Hybrid silane-treated glass fabric/epoxy composites: tensile properties by micromechanical approach

The effect of interface modification on the interfacial adhesion and tensile properties of glass fabric/epoxy composites was evaluated in two directions of 0° and +45°. Herein, the glass fabric surface was modified by colloidal nanosilica particles and by a new blend of silane-coupling agents including both reactive and non-reactive silanes. Composite samples with high strength and toughness were obtained. A simultaneous improvement of tensile strength and toughness was observed for an epoxy composite reinforced with a hybrid-sized glass fabric including silane mixture and nanosilica. In fact, the incorporation of colloidal silica into the hybrid sizing dramatically modified the fiber surface texture and created mechanical interlocking between the glass fabric and resin. The results were analyzed by the rule of mixtures (ROM), Halpin–Tsai (H–T), and Chamis equations. It was found that the ROM equations provided approximate upper bound values for all investigated composite samples. In the samples containing nanosilica, the shear and elastic moduli values calculated by the Chamis and ROM equations showed good agreement with those obtained from experiments. However, in other samples, the values calculated by the H–T equation showed a better agreement with the experimental data. The analysis of fracture surfaces indicated that both silane and nanosilica particles had influence on the mode of failures at the interface.     

机织/针织混合铺层对复合材料力学性能的影响

为使纺织复合材料同时具有机织结构复合材料和针织结构复合材料的综合力学性能,通过混合铺层方式制备机织/针织混合结构复合材料。以芳纶机织平纹织物和针织罗纹织物为增强体,以环氧树脂为基体,调整复合材料中增强体的铺层顺序,利用真空辅助成型技术制备四层层压机织/针织混合结构复合材料。通过对复合材料拉伸性能、弯曲性能和冲击性能的测试,分析混合铺层和铺层顺序对芳纶环氧树脂复合材料力学性能的影响。结果表明,混合铺层和铺层顺序对芳纶环氧树脂复合材料的弯曲强度和冲击强度有较大影响,特别是对罗纹结构复合材料纬向弯曲强度和冲击强度的改善。当采用相同铺层方式,罗纹织物为受力面时,机织/针织混合结构复合材料具有较大弯曲强度和冲击强度。     

Preparation and evaluation of nano‐epoxy composite resins containing electrospun glass nanofibers

In this study, electrospun glass (structurally amorphous SiO₂) nanofibers (EGNFs) with diameters of ～ 400 nm were incorporated into epoxy resin for reinforcement and/or toughening purposes; the effects of silanization treatment (including different functional groups in silane molecules) and mass fraction of EGNFs on strength, stiffness, and toughness of the resulting nano‐epoxy composite resins were investigated. The experimental results revealed that EGNFs substantially outperformed conventional glass fibers (CGFs, with diameters of ～ 10 μm) in both tension and impact tests, and led to the same trend of improvements in strength, stiffness, and toughness at small mass fractions of 0.5 and 1%. The tensile strength, Young's modulus, work of fracture, and impact strength of the nano‐epoxy composite resins with EGNFs were improved by up to 40, 201, 67, and 363%, respectively. In general, the silanized EGNFs with epoxy end groups (G‐EGNFs) showed a higher degree of toughening effect, while the silanized EGNFs with amine end groups (A‐EGNFs) showed a higher degree of reinforcement effect. The study suggested that electrospun glass nanofibers could be used as reinforcement and/or toughening agent for making innovative nano‐epoxy composite resins, which would be further used for the development of high‐performance polymer composites. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Self‐healing and interfacially toughened carbon fibre‐epoxy composites based on electrospun core–shell nanofibres

Dual components of a self‐healing epoxy system comprising a low viscosity epoxy resin, along with its amine based curing agent, were separately encapsulated in a polyacrylonitrile shell via coaxial electrospinning. These nanofiber layers were then incorporated between sheets of carbon fiber fabric during the wet layup process followed by vacuum‐assisted resin transfer molding to fabricate self‐healing carbon fiber composites. Mechanical analysis of the nanofiber toughened composites demonstrated an 11% improvement in tensile strength, 19% increase in short beam shear strength, 14% greater flexural strength, and a 4% gain in impact energy absorption compared to the control composite without nanofibers. Three point bending tests affirmed the spontaneous, room temperature healing characteristics of the nanofiber containing composites, with a 96% recovery in flexural strength observed 24 h after the initial bending fracture, and a 102% recovery recorded 24 h after the successive bending fracture. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44956.     

