Numerical Investigation of the Effect of Vertical Load on the Lateral Response of Piles

The laboratory and field test data on the response of piles under the combined action of vertical and lateral loads is rather limited. The current practice for design of piles is to consider the vertical and lateral loads independent of each other. This paper presents some results from three-dimensional finite-element analyses that show the significant influence of vertical loads on a pile’s lateral response. The analyses were performed in both homogeneous clayey soils and homogeneous sandy soils. The results have shown that the influence of vertical loads on the lateral response of piles is to significantly increase the capacity in sandy soils and marginally decrease the capacity in clayey soils. In general, it was found that the effect of vertical loads in sandy soils is significant even for long piles, which are as long as 30 times the pile width, while in the case of clayey soils, the effect is not significant for piles beyond a length of 15 times the width of the pile. The design bending moments in the laterally loaded piles were also found to be dependent on the level of vertical load on the piles.     

Lateral Resistance of Short Single Piles and Pile Groups Located Near Slopes

Many transmission towers, high-rise buildings, and bridges are constructed near steep slopes and are supported by large-diameter piles. These structures may be subjected to large lateral loads, such as violent winds and earthquakes. Widely used types of foundations for these structures are pier foundations, which have large diameter with high stiffness. The behavior of a pier foundation subjected to lateral loads is similar to that of a short rigid pile, because both elements seem to fail by rotation developing passive resistance on opposite faces above and below the rotation point, unlike the behavior of a long flexible pile. This paper describes the results of several numerical studies performed with a three-dimensional finite-element method (FEM) of model tests and a prototype test of a laterally loaded short pile and pier foundation located near slopes, respectively. Initially, in this paper, the results of model tests of single piles and pile groups subjected to lateral loading, in homogeneous sand with 30° slopes and horizontal ground were analyzed by the three- dimensional (3D) finite-element (FE) analyses. Furthermore, field tests of a prototype pier foundation subjected to lateral loading on a 30° slope was reported. The FE analyses were conducted to simulate these results. The main purpose of this paper is the validation of the 3D elasto–plastic FEM by comparisons with the experimental data.     

A Robust Macroelement Model for Soil–Pile Interaction under Cyclic Loads

The principal focus of this study is the development of a robust macroelement model for soil–pile interaction under cyclic loads. The model incorporates frictional forces and formation of gaps at the soil–pile interface as well as hysteretic behavior of the soil. The plastic envelope of the soil behavior is modeled via the so-called p–y approach, outlined in American Petroleum Institute’s guidelines for design of foundation piles for offshore platforms. The macroelement is an intuitive assembly of various basic elements, each of which incorporating a particular aspect of the soil–pile interaction. The modular structure of this macroelement allows straightforward adaptation of improved constitutive models for its building blocks. Herein, we focus on large-diameter, cast-in-drilled-hole reinforced concrete piles (piers) that are partially or fully embedded in soil. These types of piles are frequently used as support structures in highway construction. Consequently, the numerical robustness of the interaction model is assessed with parametric studies on pile systems and soil types relevant to this type of construction. Both elastic and inelastic pile behaviors are considered in the parametric studies. The results indicate that the proposed interaction element is numerically robust, and thus, amenable to routine structural analysis.     

Raked Piles—Virtues and Drawbacks

This technical note examines some of the characteristics of behavior of pile groups containing raked piles, via a simplified and hypothetical example. Three cases are examined: (1) a group subjected to vertical and lateral loadings, with no ground movements; (2) a group subjected to vertical and lateral loadings, but with vertical ground movements also acting on the group; and (3) a group subjected to vertical and lateral loadings, but with horizontal ground movements acting on the group. In each case, the effect of pile rake on typical behavioral characteristics (group settlement, lateral deflection and rotation, and pile loads and moments) are examined. It is found that, while the presence of raked piles can provide some advantages when the group is subjected to applied vertical and lateral loadings, especially in relation to a reduction in lateral deflection, some aspects of group behavior may be adversely affected when either vertical or horizontal ground movements act on the group. Thus, caution must be exercised in employing raked piles when such ground movements are expected to occur.     

