Effect of inserting a buffer layer on the characteristics of transparent conducting impurity-doped ZnO thin films prepared by dc magnetron sputtering

In transparent conducting impurity-doped ZnO thin films prepared on glass substrates by a dc magnetron sputtering (dc-MS) deposition, the obtainable lowest resistivity and the spatial resistivity distribution on the substrate surface were improved by a newly developed MS deposition method. The decrease of obtainable lowest resistivity as well as the improvement of spatial resistivity distribution on the substrate surface in Al- or Ga-doped ZnO (AZO or GZO) thin films were successfully achieved by inserting a very thin buffer layer, prepared using the same MS apparatus with the same target, between the thin film and the glass substrate. The deposition of the buffer layer required a more strongly oxidized target surface than possible to attain during a conventional dc-MS deposition. The optimal thickness of the buffer layer was found to be about 10 nm for both GZO and AZO thin films. The resistivity decrease is mainly attributed to an increase of Hall mobility rather than carrier concentration, resulting from an improvement of crystallinity coming from insertion of the buffer layer. Resistivities of 3 × 10^− 4 and 4 × 10^− 4Ω cm were obtained in 100 nm-thick-GZO and AZO thin films, respectively, incorporating a 10 nm-thick-buffer layer prepared at a substrate temperature around 200 °C.     

Electrical mechanism analysis of Al2O3 doped zinc oxide thin films deposited by rotating cylindrical DC magnetron sputtering

Cost efficient and large area deposition of superior quality Al₂O₃ doped zinc oxide (AZO) films is instrumental in many of its applications, including solar cell fabrication due to its numerous advantages over indium tin oxide (ITO) films. In this study, AZO films were prepared by a highly efficient rotating cylindrical direct current (DC) magnetron sputtering system using an AZO target, which has a target material utilization above 80%, on glass substrates in argon (Ar) ambient. A detailed analysis on the electrical, optical, and structural characteristics of AZO thin films was performed for the solar cell, as well as display applications. The properties of films were found to critically depend on deposition parameters, such as sputtering power, substrate temperature, working pressure, and film thickness. A low resistivity of ~ 5.5 × 10^− 4 Ω cm was obtained for films deposited at 2 kW, keeping the pressure, substrate temperature and thickness constant at 3 mTorr, 230 °C and ~ 1000 nm respectively. This was due to an increase in carrier mobility and large grain size. Mobility is found to be controlled by ionized impurity scattering within the grains, since the mean free path of carriers is much smaller than the grain size of the films. The AZO films showed a high transparency of ~ 90% in the long wavelength region. Our results offer a cost-efficient AZO film deposition method that can fabricate films with significant low resistivity and high transmittance that can be applied in thin-film solar cells, as well as thin film transistor (TFT) and non-volatile memory (NVM).     

The effect of annealing on Al-doped ZnO films deposited by RF magnetron sputtering method for transparent electrodes

In this study, transparent conducting Al-doped zinc oxide (AZO) films with a thickness of 150 nm were prepared on Corning glass substrates by the RF magnetron sputtering with using a ZnO:Al (Al₂O₃: 2 wt.%) target at room temperature. This study investigated the effects of the post-annealing temperature and the annealing ambient on the structural, electrical and optical properties of the AZO films. The films were annealed at temperatures ranging from 300 to 500 °C in steps of 100 °C by using rapid thermal annealing equipment in oxygen. The thicknesses of the films were observed by field emission scanning electron microscopy (FE-SEM); their grain size was calculated from the X-ray diffraction (XRD) spectra using the Scherrer equation. XRD measurements showed the AZO films to be crystallized with strong (002) orientation as substrate temperature increases over 300 °C. Their electrical properties were investigated by using the Hall measurement and their transmittance was measured by UV-vis spectrometry. The AZO film annealed at the 500 °C in oxygen showed an electrical resistivity of 2.24 × 10^− 3 Ω cm and a very high transmittance of 93.5% which were decreased about one order and increased about 9.4%, respectively, compared with as-deposited AZO film.     