钛酸钾晶须及硫酸钙晶须改性环氧树脂

应用硅烷及钛酸酯等偶联剂对钛酸钾晶须及硫酸钙晶须进行表面处理，考察晶须对环氧树脂力学性能、工艺性等的影响。研究表明，钛酸钾晶须经硅烷偶联剂处理后，能很好地改善复合材料的性能，硅烷的表面处理效果较钛酸酯的好。钛酸钾晶须添加到环氧树脂中后，材料的弯曲强度随晶须含量增大逐渐增大，在晶须含量为8％时达到最大值，之后性能稍有下降；材料的弯曲模量随晶须添加量的增加逐渐增大，冲击强度稍有降低。体系中添加硫酸钙晶须后，材料的性能也得到一定程度的提高。硫酸钙晶须对环氧树脂工艺性的影响较钛酸钾晶须小。SEM表明，晶须经合适的偶联剂表面改性后，与树脂基体的界面粘接得到有效改善。     

Concentration effect of γ‐glycidoxypropyltrimethoxysilane on the mechanical properties of glass fiber–epoxy composites

In this study, glass fibers were modified using γ‐glycidoxypropyltrimethoxysilane of different concentrations to improve the interfacial adhesion at interfaces between fibers and matrix. Effects of γ‐glycidoxypropyltrimethoxysilane on mechanical properties and fracture behavior of glass fiber/epoxy composites were investigated experimentally. Mechanical properties of the composites have been investigated by tensile tests, short beam tests, and flexural tests. The short‐beam method was used to measure the interlaminar shear strength (ILSS) of laminates. The tensile and flexural properties of composites were characterized by tensile and three‐point bending tests, respectively. The fracture surfaces of the composites were observed with a scanning electron microscope. On comparing the results obtained for the different concentrations of silane solution, it was found that the 0.5% GPS silane treatment provided the best mechanical properties. The ILSS value of heat‐cleaned glass fiber reinforced composite is enhanced by ∼59% as a result of the glass fiber treatment with 0.5% γ‐GPS. Also, an improvement of about 37% in tensile strength, about 78% in flexural strength of the composite with the 0.5% γ‐GPS treatment of glass fibers was observed. POLYM. COMPOS., 2009. © 2008 Society of Plastics Engineers     

聚丙烯/马来酸酐接枝聚丙烯/环氧树脂/玻璃纤维复合材料的制备及其性能研究

通过双螺杆挤出机制备了聚丙烯/马来酸酐接枝聚丙烯/环氧树脂/玻璃纤维（PP/PP-g-MAH/EP/GF）复合材料,并研究了PP-g-MAH含量、EP含量及固化剂对复合材料力学性能的影响。结果表明,PP-g-MAH含量为10份,含有固化剂EP的含量为3份时,复合材料的综合力学性能最佳;与不加EP的复合材料相比,其拉伸强度、弯曲强度、冲击强度分别提高了41 %、47 %、86 %。扫描电子显微镜分析表明,EP的加入明显改善了GF和PP基体的黏结强度。     

Mechanical,thermal, and burning properties of viscose fabric composites: Influence of epoxy resin modification

The influence of epoxy resin modification by 3‐aminopropyltriethoxysilane (APTES) on various properties of warp knitted viscose fabric is reported in this study. Dynamic mechanical, impact resistance, flexural, thermal properties, and burning behavior of the epoxy/viscose fabric composites are studied with respect to varying content of silane coupling agent. The results obtained for APTES‐modified epoxy resin based composites reinforced with unmodified viscose fabric composites are compared to unmodified epoxy resin based composites reinforced with APTES‐modified viscose fabric. The dynamic mechanical behavior of the APTES‐modified resin based composites indicates improved interfacial adhesion. The composites prepared from modified epoxy resin exhibited a twofold increase in impact resistance. The improved adhesion between the fiber and modified resin was also visible from the scanning electron microscope analysis of the impact fracture surface. There was less influence of resin modification on the flexural properties of the composites. The 5% APTES modification induced early degradation of composites compared to all other composites. The burning rate of all the composites under study is rated to be satisfactory for use in automotive interior applications. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46673.     

