Alcohol-soluble polyfluorenes containing dibenzothiophene-S,S-dioxide segments for cathode interfacial layer in PLEDs and PSCs

A series of alcohol-soluble amino-functionalized polyfluorene derivatives (PF-N-S, PF-N-SC8 and PF-N-SOC8) comprising various ratios of dibenzothiophene-S,S-dioxide segments (S/SC8/SOC8) in the main chains, respectively, were synthesized and utilized as cathode interfacial layer (CIL) in polymer light-emitting diodes (PLEDs) and polymer solar cells (PSCs) with high-work-function Al (or Au) electrode. The polymers possess LUMO/HOMO levels at −2.78 to −3.53 eV/−5.69 to −6.32 eV. Multilayer PLEDs and PSCs with device configurations of ITO/PEDOT:PSS (40 nm)/P-PPV or PFO-DBT35:PCBM = 1:2 (80 nm)/CIL (3–15 nm)/Al (or Au) (100 nm) were fabricated. The PF-N-S-10/Al (or Au) cathode PLEDs displayed maximum luminous efficiency of 24.4 cd A⁻¹ (or 11.9 cd A⁻¹), significantly higher than bare Al (or Au) cathode device, exceeding well-known Ba/Al and poly[(9,9-bis(3′-(N,N-dimethylamino)propyl)-2,7-fluorene)-alt-2,7-(9,9-dioctylfluorene)] (PFN)/Al (or PFN/Au) cathode devices. The enhanced open-circuit voltages (V_ocs), electron reflux and reduced work functions clarify that the electron injection barrier from the Al (or Au) electrode can be lowered by inserting the polymers as CIL. The resulted PSCs also show device performances exceeding Al and PFN/Al cathode devices. The results indicate that PF-N-S, PF-N-SC8 and PF-N-SOC8 are excellent CIL materials for PLEDs and PSCs with high-work-function Al or Au electrode.     

Potassium-neutralized perylene derivative (K4PTC) and rGO-K4PTC composite as effective and inexpensive electron transport layers for polymer solar cells

The polymer solar cell (PSC) with Ca/Al electrode always suffers from low stability mainly due to the incorporation of oxygen and moisture-sensitive Ca electron-transport interlayer (ETL). To alleviate this problem, air-stable alternatives to Ca ETL are highly desired. Herein, we report two solution-processable, air-stable, effective and inexpensive ETLs based on potassium-neutralized perylene tetracarboxylic derivative (K₄PTC) and its rGO composite (rGO-K₄PTC), respectively. These ETL materials were facilely prepared and characterized by means of UV-vis, FL, FTIR, XPS and UPS. Importantly, both ETLs exhibited a low work function (WF) of 4.0 eV, which well matches the LUMO level of fullerene acceptors and allows their use as ETL in PSCs. As a result, the P3HT and PTB7-th-based devices with respective ETL remarkably outperformed those without ETL yielding increases of ∼35% in power conversion efficiencies (PCEs), which indicates good electron-transporting capabilities of K₄PTC and rGO-K₄PTC interlayers. The high-performance PSCs with the ETL gave average PCEs of 6.17–6.18% (for PTB7-th:PC₆₁BM-based devices) and 7.26% (for PTB7-th:PC₇₁BM-based devices), respectively, fairly comparable to those of Ca/Al devices (6.50% and 7.50%). Furthermore, the rGO-K₄PTC device exhibited stability higher than that of the K₄PTC device probably due to the fact that the rGO-K₄PTC layer can provide more efficient protection for the active layer against degradation. Thus, rGO-K₄PTC layer might be more suitable for real applications as compared to the K₄PTC layer.     