Effect of deposition parameters and annealing temperature on the structure and properties of Al-doped ZnO thin films

Transparent conductive films of Al-doped ZnO (AZO) were deposited onto inexpensive soda-lime glass substrates by radio frequency (rf) magnetron sputtering using a ZnO target with an Al content of 3 wt%. The Taguchi method with a L₉ orthogonal array, signal-to-noise (S/N) ratio and analysis of variance (ANOVA) were employed to examine the performance characteristics of the coating operations. This study investigated the effect of the deposition parameters (rf power, sputtering pressure, thickness of AZO films, and substrate temperature) on the electrical, structural, morphological and optical properties of AZO films. The grey-based Taguchi method showed the electrical resistivity of AZO films to be about 9.15 × 10⁻³ Ω cm, and the visible range transmittance to be about 89.31%. Additionally, the films were annealed in a vacuum ambient (5.0 × 10⁻⁶ Torr) at temperatures of 400, 450, 500 and 600 °C, for a period of 30 min. It is apparent that the intensity of the X-ray peaks increases with annealing treatment, leading to improved crystallinity of the films. By applying annealing at 500 °C in a vacuum ambient for 30 min, the AZO films show the lowest electrical resistivity of 2.31 × 10⁻³ Ω cm, with about 90% optical transmittance in the visible region and a surface roughness of Ra = 12.25 nm.     

Highly conductive alumina-added ZnO ceramic target prepared by reduction sintering and its effects on the properties of deposited thin films by direct current magnetron sputtering

To obtain a suitable sputtering target for depositing transparent conducting Al-doped ZnO (AZO) films by using direct current (DC) magnetron sputtering, this study investigates the possibility of using atmosphere controlled sintering of Al₂O₃ mixed ZnO powders to prepare highly conductive ceramic AZO targets. Experimental results show that a gas mixture of Ar and CO could produce a sintered target with resistivity in the range of 2.23 × 10^− 4 Ω cm. The fairly low resistivity was mainly achieved by the formation of both aluminum substitution (Al_Zn) and oxygen vacancy (V_O), thus greatly increasing the carrier concentration. Compared to usual air sintered target, the thin film deposited by the Ar + CO sintered target exhibited lower film resistivity and more uniform spatial distribution of resistivity. A film resistivity as low as 6.8 × 10^− 4 Ω cm was obtained under the sputtering conditions of this study.     

The effects of impurity and temperature for transparent conducting oxide properties of Al:ZnO deposited by dc magnetron sputtering

Aluminum-doped zinc oxide films (ZnO:Al) were deposited on Si wafers and glass substrates by dc magnetron sputtering from a ZnO target mixed with 2 wt% Al₂O₃ for photovoltaic films. The effect of base pressure, additional oxygen, and substrate temperature were studied in detail. By dc magnetron sputtering at room temperature, the resistivity and the average transmittance in visible range was 2.3 × 10⁻³ Ω cm and 77.3%, respectively. And these were improved up to 3.3 × 10⁻⁴ Ω cm and 86% at the substrate temperature of 400 °C by high deposition rate and low impurity ambient. The mobility and the carrier concentration were improved by the increased preferred orientation of (002) plane and grain size of film with increasing deposition temperature. This advanced AZO film with good resistivity and transmittance can be expected as the front TCO of thin film solar cells.     

Al-doped ZnO thin films deposited by reactive frequency magnetron sputtering: H2-induced property changes

Al-doped ZnO (AZO) transparent conductive thin films have been prepared by radio-frequency magnetron sputtering with a ceramic target (98 wt.% ZnO, 2 wt.% Al₂O₃) in different Ar + H₂ ambient at a substrate temperature of 200 °C. To investigate the influence of H₂-flow on the properties of AZO films, H₂-flow was changed during the growth process with a fixed Ar-flow of 60 sccm. The results indicate that H₂-flow has a considerable influence on the transparent conductive properties of AZO films. The low resistivity in the order of 10^− 4 Ω cm and the high average transmittance more than 92% in the visible range were obtained for the samples prepared in the optimal H₂-flow range from 0.4 sccm to 1.0 sccm. In addition, the influence of H₂-flow on the structure and composition of AZO films have also been studied.     