Applicability of Conventional p-y Relations to the Analysis of Piles in Laterally Spreading Soil

This paper presents a kinematic analysis of a single pile embedded in a laterally spreading layered soil profile and discusses the relevancy of conventional analysis models to this load case. The research encompasses the creation of three-dimensional (3D) finite-element (FE) models using the OpenSees FE analysis platform. These models consider a single pile embedded in a layered soil continuum. Three reinforced concrete pile designs are considered. The piles are modeled using beam-column elements and fiber-section models. The soil continuum is modeled using brick elements and a Drucker-Prager constitutive model. The soil-pile interface is modeled using beam-solid contact elements. The FE models are used to evaluate the response of the soil-pile system to lateral spreading and two alternative lateral load cases. Through the computation of force density-displacement (p-y) curves representative of the soil response, the FE analysis (FEA) results are used to evaluate the adequacy of conventional p-y curve relationships in modeling lateral spreading. It is determined that traditional p-y curves are unsuitable for use in analyses where large pile deformations occur at depth.     

Numerical Analysis of Laterally Loaded 3 × 3 to 7 × 3 Pile Groups in Sands

The coupled bridge foundation-superstructure finite-element code FLPIER was employed to predict the lateral response of the single piles and 3 × 3 to 7 × 3 pile groups founded in both loose and medium dense sands. The p-multiplier factors suggested by McVay et al. for laterally loaded pile groups with multiple pile rows were implemented for the predictions. The soil parameters were obtained through a back-analysis procedure based on single pile test results. The latter, as well as the numerical predictions of both the single and group tests, are presented. It was found that the numerical code FLPIER did an excellent job of predicting the response of both the single piles and the 3 × 3 to 7 × 3 pile groups. The latter involved the predictions of lateral load versus lateral deflection of the group, the shears and bending moments developed in the individual piles, and the distributions of the lateral loads in each pile row, which were all in good agreement with the measured results.     

Seismic Behavior of Batter Piles: Elastic Response

Several aspects of the seismic response of groups containing nonvertical piles are studied, including the lateral pile-head stiffnesses, the “kinematic” pile deformation, and the “inertial” soil-pile-structure response. A key goal is to explore the conditions under which the presence of batter piles is beneficial, indifferent, or detrimental. Parametric analyses are carried out using three-dimensional finite-element modeling, assuming elastic behavior of soil, piles, and superstructure. The model is first used to obtain the lateral stiffnesses of single batter piles and to show that its results converge to the available solutions from the literature. Then, real accelerograms covering a broad range of frequency characteristics are employed as base excitation of simple fixed-head two-pile group configurations, embedded in homogeneous, inhomogeneous, and layered soil profiles, while supporting very tall or very short structures. Five pile inclinations are considered while the corresponding vertical-pile group results serve as reference. It is found that in purely kinematic seismic loading, batter piles tend to confirm their negative reputation, as had also been found recently for a group subjected to static horizontal ground deformation. However, the total (kinematic plus inertial) response of structural systems founded on groups of batter piles offers many reasons for optimism. Batter piles may indeed be beneficial (or detrimental) depending on, among other parameters, the relative size of the overturning moment versus the shear force transmitted onto them from the superstructure.     

Effect of Cracking on the Response of Pile Test under Horizontal Loading

Capacity-based design of structures limits the soil-structure interaction mechanism to the determination of the bearing capacity of a pile group. However, in many cases the criterion for the design of piles to resist lateral loads is not the ultimate lateral capacity but the deflection of the piles. Many procedures exist for estimating the response of single piles and pile groups under lateral loading, ranging from application of empirical relationships and simple closed-form solutions to sophisticated nonlinear numerical procedures. With the aim of investigating the effect of cracking, disregarded by most of the above-mentioned methods, a three-dimensional (3D) nonlinear analysis that accounts for cracking is presented. Response prediction correlates well with the experimental data from a full-scale pile load test. Interesting conclusions have also been drawn regarding the discretization of the computational domain and the combination of 3D numerical nonlinear analysis and the structural beam theory.     

