that the grafted PAA was highly crosslinked. The effects of grafting conditions (dose, monomer concentration, as well as solvent) on the grafting outcome were evaluated. Grafting of tertbutyl acrylate (tBA) was investigated but low graft yields were obtained and this was shown to be unaffected by the solvent used during the grafting process. The mechanical properties of the AA grafted membranes were altered significantly and were dependent on the testing conditions (wet or dry).     

Preparation and characterization of grafting polyacrylamide from PET films by SI‐ATRP via water‐borne system

The grafted homopolymer and comb‐shaped copolymer of polyacrylamide were prepared by combining the self‐assembly of initiator and water‐borne surface‐initiated atom transfer radical polymerization (SI‐ATRP). The structures, composition, properties, and surface morphology of the modified PET films were characterized by FTIR/ATR, X‐ray photoelectron spectroscopy (XPS), contact angle measurement, and scanning electronic microscopy (SEM). The results show that the surface of PET films was covered by equable grafting polymer layer after grafted polyacrylamide (PAM). The amount of grafting polymer increased linearly with the polymerization time added. The GPC date show that the polymerization in the water‐borne medium at lower temperature (50°C) shows better “living” and control. After modified by comb‐shaped copolymer brushes, the modified PET film was completely covered with the second polymer layer (PAM) and water contact angle decreased to 13.6°. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Argon plasma treatment-induced grafting of acrylic acid onto expanded poly(tetrafluoroethylene) membranes

Expanded poly(tetrafluoroethylene) (ePTFE) is used in facial reconstruction surgery. For some specific applications ePTFE is required to interface with the underlying bone. However, ePTFE is classified as bioinert thus limiting integration at the bone-tissue interface. The incorporation of functional groups onto the ePTFE surface was carried out in the current study using argon plasma treatment-induced grafting of acrylic acid (AA) to improve integration. High surface coverage (grafting extent from XPS of up to 90%) was achieved and resulted in high hydrophilicity and high water uptake (up to 470% of the grafted PAA mass). The contribution of species present in the plasma to the incorporation of functional groups onto the ePTFE surface was evaluated with charged species observed to play an equally important role to neutral species in this study. The effects of sample position in the plasma chamber as well as the effect of grafting parameters (plasma power, monomer concentration, and reaction time) on the grafting outcome were evaluated. The mechanical properties of the AA grafted membranes under tensile, compression and nanoindentation were evaluated.     

pH‐responsive permeability of PE‐g‐PMAA membranes

Poly(methacrylic acid) (PMAA) grafted porous PE membranes (PE‐g‐PMAA) were studied. It was found that (1) a wide range of graft yields can be achieved by varying irradiation time (20–240 min) and monomer concentration (0.22M–0.66M), (2) the grafted membrane exhibits reversible permeability response, (3) the membrane shows a maximum permeability response at an intermediate permeant molecular weight due to size exclusion effect, and (4) depending on the graft yield, two types of permeability response can be obtained. These observations are consistent with our earlier study on poly(N‐isopropylacrylamide) (PNIPAAm)–grafted porous polyethylene membranes. In addition, it was observed that the solvent used during grafting may influence the graft location—presumably due to variations in pore wetting. Specifically, compared to water solvent, methanol can increase grafting inside membrane pores, an observation inferred from membrane swelling, thickness measurement, and SEM characterization. Moreover, preferential grafting inside the membrane pores, as affected by increasing methanol content in the grafting solvent, results in lower membrane permeability and a greater pore graft‐controlled type of permeability response. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 76: 778–786, 2000     

Grafting of styrene/maleic anhydride copolymer onto PVDF membrane by supercritical carbon dioxide: Preparation,characterization and biocompatibility