Influence of Ga2O3 addition on transparent conductive oxide films of In2O3-ZnO

Influence of incorporation of Ga in amorphous In-Zn-O transparent conductive oxide films was investigated as a function of Zn/(Zn + In). For In-Zn-O films with no Ga₂O₃, the range of Zn/(Zn + In) ratio where the amorphous phase appears became narrow at a substrate temperature of 250 °C. With increasing Ga₂O₃ quantity, amorphous films were obtained even at a high substrate temperature of 250 °C in a wider range of Zn/(Zn + In) than that of In-Zn-O films with no Ga₂O₃. This means that the trend of crystallization at higher substrate temperature was disturbed with additional Ga incorporation. For the film deposited from ZnO:Ga (Ga₂O₃: 4.5-7.5 wt%) and In₂O₃ targets, we obtained a resistivity of 2.8 × 10⁻⁴ Ω cm, nearly the same value as that for an In-Zn-O film with no Ga₂O₃. The addition of more than 7.5 wt% Ga₂O₃ induced a widening of the optical band gap.     

Deposition of Al-doped ZnO films on polyethylene naphthalate substrate with radio frequency magnetron sputtering

100 nm Al-doped ZnO (AZO) thin films were deposited on polyethylene naphthalate (PEN) substrates with radio frequency magnetron sputtering using 2 wt.% Al-doped ZnO target at various deposition conditions including sputtering power, target to substrate distance, working pressure and substrate temperature. When the sputtering power, target to substrate distance and working pressure were decreased, the resistivity was decreased due to the improvement of crystallinity with larger grain size. As the substrate temperature was increased from 25 to 120 °C, AZO films showed lower electrical resistivity and better optical transmittance due to the significant improvement of the crystallinity. 2 wt.% Al-doped ZnO films deposited on glass and PEN substrates at sputtering power of 25 W, target to substrate distance of 6.8 cm, working pressure of 0.4 Pa and substrate temperature of 120 °C showed the lowest resistivity (5.12 × 10^− 3 Ω cm on PEN substrate, 3.85 × 10^− 3 Ω cm on glass substrate) and high average transmittance (> 90% in both substrates). AZO films deposited on PEN substrate showed similar electrical and optical properties like AZO films deposited on glass substrates.     

Ultrathin Al-doped transparent conducting zinc oxide films fabricated by pulsed laser deposition

Al-doped transparent conducting zinc oxide (AZO) films, approximately 20-110 nm-thick, were deposited on glass substrates at substrate temperatures between 200 and 300 °C by pulsed laser deposition (PLD) using an ArF excimer laser (λ = 193 nm). When fabricated at a substrate temperature of 260 °C, a 40-nm-thick AZO film showed a low resistivity of 2.61 × 10^− 4 Ω·cm, carrier concentration of 8.64 × 10²⁰ cm^− 3, and Hall mobility of 27.7 cm²/V·s. Furthermore, for an ultrathin 20-nm-thick film, a resistivity of 3.91 × 10^− 4 Ω·cm, carrier concentration of 7.14 × 10²⁰ cm^− 3, and Hall mobility of 22.4 cm²/V·s were obtained. X-ray diffraction (XRD) spectra, obtained by the θ-2θ method, of the AZO films grown at a substrate temperature of 260 °C showed that the diffraction peak of the ZnO (0002) plane increased as the film thickness increased from 20 to 110 nm. The full-width-at-half-maximum (FWHM) values were 0.5500°, 0.3845°, and 0.2979° for film thicknesses of 20, 40, and 110 nm, respectively. For these films, the values of the average transmittance in visible light wavelengths (400-700 nm) were 95.1%, 94.2%, and 96.6%, respectively. Field emission scanning electron microscopy (FE-SEM) and atomic force microscopy (AFM) observations showed that even the 20-nm-thick films did not show island structures. In addition, exfoliated areas or vacant and void spaces were not observed for any of the films.     