Contact Interface Model for Shallow Foundations Subjected to Combined Cyclic Loading

It has been recognized that the ductility demands on a superstructure might be reduced by allowing rocking behavior and mobilization of the ultimate capacity of shallow foundations during seismic loading. However, the absence of practical reliable foundation modeling techniques to accurately design foundations with the desired capacity and energy dissipation characteristics and concerns about permanent deformations have hindered the use of nonlinear soil–foundation–structure interaction as a designed mechanism for improving performance of structural systems. This paper presents a new “contact interface model” that has been developed to provide nonlinear relations between cyclic loads and displacements of the footing–soil system during combined cyclic loading (vertical, shear, and moment). The rigid footing and the soil beneath the footing in the zone of influence, considered as a macroelement, are modeled by keeping track of the geometry of the soil surface beneath the footing, along with the kinematics of the footing–soil system, interaction diagrams in vertical, shear, and moment space, and the introduction of a parameter, critical contact area ratio (A/Ac); the ratio of footing area (A) to the footing contact area required to support vertical and shear loads (Ac). Several contact interface model simulations were carried out and the model simulations are compared with centrifuge model test results. Using only six user-defined model input parameters, the contact interface model is capable of capturing the essential features (load capacities, stiffness degradation, energy dissipation, and deformations) of shallow foundations subjected to combined cyclic loading.     

Behavior of Step Tapered Bored Piles in Sand under Static Lateral Loading

The behavior of step tapered bored piles in sand, under static lateral loading, was examined by field tests at one site in Kuwait. A total of 14 bored piles including two instrumented piles were installed for lateral loading. The soil profile consists of medium dense sand with weak cementations and no groundwater was encountered in the boreholes. Laboratory tests were carried out to determine the basic soil characteristics and the strength parameters. Both the ultimate lateral capacity and the deflections at applied loads were examined. The results indicate increased lateral load carrying capacity and decreased deflections at different applied loads for the step tapered piles due to the enlargement or strengthening of the upper section of the piles. The advantages of using this type of pile is emphasized including the cost saving resulting from an economical design.     

Simplified Lateral Load Analyses of Fixed-Head Piles and Pile Groups

The characteristic load method (CLM) can be used to estimate lateral deflections and maximum bending moments in single fixed-head piles under lateral load. However, this approach is limited to cases where the lateral load on the pile top is applied at the ground surface. When the pile top is embedded, as in most piles that are capped, the additional embedment results in an increased lateral resistance. A simple approach to account for embedment effects in the CLM is presented for single fixed-head piles. In practice, fixed-head piles are more typically used in groups where the response of an individual pile can be influenced through the adjacent soil by the response of other nearby piles. This pile–soil–pile interaction results in larger deflections and moments in pile groups for the same load per pile compared to single piles. A simplified procedure to estimate group deflections and moments was also developed based on the p-multiplier approach. Group amplification factors are introduced to amplify the single pile deflection and bending moment to reflect pile–soil–pile interaction. The resulting approach lends itself well to simple spreadsheet computations and provides good agreement with other generally accepted analytical tools and with values measured in published lateral load tests on groups of fixed-head piles.     

Analytical Solution for Piles Supporting Combined Lateral Loads

Analytical solutions of normalized maximum deflection and normalized maximum moment for laterally loaded long piles in homogeneous elastoplastic soil under combined loads are presented in this paper. Both the normalized deflection surface and normalized moment surface are continuous and increasing constantly with normalized applied force and moment with various slopes. It shows that the normalized applied force and moment have different contributions to the deflection and moment. In general, the variation of normalized moment surface is relatively moderate compared to normalized maximum deflection. Due to the nonlinear effect, the deflections and moments using superposition approach will be on the unsafe side. The analytical solutions can be used for any elastic materials, any type of soil, and any shapes of pile cross section. Above all, the analytical solutions may be easily applied to calculate the maximum deflection or moment of lateral long piles subject to combined loads accurately using a calculator.     