Ionic liquids with variable cations as cathode interlayer for conventional polymer solar cells

Interfacial layer materials have been demonstrated to be crucial for high-efficiency polymer solar cells (PSCs). In this work, we use ionic liquid (IL) as cathode interfacial layer (CIL) for highly efficient conventional PSCs (c-PSCs) and investigate functions of ILs with different cations and substituents. Employing IL as the CIL, PBDTTT-C:PC₇₁BM-based c-PSC affords a power conversion efficiency (PCE) of 7.29%, much higher than that without the CIL (2.78%) and that with Ca/Al electrode (6.18%). When the photoactive layer is a PTB7-Th:PC₇₁BM blend, a higher PCE of 8.67% can be obtained. The ILs reduce the energy barrier due to the existence of interfacial dipole in c-PSCs, leading to increased electron and hole mobilities, reduced series resistance and enhanced contact at the cathode interface. Meanwhile, alkyl chain-substituted ILs offer higher fill factor and PCE than aromatic groups-substituted analogue, which is mainly contributed to more balanced electron and hole mobilities. This work suggests that the ILs are qualified candidates as the CIL for c-PSCs and that one should take the substitution effect into account when choosing a CIL from a large library of materials.     

Efficiency enhancement of polymer solar cells by applying an alcohol-soluble fullerene aminoethanol derivative as a cathode buffer layer

Cathode buffer layer (CBL) introduced between the active layer and cathode is crucial for selectively transporting electrons and blocking holes for polymer solar cells (PSCs). Calcium (Ca) is the most commonly used CBL in conventional-structure bulk heterojunction (BHJ) PSC devices, but is prone to oxidation due to its high reactivity, inhibiting its practical applications. Herein, we applied an alcohol-soluble fullerene aminoethanol derivative (C₆₀-ETA) as an efficient CBL surpassing Ca in conventional-structure BHJ-PSC devices, leading to obvious efficiency enhancement with the best power conversion efficiency (PCE) reaching 9.66%. C₆₀-ETA CBL was applied in PSC devices based on three different photoactive layer systems, including poly[4,8-bis(5-(2-ethylhexyl)thiophen-2-yl)-benzo[1,2-b:4,5-b′]dithiophene-co-3-fluorothieno[3,4-b]thiophene-2-carboxylate]:[6,6]-phenyl C₇₁-butyric acid methyl ester (PTB7-Th:PC₇₁BM), polythieno[3,4-b]thiophene-co-benzodithiophene (PTB7):PC₇₁BM and poly(4,8-bis-alkyloxybenzo(l,2-b:4,5-b′)dithiophene-2,6-diylalt-(alkylthieno(3,4-b)thiophene-2-carboxylate)-2,6-diyl) (PBDTTT-C):PC₇₁BM, affording the best PCE of 9.66%, 8.51% and 7.19%, respectively, which are all higher than those of the corresponding devices based on the commonly used Ca CBL. The mechanism of efficiency enhancement of C₆₀-ETA CBL relative to Ca is studied, revealing that C₆₀-ETA CBL may induce improvements on both the interfacial contact between the active layer/cathode and electron transport, facilitating electron extraction by the Al cathode, and consequently leading to the increase of short-circuit current density (J_sc), which contributes primarily to the PCE improvement.     

Polymer Solar Cells Exceeding 10% Efficiency Enabled via a Facile Star‐Shaped Molecular Cathode Interlayer with Variable Counterions

A series of star‐shaped small molecular cathode interlayer materials are synthesized for PTB7:PC₇₁BM based polymer solar cells (PSCs), comprising neutral amino groups, quaternary ammonium ions, amino N‐oxides, and sulfobetaine ions as pendant polar functionalities, respectively. For the first time, the effect of these different pendant functional groups with or without mobile counterions on the cells' photovoltaic properties is investigated in detail. A large improvement in device performance is observed by inserting these cathode interfacial layers (CILs) between the PTB7:PC₇₁BM active layer and the Al electrode. The CILs could effectively lower the work function of the Al cathode, increase the built‐in potential, and decrease the series resistance of the related PSCs. poly(9,9‐dioctylfluorene‐co‐N‐[4‐(3‐methyl‐propyl)]‐diphenylamine) with pendant quaternary ammonium ions shows the best cathode modification ability, giving rise to the highest power conversion efficiency of 10.1%, even better than that of the typical poly[(9,9‐bis(3′‐(N,N‐dimethylamino)propyl)‐2,7‐fluorene)‐alt‐2,7‐(9,9‐dioctylfluorene)] based device. The design strategy and structure–property relationships concluded in this work will be helpful to develop more efficient cathode interface materials for high‐performance PSCs in the future.     