Herein we report the surface modification of poly(vinylidene fluoride) (PVDF) microporous membrane via thermally induced graft copolymerization with maleic anhydride (Man)/styrene (St) in supercritical carbon dioxide (SC CO₂). SC CO₂, as a solvent and carrier agent, could accelerate mass transfer of monomers inside polymer matrixes and then facilitate the graft copolymerization on the surface of the membrane and within membrane pores, which were confirmed by FT-IR/ATR and XPS spectra together with SEM photographs. The effects of SC CO₂ pressure and temperature and the monomer concentration on the graft copolymerization were investigated. The modified PVDF membranes containing from 0 to 7 wt.% of grafted St–Man copolymer (SMA) were prepared and analysed in terms of surface microstructure, composition, hydrophilicity and biocompatibility. Solid-state ¹³C CP/MAS NMR and DSC indicated that the grafted SMA on the PVDF membrane had the alternative sequence structure and formed the different phases in the modified membrane, where the grafted SMA was associated with T_g of 122.8 °C and the PVDF matrix with T_m of 161.2 °C. The static contact angle measurements revealed that remarkable and permanent hydrophilicity was obtained upon grafting SMA. The experiments of BSA adsorption and cell growth also showed that the surface of SMA-based PVDF membrane has excellent biocompatibility.     

低温等离子体处理及丙烯酸接枝改性膨化聚四氟乙烯薄膜

采用He等离子体对膨化聚四氟乙烯(ePTFE)薄膜进行表面亲水处理,并引发接枝丙烯酸单体实现持久亲水改性.实验探究了不同等离子处理工艺和接枝工艺对ePTFE薄膜亲水性能的影响,并利用接触角、X光电子能谱(XPS)进行表征.研究结果表明,等离子体预处理后,ePTFE薄膜表面的接触角由145°降至102°;再接枝丙烯酸单体...     

Preparation and characterization of the copolymers obtained by grafting of monoacryloxyethyl phosphate onto polytetrafluoroethylene membranes and poly(tetrafluoroethylene‐co‐hexafluoropropylene) films

Two fully fluorinated polymers, poly(tetrafluoroethylene) (PTFE) membranes and poly(tetrafluoroethylene‐co‐hexafluoropropylene) (FEP) films, were modified by graft copolymerization with monoacryloxyethyl phosphate (MAEP) in an aqueous solution at ambient temperature using gamma irradiation. The modified membranes were characterized by XPS, FTIR, and phosphate analysis. A correlation between peak heights in the FTIR PAS spectra and the overall grafting yield was found. Neither the surface coverage (as obtained from XPS multiplex scans) nor the overall grafting yield (as obtained from phosphate analysis) showed simple correlations on the monomer concentrations (20–40%) or the irradiation doses (25–150 kGy) within the ranges investigated. Similar surface coverage was achieved on the PTFE membranes and on the FEP films. In contrast, the overall grafting yields were significantly higher for the PTFE membranes than for the FEP films. The high porosity of the PTFE membranes is the most likely explanation for these differences in grafting. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 2550–2556, 2002     

Investigation of radiation‐grafted and radiation‐modified N‐vinyl‐2‐pyrrolidone onto polypropylene film

The radiation‐induced graft copolymerization of N‐vinyl‐2‐pyrrolidone (NVP) onto polypropylene films was investigated using the mutual method. The grafted polymer was modified with prepared α,β‐unsaturated nitrile (Scheme 1 ). The water uptake of the grafted and modified grafted films was found to increase with the degree of grafting. It was observed that the swelling behavior of the modified grafted films with α‐cyano‐β‐phenyl crotononitrile improved more than that of the film grafted and modified grafted with α‐cyano‐β‐(2‐thienyl)crotononitrile or α‐cyano‐β‐(2‐pyridyl)crotononitrile. The modification process for the grafted substrate was confirmed by IR spectroscopy. No significant improvement was observed in thermal stability for the modified grafted films compared to the grafted films. Scanning electron microscopy (SEM) of the grafted and modified grafted membranes heated to 150°C showed change in the structure and morphology. Improvement in the hydrophilicity and morphology of these membranes with carbonitriles may increase the permeability of those membranes for some practical applications.     