Rapid thermal-plasma annealing of ZnO:Al films for silicon thin-film solar cells

Rapid thermal annealing of sputter-deposited ZnO and Al-doped ZnO (AZO) films with and without an amorphous silicon (a-Si) capping layer was investigated using a radio-frequency (rf) argon thermal plasma jet at atmospheric pressure. The resistivity of bare ZnO films on glass decreased drastically from 10⁶ to 10³ Ω·cm at maximum surface temperatures T_max above 650 °C, whereas the resistivity increased from 10^− 4 to 10^− 3-10^− 2 Ω·cm for bare AZO films. On the other hand, the resistivity of AZO films with a 30-nm-thick a-Si capping layer remained below 10^− 4 Ω·cm, even after TPJ annealing at a T_max of 825 °C. X-ray diffraction and X-ray photoemission electron studies revealed that the film crystallization of both AZO and a-Si layers was promoted without the formation of an intermixing layer. Additionally, the crystallization of phosphorous- and boron-doped a-Si layers at the sample surface was promoted, compared to that of intrinsic a-Si under identical plasma annealing conditions. The role of the a-Si capping layer on sputter-deposited AZO and ZnO films during TPJ annealing is demonstrated. The effects of the mixing of phosphorous and boron impurities in a-Si:H during TPJ annealing of flat and textured AZOs are also discussed.     

Improvements of spatial resistivity distribution in transparent conducting Al-doped ZnO thin films deposited by DC magnetron sputtering

The relationship between two techniques developed for improving the resistivity distribution on the substrate surface in transparent conducting Al-doped ZnO (AZO) thin films prepared at a temperature of 200 °C by dc magnetron sputtering depositions (dc-MSD) using various sintered AZO targets has been investigated. One improvement method superimposes an rf component onto the dc-MSD (rf + dc-MSD). The other improvement method uses conventional dc-MSD with a low resistivity AZO target prepared under optimized conditions. An improvement of resistivity distribution resulted from a decrease in the resistivity of targets used in the preparation of AZO thin films by dc-MSD either with or without superimposing rf power. However, the resistivity distribution of AZO thin films resulting from depositions using rf-superimposed dc-MSD with lower-resistivity targets was not significantly improved over that of AZO thin films prepared by conventional dc-MSD using targets with the same low resistivities. The use of rf superimposition only resulted in improved resistivity distribution in thin films when the AZO targets had a resistivity higher than around 1 × 10^− 3 Ω cm. It should be noted that sintered AZO targets optimized for the preparation of AZO thin films with lower resistivity as well as more uniform resistivity distribution on the substrate surface tended to exhibit a lower resistivity.     

Physical properties of hydrogenated Al-doped ZnO thin layer treated by atmospheric plasma with oxygen gas

Hydrogenated Al-doped ZnO (H:AZO) thin films were deposited on glass substrates at room temperature by radio-frequency magnetron sputtering at various hydrogen flow rates. The addition of hydrogen improved the resistivity of the H:AZO films significantly. A thin insulating layer was produced on H:AZO films by atmospheric pressure plasma with Ar/O₂ reactive gas. The resistivity degenerated and the optical band gap of the oxygen plasma-treated H:AZO films decreased from 3.7 eV to 3.4 eV. This was attributed to a decrease in the hydrogen concentration at the film surface according to elemental depth analysis.     