Carbon Nanotube Based Inverted Flexible Perovskite Solar Cells with All‐Inorganic Charge Contacts

Organolead halide perovskite solar cells (PSC) are arising as promising candidates for next‐generation renewable energy conversion devices. Currently, inverted PSCs typically employ expensive organic semiconductor as electron transport material and thermally deposited metal as cathode (such as Ag, Au, or Al), which are incompatible with their large‐scale production. Moreover, the use of metal cathode also limits the long‐term device stability under normal operation conditions. Herein, a novel inverted PSC employs a SnO₂‐coated carbon nanotube (SnO₂@CSCNT) film as cathode in both rigid and flexible substrates (substrate/NiO‐perovskite/Al₂O₃‐perovskite/SnO₂@CSCNT‐perovskite). Inverted PSCs with SnO₂@CSCNT cathode exhibit considerable enhancement in photovoltaic performance in comparison with the devices without SnO₂ coating owing to the significantly reduced charge recombination. As a result, a power conversion efficiency of 14.3% can be obtained on rigid substrates while the flexible ones achieve 10.5% efficiency. More importantly, SnO₂@CSCNT‐based inverted PSCs exhibit significantly improved stability compared to the standard inverted devices made with silver cathode, retaining over 88% of their original efficiencies after 550 h of full light soaking or thermal stress. The results indicate that SnO₂@CSCNT is a promising cathode material for long‐term device operation and pave the way toward realistic commercialization of flexible PSCs.     

High performance thermal-treatment-free tandem polymer solar cells with high fill factors

It is an effective way to enhance device performance of polymer solar cells (PSCs) by using a tandem structure that combines two or more solar cells. For tandem PSCs, the buffer layer plays an important role in determining the device performance. The most commonly used buffer layers, such as PEDOT:PSS, TiO_x, and ZnO, need thermal treatments that are not beneficial for reducing the fabrication complexity and cost of tandem PSCs. It is necessary to develop tandem PSCs fabricated by a thermal-treatment-free process. In this paper, we report high performance thermal-treatment-free tandem PSCs by developing PFN as buffer layers for both subcells. A power conversion efficiency (PCE) of 10.50% and a high fill factor of 72.44% were achieved by stacking two identical PTB7:PC₇₁BM subcells. When adopting a rear PTB7-Th:PC₇₁BM subcell, the highest PCE of 10.79% was further obtained for the tandem devices. The thermal-treatment-free process is especially applicable to flexible devices, in which plastic substrates are usually used.     

Zwitterionic ammonium and neutral amino molecules as cathode interlayer for inverted polymer solar cells

Cathode interlayer is essential to inverted bulk heterojunction polymer solar cells (PSCs). A series of zwitterionic ammonium and neutral amino organic molecules are introduced into inverted PSCs as cathode interlayer and power conversion efficiency (PCE) as high as 8.07% is demonstrated. Compared to the devices without interlayer, all the devices exhibit significant improvements of the device parameters by reducing the work function of indium tin oxide (ITO) cathode. It is striking that the devices with neutral amino molecules as interlayer exhibit remarkably higher PCEs than the devices with zwitterionic ammonium molecules as interlayer. We attribute the improved performance to the better photoactive morphology induced by the hydrophobic properties of the neutral amino derivatives through research of ultraviolet photoelectron spectroscopy, atomic force microscopy, and contact angle measurements. Interestingly, the PCEs of the inverted PSCs with cathode interlayer are positively correlated with the hydrophobic properties of the interlayer materials, since devices with neutral amino molecules or molecules with a more hydrophobic alkyl pendant (piperidine) as interlayer exhibit higher PCEs. These results pave the way to the design of effective cathode interlayer materials.     