Gas-phase photoinduced graft polymerization of acrylic acid onto polyacrylonitrile ultrafiltration membranes

Heterogeneous surface modification of polyacrylonitrile (PAN) ultrafiltration (UF) membranes is realized with UV irradiation-initiated graft polymerization of acrylic acid (AA) from the gas phase onto photoinitiator (benzophenone, BP)-coated samples. In the absence of monomer, PAN functionalization by ketyl radicals dominates after UV excitation of sorbed BP. With AA, graft and total polymer yield increase with BP loading and UV irradiation time. Average molecular weight and distribution of PAA homopolymer—formed in parallel during graft polymerization—are analyzed with gel permeation chromatography. Morphology of PAN-gr-AA UF membranes is checked with scanning electron micrographs (SEMs) and atomic force microscopy. Chemical changes are characterized with FTIR-ATR spectroscopy and SEM/EDX analyses, indicating a pronounced surface selctivity of the graft polymer modification (localized in the upper 5-μm membrane thickness). The amount of grafted PAA systematically reduces membrane permeability and increases dextrane retention, as verified in UF experiments. Photo graft polymer modificationof UF membranes will be applied to adjust membrane performance by controlling surface hydrophilicity and permeability using other monomers and/or further graft polymer functionalization. © 1995 John Wiley & Sons, Inc.     

Surface modification of poly‐L‐lactide by photografting of hydrophilic polymers towards improving its hydrophilicity

Poly‐L ‐lactide (PLLA) has been used to prepare scaffolds to guide tissue regeneration in tissue engineering research. However, one of the limitations to the use of PLLA as an ideal biomaterial is its high hydrophobicity. To improve the hydrophilicity of PLLA, hydrophilic polymers were grafted onto PLLA membrane surfaces through the combination of photooxidization in hydrogen peroxide and subsequent ultraviolet (UV)‐induced grafting copolymerization in the monomer solution. Three kinds of modified PLLA membranes (i.e., PLLA‐g‐polyhydroxyethyl methacrylate, PLLA‐g‐polyacrylamide, and PLLA‐g‐polymethacrylic acid) were obtained, resulting in the more wettable PLLA membranes. The occurrence of the grafting polymerization was confirmed by attenuated total reflectance infrared spectroscopy (ATR‐IR) and X‐ray photoelectron spectroscopy (XPS) analysis. Surface morphology of the modified PLLA membranes was studied by scan electronic microscopy (SEM). © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 2163–2171, 2002     

Surface initiated ATRP of acrylic acid on dopamine‐functionalized AAO membranes

A facile method for surface‐initiated atom transfer radical polymerization (ATRP) on the anodic aluminum oxide (AAO) membranes has been developed. The AAO membrane was firstly functionalized by poly(dopamine), the bromoalkyl initiator was then immobilized on the poly(dopamine) functionalized AAO membrane surface in a two‐step solid‐phase reaction, followed by ATRP of acrylic acid in a aqueous solution. The poly(acrylic acid) (PAAc)‐grafted AAO membranes were characterized by X‐ray photoelectron spectroscopy, fourier transform infrared spectroscopy and scanning electron microscopy. The XPS and FTIR results indicated that PAAc was successfully grafted on the AAO membrane surface. The degree of grafting increases linearly with the increase of monomer concentration, and it reaches a plateau when the reaction time up to 4 h. The results indicate that the thickness of the grafted polymer inside the isocylindrical pores of AAO membranes could be well controlled by changing the reaction time and monomer concentration. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Controlled grafting from poly(vinylidene fluoride) microfiltration membranes via reverse atom transfer radical polymerization and antifouling properties