The properties of transparent semiconductor Zn1 − xTixO thin films prepared by the sol-gel method

Transparent semiconductor thin films of Zn_1 − xTi_xO (0 ≦ x ≦ 0.12) were deposited on alkali-free glass substrates by the sol-gel method. The effects of Ti addition on the crystallization, microstructure, optical properties and resistivity of ZnO thin films were investigated. The as-coated films were preheated at 300 °C, and then annealed at 500 °C in air ambiance. X-ray diffraction results showed all polycrystalline Zn_1 − xTi_xO thin films with preferred orientation along the (002) plane. Ti incorporated within the ZnO thin films not only decreased surface roughness but also increased optical transmittance and electrical resistivity. In the present study, the Zn_0.88Ti_0.12O film exhibited the best properties, namely an average transmittance of 91.0% (an increase of ~ 12% over the pure ZnO film) and an RMS roughness value of 1.04 nm.     

Structural and electrical properties of sputtered indium-zinc oxide thin films

In this study, indium-zinc oxide (IZO) thin films have been prepared at a room temperature, 200 and 300 °C by radio frequency magnetron sputtering from a In₂O₃-12 wt.% ZnO sintered ceramic target, and their dependence of electrical and structural properties on the oxygen content in sputter gas, the substrate temperature and the post-heat treatment was investigated. X-ray diffraction measurements showed that amorphous IZO films were formed at room temperature (RT) regardless of oxygen content in sputter gas, and micro-crystalline and In₂O₃-oriented crystalline films were obtained at 200 and 300 °C, respectively. From the analysis on the electrical and the structural properties of annealed IZO films under Ar atmosphere at 200, 300, 400 and 500 °C, it was shown that oxygen content in sputter gas is a critical parameter that determines the local structure of amorphous IZO film, stability of amorphous phase as well as its eventual crystalline structure, which again decide the electrical properties of the IZO films. As-prepared amorphous IZO film deposited at RT gave specific resistivity as low as 4.48 × 10^− 4 Ω cm, and the highest mobility value amounting to 47 cm²/V s was obtained from amorphous IZO film which was deposited in 0.5% oxygen content in sputter gas and subsequently annealed at 400 °C in Ar atmosphere.     

The properties of radio frequency sputtered transparent and conducting ZnO:F films on polyethylene naphthalate substrate

We report on the properties of ZnO:F films deposited by RF sputtering on polyethylene naphthalate (PEN) substrates and compared them with films deposited on glass. Detailed and systematic investigations of various properties of films were deposited on PEN substrates were carried out as functions of thickness and annealing ambient. The films were deposited at room temperature and annealed at 150 °C in either Ar or 7% H₂/Ar ambients. These films exhibited carrier concentrations between 2 × 10¹⁸/cm³ and 9.5 × 10¹⁹/cm³, mobility between 3 and 11 cm²/V-s, and resistivity between 10^− 1 and 10^− 2 Ω-cm. Hall mobility variation with concentration has been explained assuming ionized impurity and lattice scattering to be the dominant mechanisms. The transmission of the films varied from 68 to 80% with increasing thickness and the absorption edge was limited by the absorption of the PEN substrate. The mechanical flexibility of the films was measured in terms of its critical radius of bending which was determined from the onset of a sharp increase in electrical resistance. The critical radius varied between 6.5 and 17 mm for film thicknesses varying from 20 to 200 nm. The thickness dependence of critical strain and critical radius can be explained by Griffith defect theory.     

Comparative study of resistivity characteristics between transparent conducting AZO and GZO thin films for use at high temperatures

This paper compares in detail the resistivity behavior of transparent conducting Al-doped and Ga-doped ZnO (AZO and GZO) thin films for use in an air environment at high temperatures. AZO and GZO thin films with thicknesses in the range from approximately 30 to 100 nm were prepared on glass substrates at a temperature of 200 °C by rf superimposed dc or conventional dc magnetron sputtering deposition, pulsed laser deposition or vacuum arc plasma evaporation techniques. In heat-resistance tests, the resistivity was measured both before and after heat tests for 30 min in air at a temperature up to 400 °C. The resistivity stability of AZO thin films was found to be always lower than that of GZO thin films prepared with the same thickness under the same deposition conditions, regardless of the deposition technique. However, the resistivity of all AZO and GZO thin films prepared with a thickness above approximately 100 nm was stable when heat tested at a temperature up to approximately 250 °C. It was found that the resistivity stability in both GZO and AZO thin films is dominated by different mechanisms determined by whether the thickness is below or above approximately 50 nm. With thicknesses above approximately 100 nm, the increase in resistivity found in GZO and AZO films after heat testing at a temperature up to 400 °C exhibited different characteristics that resulted from a variation in the behavior of Hall mobility.     