All‐Carbon‐Electrode‐Based Endurable Flexible Perovskite Solar Cells

Endured, low‐cost, and high‐performance flexible perovskite solar cells (PSCs) featuring lightweight and mechanical flexibility have attracted tremendous attention for portable power source applications. However, flexible PSCs typically use expensive and fragile indium–tin oxide as transparent anode and high‐vacuum processed noble metal as cathode, resulting in dramatic performance degradation after continuous bending or thermal stress. Here, all‐carbon‐electrode‐based flexible PSCs are fabricated employing graphene as transparent anode and carbon nanotubes as cathode. All‐carbon‐electrode‐based flexible devices with and without spiro‐OMeTAD (2,2′,7,7′‐tetrakis‐(N,N‐di‐p‐methoxyphenylamine)‐9,9′‐spirobifluorene) hole conductor achieve power conversion efficiencies (PCEs) of 11.9% and 8.4%, respectively. The flexible carbon‐electrode‐based solar cells demonstrate superior robustness against mechanical deformation in comparison with their counterparts fabricated on flexible indium–tin oxide substrates. Moreover, all carbon‐electrode‐based flexible PSCs also show significantly enhanced stability compared to the flexible devices with gold and silver cathodes under continuous light soaking or 60 °C thermal stress in air, retaining over 90% of their original PCEs after 1000 h. The promising durability and stability highlight that flexible PSCs are fully compatible with carbon materials and pave the way toward the realization of rollable and low‐cost flexible perovskite photovoltaic devices.     

A two-dimension-conjugated small molecule for efficient ternary organic solar cells

Ternary organic solar cells (OSCs) are burgeoning as one of the effective strategies to achieve high power conversion efficiencies (PCEs) by incorporating a third component with a complementary absorption into the binary blends. In this study, we presented a new two-dimension-conjugated small molecule denoted by DR3TBDTTVT, which alone gave rise to a best PCE of 5.71% with acceptor PC₇₁BM as active layer. Given the complementary absorption with PTB7-Th, DR3TBDTTVT was doped into (PTB7-Th:PC₇₁BM)-based binary blends, and ternary OSCs were developed. The ternary OSCs with 10 wt% of DR3TBDTTVT displayed improved hole-mobility, reduced device resistance and better phase separation of active layer, thus leading to an impressive PCE of 7.77% with open-circuit voltage of 0.77 V, short-circuit density of 14.52 mA cm⁻² and fill factor of 70.3%. Ternary OSCs well make up for the light-harvesting insufficiency of binary OSCs, and this research provides a new material for the improvement of PCEs for single-junction OSCs.     

Novel brominated compounds using in binary additives based organic solar cells to achieve high efficiency over 10.3%

Solvent additives have been considered as a simple and efficient method to increase the performance of bulk-heterojunction (BHJ) organic solar cells, in which, the morphology of the active layer could obtain further improvements by using the binary solvent additives. In this paper, a series of brominated compounds, 1-Bromo-4-butylbenzene (Brbb), 1-Bromo-4-n-hexylbenzene (Brbh) and 1-Bromo-4-n-octylbenzene (Brbo), have been respectively incorporated with 1, 8-diiodooctane (DIO) and regarded as binary solvent additives to fabricate highly efficient bulk heterojunction (BHJ) organic solar cells (OSCs). Compared with the BHJ film based on single additive, the binary additives contained BHJ film shows increased optical absorption, efficient charge transport and better active layer morphology, leading to an enhancement of short-circuit current (J_SC) together with a higher achieved fill factor (FF). The conventional BHJ device using PTB7: PC₇₁BM or PTB7-th: PC₇₁BM with the binary solvent additives exhibit enhanced PCE of 8.13% and 10.31%, respectively, which is much higher than that of single additive based devices (7.04% for PTB7 and 8.73% for PTB7-th). The optimized performance of BHJ devices indicates that these brominated compounds are promising additives to improve device efficiency.     