Epoxy/nano‐silica composites: Curing kinetics,glass transition temperatures,dielectric, and thermal–mechanical performances

Nano‐silica particles were employed for enhancement of epoxy vacuum pressure impregnating (V.P.I.) resin. The influences of nano‐silica particles on the curing reaction, glass transition temperatures, dielectric behavior, and thermomechanical performances were investigated. The activation energy (E) for the epoxy curing reaction was calculated according to Kissinger, Ozawa, and Friedman‐Reich‐Lev methods. The glass transition temperatures were determined by means of differential scanning calorimetry, dynamic mechanical analysis, dc conduction, and ac dielectric loss analysis. Relationships between the glass transformation behaviors, the thermomechanical performances, and the dielectric behaviors were discussed. The influences of nano‐silica particles on the mechanical properties were also discussed in terms of non‐notched charpy impact strength and flexural strength. The morphologies were studied by means of SEM and TEM. The results indicated that nano‐silica particles could effectively increase both the toughness and strength of epoxy resin at low loadings (no more than 3 wt %) when nano‐silica particles could be well dispersed in epoxy matrix without any great aggregations. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

碳纤维/聚苯并(噁)嗪复合材料的界面与力学性能的关系研究

本文采用含不同上胶剂的碳纤维与苯并(噁)嗪树脂复合,制备碳纤维/聚苯并(噁)嗪单向复合材料,研究了碳纤维表面上胶剂对于复合材料的层间剪切强度(ILSS)、弯曲性能、断口形貌及动态机械性能的影响.结果表明,含有环氧树脂上胶剂的碳纤维/苯并(噁)嗪树脂基复合材料(EPCF/PBZ)的ILSS和弯曲性能优于含非环氧类树脂上胶剂的碳纤维/苯并(噁)嗪树脂基复合材料(VECF/PBZ)和不含上胶剂的碳纤维/苯并(噁)嗪树脂基复合材料(USCF/PBZ).环氧树脂上胶剂改善了纤维与苯并(噁)嗪树脂的粘结性能,使复合材料的内耗峰峰高降低,能量损耗减小.电镜照片同样验证了这一结果.     

Unsaturated polyester‐toughened epoxy composites: Effect of sisal fiber on thermal and dynamic mechanical properties

In the present study, the mechanical and thermal properties of sisal fiber‐reinforced unsaturated polyester (UP)‐toughened epoxy composites were investigated. The sisal fibers were chemically treated with alkali (NaOH) and silane solutions in order to improve the interfacial interaction between fibers and matrix. The chemical composition of resins and fibers was identified by using Fourier‐transform infrared spectroscopy. The UP‐toughened epoxy blends were obtained by mixing UP (5, 10, and 15 wt%) into the epoxy resin. The fiber‐reinforced composites were prepared by incorporating sisal fibers (10, 20, and 30 wt%) within the optimized UP‐toughened epoxy blend. Scanning electron microscopy was used to analyze the morphological changes of the fibers and the adhesion between the fibers and the UP‐toughened epoxy system. The results showed that the tensile and flexural strength of (alkali‐silane)‐treated fiber (30 wt%) ‐reinforced composites increased by 83% and 55%, respectively, as compared with that of UP‐toughened epoxy blend. Moreover, thermogravimetric analysis revealed that the (alkali‐silane)‐treated fiber and its composite exhibited higher thermal stability than the untreated and alkali‐treated fiber systems. An increase in storage modulus and glass transition temperature was observed for the UP‐toughened epoxy matrix on reinforcement with treated fibers. The water uptake behavior of both alkali and alkali‐silane‐treated fiber‐reinforced composites is found to be less as compared with the untreated fiber‐reinforced composite. J. VINYL ADDIT. TECHNOL., 23:188–199, 2017. © 2015 Society of Plastics Engineers     

玻纤增强ABS复合材料的制备及性能

以丙烯腈-丁二烯-苯乙烯共聚物(ABS)及玻璃纤维(GF)为原料,以环氧树脂作为界面相容剂,研究了界面相容剂对玻璃纤维增强ABS复合材料力学性能及界面粘接的影响.结果表明:加入环氧树脂,玻纤增强ABS复合材料的力学性能明显提高;随着玻纤质量分数的增加,复合材料的拉伸强度、弯曲强度、冲击强度均逐渐增加;玻纤质量分数为30%时,GF/ABS/环氧树脂复合材料的拉伸强度比未改性的复合材料的拉伸强度提高了30%,弯曲强度提高了25%,冲击强度也提高了50%.     