The low temperature synthesis of Al doped ZnO films on glass and polymer using pulsed co-magnetron sputtering: H2 effect

It has been reported that a small amount of hydrogen in argon plasma induces an increase in the crystallite size of the as-deposited films. In addition, control of the hydrogen partial pressure is expected to improve the carrier mobility by increasing the crystallinity of the film (larger crystal size and lower grain boundary effects). Al doped ZnO (AZO) films were deposited by co-CFUBM (closed field unbalanced magnetron) sputtering. The ultimate aim was to deposit transparent films on a polymer substrate with a low electrical resistivity. Therefore, the structural, optical and electrical properties of AZO films were investigated as a function of the hydrogen partial pressure. A minimum resistivity and maximum transparency of 8 × 10^− 4 Ω cm and 88.1% were obtained, respectively. A critical P_H2 was expected to improve the carrier mobility by increasing the crystallinity of the film. However, above this value, conductivity reduced due to the formations of oxides such as ZnO and Al₂O₃ in the AZO films.     

Transparent conducting Sc-codoped AZO film prepared from ZnO:Al-Sc by RF-DC sputtering

Al and Sc-codoped zinc oxide (also expressed as Sc-codoped AZO or ZnO:Al-Sc) films were sputtered on STN glass using RF power sources on ZnO and DC power sources on Al-1.7wt.% Sc alloy. X-ray diffraction (XRD) of the codoped films displayed that they are crystalline and textured at (002) and (103). Examination through transmission electron microscopy (TEM) depicted that these films consists of columnar grains. X-ray photoelectron spectroscopy (XPS) analysis of the films indicated that the O1s comprises O(I), O(II), O(III), and O(IV). The component O(I) centered at 530.00 ± 0.15eV was attributable to Sc₂O₃; the O(III) at 531.25 ± 0.20eV was to the oxygen deficient regions within the matrix of ZnO. The transmittance of visible light (i.e., wavelength in the range from 400 to 800nm) for the film was higher than 80%. The electrical resistivity is lower (1.76 < 2.81Ω-cm), the corrosion-resistance in 3.5% NaCl solution is better for the codoped film in comparison with the usual AZO. Heat treatment of the films (at 200-400°C for 1h) improved the optical transmittance, electrical conductivity, and corrosion-resistance in saline solution.     

Effects of substrate on the structural, electrical and optical properties of Al-doped ZnO films prepared by radio frequency magnetron sputtering

Transparent and conductive Al-doped ZnO (AZO) thin films were deposited on substrates including alkali-free glass, quartz glass, Si, and SiO₂ buffer layer on alkali-free glass by using radio frequency magnetron sputtering. The effects of different substrates on the structural, electrical and optical properties of the AZO films were investigated. It was found that the crystal structures were remarkably influenced by the type of the substrates due to their different thermal expansion coefficients, lattice mismatch and flatness. The AZO film (100 nm in thickness) deposited on the quartz glass exhibited the best crystallinity, followed sequentially by those deposited on the Si, the SiO₂ buffer layer, and the alkali-free glass. The film deposited on the quartz glass showed the lowest resistivity of 5.14 × 10^− 4 Ω cm among all the films, a carrier concentration of 1.97 × 10²¹ cm^− 3 and a Hall mobility of 6.14 cm²/v·s. The average transmittance of this film was above 90% in the visible light spectrum range. Investigation into the thickness-dependence of the AZO films revealed that the crystallinity was improved with increasing thickness and decreasing surface roughness, accompanied with a decrease in the film resistivity.