Effect of PEI cathode interlayer on work function and interface resistance of ITO electrode in the inverted polymer solar cells

In this paper, we investigated the effect of PEI cathode interlayer on the work function and the interface resistance of ITO electrode in the inverted polymer solar cells (PSCs) based on PBDTTT-C-T:PC₇₀BM. It is found that a very thin layer of PEI (⩽5.5 nm), either linear PEI (l-PEI) or branched PEI (b-PEI) with different molecular weights, is enough to lower the work function of the ITO electrode and to enhance the photovoltaic performance of the devices. The champion power conversion efficiency (PCE) of the devices with the PEI cathode interlayer is 7.84%, more than doubled of that without the interlayer. However, a thicker PEI interlayer (⩾10 nm) results in abrupt decrease of the PCEs due to the increase of the resistance. Interestingly, for the thicker interlayers, the l-PEI shows high photovoltaic performance than that of b-PEI, which can also be explained by their difference in the resistances. This work supplies an insight into the function of PEI cathode interlayer on improving the work function and resistance of ITO electrode in the inverted PSCs, and provides some instructions on the future design of interlayer materials in PSCs.     

Polymer‐Modified ZnO Nanoparticles as Electron Transport Layer for Polymer‐Based Solar Cells

The optimization of interfacial layer plays a critical role in the ultimate use of polymer‐based solar cells (PSCs). By introducing an insulating polymer, polystyrene (PS), into the ZnO nanoparticles (NPs) with large particle size, an electron transport layer (ETL) with a thickness of more than 130 nm is produced. The doping of PS not only improves the film quality of ZnO NPs to generate a denser, smoother, and more uniform ETL, but also increases the contact properties between the hydrophilic ZnO and hydrophobic active layer. In comparison to control devices, the power conversion efficiencies (PCEs), short circuit current densities, and fill factors of PSCs with the PS‐modified ETL for a typical fullerene system PTB7‐Th:PC₇₁BM and, also, a nonfullerene system PBDB‐T:ITIC are increased, with PCEs from 8.49% to 9.54% and 10.03% to 11.05%, respectively. The reproducibility, mechanical endurance, and ambient stability of the PSCs with the PS‐modified ZnO NP ETL are significantly improved. The combination of the insulating polymer and ZnO NPs provides a simple, low‐cost way to realize the commercialization of high performance, flexible PSCs.     

Non-fullerene organic solar cells with 7% efficiency and excellent air stability through morphological and interfacial engineering

We report on the fabrication of the poly{[4,8-bis[(2-ethylhexyl)oxy]benzo[1,2-b:4,5-b′]dithiophene-2,6-diyl][3-fluoro-2-[(2-ethylhexyl)carbonyl]thieno[3,4-b]thiophenediyl]} (PTB7) and poly{[N,N-9-bis(2-octyldodecyl)- naphthalene-1,4,5,8-bis(dicarboximide)-2,6-diyl]-alt-5,59-(2,29-bithiophene)}(P(NDI2OD-T2)) active layer combination employing air brush spray coating technique in 2-methyl anisole. Optical absorption characteristics of the blend layer were examined utilizing UV–visible spectra in the wavelength sweep varying from 300 to 900 nm. Atomic force microscopy was utilized to analyze the surface characteristics of the fabricated active layer. Under the radiance of simulated solar light with 100 mW cm⁻² (AM 1.5G), the current density voltage (J-V) characteristics were determined by employing a solar simulator. Fullerene-free organic solar cells were build using a combination of P(NDI2OD-T2) acceptor and a polymer donor PTB7 with SnO₂ acting as an interlayer, which showed power conversion efficiency (PCEs) of more than 7.0%, which is considered as the best PCEs been reported for the chosen donor and the acceptor. The device is extremely stable, holding 75% of its unique effectiveness subsequent to being put away in air for 72 days even without encapsulation. These outcomes demonstrate that the spray-coated film is a feasible contrasting option to the vacuum-deposited ITO film in terms of cost for mass production and for roll-to-roll based organic solar cells.     