Effect of organosilane coupling agents on microstructure and properties of nanosilica/epoxy composites

Three types of silane coupling agents, γ‐aminopropyltriethoxysilane, γ‐glycidoxypropyltrimethoxysilane, and γ‐methacryloxypropyltrimethoxysilane, were used as modifiers to modify the surface of the nanosilica, respectively, and the nanocomposites of the epoxy resin filled with nano‐sized silica modified by three silane coupling agents were prepared by physical blending. The properties of the modified silica nanoparticles were characterized by Fourier transform infrared spectrum and particle‐size analyzer. The microstructure, mechanical behavior, and heat resistant properties of the nanocomposites were investigated by transmission electron microscopy, scanning electron microscopy, thermo gravimetric analyses, differential thermal gravity, differential scanning calorimetry, and flexural tests. The results showed that these modifiers are combined to the surfaces of nanosilica by the covalent bonds, and they change the surface properties of nanosilica. The different structures of coupling agents have different effects on the dispersibility and stability of modified particles in the epoxy matrix. In comparison, the silica nanoparticles modified by γ‐glycidoxypropyltrimethoxysilane exhibit a good dispersivity. The nanocomposites with 4 wt% weight fraction nanosilica modified by γ‐glycidoxypropyltrimethoxysilane have higher thermal decomposing temperature and glass transition temperature than those of the other two composites with the same nanosilica contents, and they are raised by 43.8 and 8°C relative to the unmodified composites, respectively. The modified silica nanoparticles have good reinforcing and toughening effect on the epoxy matrix. The ultimate flexural strengths of the composites with 4 wt% nanoparticles modified by γ‐aminopropyltriethoxysilane, γ‐glycidoxypropyltrimethoxysilane, and γ‐methacryloxypropyltrimethoxysilane are increased by 10, 30, and 8% relative to the unmodified composites, respectively. The flexural fracture surfaces of modified composites present ductile fracture features. POLYM. COMPOS. 2012. © 2012 Society of Plastics Engineers     

Preparation and performance of nano‐SiO2 stabilized Pickering emulsion type sizing agent for glass fiber

The nano‐SiO₂ particles modified by silane coupling agent A‐1100 were used for preparing the vinyl ester resin (VE) Pickering emulsion. The stable emulsion could be served as the film former of sizing agent for glass fiber (GF). The influence of the wettability and the addition amount of nano‐SiO₂ on the stability of film former emulsion was explored. The effect of nano‐SiO₂ Pickering emulsion type sizing agent on the properties of GF was investigated. SEM images show that there existed a layer of sizing agent film with nano‐SiO₂ particles evenly on the GF surface. The abrasion resistance of the sized GF reached 3,579 times and the stiffness was 69 mm. The strand integrity also performed well. The fracture strength of GF bundles treated by Pickering emulsion type sizing agent increased by 28.6% to 0.504 N/Tex compared with that of the unsized GF bundles. The interlaminar shear strength (ILSS) of GF/VE composites sized by self‐made sizing agent which contained nano‐SiO₂ has improved, compared to the unsized GF reinforced VE composite. POLYM. COMPOS., 37:334–341, 2016. © 2014 Society of Plastics Engineers     

Mode I and Mode II delamination resistance and mechanical properties of woven glass/epoxy–PU IPN composites

The effect of polyurethane on the mechanical properties and Mode I and Mode II interlaminar fracture toughness of glass/epoxy composites were studied. Polyurethanes (PU) synthesized using polyols and toluene diisocyanate were employed as modifier for epoxy resin by forming interpenetrating polymer network. The PU/Epoxy IPN was used as matrix material for GFRP. PU modified epoxy composite laminates having varying PU contents were prepared. The effect of PU content on the mechanical properties like interlaminar fracture toughness (Mode I, G_1c and Mode II, G_IIc), tensile strength, flexural strength, and Izod impact strength were studied. The morphological studies were conducted on the fractured surface of the composite specimen by scanning electron microscopy (SEM). Tensile strength, flexural strength, and impact strength of PU‐modified epoxy composite laminates were found to increase inline with interlaminar fracture toughness (G_1c and G_IIc) with increasing PU content to a certain limit and then it was found to decrease with increase in PU content. It was observed that toughening of epoxy with PU increases the Mode I and Mode II delamination toughness up to 17 and 120% higher than that of untoughened composite specimen, respectively. POLYM. COMPOS., 2008. © 2008 Society of Plastics Engineers     

高低温老化对碳纤维复合材料芯棒结构性能的影响

采用拉挤工艺制备了碳纤维增强环氧树脂基复合材料芯棒,并对其进行高低温人工加速老化试验,以及对老化前后碳纤维复合材料芯棒的横截面、外观颜色和密度进行了测试和分析。结果表明,高低温老化使芯棒颜色加深,主要对芯棒的外层产生一定的影响,内部结构没有明显变化;老化后芯棒的密度比老化前减小约2.5%,并且不同老化周期对芯棒的密度基本不变。     

Effect of plate-like glass fillers on the mechanical properties of dental nanocomposites