Nonlinear Efficiency of Bored Pile Group under Lateral Loading

A 3×3 bored pile group consisting of nine cast-in-drilled-hole reinforced concrete shafts and a comparable single-shaft were subjected to reversed cyclic, lateral head loading to investigate group interaction effects across a wide range of lateral displacements. The piles had the same diameter of d = 0.61?m and similar soil conditions; however, various equipment constraints led to two differences: (1) a fixed head (zero rotation) boundary condition for the single pile versus minor pile cap rotation in the vertical plane for the group and (2) shaft longitudinal reinforcement ratios of 1.8% for the single pile and 1% for the group piles. To enable comparisons between the test results, a calibrated model of the single pile (1.8% reinforcement) was developed and used to simulate the response of a single shaft with 1% reinforcement. Additional simulations of the pile group were performed to evaluate the effects of cap rotation on group response. By comparing the simulated responses for common conditions, i.e., 1% reinforcing ratio and zero head rotation, group efficiencies were found to range from unity at lateral displacements <0.004×d to 0.8 at small displacements ～ 0.01–0.02×d and up to 0.9 at failure (displacements >0.04×d). Hence, we find that group efficiency depends on the level of nonlinearity in the foundation system. The general group efficiency, although not its displacement-dependence, is captured by p-multipliers in the literature for reinforced concrete, fixed-head piles.     

Wedge Failure Analysis of Soil Resistance on Laterally Loaded Piles in Clay

A fundamental study of pile-soil systems subjected to lateral loads in clay soil was conducted by using experimental tests and a lateral load-transfer approach. The emphasis was on an improved wedge failure model developed by considering three-dimensional combination forces and a new hyperbolic p-y criterion. A framework for determining the p-y curve on the basis of both theoretical analysis and experimental load test results is proposed. The proposed p-y method is shown to be capable of predicting the behavior of a large-diameter pile under lateral loading. The proposed p-y curves with an improved wedge model are more appropriate and realistic for representing a pile-soil interaction for laterally loaded piles in clay than the existing p-y method.     

Three-Dimensional Analysis of Performance of Laterally Loaded Sleeved Piles in Sloping Ground

Development of urban cities in hilly terrain often involves the construction of high-rise buildings supported by large diameter piles on steep cut slopes. Under lateral loads, the piles may induce slope failure, particularly at shallow depths. To minimize the transfer of lateral load from the buildings to the shallow depths of the slope, an annulus of compressible material, referred to as sleeving, is usually constructed between the piles and the adjacent soil. However, the influence of the sleeving on the pile performance in a sloping ground is not fully studied and understood. To investigate the influence, a 3D numerical analysis of sleeved and unsleeved piles on a cut slope is described in this paper. The influences of relative soil stiffness on the response of sleeved piles are also examined. The load transfer from the laterally loaded sleeved pile to the sloping ground is primarily through a shear load transfer mechanism in the vertical plane. Under small lateral loads, the sleeving can lead to a significant reduction in subgrade reaction on the sleeved pile segment and may considerably increase the pile deflection and bending moments. Under large lateral loads, the influence of the sleeving on pile performance appears to diminish because of the widespread plastic zones developed around the pile.     

Lateral Force Induced by Rectangular Surcharge Loads on a Cross-Anisotropic Backfill

This article presents approximate but analytical-based solutions for computing the lateral force (force per unit length) and centroid location induced by horizontal and vertical surcharge surface loads resting on a cross-anisotropic backfill. The surcharge loading types include: point load, finite line load, and uniform rectangular area load. The planes of cross-anisotropy are assumed to be parallel to the ground surface of the backfill. Although the presented solutions have never been proposed in existing literature, they can be derived by integrating the lateral stress solutions recently addressed by the author. It is clear that the type and degree of geomaterial anisotropy, loading distances from the retaining wall, and loading types significantly influence the derived solutions. An example is given for practical applications to illustrate the type and degree of soil anisotropy, as well as the loading types on the lateral force and centroid location in the isotropic/cross-anisotropic backfills caused by the horizontal and vertical uniform rectangular area loads. The results show that both the lateral force and centroid location in a cross-anisotropic backfill are quite different from those in an isotropic one. The derived solutions can be added to other lateral pressures, such as earth or water pressure, which are necessary in the stability and structural analysis of a retaining wall. In addition, they can be utilized to simulate more realistic conditions than the surcharge strip loading in geotechnical engineering for the backfill geomaterials are cross-anisotropic.     