High‐Performance Colorful Semitransparent Polymer Solar Cells with Ultrathin Hybrid‐Metal Electrodes and Fine‐Tuned Dielectric Mirrors

Polymer solar cells (PSCs) possess the unique features of semitransparency and coloration, which make them potential candidates for applications in aesthetic windows. Here, the authors fabricate inverted semitransparent PSCs with high‐quality hybrid Au/Ag transparent top electrodes and fine‐tuned dielectric mirrors (DMs). It is demonstrated that the device color can be tailored and the light harvesting in the PSCs can be enhanced by matching the bandgap of the polymer donors in the active layer with the specifically designed maximum‐reflection‐center‐wavelengths of the DMs. A detailed chromaticity analysis of the semitransparent PSCs from both bottom and top (mirror) views is also carried out. Furthermore, the inverted semitransparent PSCs based on PTB7‐Th:PC₇₁BM with six pairs of DMs demonstrate a maximum power conversion efficiency (PCE) of 7.0% with an average visible transmittance (AVT) of 12.2%. This efficiency is one of the highest reported for semitransparent PSCs, corresponding to 81.4% of the PCE from opaque counterpart devices. The device design and processing method are also successfully adapted to a flexible substrate, resulting in a device with a competitive PCE of 6.4% with an AVT of 11.5%. To the best of our knowledge, this PCE value is the highest value reported for a flexible semitransparent PSC.     

A Versatile Buffer Layer for Polymer Solar Cells: Rendering Surface Potential by Regulating Dipole

Spin‐coated film of poly(vinylidenefluoride‐hexafluoropropylene) (P(VDF‐HFP)) acts as a cathode/anode buffer layer in polymer solar cells (PSCs) with conventional/inverted device structures. Such devices show optimized performances comparable with the controlled device, making P(VDF‐HFP) a good substitute for LiF/MoO₃ as a cathode/anode buffer layer. Ultraviolet photoelectron spectroscopy (UPS) and Kelvin force microscope (KFM) measurements show that increased surface potential of active layers improves cathode contact. In piezoresponse force microscopy (PFM) measurement, P(VDF‐HFP) responds to applied bias in phase curve, showing tunable dipole. This tunable dipole renders surface potential under applied bias. As a result, open‐circuit voltage of devices alters instantly with poling voltage. Moreover, positive poling of P(VDF‐HFP) together with simultaneous oxidation of Ag gradually improves performance of inverted structure device. Integer charge transfer (ICT) model elucidates improved electrode contacts by dipole tuning, varying surface potential and vacuum level shift. Understanding the function of dipole makes P(VDF‐HFP) a promising and versatile buffer layer for PSCs.     

Wide Bandgap Molecular Acceptors with a Truxene Core for Efficient Nonfullerene Polymer Solar Cells: Linkage Position on Molecular Configuration and Photovoltaic Properties

Two wide bandgap star‐shaped small molecular acceptors, para‐TrBRCN and meta‐TrBRCN , are synthesized for efficient nonfullerene polymer solar cells (PSCs). The tiny structural variation by just changing the linkage positions affects largely the inherent properties of the resulting molecules. Both molecules have a nonplanar 3D structure, which can prevent the excessively aggregation to realize the optimized morphology and ideal domain size in their active blends. Compared to para‐TrBRCN , meta‐TrBRCN exhibits the smaller distortions between the truxene skeleton and the benzothiadiazole units, which would also lead to the enhanced π–π stacking and charge transfer. When blending with PTB7‐Th, high power conversion efficiencies (PCEs) of 10.15% and 8.28% are obtained for meta‐TrBRCN and para‐TrBRCN devices, respectively. To make up the weak absorption of above binary active blend in the longer wavelength region and increase the whole device performance further, low bandgap 3,9‐bis(2‐methylene‐(3‐(1,1‐dicyanomethylene)‐indanone)‐5,5,11,11‐tetrakis(4‐hexylthienyl)‐dithieno[2,3‐d:2′,3′‐d′]‐s‐indaceno[1,2‐b:5,6‐b′]‐dithiophene (ITIC‐Th) is added as the second acceptor material to fabricate ternary blend PSCs. After adding 20 wt% of ITIC‐Th, the resulting devices exhibit the well‐balanced optical absorption and fine‐tuned morphology, giving rise to the significantly improved PCE of 11.40% with much higher J _sc of 18.25 mA cm^?2 and fill factor of 70.2%.     