In this study, glass flakes were incorporated into the spherical nanosilica component of the dental composites and its effect on the mechanical properties of these composites was investigated. To achieve a good interfacial adhesion between matrix resin and fillers, the particles were surface treated with a silane coupling agent (γ-MPS). Composites with different plate-like and spherical nanoparticle contents were prepared and their mechanical properties, including flexural strength, flexural modulus and fracture toughness were measured. The morphology of the particles and fracture surface of the composites were studied by SEM. The distribution of the flakes in the composite was also monitored using EDXA. Statistical analysis of the data was performed with ANOVA and the Tukey’s post hoc test was at a significance level of 0.05. The results showed that the flexural modulus and fracture toughness of specimens were improved with increasing the glass flake content up to 15 vol % which then declined upon further increase due to the stacking of the flakes on each other. A good interfacial adhesion was observed between matrix resin and particles in the SEM micrographs. The results of this study suggest that incorporation of glass flakes into the dental composites containing spherical nanosilica particles may enhance their mechanical properties.     

Preparation of multiscale graphene oxide‐carbon fabric and its effect on mechanical properties of hierarchical epoxy resin composite

Graphene oxide (GO) was used to modify the surface of carbon fiber layers through electrophoretic deposition, forming a multiscale reinforcement fabric. By adjusting the experimental parameters, the resulting GO‐carbon fabric showed productive and homogenous distribution of thin and less‐agglomerate GO platelets on carbon fiber surface, remarkably enlarging the surface area and roughness of carbon fabric. To investigate the effect of GO sheets on composites, GO‐carbon fabric and carbon fabric‐reinforced hierarchical epoxy resin composites were respectively manufactured. Mechanical tests demonstrated that after introducing GO flakes on carbon fabric, both the flexural strength and interlaminar shear strength of composite had achieved an increase, especially the interlaminar shear strength rising by 34%. Through fractography analysis, it was found that in pure carbon fabric‐reinforced epoxy composite, the fiber/matrix debonding fracture mechanism predominated, while after the GO decoration on carbon fiber surface, the composite featured a stronger interfacial bonding, leading to the enhancement in mechanical properties of hierarchical epoxy resin composite. POLYM. COMPOS., 37:1515–1522, 2016. © 2014 Society of Plastics Engineers     

Studies on Preparation and Property Researches of EP/SiC Thermal Conductivity Composites

The epoxy resin/silicon carbide thermal conductivity composites were prepared via casting method. The content of SiC and coupling reagents effecting on the thermal conductivity, mechanical and thermal properties of composites were investigated. Results revealed that the thermal conductivity properties of the composites were improved with the increasing mass fraction of SiC, and the thermal conductivity coefficient λ was 0.7152 W/mk with 50% mass fraction of SiC, being over 3 times of that of native epoxy resin. The flexural strength and impact strength of the EP/SiC composites increased firstly, but decreased with excessive addition of SiC, and the properties of EP/SiC composites were maximum with 10 wt% SiC. DSC and TGA analysis showed that the glass transition temperature (Tg) of composites decreased, but the heat resistance increased with the addition of SiC. SEM observation of impact fracture revealed that the impact strength had the relationships of large or small fracturing ability and the fracturing extended ability and the resin elasticity deformation.     

界面结合对GF/PDCPD复合材料性能的影响

界面结合性能对制备性能优异的复合材料具有重要意义。通过对双环戊二烯（DCPD）与玻璃纤维（GF）的浸润性进行研究，将其与等效环氧树脂比较，开发了一种与玻璃纤维具有较好结合性的DCPD树脂，用其制备出一种综合性能优异的玻璃纤维增强PDCPD基复合材料。通过动态接触角、90?拉伸强度和层间剪切强度实验，测定了不同树脂与玻璃纤维之间的粘附力，提供了玻璃纤维与不同树脂界面性能差异。结果表明，SCB-600 DCPD树脂与玻璃纤维的结合性较优，动态接触角为60.35??0.3?，90?拉伸强度为(42.3?1.6) MPa，层间剪切强度为(61.3?3.2) MPa，与1564环氧树脂相当。进一步优化了DCPD树脂质量分数，当树脂质量分数为30%?2%时，SCB-600 DCPD复合材料具有相对最优的力学性能，材料拉伸强度为(1180.1?4.1) MPa，弯曲强度为(1060.4?4.6) MPa，缺口冲击强度为(145.3?4.8) KJ/m2。其弯曲和拉伸强度与玻璃纤维增强环氧树脂基复合材料的性能基本相当，但缺口冲击强度优于1564环氧树脂。