A reverse atom transfer radical polymerization (RATRP) with benzoyl peroxide (BPO)/CuCl/2,2-bipyridine (Bpy) was applied onto grafting of poly(methyl methacrylate) (PMMA) and poly(poly(ethylene glycol) methyl ether methacrylate) (PPEGMA) from poly(vinylidene fluoride) (PVDF) microfiltration (MF) membrane surfaces, including the pore surfaces. The introduction of peroxide and hydroperoxide groups onto the PVDF membranes was achieved by ultraviolet (UV) irradiation in nitrogen, followed by air exposure. RATRP from UV pretreated hydrophobic PVDF membranes was then performed for attaching well-defined homopolymer. The chemical composition of the modified PVDF membrane surfaces was characterized by attenuated total reflectance (ATR) FT-IR spectroscopy and X-ray photoelectron spectroscopy (XPS). The surface and cross-section morphology of membranes were studied by scanning electron microscopy (SEM). The pore sizes of the pristine PVDF and the PMMA grafted PVDF membranes were measured using micro-image analysis and process software. With increase of graft concentration, the pore size of the modified membranes decreased and became uniform. Kinetic studies of homogeneous (in toluene solution) system revealed a linear increase in molecular weight with the reaction time and narrow molecular weight distribution, indicating that the chain growth from the membrane surface was a “controlled” or “living” grafting process. The introduction of the well-defined PMMA on the PVDF membrane gave rise to hydrophilicity. Protein adsorption and protein solution permeation experiments revealed that the UV pretreated hydrophobic PVDF membrane subjected to surface-initiated RATRP of methyl methacrylate (MMA) and poly(ethylene glycol) methyl ether methacrylate (PEGMA) exhibited good antifouling property.     

Microwave plasma‐initiated grafting of acrylic acid on Celgard 2500 membrane to prepare alkaline battery separators—Characteristics of process and product

A process of plasma‐initiated grafting of acrylic acid on commercial porous polypropylene membrane was studied. The influence of parameters of the plasma (power, gas pressure, time plasma‐sample distance, sample arrangement) and grafting (solvent composition, monomer concentration, time, inhibitor presence) on the degree of grafting, amount of homopolymer produced and surface electrical resistance was determined. A degree of grafting up to 18 mmol/g was obtained, which resulted in sample resistance as low as 30 mΩ cm². The molecular weight of AAc homopolymer that can be assumed as equal to the MW of grafted chains, ranged from 25,000 to 50,000,000 da. SEM and water permeability measurements show that grafting causes filling of the pores, which, however, does not stop K⁺ ions from penetrating the membrane. The performance of nickel‐cadmium cells with acrylic acid grafted membranes as separator is also presented. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Adhesion of polyethylene plates photografted with methacrylic acid and acrylic acid with enzymatically modified chitosan solutions and X‐ray photoelectron spectroscopy analysis of failed surfaces

An investigation was carried out on the application of dilute chitosan solutions modified by a tyrosinase‐catalyzed reaction with 3,4‐dihydroxyphenetylamine (dopamine) to the adhesion of low‐density polyethylene (LDPE) and high‐density polyethylene (HDPE) plates photografted with carboxyl‐group‐containing hydrophilic monomers, such as methacrylic acid (MAA) and acrylic acid (AA). In the case where photografting was carried out at lower monomer concentrations or at lower temperatures, the adhesive strength sharply increased with lower grafted amounts. A sharp increase in the adhesive strength was found to be due to the formation of shorter grafted polymer chains at lower monomer concentrations and/or the restriction of the location of grafting to the outer surface region at lower temperatures. In addition, the adhesive strength also sharply increased at even lower grafted amounts for photografting onto the HDPE plates and/or that of AA because the location of grafting was restricted to the outer surface region. For the AA‐grafted LDPE and HDPE plates, substrate breaking was observed. This was attributed to the coverage of the substrate surfaces with grafted poly(acrylic acid) chains at lower grafted amounts and a high water absorptivity of the grafted layer. X‐ray photoelectron spectroscopy (XPS) analysis of the grafted LDPE plates incubated in a dopamine solution containing tyrosinase suggested that the increase in the adhesive strength was caused by the penetration of enzymatically modified chitosan solutions in the grafted layers and the subsequent reaction of quinone derivatives enzymatically generated with grafted polymer chains. In addition, the surface analysis of the failed surfaces by XPS showed that as the adhesive strength increased, the location of failure was shifted from the interface between the layers mixed with enzymatically modified chitosan materials and grafted polymer chains to the inside the grafted layer containing enzymatically modified chitosan materials. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