Lending Triarylphosphine Oxide to Phenanthroline: a Facile Approach to High‐Performance Organic Small‐Molecule Cathode Interfacial Material for Organic Photovoltaics utilizing Air‐Stable Cathodes

Cathode interfacial material (CIM) is critical to improving the power conversion efficiency (PCE) and long‐term stability of an organic photovoltaic cell that utilizes a high work function cathode. In this contribution, a novel CIM is reported through an effective and yet simple combination of triarylphosphine oxide with a 1,10‐phenanthrolinyl unit. The resulting CIM possesses easy synthesis and purification, a high T _g of 116 °C and attractive electron‐transport properties. The characterization of photovoltaic devices involving Ag or Al cathodes shows that this thermally deposited interlayer can considerably improve the PCE, due largely to a simultaneous increase in V _oc and FF relative to the reference devices without a CIM. Notably, a PCE of 7.51% is obtained for the CIM/Ag device utilizing the active layer PTB7:PC₇₁BM, which far exceeds that of the reference Ag device and compares well to that of the Ca/Al device. The PCE is further increased to 8.56% for the CIM/Al device (with J _sc = 16.81 mA cm^?2, V _oc = 0.75 V, FF = 0.68). Ultraviolet photoemission spectroscopy studies reveal that this promising CIM can significantly lower the work function of the Ag metal as well as ITO and HOPG, and facilitate electron extraction in OPV devices.     

Copolymers based on thiazolothiazole-dithienosilole as hole-transporting materials for high efficient perovskite solar cells

The interlayers, including hole transporting layer (HTL) and electron transporting layer (ETL), segregating photoactive layer and the electrodes play an important role in charge extraction and transportation in perovskite solar cells (pero-SCs). Two novel copolymers, PDTSTTz and PDTSTTz-4, for the first time were applied as HTL in the n-i-p type pero-SCs, with the device structure of ITO/compact TiO₂/CH₃NH₃PbI_3-xCl_x/HTL/MoO₃/Ag. The highest occupied molecular orbitals (HOMO) levels of PDTSTTz and PDTSTTz-4 exhibit a suitable band alignment with the valence band edge of the perovskite. Both of them lead to improved device performances compared with reference pero-SCs based on P3HT as HTL. To further balance the charge extraction and the diffusion length of charge carriers, pristine C₆₀ was introduced at the cathode side of the pero-SCs, working together with TiO₂ as ETL. With insertion of both the HTL and ETL, the performance of pero-SCs was greatly enhanced. The optimized devices exhibited impressive PCEs of 14.4% and 15.8% for devices based on PDTSTTz and PDTSTTz-4. The improved performance is attributed to better light harvest ability, decreased interface resistance and faster decay time due to the introduction of the interlayers.     

Manipulating backbone structure with various conjugated spacers to enhance photovoltaic performance of D–A-type two-dimensional copolymers

A class of low band-gap two-dimensional conjugated polymers of PBDTT-FQ, PBDTT-TQ, PBDTT-BTQ and PBDTT-TTQ was designed and synthesized, which contains the same di(alkylthiophene)-substituted benzo[1,2-b:4,5-b′]dithiophene (BDTT) and 6,7-difluoroquinoxaline (Q) units, as well as various conjugated spacers of furan, thiophene, bithiophene and thieno[3,2-b]thiophene in the main chain. Significant effect of the varied spacers between the BDTT and Q units on the thermal, optical, electrochemical and photovoltaic properties was investigated and observed for these two-dimensional copolymers in the polymer solar cells. The maximum power conversion efficiency of 5.9% with a short circuit current of 13.7 mA/cm² and a fill factor of 0.56 was obtained for the PBDTT-TQ with thiophene spacer in the bulk hetero-junction PSCs using [6,6]-phenyl-C₇₁-butyric acid methyl ester as acceptor.