Response of Laterally Loaded Large-Diameter Bored Pile Groups

This paper presents results of full-scale lateral load tests of one single pile and three pile groups in Hong Kong. The test piles, which are embedded in superficial deposits and decomposed rocks, are 1.5 m in diameter and approximately 30 m long. The large-diameter bored pile groups consist of one two-pile group at 6 D (D = pile diameter) spacing and one two-pile and one three-pile group at 3 D spacing. This paper aims to investigate the nonlinear response of laterally loaded large-diameter bored pile groups and to study design parameters for large-diameter bored piles associated with the p-y method using a 3 D finite-element program, FLPIER. Predictions using soil parameters based on published correlations and back-analysis of the single-pile load test are compared. It is found that a simple hyperbolic representation of load-deflection curves provides an objective means to determine ultimate lateral load capacity, which is comparable with the calculated values based on Broms' theory. Lateral deflections of bored pile groups predicted using the values of the constant of horizontal subgrade reaction, suggested by Elson and obtained from back-analysis of the single pile load test, are generally in good agreement with the measurements, especially at low loads.     

Field Investigation of a Sandwich Plate System Bridge Deck

This paper presents the results of a live-load test of the Shenley Bridge, the first bridge application of the sandwich plate system technology in North America. The investigation focused on the evaluation of in-service performance including lateral load distribution behavior and dynamic load allowance. Real-time midspan deflections and strain values were measured under both static and dynamic conditions and under various loading configurations to assess the in-service performance. Distribution factors were determined for interior and exterior girders subjected to single and paired truck loadings. In addition, dynamic load allowance was determined from a comparison of the bridge’s response under static conditions to the response under dynamic conditions. From a comparison of measured results to AASHTO LRFD, AASHTO standard, and CHBDC provisions, it was determined that the current provisions tend to produce conservative predictions for lateral load distribution, but can be unconservative for dynamic load allowance. As a result of the testing program containing a single field test, a finite-element model was also used for determination of lateral load distribution and yielded predictions similar to measured results. The results from the finite-element models were often less conservative than the code provisions.     

Performance of Conservatories under Wind and Snow Loads

Wind and snow loads are the governing load cases for the design of conservatories. The performance of conservatories under these loads determines to a great extent the reliability and serviceability of these structures. This paper presents a study that evaluates the performance of several conservatory designs under wind and snow loads calculated according to the ASCE 7–05 standard. A full-scale model of one common conservatory design was constructed and tested under extreme wind and snow conditions. The model was able to withstand the applied loads without any signs of damage or partial failures. Measured deformations were used to calibrate the three-dimensional computer model developed to simulate the actual structure. Several other computer models were developed to structurally analyze different conservatory designs and estimate their vertical and lateral deflections. The design of critical sections in each model was checked using the load and resistance factor design of wood structures. The study concluded that the design of these conservatories is adequate and their performance is satisfactory under wind and snow loading conditions.     

Lateral Resistance of Single Pile Located Near Geosynthetic Reinforced Slope

An extensive program of laboratory tests was carried out to study the effect of reinforcing an earth slope on the lateral behavior of a single vertical pile located near the slope. Layers of geogrid were used to reinforce a sandy slope of 1 (V):1.5 (H) made with sands of three different unit weights representing dense, medium dense, and loose relative densities. Several configurations of geogrid reinforcement with different numbers of layers, vertical spacing, and length were investigated. The experimental program also included studies of the location of pile relative to the slope crest, relative density of sand, and embedment length of pile. The results indicate that stabilizing a soil slope has a significant benefit of improving the lateral load resistance of a vertical pile. The improvement in pile lateral load was found to be strongly dependent on the number of geogrid layers, layer size, and relative density of the sand. It was also found that soil reinforcement is more effective for piles located closer to the slope crest. Based on test results, critical values are discussed and recommended.