聚丙烯/三元乙丙橡胶共混材料表面紫外光接枝聚丙烯酰胺的研究

采用紫外光接枝方法,在聚丙烯（PP）/三元乙丙橡胶（EPDM）共混板材表面接枝聚丙烯酰胺（PAAM）。用衰减全反射傅立叶变换红外光谱、X射线光电子能谱、接触角测试仪和扫描电子显微镜对接枝改性PP板表面进行了表征,并讨论EPDM含量、辐照时间、单体及引发剂用量对接枝量和接触角的影响。结果表明,在共混板材表面成功接枝了PAAM,当EPDM的含量为共混板材的20%时,改性PP板表面接枝量达到0.75 mg/cm^2;接触角从102.5°下降到72.5°;表面自由能从16.6 mN/m增大到48.7 mN/m。     

Influence of the radiation grafting conditions on the cross‐sectional distribution of poly(vinylbenzyl chloride) grafted polymer onto poly(tetrafluoroethylene‐co‐hexafluoropropylene) films

Poly(vinylbenzyl chloride) (PVBC)‐grafted poly(tetrafluoroethylene‐co‐hexafluoropropylene) (FEP) films were prepared as precursors for ion‐exchange membranes with a radiation grafting technique. A scanning electron microscopy–energy dispersive X‐ray spectroscopy (SEM‐EDX) instrument was used to investigate the effects of the radiation grafting conditions on the distribution profiles of the grafts in the FEP‐g‐PVBC films because the properties of the ion‐exchange membranes were largely affected not only by the degree of grafting (DOG) but also by the distribution of the graft chain. These results indicate that the distribution profile of the grafts largely depended on the grafting parameters, such as the solvent, monomer concentration, film thickness, and irradiation dose. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Photograft copolymerization of methyl methacrylate on viscose fiber using titanium(III) chloride–potassium persulfate redox initiator in a limited aqueous system

The graft copolymerization of methyl methacrylate (MMA) onto viscose fibers were studied under photoactive conditions with visible light using titanium(III) chloride—potassium persulfate as redox initiator in a limited aqueous system. Polymerization carried out in the dark at 40 ± 1°C produced little graft copolymer whereas that in the presence of light at 40 ± 1°C produced significant grafting. Percent grafting, percent total conversion, and grafting efficiency (%) were studied by varying time, initiator concentration, monomer concentration, solvent composition, and pH of the medium. High percent grafting (～ 200%), high grafting efficiency (～ 98%), and percent total conversion (～ 47%) were obtained with little homopolymer formation. A suitable mechanism for grafting has been discussed and also the characterization of the grafted fibers were studied by Fourier transform infrared (FTIR) spectroscopy, thermogravimetry and scanning electron microscopy (SEM). © 1992 John Wiley & Sons, Inc.     

Surface modification of low‐density polyethylene films by UV‐induced graft copolymerization with a fluorescent monomer

Surface modification of argon plasma–pretreated low‐density polyethylene (LDPE) film via UV‐induced graft copolymerization with a fluorescent monomer, (pyrenyl)methyl methacrylate (Py)MMA, was carried out. The chemical composition and morphology of the (Py)MMA‐graft‐copolymerized LDPE [(Py)MMA‐g‐LDPE] surfaces were characterized, respectively, by X‐ray photoelectron spectroscopy (XPS) and by atomic force microscopy (AFM). The concentration of the surface‐grafted (Py)MMA polymer increased with Ar plasma pretreatment time and UV graft copolymerization time. The photophysical properties of the (Py)MMA‐g‐LDPE surfaces were measured by fluorescence spectroscopy. After graft copolymerization with the fluorescent monomer, the surface of the LDPE film was found to have incorporated new and unique functionalities. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 1526–1534, 2001